PulseCore ASM3P2760AG-08ST Low power peak emi reducing solution Datasheet

ASM3P2760A
January 2007
rev 1.9
Low Power Peak EMI Reducing Solution
Features
•
The ASM3P2760A uses the most efficient and optimized
modulation profile approved by the FCC and is
Generates an EMI optimized clock signal at the
implemented by using a proprietary all digital method.
output.
•
Integrated loop filter components.
•
Operates with a 3.3V / 2.5V Supply.
•
Operating current less than 4mA.
•
Low power CMOS design.
•
Input frequency range: 6MHz to 12MHz for 2.5V.
The ASM3P2760A modulates the output of a single PLL
in order to “spread” the bandwidth of a synthesized clock,
and more importantly, decreases the peak amplitudes of
: 6MHz to 13MHz for 3.3V.
•
Generates a 1X low EMI spread spectrum clock
its harmonics. This results in significantly lower system
EMI compared to the typical narrow band signal produced
by oscillators and most frequency generators. Lowering
EMI by increasing a signal’s bandwidth is called ‘spread
of the input frequency.
spectrum clock generation’.
•
Frequency deviation: ±0.65% @ 8MHz
•
Available in 6 pin TSOT-23, 8 pin SOIC and
•
8 pin TSSOP Packages.
Applications
The ASM3P2760A is targeted towards all portable
Product Description
devices with very low power requirements like MP3
The ASM3P2760A is a versatile spread spectrum
frequency modulator designed specifically for a wide
range of clock frequencies. The ASM3P2760A reduces
electromagnetic interference (EMI) at the clock source,
allowing system wide reduction of EMI of
all clock
players and digital still cameras.
Key Specifications
Description
Specification
Supply voltages
VDD = 3.3V / 2.5V
system cost savings by reducing the number of circuit
Cycle-to-Cycle Jitter
200pS (Max)
board layers ferrite beads, shielding that are traditionally
Output Duty Cycle
45/55%
required to pass EMI regulations.
Modulation Rate Equation
FIN/256
Frequency Deviation
±0.65% @ 8MHz
dependent signals. The ASM3P2760A allows significant
Block Diagram
VDD
PLL
Modulation
XIN
XOUT
PD
Crystal
Oscillator
Frequency
Divider
Feedback
Divider
Phase
Detector
Loop
Filter
VCO
Output
Divider
VSS
PulseCore Semiconductor Corporation
1715 S. Bascom Ave Suite 200, Campbell, CA 95008 • Tel: 408-879-9077 • Fax: 408-879-9018
www.pulsecoresemi.com
Notice: The information in this document is subject to change without notice.
ModOUT
ASM3P2760A
January 2007
rev 1.9
Pin Configuration (6-pin TSOT-23 Package)
PD 1
XOUT 2
ASM3P2760A
XIN/CLKIN 3
6
VSS
5
ModOUT
4
VDD
Pin Description
Pin#
1
2
Pin Name
PD
XOUT
Type
I
Description
Power-down control pin. Pull low to enable power-down mode. Connect to VDD if not
used.
O
Crystal connection. If using an external reference, this pin must be left unconnected.
3
XIN/CLKIN
I
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
4
VDD
P
Power supply for the entire chip
5
ModOUT
O
Spread spectrum clock output.
6
VSS
P
Ground connection.
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
2 of 12
ASM3P2760A
January 2007
rev 1.9
Pin Configuration (8-pin SOIC and TSSOP Packages)
XIN/CLKIN 1
8
VDD
7
NC
PD 3
6
ModOUT
NC 4
5
VSS
XOUT 2
ASM3P2760A
Pin Description
Pin#
Pin Name
Type
Description
1
XIN/CLKIN
I
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
2
XOUT
O
Crystal connection. If using an external reference, this pin must be left unconnected.
I
Power-down control pin. Pull low to enable power-down mode. Connect to VDD if not
used.
3
PD
4
NC
-
No connect.
5
VSS
P
Ground connection.
6
ModOUT
O
Spread spectrum clock output.
7
NC
-
No connect.
