Austin AS4DDR32M72-10/ET 32mx72 ddr sdram integrated plastic encapsulated microcircuit Datasheet

i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
32Mx72 DDR SDRAM
iNTEGRATED Plastic Encapsulated Microcircuit
FEATURES
BENEFITS
„ DDR SDRAM Data Rate = 200, 250, 266, 333Mbps
„ Package:
„ 40% SPACE SAVINGS
„ Reduced part count
„ Reduced I/O count
•
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
219 Plastic Ball Grid Array (PBGA), 32 x 25mm
2.5V ±0.2V core power supply
2.5V I/O (SSTL_2 compatible)
Differential clock inputs (CLK and CLK#)
Commands entered on each positive CLK edge
Internal pipelined double-data-rate (DDR)
architecture; two data accesses per clock cycle
Programmable Burst length: 2,4 or 8
Bidirectional data strobe (DQS) transmitted/received
with data, i.e., source-synchronous data capture
(one per byte)
DQS edge-aligned with data for READs; center-aligned
with data for WRITEs
DLL to align DQ and DQS transitions with CLK
Four internal banks for concurrent operation
Two data mask (DM) pins for masking write data
Programmable IOL/IOH option
Auto precharge option
Auto Refresh and Self Refresh Modes
Industrial, Enhanced and Military Temperature
Ranges
Organized as 32M x 72/80
Weight: AS4DDR32M72PBG </= 3.10 grams typical
•
34% I/O Reduction
„ Reduced trace lengths for lower parasitic
capacitance
„ Suitable for hi-reliability applications
„ Laminate interposer for optimum TCE match
ConfigurationAddressing
Parameter
Configuration
RefreshCount
RowAddress
BankAddress
ColumnAddress
32Megx72
8Megx16x4Banks
8K
8K(A0ͲA12)
4(BA0ͲBA1)
1K(A0ͲA9)
* This product and or it’s specifications is subject to change without notice.
Monolithic Solution
O
P
T
I
O
N
S
11.9
11.9
11.9
11.9
Integrated MCP Solution
11.9
25
22.3
S
A
V
I
N
G
S
32
Area
I/O
Count
AS4DDR32M72PBG
Rev. 1.2 06/09
5 x 265mm2 = 1328mm2 Plus
5 x 66 pins = 320 pins
800mm2
40+%
219 Balls
34 %
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
1
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
SDRAM-DDR PINOUT TOP VIEW
DQ0
DQ14
DQ15
VSS
VSS
A9
A10
A11
A8
VCCQ
VCCQ
DQ16
DQ17
DQ31
VSS
DQ1
DQ2
DQ12
DQ13
VSS
VSS
A0
A7
A6
A1
VCC
VCC
DQ18
DQ19
DQ29
DQ30
DQ3
DQ4
DQ10
DQ11
VCC
VCC
A2
A5
A4
A3
VSS
VSS
DQ20
DQ21
DQ27
DQ28
DQ6
DQ5
DQ8
DQ9
VCCQ
VSSQ
A12
DNU
DNU
DNU
VSS
VSS
DQ22
DQ23
DQ26
DQ25
DQ7
DQML0
VCC
BA0
BA1
VREF
DQML1
VSS
NC
DQ24
CA S0\
WE0\
VCC
CLK0
DQSL3
RAS1\
WE1\
VSS
DQMH1
CLK1
CS0\
RAS0\
VCC
CKE0
CLKO\
CAS1\
CS1\
VSS
CLK1\
CKE1
VSS
VSS
VCC
VCCQ
VSS
VCC
VSS
VSS
VCCQ
VCC
VSS
VSS
VCC
VCCQ
VSS
VCC
VSS
VSS
VCCQ
VCC
CLK3\
CKE3
VCC
CS3\
DQSL4
CLK2\
CKE2
VSS
RAS2\
CS2\
NC
CLK3
VCC
CAS3\
RAS3\
DQSL2
CLK2
VSS
WE2\
CAS2\
DQ56 DQMH3
VCC
WE3\
DQML3
CS4\
DQMH2
VSS
DQML2
DQ39
DQ57
DQ58
DQ55
DQ54
DQSH4 CLK4\
DQ40
DQ37
DQ38
DQ60
DQ59
DQ53
DQ52
VSS
DQ62
DQ61
DQ51
DQ50
VSS
DQ63
DQ49
DQ48
Ground
AS4DDR32M72PBG
Rev. 1.2 06/09
DQMH0 DQSH3 DQSL0 DQSH0
CKE4 DQMH4
DQSL1 DQSH1
CLK4
CAS4\
WE4\
RAS4\
DQ73
DQ72
DQ71
DQ70
DQML4 DQSH2\ DQ41
VSS
DQ75
DQ74
DQ69
DQ68
VCC
VCC
DQ43
DQ42
DQ36
DQ35
VCC
VCC
DQ77
DQ76
DQ67
DQ66
VSS
VSS
DQ45
DQ44
DQ34
DQ33
VCCQ
VCCQ
DQ79
DQ78
DQ65
DQ64
VSS
VSS
DQ47
DQ46
DQ32
VCC
Array Power
D/Q Power
Address
CNTRL
Address/DNU
UNPOPULATED
Data IO
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
2
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
FUNCTIONAL BLOCK DIAGRAM
DQ0-15
DQ32-47
CLK0
CLK0\
CKE0
CS0\
WE0\
RAS0\
CAS0\
DQML0
DQMH0
DQSL0
DQSH0
BA0
BA1
CLK2
CLK2\
CKE2
CS2\
WE2\
RAS2\
CAS1\
DQML2
DQMH2
DQSL2
DQSH2
DDR
SDRAM
X16
2.5v Core
2.5v IO
SSTL-2
DDR
SDRAM
X16
2.5v Core
2.5v IO
SSTL-2
ADDR
VRef
VCC
VCCQ
VSS
CLK1
CLK1\
CKE1
CS1\
WE1\
RAS1\
CAS1\
DQML1
DQMH1
DQSL1
DQSH1
DQ1631
AS4DDR32M72PBG
Rev. 1.2 06/09
DDR
SDRAM
X16
2.5v Core
2.5v IO
SSTL-2
CLK3
CLK3\
CKE3
CS3\
WE3\
RAS3\
CAS3\
DQML3
DQMH3
DQSL3
DQSH3
DQ48-63
DDR
SDRAM
X16
2.5v Core
2.5v IO
SSTL-2
CLK4
CLK4\
CKE4
CS4\
WE4\
RAS4\
CAS4\
DQML4
DQMH4
DQSL4
DQSH4
DQ64-79
DDR
SDRAM
X16
2.5v Core
2.5v IO
SSTL-2
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
3
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
PIN DEFINITIONS / FUNCTIONAL DESCRIPTION
BGA Locations
SYMBOL
F4, F16, G5, G15, K1, K12,
CKx, CKx\
L2, L13, N6, M8
G4, G16, K2, K13, M6
G1, G13, K4, K16, M12
DESCRIPTION
Clock: CKx and CKx\ are differential clock inputs. All address and control input signals
are sampled on the crossing of the positive edge of CKx and negative edge of CKx\.
Output data (DQ's and DQS) is referenced to the crossings of the differential clock
inputs.
CKEx
Clock Enable: CKE controls the clock inputs. CKE high enables, CKE Low disables
the clock input pins. Driving CKE Low provides PRECHARGE POWER-DOWN. CKE
is synchronous for POWER-DOWN entry and exit, and for SELF REFRESH entry CKE
is Asynchronous for SELF REFRESH exit and for disabling the outputs. CKE must be
maintained HIGH throughout read and write accesses. Input buffers are disabled
during POWER-DOWN Input buffers are disabled during SELF REFRESH. CKE is an
SSTL-2 input but will detect an LVCMOS LOW level after VCC is applied
CSx\
Chip Select: CSx\ enables the COMMAND register(s) of each of the five (5) contained
words. All commands are masked with CSx\ is registered HIGH. CSx\ provides for
external bank selection on systems with multiple banks. CSx\ is considered part of the
COMMAND CODE.
