Kingbright AT5050QB10ZS-RV 5.0x5.0mm smd led with ceramic substrate Datasheet

5.0X5.0mm SMD LED WITH CERAMIC SUBSTRATE
PRELIMINARY SPEC
Part Number: AT5050QB10ZS-RV
Blue
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
1.Dimensions : 5.0mm X 5.0mm X 1.0mm.
2.Higher brightness .
3.Small package with high efficiency .
4.Surface mount technology .
5.ESD protection .
6.Moisture sensitivity level : level 2a.
Material as follows:
7.Compatible with IR-reflow processes.
Package : Ceramics
8.RoHS compliant.
Encapsulating resin : Silicone resin
Electrodes : Ag plating
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Specifications are subject to change without notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAI5832
REV NO: V.1
DATE: SEP/22/2008
PAGE: 1 OF 10
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.F.Lu
ERP: 1212000025
5.0X5.0mm SMD LED WITH CERAMIC SUBSTRATE
Selection Guide
Dice
Part No.
AT5050QB10ZS-RV
Viewing
Angle [1]
Φv (lm) [2]
@ 350mA
Code.
Min.
Max.
CB-L
5
10
CC-L
10
15
CD-L
15
20
CE-L
20
25
2θ1/2
120°
Blue (InGaAlN)
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
2. Luminous intensity / luminous flux: +/-15%.
Absolute Maximum Ratings at TA = 25°C
Parameter
Symbol
Value
Unit
IF
350
mA
Peak Forward Current [2]
IFM
500
mA
Power dissipation
Pt
1.25
W
Operating Temperature
Top
-40 To +100
°C
Storage Temperature
Tstg
-40 To +120
°C
TJ
120
°C
Rth j-a
70
°C/W
Rth j-s
26
°C/W
DC Forward Current [1]
Junction temperature[1]
Thermal resistance [1]
(Junction/ambient)
Thermal resistance [1] (Junction/solder point)
Notes:
1. Results from mounting on PC board FR4 (pad size>100mm2 ) , mounted on pc board-metal core PCB is recommend
for lowest thermal resistance.
2. 1/10 Duty Cycle, 0.1ms Pulse Width.
Electrical / Optical Characteristics at TA = 25°C
Parameter
Symbol
Forward Voltage IF = 350mA [Min.]
Value
Unit
2.8
VF [2]
Forward Voltage IF = 350mA [Typ.]
Forward Voltage IF = 350mA [Max.]
3.2
V
3.6
Luminous Flux IF = 350mA [Typ.]
Φv
15
lm
λpeak
452
nm
λ dom [1]
458
nm
Spectral bandwidth at 50% ΦREL MAX IF = 350mA [Typ.]
Δλ
20
nm
Temperature coefficient of λpeak
IF = 350mA, - 10°C ≤ T ≤ 100°C [Typ.]
TCλpeak
0.2
nm/°C
Temperature coefficient of λdom
IF = 350mA, - 10°C ≤ T ≤ 100°C [Typ.]
TCλdom
0.1
nm/°C
Temperature coefficient of VF
IF = 350mA, - 10°C ≤ T≤ 100°C [Typ.]
TCV
-3.2
mV/°C
Wavelength at peak emission IF = 350mA
Dominant Wavelength IF = 350mA
[Typ.]
[Typ.]
Notes:
1.Wavelength : + / -1nm.
