ATMEL AT25640T2-10TI-1.8 Spi serial eeprom Datasheet

Features
• Serial Peripheral Interface (SPI) Compatible
• Supports SPI Modes 0 (0,0) and 3 (1,1)
• Low Voltage and Standard Voltage Operation
•
•
•
•
•
•
•
•
– 5.0 (VCC = 4.5V to 5.5V)
– 2.7 (VCC = 2.7V to 5.5V)
– 1.8 (VCC = 1.8V to 3.6V)
2.1 MHz Clock Rate
32-Byte Page Mode
Block Write Protection
– Protect 1/4, 1/2, or Entire Array
Write Protect (WP) Pin and Write Disable Instructions for
Both Hardware and Software Data Protection
Self-Timed Write Cycle (5 ms Typical)
High Reliability
– Endurance: 1 Million Write Cycles
– Data Retention: 100 Years
– ESD Protection: >4000V
Automotive Grade and Extended Temperature Devices Available
8-Pin PDIP, JEDEC SOIC, and 14-Pin and 20-Pin TSSOP Packages
SPI Serial
EEPROMs
8K (1024 x 8)
16K (2048 x 8)
32K (4096 x 8)
Description
64K (8192 x 8)
The AT25080/160/320/640 provides 8192/16384/32768/65536 bits of serial electrically erasable programmable read only memory (EEPROM) organized as
1024/2048/4096/8192 words of 8 bits each. The device is optimized for use in many
industrial and commercial applications where low power and low voltage operation
(continued)
AT25080
AT25160
AT25320
AT25640
Pin Configuration
Pin Name
Function
CS
Chip Select
SCK
Serial Data Clock
SI
Serial Data Input
SO
Serial Data Output
GND
Ground
VCC
Power Supply
WP
Write Protect
HOLD
Suspends Serial Input
NC
No Connect
DC
Don’t Connect
8-Pin PDIP
CS
SO
WP
GND
1
2
3
4
8
7
6
5
8-Pin SOIC
VCC
HOLD
SCK
SI
14-Lead TSSOP
CS
SO
NC
NC
NC
WP
GND
1
2
3
4
5
6
7
14
13
12
11
10
9
8
VCC
HOLD
NC
NC
NC
SCK
SI
CS
SO
WP
GND
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
20-Lead TSSOP*
NC
CS
SO
SO
NC
NC
WP
GND
DC
NC
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
NC
VCC
HOLD
HOLD
NC
NC
SCK
SI
DC
NC
Rev. 0675C–08/98
*Pins 3, 4 and 17, 18 are internally connected for 14-lead TSSOP socket compatibility.
1
are essential. The AT25080/160/320/640 is available in
space saving 8-pin PDIP, JEDEC SOIC, and 14-pin and
20-pin TSSOP packages.
The AT25080/160/320/640 is enabled through the Chip
Select pin (CS) and accessed via a 3-wire interface consisting of Serial Data Input (SI), Serial Data Output (SO),
and Serial Clock (SCK). All programming cycles are completely self-timed, and no separate ERASE cycle is
required before WRITE.
BLOCK WRITE protection is enabled by programming the
status register with one of four blocks of write protection.
Separate program enable and program disable instructions
are provided for additional data protection. Hardware data
protection is provided via the WP pin to protect against
inadvertent write attempts to the status register. The HOLD
pin may be used to suspend any serial communication
without resetting the serial sequence.
Absolute Maximum Ratings*
Operating Temperature .................................. -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin
with Respect to Ground .....................................-1.0V to +7.0V
Maximum Operating Voltage........................................... 6.25V
DC Output Current........................................................ 5.0 mA
Block Diagram
2
AT25080/160/320/640
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
AT25080/160/320/640
Pin Capacitance(1)
Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +5.0V (unless otherwise noted).
Test Conditions
Max
Units
Conditions
COUT
Output Capacitance (SO)
8
pF
VOUT = 0V
CIN
Input Capacitance(CS, SCK, SI, WP, HOLD)
6
pF
VIN = 0V
Note:
1. This parameter is characterized and is not 100% tested.
DC Characteristics
Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = +1.8V to +5.5V, TAC = 0°C to +70°C,
VCC = +1.8V to +5.5V (unless otherwise noted).