F4, F16, G5, G15, K1, K12, RASx\, CASx\,
L2, L13, N7, M9
Wex\
Command Inputs: RASx, CASx and Wex\ define the command being entered.
G4, G16, K2, K14, M7
Input Data Mask: DM is an input mask signal for write data. Input data is masked when
DQMLx, DQMHx DQMLx or Hx is sampled HIGH at time of a WRITE access. DM is sampled on both
edges of DQSLx and DQSHx.
E8, E9
BA0, BA1
A7, A8, A9, A10, B7, B8,
B9, B10, C7, C8. C9, C10, A0-11, A12
D7
A2, A3, A4, A13, A14, B1,
B2, B3, B4, B13, B14, B15,
B16, C1, C2, C3, C4, C13,
C14, C15, C16, D1, D2, D3,
D4, D13, D14, D15, D16,
E1, E16, M1, M16, N1, N2, DQ0-79
N3, N4, N13, N14, N15,
N16, T2, T3, T4, T13, T14,
T15, N7, N8, N9, N10, P7,
P8, P9, P10, R7, R8, R9,
R10, T7, T8, T9, T10
E6, E7, E10, E11, F5, K5,
DQSLX, DQSHX
L12, N5, N12, E5
B11, B12, C5, C6, E3, F3,
G3, H3, H12, H16, J3, J12,
VCC
J16, K3, L3, M3, P11, P12,
R5, R6, T16
A11, A12, D5, D6, H4, H15,
VCCQ
J4, J15, T5, T6
Bank Address Inputs: BA0, BA1, define which bank an ACTIVE READ, WRITE or
PRECHARGE Command is being applied.
Address Input: Provide the row address for Active commands, and the column address
and auto precharge bit (A10) for READ / WRITE commands to select one location out
of the memory array in the respective bank. A10 sampled during a PRECHARGE
command determines whether the PRECHARGE applies to one bank or all banks.
The address inputs also provide the op-code during a MODE RESISTER SET
command.
Data I/O
Data Stobe: Output with read data, input with write data. DQS is edge-aligned with
read data, centered in write data. It is used to capture data
Core Power Supply
I/O Power Supply
A5, A6, A16, B5, B6, C11,
C12, D11, D12, E14, F14,
G14, H1, H2, H5, H13,
VSS
H14, J1, J2, J5, J13, J14,
K14, L14, P5, P6, R11.
R12, T1, T11, T12, M14
Ground (Digital)
E12
SSTL-2 Reference Voltage
AS4DDR32M72PBG
Rev. 1.2 06/09
VREF
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
4
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
GENERAL DESCRIPTION
FUNCTIONAL DESCRIPTION
The 2.4Gb DDR SDRAM MCM, is a high-speed CMOS,
dynamic random-access, memory using 5 chips containing
536,870,912 bits. Each chip is internally configured as a
quad-bank DRAM. Each of the chip’s 134,217,728-bit banks
is organized as 8,192 rows by 1024 columns by 32 bits.
Read and write accesses to the DDR SDRAM are burst
oriented; accesses start at a selected location and continue
for a programmed number of locations in a programmed
sequence. Accesses begin with the registration of an ACTIVE
command which is then followed by a READ or WRITE
command. The address bits registered coincident with the
ACTIVE command are used to select the bank and row to be
accessed (BA0 and BA1 select the bank, A0-12 select the
row). The address bits registered coincident with the READ
or WRITE command are used to select the starting column
location for the burst access.
The 256MB(2.4Gb) DDR SDRAM MCM uses a DDR
architecture to achieve high-speed operation. The double
data rate architecture is essentially a 2n-prefetch architecture
with an interface designed to transfer two data words per
clock cycle at the I/O pins. A single read or write access for
the 256MB DDR SDRAM effectively consists of a single 2nbit wide, one-clock-cycle data tansfer at the internal DRAM
core and two corresponding n-bit wide, one-half-clock-cycle
data transfers at the I/O pins.
Prior to normal operation, the SDRAM must be initialized. The
following sections provide detailed information covering
device initialization, register defi nition, command descriptions
and device operation.
A bidirectional data strobe (DQS) is transmitted externally,
along with data, for use in data capture at the receiver. DQS
is a strobe transmitted by the DDR SDRAM during READs
and by the memory contoller during WRITEs. DQS is
edgealigned with data for READs and center-aligned with
data for WRITEs. Each chip has two data strobes, one for
the lower byte and one for the upper byte.
INITIALIZATION
DDR SDRAMs must be powered up and initialized in a
predefined manner. Operational procedures other than those
specified may result in undefined operation. Power must first
be applied to VCC and VCCQ simultaneously, and then to VREF
(and to the system VTT). VTT must be applied after VCCQ to
avoid device latch-up, which may cause permanent damage
to the device. VREF can be applied any time after VCCQ but is
expected to be nominally coincident with VTT. Except for CKE,
inputs are not recognized as valid until after VREF is applied.
CKE is an SSTL_2 input but will detect an LVCMOS LOW level
after VCC is applied. Maintaining an LVCMOS LOW level on
CKE during powerup is required to ensure that the DQ and
DQS outputs will be in the High-Z state, where they will remain
until driven in normal operation (by a read access). After all
power supply and reference voltages are stable, and the clock
is stable, the DDR SDRAM requires a 200µs delay prior to
applying an executable command.
The 256MB DDR SDRAM operates from a differential clock
(CLK and CLK#); the crossing of CLK going HIGH and CLK#
going LOW will be referred to as the positive edge of CLK.
Commands (address and control signals) are registered at
every positive edge of CLK. Input data is registered on both
edges of DQS, and output data is referenced to both edges
of DQS, as well as to both edges of CLK.
Read and write accesses to the DDR SDRAM are burst
oriented; accesses start at a selected location and continue
for a programmed number of locations in a programmed
sequence. Accesses begin with the registration of an ACTIVE
command, which is then followed by a READ or WRITE
command. The address bits registered coincident with the
ACTIVE command are used to select the bank and row to be
accessed. The address bits registered coincident with the
READ or WRITE command are used to select the bank and
the starting column location for the burst access.
Once the 200µs delay has been satisfied, a DESELECT or
NOP command should be applied, and CKE should be
brought HIGH. Following the NOP command, a PRECHARGE
ALL command should be applied. Next a LOAD MODE
REGISTER command should be issued for the extended
mode register (BA1 LOW and BA0 HIGH) to enable the DLL,
followed by another LOAD MODE REGISTER command to
the mode register (BA0/ BA1 both LOW) to reset the DLL and
to program the operating parameters. Two-hundred clock
cycles are required between the DLL reset and any READ
command. A PRECHARGE ALL command should then be
applied, placing the device in the all banks idle state.
The DDR SDRAM provides for programmable READ or
WRITE burst lengths of 2, 4, or 8 locations. An auto precharge
function may be enabled to provide a selftimed row
precharge that is initiated at the end of the burst access.
The pipelined, multibank architecture of DDR SDRAMs allows
for concurrent operation, thereby providing high effective
bandwidth by hiding row precharge and activation time.
Once in the idle state, two AUTO REFRESH cycles must be
performed (tRFC must be satisfi ed.) Additionally, a LOAD
MODE REGISTER command for the mode register with the
reset DLL bit deactivated (i.e., to program operating
parameters without resetting the DLL) is required. Following
these requirements, the DDR SDRAM is ready for normal
operation.
An auto refresh mode is provided, along with a powersaving
power-down mode.
