MA-COM AT-233-PIN Digital attenuator Datasheet

AT-233-PIN
Digital Attenuator
30.0 dB, 4-Bit, TTL Driver, DC-2.0 GHz
Features
Rev. V5
Functional Schematic
• Attenuation: 2 dB Steps to 30 dB
• Temperature Stability: ± 0.18 dB from –55°C to
+85°C Typical
• Low DC Power Consumption
• Hermetic Surface Mount Package
• Integral TTL Driver
• 50 Ohm Nominal Impedance
• Lead-Free CR-12 Package
• 260°C Reflow Compatible
• RoHS* Compliant
Description
M/A-COM’s AT-233-PIN is a GaAs FET 4-Bit digital
attenuator with a 2 dB minimum step size and 30 dB
total attenuation. This attenuator and integral TTL
driver is in a hermetically sealed ceramic 16-lead
surface mount package. The AT-233-PIN is ideally
suited for use where accuracy, fast switching, very
low power consumption and low intermodulation
products are required. Typical applications include
dynamic range setting in precision receiver circuits
and other gain/leveling control circuits. Environmental screening is available. Contact the factory
for information.
Pin Configuration
Pin No.
Function
Pin No.
Function
1
RF1
9
NC
2
GND
10
+5V
3
GND
11
-5V
4
GND
12
C4
5
GND
13
C3
6
GND
14
C2
7
GND
15
C1
8
RF2
16
GND
Ordering Information
Part Number
Package
AT-233-PIN
Bulk Packaging
MAAD-007228-0001TR
1000 piece reel
MAAD-007228-0001TB
Sample Test Board
The metal bottom of the case must be connected to RF and DC
ground.
Note: Reference Application Note M513 for reel size
information.
* Restrictions on Hazardous Substances, European Union Directive 2002/95/EC.
1
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
is considering for development. Performance is based on target specifications, simulated results,
• India Tel: +91.80.4155721
• China Tel: +86.21.2407.1588
and/or prototype measurements. Commitment to develop is not guaranteed.
Visit www.macomtech.com for additional data sheets and product information.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.
AT-233-PIN
Digital Attenuator
30.0 dB, 4-Bit, TTL Driver, DC-2.0 GHz
Rev. V5
Electrical Specifications: TA = 25°C1
Parameter
Test Conditions
Frequency
Units
Min
Typ
Max
Reference Insertion Loss
—
DC - 0.5 GHz
DC - 1.0 GHz
DC - 2.0 GHz
dB
dB
dB
—
—
—
—
—
—
2.3
2.65
2.8
Attenuation Accuracy2
Any Single Bit
DC - 1.0 GHz
DC - 2.0 GHz
Any Combination of Bits
DC - 1.0 GHz
DC - 2.0 GHz
± (0.2 + 3% of attenuation setting in dB) dB
± (0.2 + 3% of attenuation setting in dB) dB
or ± 0.45 dB, whichever is greater
± (0.20 + 3% of attenuation setting in dB) dB
± (0.25 + 4% of attenuation setting in dB) dB
or ± 0.45 dB, whichever is greater
VSWR
—
DC - 2.0 GHz
Ratio
—
—
1.7:1
Trise, Tfall
10% to 90%
—
ns
—
10
—
Ton, Toff
50% Control to 90/10% RF
—
ns
—
30
—
Transients
In-Band (peak-peak)
—
mV
—
35
—
1 dB Compression 3
Input Power
0.05 GHz
0.5 - 2.0 GHz
dBm
dBm
—
—
+20
+28
—
—
Input IP3 3
For two tone input power
Up to +5 dBm
0.05 GHz
0.5 - 2.0 GHz
dBm
dBm
—
—
+40
+50
—
—
Input IP2 3
For two-tone input power
Up to +5 dBm
0.05 GHz
0.5 - 2.0 GHz
dBm
dBm
—
—
+45
+68
—
—
VCC
—
—
V
4.5
5.0
5.5
VEE
—
—
V
-8.0
—
-5.0
ICC
VCC = 4.5 to 5.5 V
Vctl = 0 to 0.8V, or VCC –
2.1V to VCC
—
mA
—
—
4.0
IEE
VEE = -5.0 to –8.0V
—
mA
—
—
1.0
Vctl
Logic 0 (TTL)
Logic 1 (TTL)
—
—
V
V
0.0
2.0
—
—
0.8
5.0
Input Leakage Current (Low)
Input Leakage Current (High)
0 to 0.8V
2.0 to 5.0V
—
—
µA
µA
—
—
—
—
1.0
1.0
1. All specifications apply when operated with bias voltages of +5V for VCC and –5.0V to –8.0V for VEE, and 50 Ohm impedance at all ports
unless otherwise specified.