Symbol
Parameter
VCC1
Supply Voltage
VCC2
Max
Units
1.8
3.6
V
Supply Voltage
2.7
5.5
V
VCC3
Supply Voltage
4.5
5.5
V
ICC1
Supply Current
VCC = 5.0V at 1 MHz, SO = Open
3.0
mA
ICC2
Supply Current
VCC = 5.0V at 2 MHz, SO = Open
5.0
mA
ISB1
Standby Current
VCC = 1.8V, CS = VCC
0.1
µA
ISB2
Standby Current
VCC = 2.7V, CS = VCC
0.2
0.5
µA
ISB3
Standby Current
VCC = 5.0V, CS = VCC
0.5
2.0
µA
IIL
Input Leakage
VIN = 0V to VCC
-3.0
3.0
µA
IOL
Output Leakage
VIN = 0V to VCC, TAC = 0°C to 70°C
-3.0
3.0
µA
Input Low Voltage
-0.6
VCC x 0.3
V
VIH(1)
Input High Voltage
VCC x 0.7
VCC + 0.5
V
VOL1
Output Low Voltage
0.4
V
VOH1
Output High Voltage
VOL2
Output Low Voltage
V
(1)
IL
VOH2
Note:
Output High Voltage
Test Condition
4.5V ≤ VCC ≤ 5.5V
1.8V ≤ VCC ≤ 3.6V
Min
IOL = 3.0 mA
IOH = -1.6 mA
VCC - 0.8
IOL = 0.15 mA
IOH = -100 µA
Typ
V
0.2
VCC - 0.2
V
V
1. VIL min and VIH max are reference only and are not tested.
3
AC Characteristics
Applicable over recommended operating range from TA = -40°C to +85°C, VCC = As Specified,
CL = 1 TTL Gate and 100 pF (unless otherwise noted).
Symbol
Parameter
Voltage
Min
Max
Units
fSCK
SCK Clock Frequency
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
0
0
0
2.1
2.1
0.5
MHz
tRI
Input Rise Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
2
2
2
µs
tFI
Input Fall Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
2
2
2
µs
tWH
SCK High Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
200
200
800
ns
tWL
SCK Low Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
200
200
800
ns
tCS
CS High Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
250
250
1000
ns
tCSS
CS Setup Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
250
250
1000
ns
tCSH
CS Hold Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
250
250
1000
ns
tSU
Data In Setup Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
50
50
100
ns
tH
Data In Hold Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
50
50
100
ns
tHD
Hold Setup Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
100
100
400
tCD
Hold Hold Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
200
200
400
tV
Output Valid
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
0
0
0
tHO
Output Hold Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
0
0
0
4
AT25080/160/320/640
ns
200
200
800
ns
ns
AT25080/160/320/640
AC Characteristics (Continued)
Applicable over recommended operating range from TA = -40°C to +85°C, VCC = As Specified,
CL = 1 TTL Gate and 100 pF (unless otherwise noted).
Symbol
Parameter
Voltage
Min
Max
Units
tLZ
Hold to Output Low Z
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
0
0
0
100
100
100
ns
tHZ
Hold to Output High Z
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
100
100
100
ns
tDIS
Output Disable Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
250
250
1000
ns
tWC
Write Cycle Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
5
10
20
ms
Endurance(1)
5.0V, 25°C, Page Mode
Note:
1M
Write Cycles
1. This parameter is characterized and is not 100% tested.
5
Serial Interface Description
MASTER: The device that generates the serial clock.
SLAVE: Because the Serial Clock pin (SCK) is always an
input, the AT25080/160/320/640 always operates as a
slave.
TRANSMITTER/RECEIVER: The AT25080/160/320/640
has separate pins designated for data transmission (SO)
and reception (SI).
MSB: The Most Significant Bit (MSB) is the first bit transmitted and received.
SERIAL OP-CODE: After the device is selected with CS
going low, the first byte will be received. This byte contains
the op-code that defines the operations to be performed.
