ETC ARGOS-A10X

Argos2D - A10x
User Manual
Version 1.1
Bluetechnix GmbH
Waidhausenstraße 3/19
A-1140 Vienna
AUSTRIA
[email protected]
www.bluetechnix.com
Argos®2D – A100 – User Manual
Document No.: 900-308 / B
Publication date: April 9, 2013
Subject to change without notice. Errors excepted.
This document is protected by copyright. All rights reserved. No part of this document may be reproduced or
transmitted for any purpose in any form or by any means, electronically or mechanically, without expressly
written permission by Bluetechnix GmbH.
Windows is a registered trademark of Microsoft.
© Bluetechnix 2013
Table of Contents
1
General Information .......................................................................................................................... 5
1.1
2
Overview ........................................................................................................................................... 6
2.1
System Architecture .................................................................................................................. 6
2.2
Models ....................................................................................................................................... 6
2.2.1
Argos2D – A100 (150-1001-1) ........................................................................................... 7
2.2.2
Argos2D – A101 (150-1002-1) ........................................................................................... 7
2.2.3
Argos2D – A102 (150-1003-1) ........................................................................................... 7
2.2.4
Argos2D – A103 (150-1004-1) ........................................................................................... 7
2.2.5
Argos2D – A104 (150-1005-1) ........................................................................................... 7
2.3
3
4
Symbols Used ........................................................................................................................... 5
Interfaces & Connectors ........................................................................................................... 8
Software Installation ......................................................................................................................... 9
3.1
Software-Development-Kit SDK ............................................................................................... 9
3.2
Drivers ....................................................................................................................................... 9
3.3
Console ..................................................................................................................................... 9
Hardware Installation ..................................................................................................................... 10
4.1
Connecting the Core Module and the Carrier Board .............................................................. 10
4.2
Connecting CM and CB with housing base ........................................................................... 11
4.3
Connecting the ISM with front plane ...................................................................................... 12
4.4
Connecting the 30pin flex-foil cable to the ISM ..................................................................... 12
4.5
Connecting ISM to housing base ........................................................................................... 12
4.6
Inserting the µSD-Card and the coin cell ................................................................................ 13
4.7
Connecting the housing cover with the base ......................................................................... 14
5
Getting Started ............................................................................................................................... 15
6
Programming Environment ............................................................................................................ 16
Use Eclipse IDE for C/C++ developers or an editor of your choice. ................................................. 16
6.1
7
Setting up the tool chain ......................................................................................................... 16
Appendix ........................................................................................................................................ 17
7.1
Electrical Specifications .......................................................................................................... 17
7.1.1
Operating Conditions ....................................................................................................... 17
7.1.2
Maximum Ratings ............................................................................................................ 17
7.1.3
ESD Sensitivity ................................................................................................................. 17
7.2
Connector and Interface Description ...................................................................................... 18
7.2.1
Reset button a(S4) ........................................................................................................... 18
7.2.2
HDMI connector b(X10) ................................................................................................... 18
7.2.3
Power connector c(X10) .................................................................................................. 18
© Bluetechnix 2013
7.2.4
RJ45 Ethernet connector d(X8)........................................................................................ 18
7.2.5
Status LED e(V7) .............................................................................................................. 18
7.2.6
USB-OTG connector f(X6) ............................................................................................... 18
7.2.7
ISM connector g(X9) ........................................................................................................ 18
7.2.8
µSD-Card holder h(X7)..................................................................................................... 19
7.2.9
JTAG connector i(X12) ..................................................................................................... 19
7.2.10
I/O extender connector j(X11) .......................................................................................... 19
7.2.11
RTC-battery holder k(G1) ................................................................................................ 20
7.2.12
Reset button l(S2) ............................................................................................................ 20
7.2.13
Boot mode switch m(S1) ................................................................................................. 20
7.2.14
Core Module connectors n(X1, X2, X3) ........................................................................... 21
7.3
Mechanical Outline.................................................................................................................. 22
7.4
Support ................................................................................................................................... 22
7.4.1
General Support............................................................................................................... 22
7.4.2
Board Support Packages ................................................................................................ 22
7.4.3
i.MX Freescale Software Support .................................................................................... 22
7.5
Dependability .......................................................................................................................... 23
7.5.1
8
Product History .............................................................................................................................. 24
8.1
9
MTBF ............................................................................................................................... 23
Version Information ................................................................................................................. 24
8.1.1
Argos2D – A100 (150-1001-1) ......................................................................................... 24
8.1.2
Argos2D – A101 (150-1002-1) ......................................................................................... 24
8.1.3
Argos2D – A102 (150-1003-1) ......................................................................................... 24
8.1.4
Argos2D – A103 (150-1004-1) ......................................................................................... 24
8.1.5
Argos2D – A104 (150-1005-1) ......................................................................................... 24
8.2
Anomalies ................................................................................................................................ 24
8.3
Document Revision History .................................................................................................... 25
Index ............................................................................................................................................... 26
© Bluetechnix 2013
© Bluetechnix GmbH 2013
All Rights Reserved.