AS4DDR32M72PBG
Rev. 1.2 06/09
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
5
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
TABLE 1 - BURST DEFINITION
REGISTER DEFINITION
MODE REGISTER
Burst
Length
The Mode Register is used to define the specific mode of
operation of the DDR SDRAM. This definition includes the
selection of a burst length, a burst type, a CAS latency, and
an operating mode, as shown in Figure 3. The Mode Register
is programmed via the MODE REGISTER SET command
(with BA0 = 0 and BA1 = 0) and will retain the stored
information until it is programmed again or the device loses
power. (Except for bit A8 which is self clearing).
2
4
Reprogramming the mode register will not alter the contents
of the memory, provided it is performed correctly. The Mode
Register must be loaded (reloaded) when all banks are idle
and no bursts are in progress, and the controller must wait
the specified time before initiating the subsequent operation.
Violating either of these requirements will result in
unspecified operation. Mode register bits A0-A2 specify the
burst length, A3 specifies the type of burst (sequential or
interleaved), A4-A6 specify the CAS latency, and A7-A12
specify the operating mode.
8
Order of Accesses Within a Burst
Type = Sequential
Type = Interleaved
0-1
1-0
0-1
1-0
0-1-2-3
1-2-3-0
2-3-0-1
3-0-1-2
0-1-2-3
1-0-3-2
2-3-0-1
3-2-1-0
0-1-2-3-4-5-6-7
1-2-3-4-5-6-7-0
2-3-4-5-6-7-0-1
3-4-5-6-7-0-1-2
4-5-6-7-0-1-2-3
5-6-7-0-1-2-3-4
6-7-0-1-2-3-4-5
7-0-1-2-3-4-5-6
0-1-2-3-4-5-6-7
1-0-3-2-5-4-7-6
2-3-0-1-6-7-4-5
3-2-1-0-7-6-5-4
4-5-6-7-0-1-2-3
5-4-7-6-1-0-3-2
6-7-4-5-2-3-0-1
7-6-5-4-3-2-1-0
NOTES:
1. For a burst length of two, A1-Ai select two-data-element block;
A0 selects the starting column within the block.
2. For a burst length of four, A2-Ai select four-data-element block;
A0-1 select the starting column within the block.
3. For a burst length of eight, A3-Ai select eight-data-element block;
A0-2 select the starting column within the block.
4. Whenever a boundary of the block is reached within a given
sequence above, the following access wraps within the block.
BURST LENGTH
Read and write accesses to the DDR SDRAM are burst
oriented, with the burst length being programmable, as
shown in Figure 3. The burst length determines the maximum
number of column locations that can be accessed for a given
READ or WRITE command. Burst lengths of 2, 4 or 8
locations are available for both the sequential and the
interleaved burst types.
READ LATENCY
The READ latency is the delay, in clock cycles, between the
registration of a READ command and the availability of the
first bit of output data. The latency can be set to 2 or 2.5
clocks.
Reserved states should not be used, as unknown operation
or incompatibility with future versions may result.
If a READ command is registered at clock edge n, and the
latency is m clocks, the data will be available by clock edge
n+m. Table 2 below indicates the operating frequencies at
which each CAS latency setting can be used.
When a READ or WRITE command is issued, a block of
columns equal to the burst length is effectively selected. All
accesses for that burst take place within this block, meaning
that the burst will wrap within the block if a boundary is
reached. The block is uniquely selected by A1-Ai when the
burst length is set to two; by A2-Ai when the burst length is
set to four (where Ai is the most significant column address
for a given configuration); and by A3-Ai when the burst length
is set to eight. The remaining (least significant) address
bit(s) is (are) used to select the starting location within the
block. The programmed burst length applies to both READ
and WRITE bursts.
Reserved states should not be used as unknown operation
or incompatibility with future versions may result.
TABLE 2 - CAS LATENCY
SPEED
-10
-8
-75
-6
BURST TYPE
Accesses within a given burst may be programmed to be
either sequential or interleaved; this is referred to as the
burst type and is selected via bit M3. The ordering of accesses
within a burst is determined by the burst length, the burst
type and the starting column address, as shown in Table 1.
AS4DDR32M72PBG
Rev. 1.2 06/09
Starting Column
Address
A0
0
1
A1 A0
0
0
0
1
1
0
1
1
A2 A1 A0
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
ALLOWABLE OPERATING
FREQUENCY (MHz)
CAS
CAS
LATENCY=2 LATENCY=2.5
” 75
” 100
” 100
” 125
” 100
” 133
” 100
” 166
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
6
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
OPERATING MODE
The normal operating mode is selected by issuing a MODE
REGISTER SET command with bits A7-A12 each set to zero,
and bits A0-A6 set to the desired values. A DLL reset is initiated
by issuing a MODE REGISTER SET command with bits A7 and
A9-A12 each set to zero, bit A8 set to one, and bits A0-A6 set to
the desired values. Although not required, JEDEC specifications
recommend when a LOAD MODE REGISTER command is
issued to reset the DLL, it should always be followed by a
LOAD MODE REGISTER command to select normal operating
mode.
FIGURE 1 - MODE BURST DEFINITION
BA1
A12 A11 A10 A9
BA0
A8
A7
A6
A5
A3
A4
A2
A1
A0
Address Bus
Mode Register (Mx)
0*
0*
Operating Mode
CAS Latency
BT
Burst Length
* M14 and M13
(BA0 and BA1 must be
"0, 0" to select
the base mode register
(vs. the extended
mode register).
Burst Length
M2 M1 M0
All other combinations of values for A7-A12 are reserved for
future use and/or test modes. Test modes and reserved states
should not be used because unknown operation or
incompatibility with future versions may result.
M3 = 0
M3 = 1
0
0 0
0
0 1
2
2
0
1 0
4
4
Reserved
Reserved
0
1 1
8
8
1
0 0
Reserved
Reserved
1
0 1
Reserved
Reserved
1
1 0
Reserved
Reserved
1
1 1
Reserved
Reserved
EXTENDED MODE REGISTER
The extended mode register controls functions beyond those
controlled by the mode register; these additional functions are
DLL enable/disable, output drive strength, and QFC#. These
functions are controlled via the bits shown in Figure 3. The
extended mode register is programmed via the LOAD MODE
REGISTER command to the mode register (with BA0 = 1 and
BA1 = 0) and will retain the stored information until it is
programmed again or the device loses power. The enabling of
the DLL should always be followed by a LOAD MODE
REGISTER command to the mode register (BA0/BA1 both LOW)
to reset the DLL.
The extended mode register must be loaded when all banks
are idle and no bursts are in progress, and the controller must
wait the specified time before initiating any subsequent
operation. Violating either of these requirements could result
in unspecified operation.
AS4DDR32M72PBG
Rev. 1.2 06/09
Burst Type
M3
0
Sequential
1
Interleaved
M6 M5 M4
CAS Latency
0
0 0
Reserved
0
0 1
Reserved
0
1 0
2
0
1 1
Reserved
1
0 0
Reserved
1
0 1
Reserved
1
1 0
2.5
1
1 1
Reserved
M12
M11
M10
M9
M8
M7
M6-M0
0
0
0
0
0
0
Valid
Normal Operation
0
0
0
0
1
0
Valid
Normal Operation/Reset DLL
-
-
-
-
-
-
-
Operating Mode
All other states reserved
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
7
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
FIGURE 2 - CAS LATENCY
T0
T1
T2
READ
NOP
NOP
FIGURE 3 - EXTENDED MODE REGISTER
DEFINITION
T2n
T3
T3n
BA1 BA0 A12 A11 A10 A9
CLK
A8
A7
A6
A5
A3
A4
A2
A 1 A0
Address Bus
CLK
COMMAND
NOP
11
01
CL = 2
QFC# DS
Operating Mode
DLL
Extended Mode
Register (Ex)
DQS
DQ
T0
T1
T2
READ
NOP
NOP
T2n
T3
T3n
E0
DLL
0
Enable
1
Disable
CLK
E1
CLK
COMMAND
NOP
CL = 2.5
E22
DQS
DQ
DATA
TRANSITIONING DATA
Normal
1
Reduced
QFC# Function
0
Disabled
-
Reserved
E8
E7
E6
E5
E4
E3
E2, E1, E0
Operating Mode
0
0
0
0
0
0
0
0
0
0
Valid
Reserved
-
-
-
-
-
-
-
-
-
-
-
Reserved
E12 E11 E10 E9
Burst Length = 4 in the cases shown
Shown with nominal tAC and nominal tDSDQ
Drive Strength
0
1. E14 and E13 must be "0, 1" to select the Extended Mode Register (vs. the base Mode Register)
2. The QFE# function is not supported.
DON'T CARE
OUTPUT DRIVE STRENGTH
NO OPERATION (NOP)
The normal full drive strength for all outputs are specified to
be SSTL2, Class II. The DDR SDRAM supports an option for
reduced drive. This option is intended for the support of the
lighter load and/or point-to-point environments. The selection
of the reduced drive strength will alter the DQs and DQSs
from SSTL2, Class II drive strength to a reduced drive strength,
which is approximately 54 percent of the SSTL2, Class II
drive strength.