INVALID OP-CODE: If an invalid op-code is received, no
data will be shifted into the AT25080/160/320/640, and the
serial output pin (SO) will remain in a high impedance state
until the falling edge of CS is detected again. This will reinitialize the serial communication.
CHIP SELECT: The AT25080/160/320/640 is selected
when the CS pin is low. When the device is not selected,
data will not be accepted via the SI pin, and the serial output pin (SO) will remain in a high impedance state.
HOLD: The HOLD pin is used in conjunction with the CS
pin to select the AT25080/160/320/640. When the device is
selected and a serial sequence is underway, HOLD can be
used to pause the serial communication with the master
device without resetting the serial sequence. To pause, the
HOLD pin must be brought low while the SCK pin is low. To
resume serial communication, the HOLD pin is brought
high while the SCK pin is low (SCK may still toggle during
HOLD). Inputs to the SI pin will be ignored while the SO pin
is in the high impedance state.
WRITE PROTECT: The write protect pin (WP) will allow
normal read/write operations when held high. When the
WP pin is brought low and WPEN bit is “1”, all write opera-
6
AT25080/160/320/640
tions to the status register are inhibited. WP going low
while CS is still low will interrupt a write to the status register. If the internal write cycle has already been initiated, WP
going low will have no effect on any write operation to the
status register. The WP pin function is blocked when the
WPEN bit in the status register is "0". This will allow the
user to install the AT25080/160/320/640 in a system with
the WP pin tied to ground and still be able to write to the
status register. All WP pin functions are enabled when the
WPEN bit is set to “1”.
SPI Serial Interface
AT25080/160/320/640
Functional Description
Table 3. Read Status Register Bit Definition
The AT25080/160/320/640 is designed to interface directly
with the synchronous serial peripheral interface (SPI) of the
6805 and 68HC11 series of microcontrollers.
The AT25080/160/320/640 utilizes an 8 bit instruction register. The list of instructions and their operation codes are
contained in Table 1. All instructions, addresses, and data
are transferred with the MSB first and start with a high-tolow CS transition.
Table 1. Instruction Set for the AT25080/160/320/640
Bit
Definition
Bit 0 (RDY)
Bit 0 = 0 (RDY) indicates the device is READY. Bit
0 = 1 indicates the write cycle is in progress.
Bit 1 (WEN)
Bit 1= 0 indicates the device is not WRITE
ENABLED. Bit 1 = 1 indicates the device is WRITE
ENABLED.
Bit 2 (BP0)
See Table 3.
Bit 3 (BP1)
See Table 3.
Bits 4-6 are 0s when device is not in an internal write cycle.
Instruction
Name
Instruction
Format
Operation
Bit 7 (WPEN)
WREN
0000 X110
Set Write Enable Latch
Bits 0-7 are 1s during an internal write cycle.
WRDI
0000 X100
Reset Write Enable Latch
RDSR
0000 X101
Read Status Register
WRSR
0000 X001
Write Status Register
READ
0000 X011
Read Data from Memory Array
WRITE
0000 X010
Write Data to Memory Array
WRITE ENABLE (WREN): The device will power up in the
write disable state when VCC is applied. All programming
instructions must therefore be preceded by a Write Enable
instruction.
WRITE DISABLE (WRDI): To protect the device against
inadvertent writes, the Write Disable instruction disables all
programming modes. The WRDI instruction is independent
of the status of the WP pin.
READ STATUS REGISTER (RDSR): The Read Status
Register instruction provides access to the status register.
The READY/BUSY and Write Enable status of the device
can be determined by the RDSR instruction. Similarly, the
Block Write Protection bits indicate the extent of protection
employed. These bits are set by using the WRSR instruction.
See Table 4.
WRITE STATUS REGISTER (WRSR): The WRSR instruction allows the user to select one of four levels of protection. The AT25080/160/320/640 is divided into four array
segments. One quarter (1/4), one half (1/2), or all of the
memory segments can be protected. Any of the data within
any selected segment will therefore be READ only. The
block write protection levels and corresponding status register control bits are shown in Table 4.
