APX9132 Hall Effect Micro Switch IC Features General Description • • • The APX9132, integrated circuit, is an ultra-sensitive, pole independent Hall-effect switch with a latched digital output. Micro Power Operation for Battery Applications Chopper Stabilized Amplifier A 2.5 volt to 3.5 volt operation and an unique clocking s c h e m e r e d u c e t h e a ve r a g e o p e r a t i n g p o we r Independent of North or South Pole Magnet, Easy for Manufacture • • requirements, either a north or south pole of sufficient flux will turn the output on; in the absence of a magnetic Small Size Package field, the output is off. The polarity independence and minimal power requirement allow this device to be easily Lead Free and Green Devices Available (RoHS Compliant) replaced reed switch for superior for signal conditioning. Advanced CMOS processing is used to take advantage of Applications • • • • low-voltage and low-power requirements, SOT-23-3 package provided a optimized package for most applications. Micro Switch Pin Configuration Handheld Wireless Application Wake Up Switch GND Clamp Shell Type Application Switch Magnet Switch in Low Duty Cycle Applications APX9132 VDD VOUT SOT-23-3 Ordering and Marking Information APX9132 Package Code A : SOT-23-3 AT : TSOT-23-3 Temperature Range I : -40 to 85 oC Handling Code TR : Tape & Reel Assembly Material G : Halogen and Lead Free Device Assembly Material Handling Code Temperature Range Package Code APX9132 A/AT: X - Date Code X32X Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020C for MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by weight). ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 1 www.anpec.com.tw APX9132 Absolute Maximum Ratings Symbol TA = 25°C unless otherwise noted Parameter Rating Unit VDD Supply Voltage 5 V VOUT Output Voltage 5 V IOUT Output Current ±1 mA TJ Junction Temperature Range 150 °C TSTG Storage Temperature Range -65 to +150 °C Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Thermal Characteristics Symbol θJA Parameter Typical Value Unit Junction-to-Ambient Resistance in Free Air (Note 2) SOT-23 TSOT-23 260 275 SOT-23 TSOT-23 0.385 0.364 ο C/W Power Dissipation, TA=25oC PD W Note 2: θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. Electrical Characteristics TA = 25°C, VDD=3V unless otherwise noted APX9132 Symbol VDD IDD IOFF Characteristic Supply Voltage Range Supply Current Output Leakage Current Test Conditions Unit Min. Typ. Max. 2.5 - 3.5 V Average - 5 10 µA Awake - 1.2 2 mA Sleep - 2 8 µA VOUT=3.5V, BRPN<B<BRPS - - 1.0 µA - - V Operating VOH Output High Voltage IOUT=-1mA VDD -0.4 VOL Output Low Voltage IOUT=1mA - 20 40 mV tawake Wake up Time - 180 - µs tperiod Period - 60 - ms d.c. Duty Cycle - 0.3 - % Chopping Frequency - 11 - kHz fc Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 2 www.anpec.com.tw APX9132 Magnetic Characteristics TA = 25°C, VDD=3V unless otherwise noted APX9132 Symbol Characteristic Test Conditions BOPS Unit Min. Typ. Max. 15 30 45 G -45 -30 -15 G 10 20 40 G -40 -20 -10 G - 10 - G Operate Points BOPN BRPS Release Points BRPN Bhys Hysteresis Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 3 www.anpec.com.tw APX9132 Typical Operating Characteristics Switching Points vs. Ambient Temperature Switching Points vs. Supply Voltage 40 40 BOPS 30 20 Switching Points (G) Switching Points (G) 20 BRPS 10 0 BRPN -10 -20 BRPS 10 0 -10 BRPN -20 -30 -30 -40 -40 TA=25oC BOPS 30 BOPN BOPN -40 -20 0 20 40 60 80 2.5 100 3 Ambient Temperature (°C) 3.5 4 4.5 Supply Voltage (V) Average Supply Current vs.Supply Voltage Average Supply Current vs. Ambient Temperature 10 20 TA=25oC 18 8 Average Supply Current (µA) Average Supply Current (µA) 5 6 4 2 16 14 12 10 8 6 4 2 0 0 -40 -20 0 20 40 60 80 2.5 100 Ambient Temperature (°C) Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 3 3.5 4 4.5 5 Supply Voltage (V) 4 www.anpec.com.tw APX9132 Typical