8
VDD
P
Power supply for the entire chip
Modulation Profile
Specification
Description
Frequency Range
For 2.5V Supply
For 3.3V Supply
Specification
6MHz < CLKIN < 12MHz
6MHz < CLKIN < 13MHz
Modulation Equation
FIN/256
Frequency Deviation
±0.65% @ 8MHz
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
3 of 12
ASM3P2760A
January 2007
rev 1.9
Absolute Maximum Ratings
Symbol
VDD, VIN
TSTG
Parameter
Rating
Unit
Voltage on any pin with respect to Ground
-0.5 to +4.6
V
Storage temperature
-65 to +125
°C
TA
Operating temperature
-40 t0 +85
°C
Ts
Max. Soldering Temperature (10 sec)
260
°C
TJ
Junction Temperature
150
°C
2
KV
TDV
Static Discharge Voltage
(As per JEDEC STD22- A114-B)
Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability.
DC Electrical Characteristics for 2.5V Supply
(Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated)
Symbol
Parameter
Min
Typ
Max
Unit
VIL
Input low voltage
VSS-0.3
-
0.8
V
VIH
Input high voltage
2.0
-
VDD+0.3
V
IIL
Input low current
-
-
-35
µA
IIH
Input high current
-
-
35
µA
IXOL
XOUT output low current (@0.5V, VDD=2.5V)
-
3
-
mA
IXOH
XOUT output high current (@1.8V, VDD=2.5V)
-
3
-
mA
VOL
Output low voltage (VDD = 2.5V, IOL = 8mA)
-
-
0.6
V
VOH
Output high voltage (VDD = 2.5V, IOH = 8mA)
1.8
-
-
V
IDD
Static supply current*
-
-
10
µA
ICC
Dynamic supply current (2.5V, 8MHz and no load)
-
2.5
-
mA
VDD
tON
ZOUT
Operating Voltage
2.375
2.5
2.625
V
Power-up time (first locked cycle after power-up)**
-
-
5
mS
Output impedance
-
50
-
Ω
* XIN/CLKIN pin and PD pin are pulled low
** VDD and XIN/CLKIN input are stable, PD pin is made high from low.
AC Electrical Characteristics for 2.5V Supply
Symbol
CLKIN
ModOUT
fd
Parameter
Min
Typ
Max
Unit
Input frequency
6
-
12
MHz
Output frequency
6
-
12
MHz
Input Frequency = 6MHz
-
±1.0
-
Input Frequency = 12MHz
-
±0.45
-
Frequency Deviation
%
tLH*
Output rise time (measured from 0.7V to 1.7V)
0.4
1.2
1.4
nS
tHL*
Output fall time (measured from 1.7V to 0.7V)
0.4
0.9
1.1
nS
tJC
Jitter (cycle to cycle)
-
-
200
pS
tD
Output duty cycle
45
50
55
%
* tLH and tHL are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
4 of 12
ASM3P2760A
January 2007
rev 1.9
DC Electrical Characteristics for 3.3V Supply
(Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated.)
Symbol
Parameter
Min
Typ
Max
Unit
-
0.8
V
VIL
Input low voltage
VSS - 0.3
VIH
Input high voltage
2.0
-
VDD + 0.3
V
IIL
Input low current
-
-
-35
µA
IIH
Input high current
-
-
35
µA
IXOL
XOUT output low current (@0.4V, VDD=3.3V)
-
3
-
mA
IXOH
XOUT output high current (@2.5V, VDD=3.3V)
-
3
-
mA
VOL
Output low voltage (VDD = 3.3 V, IOL = 8mA)
-
-
0.4
V
VOH
Output high voltage (VDD = 3.3 V, IOH = 8mA)
2.5
-
-
V
IDD
Static supply current*
-
-
10
µA
ICC
Dynamic supply current (3.3V, 8MHz and no load)