The three bits, BP0, BP1, and WPEN are nonvolatile cells
that have the same properties and functions as the regular
memory cells (e.g. WREN, tWC, RDSR).
Table 4. Block Write Protect Bits
Status
Register
Bits
Level
BP1
BP0
AT25080
AT25160
AT25320
AT25640
0
0
0
None
None
None
None
1(1/4)
0
1
0300
-03FF
0600
-07FF
0C00
-0FFF
1800
-1FFF
2(1/2)
1
0
0200
-03FF
0400
-07FF
0800
-0FFF
1000
-1FFF
3(All)
1
1
0000
-03FF
0000
-07FF
0000
-0FFF
0000
-1FFF
Table 2. Status Register Format
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WPEN
X
X
X
BP1
BP0
WEN
RDY
Array Addresses Protected
The WRSR instruction also allows the user to enable or
disable the write protect (WP) pin through the use of the
Write Protect Enable (WPEN) bit. Hardware write protection is enabled when the WP pin is low and the WPEN bit is
“1”. Hardware write protection is disabled when either the
WP pin is high or the WPEN bit is “0”. When the device is
hardware write protected, writes to the Status Register,
including the Block Protect bits and the WPEN bit, and the
block-protected sections in the memory array are disabled.
7
Writes are only allowed to sections of the memory which
are not block-protected.
NOTE: When the WPEN bit is hardware write protected, it
cannot be changed back to “0”, as long as the WP pin is
held low.
Table 5. WPEN Operation
WPEN
WP
WEN
Protected
Blocks
Unprotected
Blocks
Status
Register
0
X
0
Protected
Protected
Protected
0
X
1
Protected
Writable
Writable
1
Low
0
Protected
Protected
Protected
1
Low
1
Protected
Writable
Protected
X
High
0
Protected
Protected
Protected
X
High
1
Protected
Writable
Writable
READ SEQUENCE (READ): Reading the
AT25080/160/320/640 via the SO (Serial Output) pin
requires the following sequence. After the CS line is pulled
low to select a device, the READ op-code is transmitted via
the SI line followed by the byte address to be read (A15-A0,
Refer to Table 6). Upon completion, any data on the SI line
will be ignored. The data (D7-D0) at the specified address
is then shifted out onto the SO line. If only one byte is to be
read, the CS line should be driven high after the data
comes out. The READ sequence can be continued since
the byte address is automatically incremented and data will
continue to be shifted out. When the highest address is
reached, the address counter will roll over to the lowest
address allowing the entire memory to be read in one continuous READ cycle.
WRITE SEQUENCE (WRITE): In order to program the
AT25080/160/320/640, two separate instructions must be
executed. First, the device must be write enabled via the
Write Enable (WREN) Instruction. Then a Write (WRITE)
Instruction may be executed. Also, the address of the
8
AT25080/160/320/640
memory location(s) to be programmed must be outside the
protected address field location selected by the Block Write
Protection Level. During an internal write cycle, all commands will be ignored except the RDSR instruction.
A Write Instruction requires the following sequence. After
the CS line is pulled low to select the device, the WRITE
op-code is transmitted via the SI line followed by the byte
address (A15-A0) and the data (D7-D0) to be programmed
(Refer to Table 6). Programming will start after the CS pin
is brought high. (The LOW to High transition of the CS pin
must occur during the SCK low time immediately after
clocking in the D0 (LSB) data bit.
The READY/BUSY status of the device can be determined
by initiating a READ STATUS REGISTER (RDSR) Instruction. If Bit 0 = 1, the WRITE cycle is still in progress. If Bit 0
= 0, the WRITE cycle has ended. Only the READ STATUS
REGISTER instruction is enabled during the WRITE programming cycle.
The AT25080/160/320/640 is capable of a 32-byte PAGE
WRITE operation. After each byte of data is received, the
five low order address bits are internally incremented by
one; the high order bits of the address will remain constant.