Operating Characteristics (Cont.) Output Source Current vs. VDD-VOUT Voltage Output Sink Current vs. Output Low Voltage 5 10 9 4 VDD=4V 8 Output Sink Current (mA) Output Source Current (mA) VDD=5V VDD=4V 3 2 VDD=3V 1 7 VDD=5V 6 5 VDD=3V 4 3 2 1 0 0 0 0.2 0.4 0.6 0.8 1 0 0.2 0.4 0.6 0.8 1 Output Low Voltage (V) VDD-VOUT Voltage (V) Output Switch Waveform Output Switch Waveform VDD=3V CL=12pF VDD=3V CL=12pF Output Voltage (0.5V/div) Output Voltage (0.5V/div) 0 VOUT (0.5V/div) VOUT (0.5V/div) Time (50µs/div) Time (50µs/div) Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 5 www.anpec.com.tw APX9132 Pin Description PIN FUNCTION NO. NAME 1 VDD 2 VOUT When a magnetic field enters the hall element and exceeds the operate point BOPS (or less than BOPN) the output turns on (output is low). When the magnetic field is below the release point BRPS (or above BRPN), the output turns off (output is high). 3 GND Ground Connection Power Input Block Diagram VDD Awake & Sleep Timing Logic Dynamic Offset Cancellation Hall Plane Latch Circuit Chopper Amplifier VOUT GND Hysteresis Control Typical Application Circuit VOUT VDD + APX9132 2.5V-3.5V 0.1µF GND - SOT-23 (Top View) Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 6 www.anpec.com.tw APX9132 Function Description Operation The output of APX9132 switches low (turn-on) when in presence of strong flux density facing the marked side of package exceeds the operate point BOPS (or is less than BOPN). After turn-on, the output is capable of sinking up to 1mA and the output voltage is low (turn-on). In absence of flux density below the release point BRPS (or increased above BRPN), the APX9132 output switches high (turns off). After turn-off, the output is capable of sourcing up to 1mA and the output voltage is high (turn-off). The difference in the magnetic operated and released point is the hysteresis (B hys) of the device. This built-in hysteresis allows clean switching of the output even in the presence of external mechanical bouncing vibration and electrical noise. OUTPUT OFF BOPN BOPS OUTPUT VOLTAGE 5V MAX BRPN 0 -B BRPS 0 OUTPUT ON +B MAGNETIC FLUX Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 7 www.anpec.com.tw APX9132 Application Information It is strongly recommended that an external bypass capacitor be connected (is close to the Hall sensor) between the supply and ground of the device to reduce both external noise and noise generated by the chopper-stabilization technique. This is especially true due to the relatively high impedance of battery supplies. Pole-independent The pole-independent sensing technique allows for operation with either a north or south pole magnet orientation, enhancing the manufacturability of the device. The state-of-the-art technology provides the same output polarity for either pole in presence. Awake & Sleep Internal awake & sleep timing block circuit activates the sensor for 180 µs and deactivates it for the remainder of the period (60 ms). A short “awake” time allows for stabilization prior to the sensor sampling and data latching on the falling edge of the timing pulse. While in sleep cycle, the output is latched in its previous state. Chopper Stabilized Technique The chopper stabilized technique cancels the mismatching of the hall element, the amplifier offset voltage and temperature sensitive drift by the dynamic offset cancellation and switched capacitor technique. This technique produces devices have an extremely stable Hall output voltage, therefore, the magnetic switch points are stable. Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 8 www.anpec.com.tw APX9132 Package Information SOT-23-3 D e E E1 SEE VIEW A c b 0.25 A L GAUGE PLANE SEATING PLANE 0 A1 A2 e1 VIEW A S Y M B O L SOT-23-3 INCHES MILLIMETERS MIN. MIN. MAX. A MAX. 0.057 1.45 A1 0.00 0.15 0.000 0.006 A2 0.90 1.30 0.035 0.051 b 0.30 0.50 0.012 0.020 c 0.08 0.22 0.003 0.009 D 2.70 3.10 0.106 0.122 E 2.60 3.00 0.102 0.118 E1 1.40 1.80 0.055 e 0.95 BSC e1 0.071 0.037 BSC 1.90 BSC 0.075 BSC L 0.30 0.60 0 0° 8° 0.012 0° 0.024 8° Note : Dimension D and E1 do not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side. Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 9 www.anpec.com.tw APX9132 Package Information TSOT-23-3 D e E E1 SEE VIEW A b c 0.25 A GAUGE PLANE SEATING PLANE L A1 A2 e1 VIEW A TSOT-23-3 S Y M B O L MIN. MAX. MIN. MAX. A 0.75 0.80 0.030 0.031 A1 0.03 0.05 0.001 0.002 A2 0.70 0.75 0.028 0.030 0.020 MILLIMETERS INCHES b 0.30 0.50 0.012 c 0.08 0.20 0.003 0.008 D 2.70 3.10 0.106 0.122 E 2.60 3.00 0.102 0.118 E1 1.40 1.80 0.055 0.071 e 0.95 BSC e1 1.90BSC 0.037 BSC 0.075 BSC L 0.30 0.60 0 0° 8° 0.012 0° 0.024 8° Note : Dimension D and E1 do not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side. Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 10 www.anpec.com.tw APX9132 Carrier Tape & Reel Dimensions P0 P2 P1 A B0 W F E1 OD0 K0 A0 OD1 B A B T SECTION A-A SECTION B-B H A d T1 Application SOT-23-3 Application TSOT-23-3 A H T1 C d D W E1 F 178.0±2.00 50 MIN. 8.4+2.00 -0.00 13.0+0.50 -0.20 1.5 MIN. 20.2 MIN. 8.0±0.30 1.75±0.10 3.5±0.05 P0 P1 P2 D0 D1 T A0 B0 K0 4.0±0.10 4.0±0.10 2.0±0.05 1.5+0.10 -0.00 1.0 MIN. 0.6+0.00 -0.40 3.20± 0.20 3.10±0.20 1.50±0.20 A H T1 C d D W E1 F 178.0±2.00 50 MIN. 8.4+2.00 -0.00 13.0+0.50 -0.20 1.5 MIN. 20.2 MIN. 8.0±0.30 1.75±0.10 3.5±0.05 P0 P1 P2 D0 D1 T A0 B0 K0 2.0±0.10 1.5+0.10 -0.00 1.0 MIN. 0.6+0.00 -0.40 3.20± 0.20 3.10±0.20 1.50±0.20 4.0±0.10 4.0±0.10 Devices Per Unit Package Type SOT-23-3 TSOT-23-3 Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 Unit Tape & Reel Tape & Reel Quantity 3000 3000 11 www.anpec.com.tw APX9132 Taping Direction Information (T)SOT-23-3 USER DIRECTION OF FEED Classification Profile Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 12 www.anpec.com.tw APX9132 Classification Reflow Profiles Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly 100 °C 150 °C 60-120 seconds 150 °C 200 °C 60-120 seconds 3 °C/second max. 3°C/second max. 183 °C 60-150 seconds 217 °C 60-150 seconds See Classification Temp in table 1 See Classification Temp in table 2 Time (tP)** within 5°C of the specified classification temperature (Tc) 20** seconds 30** seconds Average ramp-down rate (Tp to Tsmax) 6 °C/second max. 6 °C/second max. 6 minutes max. 8 minutes max. Preheat & Soak Temperature min (Tsmin) Temperature max (Tsmax) Time (Tsmin to Tsmax) (ts) Average ramp-up rate (Tsmax to TP) Liquidous temperature (TL) Time at liquidous (tL) Peak (Tp)* package body Temperature Time 25°C to peak temperature * Tolerance for peak profile Temperature (Tp) is defined as a supplier minimum and a user maximum. ** Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum. Table 1. SnPb Eutectic Process – Classification Temperatures (Tc) 3 Package Thickness <2.5 mm Volume mm <350 235 °C Volume mm ≥350 220 °C ≥2.5 mm 220 °C 220 °C 3 Table 2. Pb-free Process – Classification Temperatures (Tc) Package Thickness <1.6 mm 1.6 mm – 2.5 mm ≥2.5 mm Volume mm <350 260 °C 260 °C 250 °C 3 Volume mm 350-2000 260 °C 250 °C 245 °C 3 Volume mm >2000 260 °C 245 °C 245 °C 3 Reliability Test Program Test item SOLDERABILITY HOLT PCT TCT ESD Latch-Up Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 Method JESD-22, B102 JESD-22, A108 JESD-22, A102 JESD-22, A104 MIL-STD-883-3015.7 JESD 78 13 Description 5 Sec, 245°C 1000 Hrs, Bias @ 125°C 168 Hrs, 100%RH, 2atm, 121°C 500 Cycles, -65°C~150°C VHBM≧2KV, VMM≧200V 10ms, 1tr≧100mA www.anpec.com.tw APX9132 Customer Service Anpec Electronics Corp. Head Office : No.6, Dusing 1st Road, SBIP, Hsin-Chu, Taiwan Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 2F, No. 11, Lane 218, Sec 2 Jhongsing Rd., Sindian City, Taipei County 23146, Taiwan Tel : 886-2-2910-3838 Fax : 886-2-2917-3838 Copyright ANPEC Electronics Corp. Rev. A.4 - Apr., 2009 14 www.anpec.com.tw