The information herein is given to describe certain components and shall not be considered as a guarantee
of characteristics.
Terms of delivery and rights of technical change reserved.
We hereby disclaim any warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Bluetechnix makes and you receive no warranties or conditions, express, implied, statutory or in any
communication with you. Bluetechnix specifically disclaims any implied warranty of merchantability or fitness
for a particular purpose.
Bluetechnix takes no liability for any damages and errors causing of the usage of this board. The user of this
board is responsible by himself for the functionality of his application. He is allowed to use the board only if
he has the qualification. More information is found in the General Terms and Conditions (AGB).
Information
For further information on technology, delivery terms and conditions and prices please contact Bluetechnix
(http://www.bluetechnix.com).
Warning
Due to technical requirements components may contain dangerous substances.
© Bluetechnix 2013
Hardware User Manual - Argos2D - A10x
1
Last change: 9 April 2013
Version 1.1
General Information
This guide applies to all smart cameras based on the Argos® smart camera platform from Bluetechnix
GmbH. Follow this guide chapter by chapter to set up and understand your product. If a section of this
document only applies to certain camera models, this is indicated at the beginning of the respective section.
1.1
Symbols Used
This guide makes use of a few symbols and conventions:
Warning
Indicates a situation which, if not avoided, could result in minor or moderate injury and/or
property damage or damage to the device.
Caution
Indicates a situation which, if not avoided, may result in minor damage to the device, in
malfunction of the device or in data loss.
Note
Notes provide information on special issues related to the device or provide information that will
make operation of the device easier.
Procedures
A procedure always starts with an headline
1. The number indicates the step number of a certain procedure you are expected to
follow. Steps are numbered sequentially.
This sign  indicates an expected result of your action.
References
This symbol indicates a cross reference to a different chapter of this manual or to an
external document.
© Bluetechnix 2013
Page | 5
Hardware User Manual - Argos2D - A10x
2
Last change: 9 April 2013
Version 1.1
Overview
2.1
System Architecture
•
Video/Image processing
•
Data transmission
ISM
MT9M131-C
MT9M025-M/C
MT9M031-M/C
Cable
Data capturing
Camera
Interface
•
Camera
Interface
The Argos2D – A10x is designed to cover the needs for an intelligent image sensor with a high flexibility in
data transmission. The typical workflow can be divided in three actions:
CM-i.MX53
1GHz
4MB NOR
DC-Plug
Module
1GB DDR2
2GB NAND
USB-OTG
Active
Components
Reset Buttons
RGB LED
RTC
RGB-LED
Driver
µSD Card Slot
JTAG
I/O Extender
HDMI
Transmitter
RJ45
HDMI
User Interfaces
Connectors
Figure 2.1: System Architecture
The Bluetechnix standard Image Sensor Interface (BLT-ISM-Connector) allows connecting various image
sensors to the Argos2D – A10x (i.e. ISM-MT9M025, ISM-MT9M131 or ISM-MT9P031).
To transmit the captured and processed data there are various interfaces on the Argos2D – A10x. Depending
on the needed transmission rate you can select between USB, Ethernet, CAN (optional) or just store the data
on a micro-SD-card.
If there is the need to visualize the processed data or simply for visual debugging, an HDMI output is
available on the Argos2D – A10x.
2.2
Models
All Argos2D A10x cameras are equipped with the i.MX carrier board, which contains all peripherals, the core
module mount and interfaces including the ISM-connector, the CM-i.MX53 SoM as CPU board, the housing
and the selected ISM.