2. Forward Voltage : + / - 0.1V.
SPEC NO: DSAI5832
REV NO: V.1
DATE: SEP/22/2008
PAGE: 2 OF 10
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.F.Lu
ERP: 1212000025
5.0X5.0mm SMD LED WITH CERAMIC SUBSTRATE
Blue
AT5050QB10ZS-RV
SPEC NO: DSAI5832
REV NO: V.1
DATE: SEP/22/2008
PAGE: 3 OF 10
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.F.Lu
ERP: 1212000025
5.0X5.0mm SMD LED WITH CERAMIC SUBSTRATE
SPEC NO: DSAI5832
REV NO: V.1
DATE: SEP/22/2008
PAGE: 4 OF 10
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.F.Lu
ERP: 1212000025
5.0X5.0mm SMD LED WITH CERAMIC SUBSTRATE
Recommended Soldering Pattern
(Units : mm ; Tolerance: ± 0.1)
Tape Dimensions
(Units : mm)
Reel Dimension
SPEC NO: DSAI5832
REV NO: V.1
DATE: SEP/22/2008
PAGE: 5 OF 10
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.F.Lu
ERP: 1212000025
5.0X5.0mm SMD LED WITH CERAMIC SUBSTRATE
Packing & Label Specifications
AT5050QB10ZS-RV
Packaging:
1.The LEDs are packed in cardboard boxes after taping.
2.The label on the minimum packing unit shows: Part Number, Lot Number, Ranking, Quantity.
3.In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation.
4.The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions
must be taken to prevent any damage.
5.The boxes are not water resistant and therefore must be kept away from water and moisture.
6.When the LEDs are transported, we recommend that you use the same packing methods as Kingbright’s.
SPEC NO: DSAI5832
REV NO: V.1
DATE: SEP/22/2008
PAGE: 6 OF 10
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.F.Lu
ERP: 1212000025
5.0X5.0mm SMD LED WITH CERAMIC SUBSTRATE
JEDEC Moisture Sensitivity:
Time
2a
Soak Requirements
Floor Life
Level
Standard
Conditions
≤ 30 °C / 60% RH
4 weeks
Time (hours)
Time (hours)
Conditions
30 °C / 60% RH
120
+1/-0
60 °C / 60% RH
2
696
+5/-0
Accelerated Equivalent
Conditions
Notes:
1. CAUTION - The ‘‘accelerated equivalent’’ soak requirements shall not be used until correlation of damage response, including electrical, after
soak and reflow is established with the ‘‘standard’’ soak requirements or if the known activation energy for diffusion is 0.4 - 0.48 eV. Accelerated
soak times may vary due to material properties, e.g., mold compound, encapsulant, etc. JEDEC document JESD22-A120 provides a method for
determining the diffusion coefficient.
2. The standard soak time includes a default value of 24 hours for semiconductor manufacturer’s exposure time (MET) between bake and bag and
includes the maximum time allowed out of the bag at the distributor’s facility.
If the actual MET is less than 24 hours the soak time may be reduced. For soak conditions of 30 °C/60% RH the soak time is reduced by one hour
For each hour the MET is less than 24 hours. For soak conditions of 60 °C/60% RH, the soak time is reduced by one hour for each five hours the
MET is less than 24 hours.
If the actual MET is greater than 24 hours the soak time must be increased. If soak conditions are 30 °C/60% RH, the soak time is increased one
Hour for each hour that the actual MET exceeds 24 hours. If soak conditions are 60 °C/60% RH, the soak time is increased one hour for each five
Hours that the actual MET exceeds 24 hours.
3. Supplier may extend the soak times at their own risk.
ESD Protection During Production
Electric static discharge can result when static-sensitive products come in contact with the operator or other conductors.
The following procedures may decrease the possibility of ESD damage:
1.Minimize friction between the product and surroundings to avoid static buildup.
2.All production machinery and test instruments must be electrically grounded.
3.Operators must wear anti-static bracelets.
4.Wear anti-static suit when entering work areas with conductive machinery.
5.Set up ESD protection areas using grounded metal plating for component handling.
6.All workstations that handle IC and ESD-sensitive components must maintain an electrostatic potential of 150V or less.
7.Maintain a humidity level of 50% or higher in production areas.
8.Use anti-static packaging for transport and storage.
9.All anti-static equipment and procedures should be periodically inspected and evaluated for proper functionality.
Heat Generation:
1.Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making
the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the
circuit board and density of LED placement on the board ,as well as other components. It is necessary to avoid intense heat
generation and operate within the maximum ratings given in this specification.