If more than 32-bytes of data are transmitted, the address
counter will roll over and the previously written data will be
overwritten. The AT25080/160/320/640 is automatically
returned to the write disable state at the completion of a
WRITE cycle.
NOTE: If the device is not Write enabled (WREN), the
device will ignore the Write instruction and will return to the
standby state, when CS is brought high. A new CS falling
edge is required to re-initiate the serial communication.
Table 6. Address Key
Address
AT25080
AT25160
AT25320
AT25640
AN
A9 - A0
A10 - A0
A11 - A0
A12 - A0
Don't
Care Bits
A15 - A10
A15 - A11
A15 - A12
A15 - A13
AT25080/160/320/
Timing Diagrams
Synchronous Data Timing (for Mode 0)
t CS
VIH
CS
VIL
t CSH
t CSS
VIH
t WH
SCK
t WL
VIL
tH
t SU
VIH
SI
VALID IN
VIL
tV
VOH
SO
HI-Z
t HO
t DIS
HI-Z
VOL
WREN Timing
WRDI Timing
9
RDST Timing
CS
0
1
2
3
4
5
6
7
8
9
7
6
10
11
12
13
14
2
1
SCK
INSTRUCTION
SI
SO
DATA OUT
HIGH IMPEDANCE
5
4
3
0
MSB
WRSR Timing
CS
0
1
2
3
4
5
6
7
8
9
10
7
6
5
11
12
13
14
15
DATA IN
4
3
2
1
0
SCK
SI
SO
INSTRUCTION
HIGH IMPEDANCE
READ Timing
CS
0 1 2 3 4 5 6 7 8 9 10 11 20 21 22 23 24 25 26 27 28 29 30
SCK
SI
SO
10
INSTRUCTION
HIGH IMPEDANCE
AT25080/160/320/
BYTE ADDRESS
15 14 13 ... 3 2 1 0
DATA OUT
7 6 5 4 3 2 1 0
MSB
AT25080/160/320/640
WRITE Timing
CS
0 1 2 3 4 5 6 7 8 9 10 11 20 21 22 23 24 25 26 27 28 29 30 31
SCK
SI
SO
BYTE ADDRESS
15 14 13 ... 3 2 1 0
INSTRUCTION
DATA IN
7 6 5 4 3 2 1 0
HIGH IMPEDANCE
HOLD Timing
CS
tCD
tCD
SCK
t HD
t HD
HO LD
t HZ
SO
t LZ
11
AT25080 Ordering Information
tWC (max)
(ms)
ICC (max)
(µ
µA)
ISB (max)
(µ
µA)
fMAX
(kHz)
5
5000
2.0
10
3000
20
Ordering Code
Package
2100
AT25080-10PC
AT25080N-10SC
AT25080T1-10TC
8P3
8S1
14T
Commercial
(0°C to 70°C)
0.5
2100
AT25080-10PC-2.7
AT25080N-10SC-2.7
AT25080T1-10TC-2.7
8P3
8S1
14T
Commercial
(0°C to 70°C)
3000
0.2
500
AT25080-10PC-1.8
AT25080N-10SC-1.8
AT25080T1-10TC-1.8
8P3
8S1
14T
Commercial
(0°C to 70°C)
5
5000
2.0
2100
AT25080-10PI
AT25080N-10SI
AT25080T1-10TI
8P3
8S1
14T
Industrial
(-40°C to 85°C)
10
3000
0.5
2100
AT25080-10PI-2.7
AT25080N-10SI-2.7
AT25080T1-10TI-2.7
8P3
8S1
14T
Industrial
(-40°C to 85°C)
20
3000
0.2
500
AT25080-10PI-1.8
AT25080N-10SI-1.8
AT25080T1-10TI-1.8
8P3
8S1
14T
Industrial
(-40°C to 85°C)
Package Type
8P3
8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S1
8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
14T
14-Lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP)
Options
Blank
Standard Device (4.5V to 5.5V)
-2.7
Low Voltage (2.7V to 5.5V)
-1.8
Low Voltage (1.8V to 3.6V)
12
AT25080/160/320/640