© Bluetechnix 2013
Page | 6
Hardware User Manual - Argos2D - A10x
Last change: 9 April 2013
Version 1.1
Front View
a
b
c
Side View
c
d
e
Back View
f
Figure 2.2: Argos2D – A10x views
a. ISM (Images Sensor Module) changeable
b. Front panel
c. CS-Mount holder
d. Housing cover
e. Housing base
f.
2.2.1
Rear panel with user interface and peripherals connectors
Argos2D – A100 (150-1001-1)
The A100 comes with the MT9M131 color, image sensor form Aptina, module. The sensor has a 1/3-inch (5:4)
format with 1280 x 1024 pixels.
2.2.2
Argos2D – A101 (150-1002-1)
The A101 comes with the MT9M025 monochrome, image sensor form Aptina, module. The sensor has a 1/3inch (4:3) format with 1280 x 960 pixels.
2.2.3
Argos2D – A102 (150-1003-1)
The A102 comes with the MT9M025 color, image sensor form Aptina, module. The sensor has a 1/3-inch (4:3)
format with 1280 x 960 pixels.
2.2.4
Argos2D – A103 (150-1004-1)
The A103 comes with the MT9P031 monochrome, image sensor form Aptina, module. The sensor has a
1/2.5-inch (4:3) format with 2592 x 1944 pixels.
2.2.5
Argos2D – A104 (150-1005-1)
The A104 comes with the MT9P031 color, image sensor form Aptina, module. The sensor has a 1/2.5-inch
(4:3) format with 2592 x 1944 pixels.
© Bluetechnix 2013
Page | 7
Hardware User Manual - Argos2D - A10x
2.3
Last change: 9 April 2013
Version 1.1
Interfaces & Connectors
All Argos2D – A10x cameras are equipped with the same connectors and interfaces.
c
d
h
g
i
j
d
a
c
b
a
e
f
n
k
l
m
d
c
a
Figure 2.3: Argos2D – A10x connectors and interfaces
a. Reset button
b. HDMI connector
c. Power connector
d. RJ45 Ethernet connector
e. Status LED
f.
USB-OTG connector
g. ISM connector
h. µSD-Card holder
i.
JTAG connector
j.
I/O extender connector
k.
RTC-battery holder
l.
Reset button
m. Boot mode switch
n. Core Module connectors
© Bluetechnix 2013
Page | 8
Hardware User Manual - Argos2D - A10x
3
3.1
Last change: 9 April 2013
Version 1.1
Software Installation
Software-Development-Kit SDK
The SDK is build up on Linux. Bluetechnix offers a Board Support Package that is based on the U-Boot boot
loader and the Linux kernel. The build environment is LTIB, the Linux Target Image Builder, which is
Freescale's preferred way to offer Linux board support packages. Bluetechnix provides a patch set that is
installed on top of Freescale's i.MX53 LTIB BSP. A guide for downloading and installing the SDK can be
found in the CM-i.MX53 Software User Manual.
3.2
Drivers
If your Operating system does not install the drivers for a virtual comport, a USB-UART driver installation
guide can be found here.
3.3
Console
An installation guide for a serial console can be found here.
© Bluetechnix 2013
Page | 9
Hardware User Manual - Argos2D - A10x
4
Last change: 9 April 2013
Version 1.1
Hardware Installation
Caution
Only assemble and dissemble electronic in an ESD-protected environment.
4.1
Connecting the Core Module and the Carrier Board
1. Put the carrier board with the bottom side up on a base.
2. Take the core module and align in on the connectors of the carrier board. Be aware that the CM and
the CB is parallel
3. Connect the CM with appropriate force on the marked spots to the CB.
4. Check if the CM is fully aligned on the CB
5. Take three M2 x 5mm screws and mount it.
1
2
3
4
5
Figure 4.1: Connecting the Core Module and the Carrier Board
© Bluetechnix 2013
Page | 10
Hardware User Manual - Argos2D - A10x
4.2
Last change: 9 April 2013
Version 1.1
Connecting CM and CB with housing base
1. Take the rear plane and the housing base.
2. Take two M2.9 x 5mm self-tapping screws and mount it.
3. Take the CM-CB compound with the CM looking down. First insert the connectors into the rear
plane and then push the CB down to the housing base.