The NO OPERATION (NOP) command is used to perform a
NOP to the selected DDR SDRAM (CS# is LOW). This
prevents unwanted commands from being registered during
idle or wait states. Operations already in progress are not
affected.
LOAD MODE REGISTER
The Mode Registers are loaded via inputs A0-12. The LOAD
MODE REGISTER command can only be issued when all
banks are idle, and a subsequent executable command
cannot be issued until tMRD is met.
DLL ENABLE/DISABLE
The DLL must be enabled for normal operation. DLL enable
is required during power-up initialization and upon returning
to normal operation after having disabled the DLL for the
purpose of debug or evaluation. (When the device exits self
refresh mode, the DLL is enabled automatically.) Any time
the DLL is enabled, 200 clock cycles must occur before a
READ command can be issued.
ACTIVE
The ACTIVE command is used to open (or activate) a row in
a particular bank for a subsequent access. The value on
the BA0, BA1 inputs selects the bank, and the address
provided on inputs A0-12 selects the row. This row remains
active (or open) for accesses until a PRECHARGE
command is issued to that bank. A PRECHARGE command
must be issued before opening a different row in the same
bank.
COMMANDS
The Truth Table provides a quick reference of available
commands. This is followed by a written description of each
command.
DESELECT
The DESELECT function (CS# HiGH) prevents new
commands from being executed by the DDR SDRAM. The
SDRAM is effectively deselected. Operations already in
progress are not affected.
AS4DDR32M72PBG
Rev. 1.2 06/09
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
8
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
TRUTH TABLE - COMMANDS (NOTE 1)
NAME (FUNCTION)
DESELECT (NOP)(9)
NO OPERATION (NOP) (9)
ACTIVE (Select bank and activate row) (3)
READ (Select bank and column, and start READ burst) (4)
WRITE (Select bank and column, and start WRITE burst) (4)
BURST TERMINATE (8)
PRECHARGE (Deactivate row in bank or banks) (5)
AUTO REFRESH or SELF REFRESH (Enter self refresh mode) (6,7)
LOAD MODE REGISTER (2)
CS#
H
L
L
L
L
L
L
L
L
RAS#
X
H
L
H
H
H
L
L
L
CAS#
X
H
H
L
L
H
H
L
L
WE#
X
H
H
H
L
L
L
H
L
ADDR
X
X
Bank/Row
Bank/Col
Bank/Col
X
Code
X
Op-Code
TRUTH TABLE - DM OPERATION
NAME (FUNCTION)
WRITE ENABLE (10)
WRITE INHIBIT (10)
DM
L
H
NOTES:
1 . CKE is HIGH for all commands shown except SELF REFRESH.
2 . A0-12 define the op-code to be written to the selected Mode Register.
BA0, BA1 select either the mode register (0, 0) or the extended mode
register (1, 0).
3. A0-12 provide row address, and BA0, BA1 provide bank address.
4. A0-8 provide column address; A10 HIGH enables the auto precharge
feature (non-persistent), while A10 LOW disables the auto precharge
feature; BA0, BA1 provide bank address.
5. A10 LOW: BA0, BA1 determine the bank being precharged. A10 HIGH:
All banks precharged and BA0, BA1 are “Don’t Care.”
DQs
Valid
X
6 . This command is AUTO REFRESH if CKE is HIGH; SELF REFRESH if
CKE is LOW.
7 . Internal refresh counter controls row addressing; all inputs and I/Os are
“Don’t Care” except for CKE.
8. Applies only to read bursts with auto precharge disabled; this command
is undefined (and should not be used) for READ bursts with auto
precharge enabled and for WRITE bursts.
9 . DESELECT and NOP are functionally interchangeable.
10. Used to mask write data; provided coincident with the corresponding
data.
READ
PRECHARGE
The READ command is used to initiate a burst read
access to an active row. The value on the BA0, BA1 inputs
selects the bank, and the address provided on inputs A09 selects the starting column location. The value on input
A10 determines whether or not AUTO PRECHARGE is
used. If AUTO PRECHARGE is selected, the row being
accessed will be precharged at the end of the READ burst;
if AUTO PRECHARGE is not selected, the row will remain
open for subsequent accesses.
The PRECHARGE command is used to deactivate the open
row in a particular bank or the open row in all banks. The
bank(s) will be available for a subsequent row access a
specified time (tRP) after the PRECHARGE command is
issued. Except in the case of concurrent auto precharge,
where a READ or WRITE command to a different bank is
allowed as long as it does not interrupt the data transfer in
the current bank and does not violate any other timing
parameters. Input A10 determines whether one or all banks
are to be precharged, and in the case where only one bank
is to be precharged, inputs BA0, BA1 select the bank.
Otherwise BA0, BA1 are treated as “Don’t Care.” Once a
bank has been precharged, it is in the idle state and must
be activated prior to any READ or WRITE commands being
issued to that bank. A PRECHARGE command will be
treated as a NOP if there is no open row in that bank (idle
state), or if the previously open row is already in the process
of precharging.
WRITE
The WRITE command is used to initiate a burst write
access to an active row. The value on the BA0, BA1 inputs
selects the bank, and the address provided on inputs A09 selects the starting column location. The value on input
A10 determines whether or not AUTO PRECHARGE is
used. If AUTO PRECHARGE is selected, the row being
accessed will be precharged at the end of the WRITE
burst; if AUTO PRECHARGE is not selected, the row will
remain open for subsequent accesses. Input data
appearing on the D/Qs iswritten to the memory array
subject to the DQM input logic level appearing coincident
with the data. If a given DQM signal is registered LOW, the
corresponding data will be written to memory; if the DQM
signal is registered HIGH, the corresponding data inputs
will be ignored, and a WRITE will not be executed to that
byte/column location.
AS4DDR32M72PBG
Rev. 1.2 06/09
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
9
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
AUTO PRECHARGE
Although not a JEDEC requirement, to provide for future
functionality features, CKE must be active (High) during the
AUTO REFRESH period. The AUTO REFRESH period begins
when the AUTO REFRESH command is registered and ends
tRFC later.
AUTO PRECHARGE is a feature which performs the same
individual-bank PRECHARGE function described above, but
without requiring an explicit command. This is accomplished
by using A10 to enable AUTO PRECHARGE in conjunction
with a specific READ or WRITE command. A precharge of
the bank/row that is addressed with the READ or WRITE
command is automatically performed upon completion of
the READ or WRITE burst. AUTO PRECHARGE is
nonpersistent in that it is either enabled or disabled for each
individual READ or WRITE command. The device supports
concurrent auto precharge if the command to the other bank
does not interrupt the data transfer to the current bank.