Operation Range
AT25080/160/320/640
AT25160 Ordering Information
tWC (max)
(ms)
ICC (max)
(µ
µA)
ISB (max)
(µ
µA)
fMAX
(kHz)
5
5000
2.0
10
3000
20
Ordering Code
Package
Operation Range
2100
AT25160-10PC
AT25160N-10SC
AT25160T1-10TC
8P3
8S1
14T
Commercial
(0°C to 70°C)
0.5
2100
AT25160-10PC-2.7
AT25160N-10SC-2.7
AT25160T1-10TC-2.7
8P3
8S1
14T
Commercial
(0°C to 70°C)
3000
0.2
500
AT25160-10PC-1.8
AT25160N-10SC-1.8
AT25160T1-10TC-1.8
8P3
8S1
14T
Commercial
(0°C to 70°C)
5
5000
2.0
2100
AT25160-10PI
AT25160N-10SI
AT25160T1-10TI
8P3
8S1
14T
Industrial
(-40°C to 85°C)
10
3000
0.5
2100
AT25160-10PI-2.7
AT25160N-10SI-2.7
AT25160T1-10TI-2.7
8P3
8S1
14T
Industrial
(-40°C to 85°C)
20
3000
0.2
500
AT25160-10PI-1.8
AT25160N-10SI-1.8
AT25160T1-10TI-1.8
8P3
8S1
14T
Industrial
(-40°C to 85°C)
Package Type
8P3
8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S1
8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
14T
14-Lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP)
Options
Blank
Standard Device (4.5V to 5.5V)
-2.7
Low Voltage (2.7V to 5.5V)
-1.8
Low Voltage (1.8V to 3.6V)
13
AT25320 Ordering Information
tWC (max)
(ms)
ICC (max)
(µ
µA)
ISB (max)
(µ
µA)
fMAX
(kHz)
5
5000
2.0
10
3000
20
Ordering Code
Package
2100
AT25320-10PC
AT25320N-10SC
AT25320T1-10TC
AT25320T2-10TC
8P3
8S1
14T
20T
Commercial
(0°C to 70°C)
0.5
2100
AT25320-10PC-2.7
AT25320N-10SC-2.7
AT25320T1-10TC-2.7
AT25320T2-10TC-2.7
8P3
8S1
14T
20T
Commercial
(0°C to 70°C)
3000
0.2
500
AT25320-10PC-1.8
AT25320N-10SC-1.8
AT25320T1-10TC-1.8
AT25320T2-10TC-1.8
8P3
8S1
14T
20T
Commercial
(0°C to 70°C)
5
5000
2.0
2100
AT25320-10PI
AT25320N-10SI
AT25320T1-10TI
AT25320T2-10TI
8P3
8S1
14T
20T
Industrial
(-40°C to 85°C)
10
3000
0.5
2100
AT25320-10PI-2.7
AT25320N-10SI-2.7
AT25320T1-10TI-2.7
AT25320T2-10TI-2.7
8P3
8S
14T
20T
Industrial
(-40°C to 85°C)
20
3000
0.2
500
AT25320-10PI-1.8
AT25320N-10SI-1.8
AT25320T1-10TI-1.8
AT25320T2-10TI-1.8
8P3
8S1
14T
20T
Industrial
(-40°C to 85°C)
Package Type
8P3
8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S1
8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
14T
14-Lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP)
20T
20-Lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP)
Options
Blank
Standard Device (4.5V to 5.5V)
-2.7
Low Voltage (2.7V to 5.5V)
-1.8
Low Voltage (1.8V to 3.6V)
14
AT25080/160/320/640
Operation Range
AT25080/160/320/640
AT25640 Ordering Information
tWC (max)
(ms)
ICC (max)
(µ
µA)
ISB (max)
(µ
µA)
fMAX
(kHz)
5
5000
2.0
10
3000
20
Ordering Code
Package
Operation Range
2100
AT25640-10PC
AT25640N-10SC