4. Take two M2.9 x 5mm self-tapping screws and mount it on the front.
2
3
1
3
4
Figure 4.2: Connecting CM and CB with housing base
© Bluetechnix 2013
Page | 11
Hardware User Manual - Argos2D - A10x
4.3
Last change: 9 April 2013
Version 1.1
Connecting the ISM with front plane
1. Usually the ISM comes mounted with a CS mount holder. This is fixed with two M2 x 5mm srews
2. Take the ISM and align it on the front plane, by using the locating pins.
3. Take four M2.9 x 8mm self-tapping screws and mount them together.
2
1
3
Figure 4.3: Connecting the ISM with front plane
4.4
Connecting the 30pin flex-foil cable to the ISM
1. Take a look on the ISM. There is the possibility that more than one ISM connector is populated, if
that’s the case you must use that one with an i.MX mark besides. The flex foil cable must have the
contacts on the same side.
2. Pull out the lock of the connector with appropriate force simultaneously on both sides.
3. Insert the flex-foil cable with the visible contacts showing away from the ISM.
4. Secure the cable by pushing the lock back in.
1
2
3
4
5
Figure 4.4: Connecting flex-foil cable with ISM
4.5
Connecting ISM to housing base
1. Take the housing base including the CB and also take the ISM with connected front plane and flexfoil cable.
2. Pull out the lock of the connector with appropriate force simultaneously on both sides.
3. Pull out the lock of the connector with appropriate force simultaneously on both sides.
© Bluetechnix 2013
Page | 12
Hardware User Manual - Argos2D - A10x
4. Insert the flex-foil cable with the visible contacts showing away from the ISM.
Last change: 9 April 2013
Version 1.1
5. Secure the cable by pushing the lock back in.
6. Insert the ISM into the housing base
7. Turn the whole camera around and mount two M2.9 x 8mm self-tapping screws on the bottom.
1
2
3
4
5
6
7
Figure 4.5: Connecting ISM and front plane to housing base
4.6
Inserting the µSD-Card and the coin cell
1. Open the µSD-Card slot by pushing the slot with appropriate force to the right and then up.
2. Insert the µSD-Card.
3. Close the slot by pushing them town and to the left.
© Bluetechnix 2013
Page | 13
Hardware User Manual - Argos2D - A10x
Last change: 9 April 2013
Version 1.1
4. Push the 12mm coin cell with the positive side up and appropriate force into the holder.
4
1
3
2
Figure 4.6: Inserting the µSD-Card and the coin cell
4.7
Connecting the housing cover with the base
1. Put the housing cover over the base
2. Take two M2.9 x 8mm self-tapping screws and mount them in front of the cover.
3. Take two M2.9 x 18mm self-tapping screws and mount them in back of the cover.
2
1
3
Figure 4.7: Connecting the housing cover with the base
© Bluetechnix 2013
Page | 14
Hardware User Manual - Argos2D - A10x
5
Last change: 9 April 2013
Version 1.1
Getting Started
A Guide how to start with your Argos®2D A100 Camera based on the CM-i.MX53 SoM can be found here.
© Bluetechnix 2013
Page | 15
Hardware User Manual - Argos2D - A10x
6
Last change: 9 April 2013
Version 1.1
Programming Environment
Use Eclipse IDE for C/C++ developers or an editor of your choice.
6.1
Setting up the tool chain
The tool chain gets installed with the Software-Development-Kit SDK.
© Bluetechnix 2013
Page | 16
Hardware User Manual - Argos2D - A10x
7
Last change: 9 April 2013
Version 1.1
Appendix
7.1
7.1.1
Electrical Specifications
Operating Conditions
Symbol
VIN
IIN
V3V3
I3V3
VOH
VOL
Parameter
Input supply voltage
Input current @ 12V
Extender Voltage Supply
Extender Current Supply
High level output voltage
Low level output voltage
Min
12
3.0
2.31
-
Typical
12
300
3.3
-
Max1
16
500
3.6
300
0.99
Unit
V
mA
V
mA
V
V
Table 7.1: Electrical characteristics
1
An overstepping of these maximums may cause permanent damage of the CM
The voltage levels and currents are only correct with the Bluetechnix default PMIC settings.