-
3.0
-
mA
VDD
Operating Voltage
tON
ZOUT
2.7
3.3
3.6
V
Power-up time(first locked cycle after power up)**
-
-
5
mS
Output impedance
-
45
-
Ω
* XIN/CLKIN pin and PD pin are pulled low
**VDD and XIN/CLKIN input are stable; PD pin is made high from low.
AC Electrical Characteristics for 3.3V Supply
Symbol
CLKIN
ModOUT
fd
Parameter
Min
Typ
Max
Unit
Input frequency
6
-
13
MHz
Output frequency
6
-
13
MHz
Input Frequency = 6MHz
-
±1.0
-
Input Frequency = 13MHz
-
±0.4
-
Frequency Deviation
%
tLH*
Output rise time (measured at 0.8V to 2.0V)
0.5
1.3
1.5
nS
tHL*
Output fall time (measured at 2.0V to 0.8V)
0.4
1.0
1.2
nS
tJC
Jitter (cycle to cycle)
-
-
200
pS
tD
Output duty cycle
45
50
55
%
*tLH and tHL are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
5 of 12
ASM3P2760A
January 2007
rev 1.9
Typical Crystal Oscillator Circuit
Crystal
R1 = 510Ω
C1 = 27 pF
C2 = 27 pF
Typical Crystal Specifications
Fundamental AT cut parallel resonant crystal
Nominal frequency
8.000MHz
Frequency tolerance
± 50ppm or better at 25°C
Operating temperature range
-25°C to +85°C
Storage temperature
-40°C to +85°C
Load capacitance
18pF
Shunt capacitance
7pF maximum
ESR
25Ω
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
6 of 12
ASM3P2760A
January 2007
rev 1.9
Package Information
6-pin TSOT-23 Package
Dimensions
Symbol
Inches
Min
A
Max
Millimeters
Min
Max
0.04
1.00
A1
0.00
0.004
0.00
0.10
A2
0.033
0.036
0.84
0.90
b
0.012
0.02
0.30
0.50
H
0.005 BSC
0.127 BSC
D
0.114 BSC
2.90 BSC
B
0.06 BSC
1.60 BSC
e
0.0374 BSC
0.950 BSC
C
0.11 BSC
2.80 BSC
L
0.0118
0.02
0.30
0.50
θ
0°
4°
0°
4°
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
7 of 12
ASM3P2760A
January 2007
rev 1.9
8-Pin SOIC Package
H
E
D
A2
A
C
A1
D
θ
e
L
B
Dimensions
Symbol
Inches
Min
Max
Millimeters
Min
Max
A1
0.004
0.010
0.10
0.25
A
0.053
0.069
1.35
1.75
A2
0.049
0.059
1.25
1.50
B
0.012
0.020
0.31
0.51
C
0.007
0.010
0.18
0.25
D
0.193 BSC
4.90 BSC
E
0.154 BSC
3.91 BSC
e
0.050 BSC
1.27 BSC
H
0.236 BSC
6.00 BSC
L
0.016
0.050
0.41
1.27
θ
0°
8°
0°
8°
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
8 of 12
ASM3P2760A
January 2007
rev 1.9
8-Pin TSSOP Package
H
E
D
A2
A
C
θ
e
A1
L
B
Dimensions
Symbol
Inches
Min
Millimeters
Max
A
Min
Max
0.043
1.10
A1
0.002
0.006
0.05
0.15
A2
0.033
0.037
0.85
0.95
B
0.008
0.012
0.19
0.30
c
0.004
0.008
0.09
0.20
D
0.114
0.122
2.90
3.10
E
0.169
0.177
4.30
4.50
e
0.026 BSC
0.65 BSC
H
0.252 BSC
6.40 BSC
L
0.020
0.028
0.50
0.70
θ
0°
8°
0°
8°
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
9 of 12
ASM3P2760A
January 2007
rev 1.9
Ordering Information
Part Number
Marking
Package Type
Temperature
ASM3P2760AF-06OR
E4LL
6-Pin TSOT-23, TAPE & REEL, Pb Free
Commercial
ASM3P2760AF-08TT
3P2760AF
8-Pin TSSOP, TUBE, Pb Free
Commercial
ASM3P2760AF-08TR
3P2760AF
8-Pin TSSOP, TAPE & REEL, Pb Free
Commercial
ASM3P2760AF-08ST
3P2760AF
8-Pin SOIC, TUBE, Pb Free
Commercial
ASM3P2760AF-08SR
3P2760AF
8-Pin SOIC, TAPE & REEL, Pb Free
Commercial
ASM3P2760AG-06OR
E3LL
6-Pin TSOT-23, TAPE & REEL, Green
Commercial
ASM3P2760AG-08TT
3P2760AG
8-Pin TSSOP, TUBE, Green
Commercial
ASM3P2760AG-08TR
3P2760AG
8-Pin TSSOP, TAPE & REEL, Green
Commercial
ASM3P2760AG-08ST
3P2760AG
8-Pin SOIC, TUBE, Green
Commercial
ASM3P2760AG-08SR
3P2760AG
8-Pin SOIC, TAPE & REEL, Green
Commercial
ASM3I2760AF-06OR
E5LL
6-Pin TSOT-23, TAPE & REEL, Pb Free
Industrial
ASM3I2760AF-08TT
3I2760AF
8-Pin TSSOP, TUBE, Pb Free
Industrial
ASM3I2760AF-08TR
3I2760AF
8-Pin TSSOP, TAPE & REEL, Pb Free
Industrial
ASM3I2760AF-08ST
3I2760AF
8-Pin SOIC, TUBE, Pb Free
Industrial
ASM3I2760AF-08SR
3I2760AF
ASM3I2760AG-06OR
E6LL
ASM3I2760AG-08TT
8-Pin SOIC, TAPE & REEL, Pb Free
Industrial