2. This attenuator is guaranteed monotonic.
3. VEE = -5V for the typical numbers given.
2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
is considering for development. Performance is based on target specifications, simulated results,
• India Tel: +91.80.4155721
• China Tel: +86.21.2407.1588
and/or prototype measurements. Commitment to develop is not guaranteed.
Visit www.macomtech.com for additional data sheets and product information.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.
AT-233-PIN
Digital Attenuator
30.0 dB, 4-Bit, TTL Driver, DC-2.0 GHz
Rev. V5
Recommended PCB Configuration
Absolute Maximum Ratings 4,5
Parameter
Absolute Maximum
Max Input Power
0.5 GHz
0.5 - 2.0 GHz
+27 dBm
+34 dBm
VCC
-0.5V ≤ VCC ≤ +7.0V
VEE
-8.5V ≤ VEE ≤ +0.5V
VCC - VEE
-0.5V ≤ VCC - VEE ≤ 14.5V
Vin
4.
5.
6.
6
-0.5V ≤ Vin ≤ VCC + 0.5V
Operating Temperature
-55°C to +125°C
Storage Temperature
-65°C to +150°C
Exceeding any one or combination of these limits may cause
permanent damage to this device.
M/A-COM does not recommend sustained operation near
these survivability limits.
Standard CMOS TTL interface, latch-up will occur if logic
signal is applied prior to power supply.
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
Typical Performance Curves
+ 2 5 °C
Control Inputs
C4
C3
C2
C1
Attenuation
0
0
0
0
Reference
0
0
0
1
2 dB
0
0
1
0
4 dB
0
1
0
0
8 dB
1
0
0
0
16 dB
1
1
1
1
30 dB
0 = TTL Low; 1 = TTL High
VSWR vs. Frequency
Ref. Insertion Loss vs. Frequency
+ 8 5 °C
Truth Table (Digital Attenuator)
- 55 °C
2 dB
5.0
4 dB
8 d B 16 d B
R ef Lo ss St at e
4.0
1.80
3.0
VSWR
Insertion Loss (dB)
2.00
2.0
1.60
1.40
1.0
1.20
0.0
0.0
0.5
1.0
Fre que ncy (GHz )
1.5
2.0
1.00
0.0
0.5
1.0
1.5
2.0
Fre que ncy (GHz )
3
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
is considering for development. Performance is based on target specifications, simulated results,
• India Tel: +91.80.4155721
• China Tel: +86.21.2407.1588
and/or prototype measurements. Commitment to develop is not guaranteed.
Visit www.macomtech.com for additional data sheets and product information.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.
AT-233-PIN
Digital Attenuator
30.0 dB, 4-Bit, TTL Driver, DC-2.0 GHz
Rev. V5
Lead-Free CR-12 Ceramic Package†
Typical Performance Curves
Attenuation Accuracy vs. Frequency
D ev ia tio n fro m N o m ina l
A ttenua tio n (dB)
F ull A t t en
16 d B
8 dB
4 dB
2 dB
1.0
0.5
0.0
-0.5
-1.0
-1.5
-2.0
0.0
0.5
1.0
1.5
2.0
Frequency (GHz)
†
Reference Application Note M538 for lead-free solder reflow
recommendations.
4
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
is considering for development. Performance is based on target specifications, simulated results,
• India Tel: +91.80.4155721
• China Tel: +86.21.2407.1588
and/or prototype measurements. Commitment to develop is not guaranteed.
Visit www.macomtech.com for additional data sheets and product information.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.
Similar pages