7.1.2
Maximum Ratings
Stressing the device above the rating listed in the absolute maximum ratings table may cause permanent
damage to the device. These are stress ratings only. Operation of the device at these or any other conditions
greater than those indicated in the operating sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Symbol
VIN
VIO
OH /IOL
TAMB
TSTO
φAMB
Parameter
Input supply voltage
Input or output voltage
Current per pin
Ambient temperature
Storage temperature
Relative ambient humidity
Min
-0.5
-0.5
0
0
-55
-
Max
16
3.6
10
701
150
90
Unit
V
V
mA
°C
°C
%
Table 7.2: Absolute maximum ratings
If extreme high ambient temperatures are expected (75°C in industrial environments or 60°C for commercial
products), the user has to apply a heat spreader on CPU and DDR-RAM (avoid heat accumulation!). In
addition the die temperature should be monitored regularly, so that the CPU and RAM clock can be throttled
if necessary.
1
7.1.3
ESD Sensitivity
ESD (electrostatic discharge) sensitive device. Charged devices and circuit
boards can discharge without detection. Although this product features patented
or proprietary protection circuitry, damage may occur on devices subjected to
high energy ESD. Therefore, proper ESD precautions should be taken to avoid
performance degradation or loss of functionality.
© Bluetechnix 2013
Page | 17
Hardware User Manual - Argos2D - A10x
7.2
Last change: 9 April 2013
Version 1.1
Connector and Interface Description
7.2.1
Reset button a(S4)
The push button performs a factory reset. This function is not implemented in Software.
7.2.2
HDMI connector b(X10)
The HDMI connector provides a standard interface for digital video and audio signals. The HDMI/DVI
transmitter is preprocessing the video signal from the IPU. The audio stream comes from the AUD5 interface
of the i.MX53x.
7.2.3
Power connector c(X10)
The Argos2D - A10x works with a single power supply of 12V to 16V.
7.2.4
RJ45 Ethernet connector d(X8)
As the Ethernet PHY is already integrated on the Core Module, the LAN signals are routed directly to a RJ45
LAN connector.
7.2.5
Status LED e(V7)
The RGB LED is connected to the TCA62724FMG RGB-LED driver and can be used for status signaling.
7.2.6
USB-OTG connector f(X6)
The i.MX53 USB-OTG internal USB-OTG PHY is routed to a mini USB-A/B connector.
7.2.7
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
ISM connector g(X9)
Signal Name
VCAMA
GND
SADDR
CAMCLK
NRESET
SIO.C
SIO.D
VCAMC
GND
PPI0.CLK
PPI0.SY2
PPI0.SY1
PF45
STROBE
PPI0.D0
PPI0.D1
PPI0.D2
PPI0.D3
VCAMIO
© Bluetechnix 2013
Type
PWR
PWR
NC
O
O
O
I/O
PWR
PWR
I
I
I
O
I
I
I
I
I
PWR
Description
Camera Analog Voltage Supply
Power Ground
Not Connected
Camera Master Clock
Global Reset
Configuration Bus Clock Line
Configuration Bus Data Line
Camera Core Voltage Supply
Power Ground
Pixel Clock
VSYNC
HSYNC
Camera Trigger
Strobe Signal from Camera (available only on solder pad)
Pixel Data
Pixel Data
Pixel Data
Pixel Data
Camera IO Power Supply
Page | 18
Hardware User Manual - Argos2D - A10x
Pin No.
20
21
22
23
24
25
26
27
28
29
30
Signal Name
GND
PPI0.D4
PPI0.D5
PPI0.D6
PPI0.D7
GND
PPI0.D8
PPI0.D9
PPI0.D10
PPI0.D11
PF44
Last change: 9 April 2013
Version 1.1
Type
PWR
I
I
I
I
PWR
I
I
I
I
O
Description
Power Ground
Pixel Data
Pixel Data
Pixel Data
Pixel Data
Power Ground
Pixel Data
Pixel Data
Pixel Data
Pixel Data
Output Enable (Active Low)
Table 7.3: ISM connector g(X9)
7.2.8
µSD-Card holder h(X7)
The SDHC-Card signals are directly connected to the SD Port of the CM-i.MX53. A Micro SD-Card
connector mounted on the top side of the board supports µSD cards.