6-Pin TSOT-23, TAPE & REEL, Green
Industrial
3I2760AG
8-Pin TSSOP, TUBE, Green
Industrial
ASM3I2760AG-08TR
3I2760AG
8-Pin TSSOP, TAPE & REEL, Green
Industrial
ASM3I2760AG-08ST
3I2760AG
8-Pin SOIC, TUBE, Green
Industrial
ASM3I2760AG-08SR
3I2760AG
8-Pin SOIC, TAPE & REEL, Green
Industrial
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
10 of 12
ASM3P2760A
January 2007
rev 1.9
Device Ordering Information
A S M 3 P 2 7 6 0 A F - 0 8 T R
R = Tape & Reel, T = Tube or Tray
O = TSOT23
S = SOIC
T = TSSOP
A = SSOP
V = TVSOP
B = BGA
Q = QFN
U = MSOP
E = TQFP
L = LQFP
U = MSOP
P = PDIP
D = QSOP
X = SC-70
J=TSOT26
DEVICE PIN COUNT
F = LEAD FREE AND RoHS COMPLIANT PART
G = GREEN PACKAGE, LEAD FREE, and RoHS
PART NUMBER
X= Automotive
I= Industrial
P or n/c = Commercial
(-40C to +125C) (-40C to +85C)
(0C to +70C)
1 = Reserved
2 = Non PLL based
3 = EMI Reduction
4 = DDR support products
5 = STD Zero Delay Buffer
6 = Power Management
7 = Power Management
8 = Power Management
9 = Hi Performance
0 = Reserved
PulseCore Semiconductor Mixed Signal Product
Licensed under U.S Patent Nos 5,488,627 and 5,631,921
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
11 of 12
ASM3P2760A
January 2007
rev 1.9
PulseCore Semiconductor Corporation
1715 S. Bascom Ave Suite 200
Campbell, CA 95008
Tel: 408-879-9077
Fax: 408-879-9018
www.pulsecoresemi.com
Copyright © PulseCore Semiconductor
All Rights Reserved
Part Number: ASM3P2760A
Document Version: 1.9
Note: This product utilizes US Patent # 6,646,463 Impedance Emulator Patent issued to PulseCore Semiconductor, dated 11-11-2003
© Copyright 2007 PulseCore Semiconductor Corporation. All rights reserved. Our logo and name are trademarks or
registered trademarks of PulseCore Semiconductor. All other brand and product names may be the trademarks of their
respective companies. PulseCore reserves the right to make changes to this document and its products at any time
without notice. PulseCore assumes no responsibility for any errors that may appear in this document. The data contained
herein represents PulseCore’s best data and/or estimates at the time of issuance. PulseCore reserves the right to change
or correct this data at any time, without notice. If the product described herein is under development, significant changes to
these specifications are possible. The information in this product data sheet is intended to be general descriptive
information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to
any user or customer. PulseCore does not assume any responsibility or liability arising out of the application or use of any
product described herein, and disclaims any express or implied warranties related to the sale and/or use of PulseCore
products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any
intellectual property rights, except as express agreed to in PulseCore’s Terms and Conditions of Sale (which are available
from PulseCore). All sales of PulseCore products are made exclusively according to PulseCore’s Terms and Conditions of
Sale. The purchase of products from PulseCore does not convey a license under any patent rights, copyrights; mask
works rights, trademarks, or any other intellectual property rights of PulseCore or third parties. PulseCore does not
authorize its products for use as critical components in life-supporting systems where a malfunction or failure may
reasonably be expected to result in significant injury to the user, and the inclusion of PulseCore products in such lifesupporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify PulseCore against
all claims arising from such use.
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
12 of 12
Similar pages