2.Please determine the operating current with consideration of the ambient temperature local to the LED and refer to the plot
of Permissible Forward current vs. Ambient temperature on CHARACTERISTICS in this specification. Please also take meas
ures to remove heat from the area near the LED to improve the operational characteristics on the LED.
3.The equation ① indicates correlation between Tj and Ta ,and the equation ② indicates correlation between Tj and Ts
Tj = Ta + Rthj-a *W ………
①
Tj = Ts + Rthj-s *W ………
②
Tj = dice junction temperature: °C
Ta = ambient temperature:°C
Ts = solder point temperature:°C
Rthj-a = heat resistance from dice junction temperature to ambient temperature : °C/ W
Rthj-s = heat resistance from dice junction temperature to Ts measuring point : °C/ W
W = inputting power (IFx VF) : W
SPEC NO: DSAI5832
REV NO: V.1
DATE: SEP/22/2008
PAGE: 7 OF 10
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.F.Lu
ERP: 1212000025
5.0X5.0mm SMD LED WITH CERAMIC SUBSTRATE
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might leads to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter
of the nozzle should be as large as possible.
5. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
6. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
SPEC NO: DSAI5832
REV NO: V.1
DATE: SEP/22/2008
PAGE: 8 OF 10
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.F.Lu
ERP: 1212000025
5.0X5.0mm SMD LED WITH CERAMIC SUBSTRATE
Designing the Position of LED on a Board.
1.No twist/warp/bent/or other stress shall be applied to the board after mounting LED with
solder to avoid a crack of LED package.
Refer to the following recommended position and direction of LED.
Appropriate LED mounting is to place perpendicularly against the stress affected side.
2.Depending on the position and direction of LED,the mechanical stress on the LED package can be changed.
Refer to the following figure.
3.Do not split board by hand.Split with exclusive special tool.
4.If an aluminum circuit board is used,a large stress by thermal shock might cause a solder crack.
For this reason,it is recommended an appropriate verification should be taken before use.
SPEC NO: DSAI5832
REV NO: V.1
DATE: SEP/22/2008
PAGE: 9 OF 10
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.F.Lu
ERP: 1212000025
5.0X5.0mm SMD LED WITH CERAMIC SUBSTRATE
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below
Lot Tolerance Percent Defective (LTPD) : 10%
No.
Test Item
Test Conditions
Test Times /
Cycles
Number of Damaged
1
Continuous Operating Test
Ta = 25 °C , IF = 350 mA
Tested with standard circuit board﹡
1000 hrs
0/22
2
High Temperature Operating Test
Ta = 100 °C , IF = 60 mA (note)
1000 hrs
0/22
3
Low Temperature Operating Test
Ta = -40 °C , IF = 350 mA
Tested with standard circuit board﹡
1000 hrs
0/22
4
High Temperature and Humidity
Storage Operating Test
Ta = 85 °C , RH = 85% , IF = 110 mA
(note)
1000 hrs
0/22
5
Temperature Cycling Test
High temp: +100 °C 30 mins
∫
R.T : 5 mins
∫
Low temp : -40 °C 30 mins
∫
R.T : 5 mins
10 cycles
0/22
6
Thermal Shock Test
High temp : +100 °C 5 mins
∫
Low temp : -40 °C 5 mins
100 cycles
0/22
7
Soldering resistance Test
Tsld = 260 °C , 10 secs
10 secs
0/22
Note : Thermal resistance of LED with Kingbright circuit board : Rthj-a = 70°C/W
Failure Criteria
Item
Symbol
Test Conditions
Forward Voltage
VF
Luminous Flux
Φv
Criteria for Judgement
Min.
Max.
IF = 350mA
-
Initial Level x 1.1
IF = 350mA
Initial Level x 0.7
-
Note : The test is performed after the board is cooled down to the room temperature.
SPEC NO: DSAI5832
REV NO: V.1
DATE: SEP/22/2008
PAGE: 10 OF 10
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.F.Lu
ERP: 1212000025
Similar pages