SELF REFRESH*
The SELF REFRESH command can be used to retain data
in the DDR SDRAM, even if the rest of the system is powered
down. When in the self refresh mode, the DDR SDRAM retains
data without external clocking. The SELF REFRESH
command is initiated like an AUTO REFRESH command
except CKE is disabled (LOW). The DLL is automatically
disabled upon entering SELF REFRESH and is automatically
enabled upon exiting SELF REFRESH (200 clock cycles must
then occur before a READ command can be issued). Input
signals except CKE are “Don’t Care” during SELF REFRESH.
The procedure for exiting self refresh requires a sequence
of commands. First, CLK must be stable prior to CKE going
back HIGH. Once CKE is HIGH, the DDR SDRAM must have
NOP commands issued for tXSNR, because time is required
for the completion of any internal refresh in progress. A
simple algorithm for meeting both refresh and DLL
requirements is to apply NOPs for 200 clock cycles before
applying any other command.
AUTO PRECHARGE ensures that the precharge is initiated
at the earliest valid stage within a burst. This “earliest valid
stage” is determined as if an explicit precharge command
was issued at the earliest possible time, without violating
tRAS (MIN).The user must not issue another command to the
same bank until the precharge time (tRP) is completed. This
is determined as if an explicit PRECHARGE command was
issued at the earliest possible time, without violating tRAS
(MIN).
BURST TERMINATE
* Self refresh available in commercial and industrial temperatures only.
The BURST TERMINATE command is used to truncate READ
bursts (with auto precharge disabled). The most recently
registered READ command prior to the BURST TERMINATE
command will be truncated. The open page which the READ
burst was terminated from remains open.
AUTO REFRESH
AUTO REFRESH is used during normal operation of the
DDR SDRAM and is analogous to CAS#-BEFORE-RAS#
(CBR) REFRESH in conventional DRAMs. This command is
nonpersistent, so it must be issued each time a refresh is
required.
The addressing is generated by the internal refresh
controller. This makes the address bits “Don’t Care” during
an AUTO REFRESH command. Each DDR SDRAM requires
AUTO REFRESH cycles at an average interval of 7.8125µs
(maximum).
To allow for improved efficiency in scheduling and switching
between tasks, some flexibility in the absolute refresh interval
is provided. A maximum of eight AUTO REFRESH commands
can be posted to any given DDR SDRAM, meaning that the
maximum absolute interval between any AUTO REFRESH
command and the next AUTO REFRESH command is 9 x
7.8125µs (70.3µs). This maximum absolute interval is to
allow future support for DLL updates internal to the DDR
SDRAM to be restricted to AUTO REFRESH cycles, without
allowing excessive drift in tAC between updates.
AS4DDR32M72PBG
Rev. 1.2 06/09
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
10
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
ABSOLUTE MAXIMUM RATINGS
Parameter
Voltage on VCC, VCCQ Supply relative to VSS
-1 ot 3.6
Voltage on I/O pins relative to VSS
-1 ot 3.6
Unit
V
Operating Temperature TA (Mil)
-55 to +125
Operating Temperature TA (Ind)
-40 to +85
Storage Temperature, Plastic
-55 to +150
V
C
o
o
C
o
C
Note: Stress greater than those listed under "Absolute Maximum Ratings" may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions greater than those indicated in the
operational conditions for extended periods may affect reliability.
CAPACITANCE (NOTE 13)
Parameter
Input Capacitance: CLK
Addresses, BA0-1 Input Capacitance
Input Capacitance: All other input-only pins
Input/Output Capacitance: I/O's
AS4DDR32M72PBG
Rev. 1.2 06/09
Symbol
C11
CA
C12
Max
8
30
9
Unit
pF
pF
pF
C10
12
pF
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
11
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
DC ELECTRICAL CHARACTERISTICS AND OPERATING CONDITIONS (NOTES 1,6)
VCC, VCCQ = +2.5V ± 0.2V; -55oC ± 0.2V, -55oC TA +125oC
Parameter / Condition
Supply Voltage
Symbol
VCC
Min
2.3
Max
2.7
VCCQ
2.3
2.7
V
II
-2
2
µA
I/O Supply Voltage
Input Leakage Current: Any input 0V ” VIN ” VCC (All other pins not under test = 0V)
Input Leakage Address Current (All other pins not under test = 0V)
Output Leakage Current: I/O's are disabled; 0V ” VOUT ” VCC
Output Levels: Full drive option
High Current (VOUT = VCCQ - 0.373V, minimum VREF, minimum VTT)
Low Current (VOUT = 0.373V, maximum VREF, maximum VTT)
Output Levels: Reduced drive option
High Current (VOUT = VCCQ - 0.763V, minimum VREF, minimum VTT)
Low Current (VOUT = 0.763V, maximum VREF, maximum VTT)
Units
V
II
-10
10
µA
IOZ
-5
5
µA
IOH
-12
-
mA
IOL
12
-
mA
IOHR
-9
-
mA
IOLR
VREF
9
0.49 x VCCQ
0.51 x VCCQ
mA
I/O Reference Voltage (6)
I/O Termination Voltage (53)
VTT
VREF - 0.04
VREF + 0.04
V
V
AC INPUT OPERATING CONDITIONS (NOTES 1,6)14, 28, 40
VCC, VCCQ = +2.5V ± 0.2V; -55oC ± 0.2V, -55oC TA +125oC
Parameter / Condition
Input High (Logic 1) Voltage:
Symbol
Min
VIH (AC) VREF + 0.310
Input Low (Logic ) Voltage:
VIL (AC)
-
Max
Units
V
VREF - 0.310
V
ICC SPECIFICATIONS AND CONDITIONS (NOTES 1-5, 10, 12, 14)
VCC, VCCQ = +2.5V ± 0.2V; -55oC ± 0.2V, -55oC TA +125oC
Max
333, 266
Symbol 250 Mbps
Parameter / Condition
200 Mbps Units
OPERATING CURRENT: One bank, Active-Precharge; tRC = tRC (MIN); tCK = tCK (MIN); DQ, DM, and DQS inputs changing once per clock cycle;
Address and control inputs changing once every two clock cycles; (22, 48)
ICC0
625
600
mA
OPERATING CURRENT: One bank, Active-Read- Precharge; Burst=2; tRC = tRC (MIN); tCK = tCK (MIN); IOUT = 0mA; Address and control inputs
changing once every two clock cycles; (22, 48)
PRECHARGE POWER-DOWN STANDBY CURRENT: All banks idle; Power-down mode; tCK=tCK (MIN); CKE=LOW; (23, 32. 50)
ICC1
ICC2P
850
20
775
20
mA
mA
IDLE STANDBY CURRENT: CS#=HIGH, All banks idle; tCK=tCK (MIN); CKE=HIGH; Address and other control inputs changing once per clock
cycle. VIN=VREF for DQ, DQS and DM (51)
ACTIVE POWER-DOWN STANDBY CURRENT: One bank active; Power-down mode; tCK=tCK (MIN); CKE=LOW (23, 32, 50)
ICC2F
ICC3P
225
150
225
150
mA
mA
ACTIVE STANDBY CURRENT: CS#=HIGH; CKE=HIGH; One bank; Active Precharge; tRC=tRAS (MAX); tCK=tCK (MIN); DQ, DM and DQS inputs
changin twicer per clock cycle; Address and other control inputs changing once per clock cycle (22)
ICC3N
250
250
mA
OPERATING CURRENT: Burst=2; Reads; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK=tCK
(MIN); IOUT=0mA (22,48)
ICC4R
925
925
mA
OPERATING CURRENT: Burst=2; Writes; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK=tCK
(MIN); DQ, DM and DQS inputs changin twice per clock cycle (22)
tREF=tRC (MIN) (27, 50)
AUTO REFRESH CURRENT
tREF=7.8125 µs (27, 50)
Standard (11)
SELF REFRESH CURRENT: CKE ” 0.2V