7.2.9
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
JTAG connector i(X12)
Signal Name
JTAG.REF
JTAG.PWR
JTAG.nTRST
GND
JTAG.TDI
GND
JTAG.TMS
GND
JTAG.TCK
GND
10k PD
GND
JTAG.TDO
GND
CTRL.nRESET
GND
JTAG.nDE
GND
10k PD
GND
Type
PWR
PWR
I 10k PU
PWR
I 10k PU
PWR
I 10k PU
PWR
I 10k PD
PWR
PWR
O 10k PU
PWR
I
PWR
I 10k PU
PWR
PWR
Description
2V8 Reference Voltage
3V3 Supply if S1.4 is on
JTAG Test Reset
Power Ground
JTAG Test Data Input
Power Ground
JTAG Test Mode Select
Power Ground
JTAG Test Clock
Power Ground
10k Pull Down
Power Ground
JTAG Test Data Output
Power Ground
Global Reset
Power Ground
JTAG Debug
Power Ground
10k Pull Down
Power Ground
Table 7.4: JTAG connector i(X12)
7.2.10 I/O extender connector j(X11)
Pin No.
1
2
3
4
5
6
Signal Name
UART1.RXD
I2C3.SDA
UART1.TXD
I2C3.SCL
GND
GND
© Bluetechnix 2013
Type
I
I/O 3k PU
O
O 3k PU
PWR
PWR
Description
UART1 Receive Data
I2C Data
UART1 Transmit Data
I2C Clock
Power Ground
Power Ground
Page | 19
Hardware User Manual - Argos2D - A10x
Pin No.
7
8
9
10
11
12
13
14
15
16
Signal Name
P_SW4_3V3
P_SW4_3V3
UART2.RXD
CAN1.RXD
UART2.TXD
CAN1.TXD
ECSPI2.SCLK
ECSPI2.MISO
ECSPI2.SS0
ECSPI2.MOSI
Last change: 9 April 2013
Version 1.1
Type
PWR
PWR
I 10k PU
I
O
O
O
I
O
O
Description
3.3V
3.3V
UART2 Receive Data
CAN Receive Data
UART2 Transmit Data
CAN Transmit Data
SPI CLK
SPI MISO
SPI Select0
SPI MOSI
Table 7.5: I/O extender connector j(X11)
7.2.11 RTC-battery holder k(G1)
There is also a possibility to add a 12mm coin cell to keep the RTC running. The Argos2D – A10x is delivered
only with a coin cell holder but without a battery.
7.2.12 Reset button l(S2)
The push buttons perform a reset.
7.2.13 Boot mode switch m(S1)
To set the right boot mode for the CM-i.MX53, only the switches 1, 2 and 3 are used.
Switch Setting
1 2 3 4
1 2 3 4
1 2 3 4
On
Off
Boot Description
Boot from SPI NOR flash
On
Off
Boot from SD card
On
Off
USB/UART boot mode
Some JTAG debuggers, like the PEEDI JTAG, short pins #1 and #2 (VREF and VSUPPLY) of the 20-pin ARM
JTAG header (X12). On the Argos®2D A100, these pins are connected to different voltages (2V8 vs. 3V3) and
must not be shortened. If your JTAG device/connector shorts pins #1 and #2, the following switch setting
must be done on Argos®2. It disconnects 3V3 from JTAG pin #2 (VSUPPLY).
Switch Setting
1 2 3 4
1 2 3 4
On
Off
On
Off
© Bluetechnix 2013
Description
Disconnect 3V3 from JTAG pin #2 (VSUPPLY)
Connect 3V3 to VSUPPLY
Page | 20
Hardware User Manual - Argos2D - A10x
7.2.14 Core Module connectors n(X1, X2, X3)
Last change: 9 April 2013
Version 1.1
The three connectors connecting the CM-i.MX53 Module, for more information take a look into the CMi.MX53 Hardware User Manual.
© Bluetechnix 2013
Page | 21
Hardware User Manual - Argos2D - A10x
7.3
Last change: 9 April 2013
Version 1.1
Mechanical Outline
57
All dimensions are given in mm.
57
143
55
5
Figure 7.1: Mechanical outline
7.4
7.4.1
Support
General Support
General support for products can be found at Bluetechnix’ support site https://support.bluetechnix.at/wiki
7.4.2
Board Support Packages
Board support packages and software downloads are for registered customers only
https://support.bluetechnix.at/wiki/Argos%C2%AE2D_A100_Camera.