AT25640T1-10TC
AT25640T2-10TC
8P3
8S1
14T
20T
Commercial
(0°C to 70°C)
0.5
2100
AT25640-10PC-2.7
AT25640N-10SC-2.7
AT25640T1-10TC-2.7
AT25640T2-10TC-2.7
8P3
8S1
14T
20T
Commercial
(0°C to 70°C)
3000
0.2
500
AT25640-10PC-1.8
AT25640N-10SC-1.8
AT25640T1-10TC-1.8
AT25640T2-10TC-1.8
8P3
8S1
14T
20T
Commercial
(0°C to 70°C)
5
5000
2.0
2100
AT25640-10PI
AT25640N-10SI
AT25640T1-10TI
AT25640T2-10TI
8P3
8S1
14T
20T
Industrial
(-40°C to 85°C)
10
3000
0.5
2100
AT25640-10PI-2.7
AT25640N-10SI-2.7
AT25640T1-10TI-2.7
AT25640T2-10TI-2.7
8P3
8S1
14T
20T
Industrial
(-40°C to 85°C)
20
3000
0.2
500
AT25640-10PI-1.8
AT25640N-10SI-1.8
AT25640T1-10TI-1.8
AT25640T2-10TI-1.8
8P3
8S1
14T
20T
Industrial
(-40°C to 85°C)
Package Type
8P3
8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S1
8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
14T
14-Lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP)
20T
20-Lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP)
Options
Blank
Standard Device (4.5V to 5.5V)
-2.7
Low Voltage (2.7V to 5.5V)
-1.8
Low Voltage (1.8V to 3.6V)
15
Packaging Information
8P3, 8-Lead, 0.300" Wide,
Plastic Dual Inline Package (PDIP)
Dimensions in Inches and (Millimeters)
8S1, 8-Lead, 0.150" Wide,
Plastic Gull Wing Small Outline (JEDEC SOIC)
Dimensions in Inches and (Millimeters)
JEDEC STANDARD MS-001 BA
.400 (10.16)
.355 (9.02)
.020 (.508)
.013 (.330)
PIN
1
.280 (7.11)
.240 (6.10)
.157 (3.99)
.150 (3.81)
PIN 1
.244 (6.20)
.228 (5.79)
.037 (.940)
.027 (.690)
.300 (7.62) REF
.050 (1.27) BSC
.210 (5.33) MAX
.100 (2.54) BSC
.196 (4.98)
.189 (4.80)
SEATING
PLANE
.068 (1.73)
.053 (1.35)
.015 (.380) MIN
.150 (3.81)
.115 (2.92)
.022 (.559)
.014 (.356)
.070 (1.78)
.045 (1.14)
.010 (.254)
.004 (.102)
.325 (8.26)
.300 (7.62)
0
REF
8
0
REF
15
.012 (.305)
.008 (.203)
.050 (1.27)
.016 (.406)
.430 (10.9) MAX
14T, 14-Lead, 0.170" Wide,
Thin Super Small Outline Package (TSSOP)
Dimensions in Inches and (Millimeters)
.010 (.254)
.007 (.203)
20T, 20-Lead, 0.170" Wide,
Thin Super Small Outline Package (TSSOP)
Dimensions in Inches and (Millimeters)
INDEX MARK
INDEX MARK
PIN
1
PIN
1
4.50 (.177)
4.30 (.169)
5.10 (.201)
4.90 (.193)
.650 (.026) BSC
SEATING
PLANE
0.20 (.008)
0.09 (.004)
0
REF
8
0.75 (.030)
0.45 (.018)
16
4.50 (.177)
4.30 (.169)
6.60 (.260)
6.40 (.252)
1.20 (.047) MAX
0.15 (.006)
0.05 (.002)
0.30 (.012)
0.19 (.007)
6.50 (.256)
6.25 (.246)
AT25080/160/320/640
.650 (.026) BSC
1.20 (.047) MAX
0.15 (.006)
0.05 (.002)
0.30 (.012)
0.19 (.007)
0.20 (.008)
0.09 (.004)
0
REF
8
0.75 (.030)
0.45 (.018)
6.50 (.256)
6.25 (.246)
SEATING
PLANE
Similar pages