ICC4W
ICC5
ICC5A
ICC6
800
1225
30
20
800
1225
30
20
mA
mA
mA
mA
OPERATING CURRENT: Four bank interleaving DEADs (BL=4) with auto precharge, tRC=tRC (MIN); tCK=tCK (MIN); Addresses and control inputs
change only during Active READ or WRITE commands. (22, 49)
ICC7
2000
2000
mA
AS4DDR32M72PBG
Rev. 1.2 06/09
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
12
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
ELECTRICAL CHARACTERISTICS AND
CHARACTERISTICS (NOTES 1-5, 14-17, 33)
Parameter
Access window of DQs from CLK/CLK#
CLK high-level width (30)
CLK low-level width (30)
Clock cycle time
CL=2.5 (45, 52)
CL=2 (45, 52)
DQ and DM input hold time relative to DQS (26, 31)
DQ and DM input setup time relative to DQS (26,31)
DQ and DM input pulse with (for each input) (31)
Access window of DQS from CLK/CLK#
DQS input high pulse width
DQS input high pulse width
DQS-DQ skew, DQS to last valid, per group, per access (25,26)
Write command to first DQS latching transition
DQS falling edge to CLK rising - setup time
DQS falling edge to CLK rising - hold time
Half clock period (34)
Data-out high-impedance window from CLK/CLK# (18, 42)
Data-out low-impedance window from CLK/CLK# (18, 43)
Address and control input hold time (fast slew rate) (14)
Address and control input setup time (fast slew rate) (14)
Address and control input hold time (slow slew rate) (14)
Address and control input setup time (slow slew rate) (14)
LOAD MODE REGISTER command cycle time
DQ-DQS hold, DQS to first DQ to go non-valid, per access (25, 26)
Data hold skew factor
ACTIVE to PRECHARGE command (35)
ACTIVE to READ with Auto precharge command
ACTIVE to ACTIVE/AUTO REFRESH command period
AUTO REFRESH command period (50)
ACTIVE to READ or WRITE delay
PRECHARGE command period
DQS read preamble (42)
DQS read postamble
Active bank a to ACTIVE bank b command
DQS write preamble
DQS write preamble setup time (20,21)
DQS write postamble (19)
Write recovery time
Internal WRITE to READ command delay
Data valid output window (25)
REFRESH to REFRESH command interval (Commercial & Industrial temp
REFRESH to REFRESH command interval (Military temp only) (23)
Average periodic refresh interval (Commercial & Industrial temp only) (23)
Average periodic refresh interval (Military temp only) (23)
Terminating voltage delay to Vcc (53)
Exit SELF REFRESH to non-READ command
Exit SELF REFRESH to READ command
AS4DDR32M72PBG
Rev. 1.2 06/09
RECOMMENDED
Symbol
tAC
tCH
tCL
tCK (2.5)
tCK (2)
tDH
tDS
tDIPW
tDQSCK
tDQSH
tDQSL
tDQSQ
tDQSS
tDSS
tDSH
tHP
tHZ
tLZ
tIHF
tISF
tIHS
tISS
tMRD
tQH
tQHS
tRAS
tRAP
tRC
tRFC
tRCD
tRP
tRPRE
tRPST
tRRD
tWPRE
tWPRES
tWPST
tWR
tWTR
NA
tREFC
tREFC
tREFI
tREFI
tVTD
tXSNR
tXSRD
-6, 333 [266] Mbps
@CL=2.5 [CL=2]
Min
Max
-0.70
+0.70
0.45
0.55
0.45
0.55
6
13
7.5
13
0.45
0.45
1.75
-0.6
+0.6
0.35
0.35
0.45
0.75
1.25
0.2
0.2
tCH, tCL
+0.7
-0.7
0.75
0.75
0.8
0.8
12
tHP-tQHS
0.55
42
70,000
15
60
72
15
15
0.9
1.1
0.4
0.6
12
0.25
0
0.4
0.6
15
1
tQH - tDQSQ
70.3
35
7.8
3.9
0
75
200
AC
OPERATING
-75, 266 [250] Mbps
@CL=2.5 [CL=2]
Min
Max
-0.75
+0.75
0.45
0.55
0.45
0.55
7.5
13
8
13
0.5
0.5
1.75
-0.75
+0.75
0.35
0.35
0.5
0.75
1.25
0.2
0.2
tCH, tCL
+0.75
-0.75
0.9
0.9
1.0
1.0
15
tHP-tQHS
1
40
120,000
15
60
75
15
15
0.9
1.1
0.4
0.6
15
0.25
0
0.4
0.6
15
1
tQH - tDQSQ
70.3
35
7.8
3.9
0
75
200
Units
ns
tCK
tCK
ns
ns
ns
ns
ns
ns
tCK
tCK
ns
tCK
tCK
tCK
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tCK
tCK
ns
tCK
ns
tCK
ns
tCK
ns
µs
µs
µs
µs
ns
ns
tCK
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
13
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
ELECTRICAL CHARACTERISTICS AND
CHARACTERISTICS (NOTES 1-5, 14-17, 33)
Parameter
Access window of DQs from CLK/CLK#
CLK high-level width (30)
CLK low-level width (30)
Clock cycle time
CL=2.5 (45, 52)
CL=2 (45, 52)
DQ and DM input hold time relative to DQS (26, 31)
DQ and DM input setup time relative to DQS (26,31)
DQ and DM input pulse with (for each input) (31)
Access window of DQS from CLK/CLK#
DQS input high pulse width
DQS input high pulse width
DQS-DQ skew, DQS to last valid, per group, per access (25,26)
Write command to first DQS latching transition
DQS falling edge to CLK rising - setup time
DQS falling edge to CLK rising - hold time
Half clock period (34)
Data-out high-impedance window from CLK/CLK# (18, 42)
Data-out low-impedance window from CLK/CLK# (18, 43)
Address and control input hold time (fast slew rate) (14)
Address and control input setup time (fast slew rate) (14)
Address and control input hold time (slow slew rate) (14)
Address and control input setup time (slow slew rate) (14)
LOAD MODE REGISTER command cycle time
DQ-DQS hold, DQS to first DQ to go non-valid, per access (25, 26)
Data hold skew factor
ACTIVE to PRECHARGE command (35)
ACTIVE to READ with Auto precharge command
ACTIVE to ACTIVE/AUTO REFRESH command period
AUTO REFRESH command period (50)
ACTIVE to READ or WRITE delay
PRECHARGE command period
DQS read preamble (42)
DQS read postamble
Active bank a to ACTIVE bank b command
DQS write preamble
DQS write preamble setup time (20,21)
DQS write postamble (19)
Write recovery time
Internal WRITE to READ command delay
Data valid output window (25)
REFRESH to REFRESH command interval (Commercial & Industrial temp
REFRESH to REFRESH command interval (Military temp only) (23)
Average periodic refresh interval (Commercial & Industrial temp only) (23)
Average periodic refresh interval (Military temp only) (23)
Terminating voltage delay to Vcc (53)
Exit SELF REFRESH to non-READ command
Exit SELF REFRESH to READ command
AS4DDR32M72PBG
Rev. 1.2 06/09
RECOMMENDED
Symbol
tAC
tCH
tCL
tCK (2.5)
tCK (2)
tDH
tDS
tDIPW
tDQSCK
tDQSH
tDQSL
tDQSQ
tDQSS
tDSS
tDSH
tHP
tHZ
tLZ
tIHF
tISF
tIHS
tISS
tMRD
tQH
tQHS
tRAS
tRAP
tRC
tRFC
tRCD
tRP
tRPRE
tRPST
tRRD
tWPRE
tWPRES
tWPST
tWR
tWTR
NA
tREFC
tREFC
tREFI
tREFI
tVTD
tXSNR
tXSRD
-8, 250 [200] Mbps
@CL=2.5 [CL=2]
Min
Max
-0.8
+0.8
0.45
0.55
0.45
0.55
8
13
10
13
0.6
0.6
2
-0.8
+0.8
0.35
0.35
0.6
0.75
1.25
0.2
0.2
tCH, tCL
+0.8
-0.8
1.1
1.1
1.1
1.1
16
tHP-tQHS
1
40
120,000
20
70
80
20
20
0.9
1.1
0.4
0.6
15
0.25
0
0.4
0.6
15
1
tQH-tDQSQ
70.3
35
7.8
3.9
0
80
200
AC
OPERATING
-10, 200 [167] Mbps
@CL=2.5 [CL=2]
Min
Max
-0.8
+0.8
0.45
0.55
0.45
0.55
10
13
13
15
0.6
0.6
2
-0.8
+0.8
0.35
0.35
0.6
0.75
1.25
0.2
0.2
tCH, tCL
+0.8
-0.8
1.1
1.1
1.1
1.1
16
tHP-tQHS
1
40
120,000
20
70
80
20
20
0.9
1.1
0.4
0.6
15
0.25
0
0.4
0.6
15
1
tQH-tDQSQ
70.3
35
7.8
3.9
0
80
200
Units
ns
tCK
tCK
ns
ns
ns
ns
ns
ns
tCK
tCK
ns
tCK
tCK
tCK
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tCK
tCK
ns
tCK
ns
tCK
ns
tCK
ns
µs
µs
µs
µs
ns
ns
tCK
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
14
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
NOTES:
1. All voltages referenced to VSS.
2. Tests for AC timing, ICC, and electrical AC and DC characteristics may be
conducted at nominal reference/supply voltage levels, but the related
specifications and device operation are guaranteed for the full voltage
range specified.
3. Outputs measured with equivalent load:
VTT
50Ω
Reference
Point
30pF
Output
(VOUT)
4. AC timing and ICC tests may use a VIL-to-VIH swing of up to 1.5V in the test
environment, but input timing is still referenced to VREF (or to the crossing
point for CLK/CLK#), and parameter specifications are guaranteed for the
specified AC input levels under normal use conditions. The minimum slew
rate for the input signals used to test the device is 1V/ns in the range
between VIL(AC) and VIH(AC).
5. The AC and DC input level specifications are as defined in the SSTL_2
Standard (i.e., the receiver will effectively switch as a result of the signal
crossing the AC input level, and will remain in that state as long as the
signal does not ring back above [below] the DC input LOW [HIGH] level).
6. VREF is expected to equal VCCQ/2 of the transmitting device and to track
variations in the DC level of the same. Peak-to-peak noise (noncommon
mode) on VREF may not exceed ±2 percent of the DC value. Thus, from
VCCQ/2, VREF is allowed ±25mV for DC error and an additional ±25mV for
AC noise. This measurement is to be taken at the nearest VREF by-pass
capacitor.
7. VTT is not applied directly to the device. VTT is a system supply for signal
termination resistors, is expected to be set equal to VREF and must track
variations in the DC level of VREF.
8. VID is the magnitude of the difference between the input level on CLK and
the input level on CLK#.
9. The value of VIX and VMP are expected to equal VCCQ/2 of the transmitting
device and must track variations in the DC level of the same.
10. ICC is dependent on output loading and cycle rates. Specified values are
obtained with minimum cycle time with the outputs open.
15. The CLK/CLK# input reference level (for timing referenced to CLK/CLK#)
is the point at which CLK and CLK# cross; the input reference level for
signals other than CLK/CLK# is VREF.
16. Inputs are not recognized as valid until VREF stabilizes. Exception: during the
period before VREF stablizes, CKE < 0.3 x VCCQ is recognized as LOW.
17. The output timing reference level, as measured at the timing reference
point indicated in Note 3, is VTT.
18. t HZ and tLZ transitions occur in the same access time windows as valid
data transitions. These parameters are not referenced to a specific voltage
level, but specify when the device output is no longer driving (HZ) or
begins driving (LZ).
19. The maximum limit for this parameter is not a device limit. The device will
operate with a greater value for this parameter, but system performance
(bus turnaround) will degrade accordingly.
20. This is not a device limit. The device will operate with a negative value, but
system performance could be degraded due to bus turnaround.
21. It is recommended that DQS be valid (HIGH or LOW) on or before the
WRITE command. The case shown (DQS going from High-Z to logic LOW)
applies when no WRITEs were previously in progress on the bus. If a
previous WRITE was in progress, DQS could be HIGH during this time,
depending on tDQSS.
22. MIN (tRC or tRFC) for ICC measurements is the smallest multiple of tCK that
meets the minimum absolute value for the respective parameter. t RAS
(MAX) for ICC measurements is the largest multiple of tCK that meets the
maximum absolute value for tRAS.
23. The refresh period 64ms. This equates to an average refresh rate of
However, an AUTO REFRESH command must be asserted at least once
24.
25.
26.
27.
11. Enables on-chip refresh and address counters.
12. ICC specifications are tested after the device is properly initialized, and is 28.
averaged at the defined cycle rate.
13. This parameter is not tested but guaranteed by design. tA = 25OC, f = 1
MHz
14. Command/Address input slew rate = 0.5V/ns. For 266 MHz with slew rates
1V/ns and faster, tIS and tIH are reduced to 900ps. If the slew rate is less
than 0.5V/ns, timing must be derated: tIS has an additional 50ps per each
100mV/ns reduction in slew rate from the 500mV/ns. tIH has 0ps added,
that is, it remains constant. If the level, slew rate exceeds 4.5V/ns,
functionality is uncertain.
FIGURE A - PULL-DOWN CHARACTERISTICS
every 70.3µs; burst refreshing or posting by the DRAM controller greater
than eight refresh cycles is not allowed.
The I/O capacitance per DQS and DQ byte/group will not differ by more
than this maximum amount for any given device.
The valid data window is derived by achieving other specifications - tHP
(tCK /2), tDQSQ, and tQH (tQH = tHP - tQHS). The data valid window derates
directly porportional with the clock duty cycle and a practical data valid
window can be derived. The clock is allowed a maximum duty cycle
variation of 45/55. Functionality is uncertain when operating beyond a
45/55 ratio. The data valid window derating curves are provided
Referenced to each output group: LDQS with DQ0-DQ7; and UDQS with
DQ8-DQ15 of each chip.
This limit is actually a nominal value and does not result in a fail value.
CKE is HIGH below for duty cycles ranging between 50/50 and 45/55.
during REFRESH command period (t RFC [MIN]) else CKE is LOW (i.e.,
during standby)
To maintain a valid level, the transitioning edge of the input must:
a) Sustain a constant slew rate from the current AC level through to the
target AC level, VIL(AC) or VIH(AC).
b) Reach at least the target AC level.
c) After the AC target level is reached, continue to maintain at least the
target DC level, VIL(DC) or VIH(DC).
FIGURE B - PULL-UP CHARACTERISTICS
0
160
Maximum
140
-20
Minimum
-40
120
IOUT (mA)
IOUT (mA)
Nominal low
-60
Nominal high
100
80
Nominal low
60
Minimum
-80
-100
Nominal high
-120
-140
40
-160
20
-180
0
Maximum
-200
0.0
0.5
1.0
1.5
2.0
2.5
0.0
AS4DDR32M72PBG
Rev. 1.2 06/09
0.5
1.0
1.5
2.0
2.5
VCCQ - VOUT (V)
VOUT (V)
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
15
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
29. The Input capacitance per pin group will not differ by more than this
maximum amount for any given device.
30. CLK and CLK# input slew rate must be > 1V/ns (>2V/ns differentially).
31. DQ and DM input slew rates must not deviate from DQS by more than
10%. If the DQ/DM/DQS slew rate is less than 0.5V/ns, timing must be
derated: 50ps must be added to tDS and tDH for each 100mV/ns reduction
in slew rate. If slew rate exceeds 4V/ns, functionality is uncertain.
32. VCC must not vary more than 4% if CKE is not active while any bank is
active.
33. The clock is allowed up to ±150ps of jitter. Each timing parameter is
allowed to vary by the same amount.