7.4.3
i.MX Freescale Software Support
https://community.freescale.com/community/imx
7.4.3.1
Upcoming Products and Software Releases
Keep up to date with all product changes, releases and software updates of Bluetechnix at
http://www.bluetechnix.com.
© Bluetechnix 2013
Page | 22
Hardware User Manual - Argos2D - A10x
7.5
7.5.1
Dependability
Last change: 9 April 2013
Version 1.1
MTBF
Please keep in mind that a part stress analysis would be the only way to obtain significant failure rate results,
because MTBF numbers just represent a statistical approximation of how long a set of devices should last
before failure. Nevertheless, we can calculate an MTBF of the Core Module using the bill of material. We take
all the components into account. The PCB and solder connections are excluded from this estimation. For
test conditions we assume an ambient temperature of 30°C of all Core Module components except the
Blackfin® processor (80°C) and the memories (70°C). We use the MTBF Calculator from ALD
(http://www.aldservice.com/) and use the reliability prediction MIL-217F2 Part Stress standard. Please get in
touch with Bluetechnix ([email protected]) if you are interested in the MTBF result.
© Bluetechnix 2013
Page | 23
Hardware User Manual - Argos2D - A10x
8
Last change: 9 April 2013
Version 1.1
Product History
8.1
8.1.1
Version Information
Argos2D – A100 (150-1001-1)
Version
1.0.0
Component
ISM
CM
CB
Type
ISM-MT9M131-Color (100-3202-2)
CM-i.MX53-C-C-Q24S1024F4N2048 (100-1471-2)
eCAM-CM-i.MX53 Carrier Board (100-4122-1)
Table 8.1: Overview Argos2D – A100 product changes
8.1.2
Argos2D – A101 (150-1002-1)
Version
1.0.0
Component
ISM
CM
CB
Type
ISM-MT9M025-Mono (100-3200-2)
CM-i.MX53-C-C-Q24S1024F4N2048 (100-1471-2)
eCAM-CM-i.MX53 Carrier Board (100-4122-1)
Table 8.2: Overview Argos2D – A101 product changes
8.1.3
Argos2D – A102 (150-1003-1)
Version
1.0.0
Component
ISM
CM
CB
Type
ISM-MT9M025-Color (100-3206-2)
CM-i.MX53-C-C-Q24S1024F4N2048 (100-1471-2)
eCAM-CM-i.MX53 Carrier Board (100-4122-1)
Table 8.3: Overview Argos2D – A102 product changes
8.1.4
Argos2D – A103 (150-1004-1)
Version
1.0.0
Component
ISM
CM
CB
Type
ISM-MT9P031-Mono (100-3210-2)
CM-i.MX53-C-C-Q24S1024F4N2048 (100-1471-2)
eCAM-CM-i.MX53 Carrier Board (100-4122-1)
Table 8.4: Overview Argos2D – A103 product changes
8.1.5
Argos2D – A104 (150-1005-1)
Version
1.0.0
Component
ISM
CM
CB
Type
ISM-MT9P031-Color (100-3204-2)
CM-i.MX53-C-C-Q24S1024F4N2048 (100-1471-2)
eCAM-CM-i.MX53 Carrier Board (100-4122-1)
Table 8.5: Overview Argos2D – A104 product changes
8.2
Anomalies
Version
Date
© Bluetechnix 2013
Description
Page | 24
Hardware User Manual - Argos2D - A10x
Version
V1.0.0
Date
2013 02 06
Last change: 9 April 2013
Version 1.1
Description
No anomalies reported yet.
Table 8.6 – Product anomalies
8.3
Document Revision History
Version
1
Date
2013 02 06
Document Revision
First release V1.0 of the Document
Table 8.7: Revision history
© Bluetechnix 2013
Page | 25
Hardware User Manual - Argos2D - A10x
9
Last change: 9 April 2013
Version 1.1
Index
B
I
Board Support Packages · 22
Boot mode switch · 20
Interfaces & Connectors · 8
C
Connector and Interface Description · 18
E
M
Maximum Ratings · 17
MTBF
Mean Time Between Failure · 23
O
ESD
Electro Static Discharge · 17
Operating Conditions · 17
G
S
Getting Started · 15
Software Installation · 9
System Architecture · 6
H
Hardware Installation · 10
© Bluetechnix 2013
Page | 26