34. tHP min is the lesser of tCL minimum and tCH minimum actually applied to
the device CLK and CLK# inputs, collectively during bank active.
35. READs and WRITEs with auto precharge are not allowed to be issued until
tRAS(MIN) can be satisfied prior to the internal precharge command being
issued.
36. Any positive glitch must be less than 1/3 of the clock and not more than
+400mV or 2.9 volts, whichever is less. Any negative glitch must be less
than 1/3 of the clock cycle and not exceed either -300mV or 2.2 volts,
whichever is more positive.
37. Normal Output Drive Curves:
a) The full variation in driver pull-down current from minimum to maximum
process, temperature and voltage will lie within the outer bounding lines
of the V-I curve of Figure A.
b) The variation in driver pull-down current within nominal limits of voltage
and temperature is expected, but not guaranteed, to lie within the inner
bounding lines of the V-I curve of Figure A.
c) The full variation in driver pull-up current from minimum to maximum
process, temperature and voltage will lie within the outer bounding lines
of the V-I curve of Figure B.
d) The variation in driver pull-up current within nominal limits of voltage
and temperature is expected, but not guaranteed, to lie within the inner
bounding lines of the V-I curve of Figure B.
e) The full variation in the ratio of the maximum to minimum pull-up
and pull-down current should be between .71 and 1.4, for device drainto-source voltages from 0.1V to 1.0 Volt, and at the same voltage and
temperature.
f) The full variation in the ratio of the nominal pull-up to pull-down current
should be unity ¡À10%, for device drain-to-source voltages from 0.1V
to 1.0 Volt.
38. Reduced Output Drive Curves:
a) The full variation in driver pull-down current from minimum to maximum
process, temperature and voltage will lie within the outer bounding lines
of the V-I curve of Figure C.
b) The variation in driver pull-down current within nominal limits of voltage
and temperature is expected, but not guaranteed, to lie within the inner
bounding lines of the V-I curve of Figure C.
c) The full variation in driver pull-up current from minimum to maximum
process, temperature and voltage will lie within the outer bounding lines
of the V-I curve of Figure D.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
FIGURE C - PULL-DOWN CHARACTERISTICS
d) The variation in driver pull-up current within nominal limits of voltage
and temperature is expected, but not guaranteed, to lie within the inner
bounding lines of the V-I curve of Figure B.
e) The full variation in the ratio of the maximum to minimum pull-up
and pull-down current should be between .71 and 1.4, for device drainto-source voltages from 0.1V to 1.0 Volt, and at the same voltage and
temperature.
f) The full variation in the ratio of the nominal pull-up to pull-down current
should be unity ±10%, for device drain-to-source voltages from 0.1V
to 1.0 Volt.
The voltage levels used are derived from a minimum V CC level and the
referenced test load. In practice, the voltage levels obtained from a
properly terminated bus will provide significantly different voltage values.
V IH overshoot: V IH (MAX) = V CCQ +1.5V for a pulse width < 3ns and the
pulse width can not be greater than 1/3 of the cycle rate.
V CC and V CCQ must track each other.
This maximum value is derived from the referenced test load. In practice,
the values obtained in a typical terminated design may reflect up to
310ps less for t HZ (MAX) and the last DVW. t HZ (MAX) will prevail over
t DQSCK (MAX) + t RPST (MAX) condition. t LZ (MIN) will prevail over t DQSCK (MIN)
+ t RPRE (MAX) condition.
For slew rates greater than 1V/ns the (LZ) transition will start about 310ps
earlier.
During initialization, V CCQ , V TT , and V REF must be equal to or less than V CC
+ 0.3V. Alternatively, V TT may be 1.35V maximum during power up, even
if V CC /V CCQ are 0 volts, provided a minimum of 42 ohms of series
resistance is used between the V TT supply and the input pin.
The current part operates below the slowest JEDEC operating frequency
of 83 MHz.
As such, future die may not reflect this option.
Reserved for future use.
Reserved for future use.
Random addressing changing 50% of data changing at every transfer.
Random addressing changing 100% of data changing at every transfer.
CKE must be active (high) during the entire time a refresh command is
executed. That is, from the time the AUTO REFRESH command is
registered, CKE must be active at each rising clock edge, until t RFC has
been satisfied.
I CC2N specifies the DQ, DQS, and DM to be driven to a valid high or low
logic level. I CC2Q is similar to I CC2F except I CC2Q specifies the address
and control inputs to remain stable. Although I CC2F , I CC2N , and I CC2Q are
similar, I CC2F is “worst case.”
Whenever the operating frequency is altered, not including jitter, the DLL
is required to be reset. This is followed by 200 clock cycles before any
READ command.
V TT is not applied directly to the device; however, t VTD should be greater
than or equal to zero to avoid device latch-up. V CCQ , V TT and V REF must
be equal to or less than V CC + 0.3V. Alternatively V TT may be 1.35V max
during power-up even if V CC /V CCQ are 0V, provided a minimum of 42 &! of
series resistance is used between the V TT supply and the input pin. Once
initialized, V REF must always be powered within the specified range.
FIGURE D - PULL-UP CHARACTERISTICS
0
80
Maximum
-10
70
60
Nominal high
40
IOUT (mA)
IOUT (mA)
50
Nominal low
-20
Minimum
-30
Nominal low
-40
-50
30
Minimum
Nominal high
20
-60
10
-70
0
-80
Maximum
0.0
0.5
1.0
1.5
2.0
0.0
2.5
AS4DDR32M72PBG
Rev. 1.2 06/09
0.5
1.0
1.5
2.0
2.5
VCCQ - VOUT (V)
VOUT (V)
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
16
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
PACKAGE DIMENSION: 219 PLASTIC BALL GRID ARRAY (PBGA)
Bottom View
32.1 (1.264) MAX
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
19.05
(0.750)
NOM
1.27
(0.050)
NOM
25.1
(0.988)
MAX
0.61
(0.024)
NOM
219 X Ø 0.762 (0.030) NOM
2.03 (0.080)
MAX
19.05 (0.750) NOM
ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES
AS4DDR32M72PBG
Rev. 1.2 06/09
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
17
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
ORDERING INFORMATION
Part Number
AS4DDR32M72-6/IT
AS4DDR32M72-75/IT
AS4DDR32M72-8/IT
AS4DDR32M72-10/IT
Core Freq. Data Transfer Rate
166 MHz
333 Mbps
133 MHz
266 Mbps
125 MHz
250 Mbps
100 MHz
200 Mbps
Package
Process
219-PBGA Industrial
219-PBGA Industrial
219-PBGA Industrial
219-PBGA Industrial
AS4DDR32M72-75/ET
AS4DDR32M72-8/ET
AS4DDR32M72-10/ET
133 MHz
125 MHz
100 MHz
266 Mbps
250 Mbps
200 Mbps
219-PBGA
219-PBGA
219-PBGA
Enhanced
Enhanced
Enhanced
AS4DDR32M72-75/XT
AS4DDR32M72-8/XT
AS4DDR32M72-10/XT
133 MHz
125 MHz
100 MHz
266 Mbps
250 Mbps
200 Mbps
219-PBGA
219-PBGA
219-PBGA
Military
Military
Military
AS4DDR32M72PBG
Rev. 1.2 06/09
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
18
i PEM
2.4G
b SDRAM-DDR
2.4Gb
Austin Semiconductor, Inc. AS4DDR32M72PBG
DOCUMENT TITLE
32M x 72 DDR SDRAM Multi-Chip Packaged in a 32mm x 25mm - 219 PBGA
REVISION HISTORY
Rev #
1.0
1.1
1.2
AS4DDR32M72PBG
Rev. 1.2 06/09
History
Release Date
RELEASE
March 2005
added configuration addressing table
September 2008
to page 1
Updated Order Chart
June 2009
Changed from “Extended” to “Military” Temp
Status
Preliminary
Preliminary
Release
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
19
Similar pages