PHILIPS AV16821DL 20-bit bus-interface d-type flip-flop; positive-edge trigger 3-state Datasheet

INTEGRATED CIRCUITS
74ALVT16821
20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
Product specification
Supersedes data of 1997 May 01
IC24 Data Handbook
1998 Feb 13
Philips Semiconductors
Product specification
2.5V/3.3V 20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
FEATURES
74ALVT16821
DESCRIPTION
• 20-bit positive-edge triggered register
• 5V I/O Compatible
• Multiple VCC and GND pins minimize switching noise
• Live insertion/extraction permitted
• Power-up reset
• Power-up 3-State
• Output capability: +64mA/-32mA
• Latch-up protection exceeds 500mA per Jedec Std 17
• ESD protection exceeds 2000V per MIL STD 883 Method 3015
The 74ALVT16821 high-performance BiCMOS device combines
low static and dynamic power dissipation with high speed and high
output drive. It is designed for VCC operation at 2.5V or 3.3V with I/O
compatibility to 5V.
The 74ALVT16821 has two 10-bit, edge triggered registers, with
each register coupled to a 3-State output buffer. The two sections of
each register are controlled independently by the clock (nCP) and
Output Enable (nOE) control gates.
Each register is fully edge triggered. The state of each D input, one
set-up time before the Low-to-High clock transition, is transferred to
the corresponding flip-flop’s Q output.
The 3-State output buffers are designed to drive heavily loaded
3-State buses, MOS memories, or MOS microprocessors.
and 200V per Machine Model
• Bus hold data inputs eliminate the need for external pull-up
The active Low Output Enable (nOE) controls all ten 3-State buffers
independent of the register operation. When nOE is Low, the data in
the register appears at the outputs. When nOE is High, the outputs
are in high impedance “off” state, which means they will neither drive
nor load the bus.
resistors to hold unused inputs
QUICK REFERENCE DATA
SYMBOL
CONDITIONS
Tamb = 25°C
PARAMETER
TYPICAL
UNIT
2.5V
3.3V
2.6
2.7
1.7
1.8
ns
tPLH
tPHL
Propagation delay
nCP to nQ
CL = 50pF
CIN
Input capacitance
VI = 0V or VCC
3
3
pF
COUT
Output capacitance
VO = 0 or VCC
9
9
pF
ICCZ
Total supply current
Outputs disabled
40
70
µA
ORDERING INFORMATION
PACKAGES
TEMPERATURE RANGE
OUTSIDE NORTH AMERICA
NORTH AMERICA
DWG NUMBER
56-Pin Plastic SSOP Type III
–40°C to +85°C
74ALVT16821 DL
AV16821 DL
SOT371-1
56-Pin Plastic TSSOP Type II
–40°C to +85°C
74ALVT16821 DGG
AV16821 DGG
SOT364-1
1998 Feb 13
2
853-1869 18962
Philips Semiconductors
Product specification
2.5V/3.3V 20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
LOGIC SYMBOL
56
54
74ALVT16821
PIN CONFIGURATION
52
51
49
48
47
1D0 1D1 1D2 1D3 1D4 1D5 1D6
45
44
43
1D7 1D8
1D9
1OE
1
56
1CP
1Q0
2
55
1D0
56
1CP
1Q1
3
54
1D1
1
1OE
GND
4
53
GND
1Q2
5
52
1D2
1Q3
6
51
1D3
VCC
7
50
VCC
1Q4
8
49
1D4
1Q5
9
48
1D5
1Q6
10
47
1D6
GND
11
46
GND
1Q7
12
45
1D7
1Q8
13
44
1D8
1Q9
14
43
1D9
2Q0
15
42
2D0
2Q1
16
41
2D1
2Q2
17
40
2D2
GND
18
39
GND
2Q3
19
38
2D3
2Q4
20
37
2D4
2Q5
21
36
2D5
VCC
22
35
VCC
2Q6
23
34
2D6
2Q7
24
33
2D7
1Q0 1Q1 1Q2 1Q3 1Q4 1Q5 1Q6 1Q7 1Q8 1Q9
2
3
42
41
5
40
6
38
8
37
9
36
10
34
2D0 2D1 2D2 2D3 2D4 2D5 2D6
29
12
33
13
14
31
30
2D7 2D8
2D9
2CP
28
2OE
2Q0 2Q1 2Q2 2Q3 2Q4 2Q5 2Q6 2Q7 2Q8 2Q9
15
16
17
19
20
21
23
24
26
27
SH00002
LOGIC SYMBOL (IEEE/IEC)
1OE
1
1CP
56
2OE
28
2CP
29
1D0
55
1D1
EN2
C1
EN4
C3
2
1Q0
GND
25
32
GND
54
3
1Q1
2Q8
26
31
2D8
1D2
52
5
1Q2
2Q9
27
30
2D9
1D3
51
6
1Q3
2OE
28
29
2CP
1D4
49
8
1Q4
1D5
48
9
1Q5
1D6
47
10
1Q6
1D7
45
12
1Q7
1D8
44
13
1Q8
1D9
43
14
1Q9
2D0
42
15
2Q0
2D1
41
16
2Q1
2D2
40
17
2Q2
2D3
38
19
2Q3
2D4
37
20
2Q4
2D5
36
21
2Q5
2D6
34
23
2Q6
2D7
33
24
2Q7
2D8
31
26
2Q8
2D9
30
27
2Q9
1D
3D
2∇
4∇
SH00001
SH00003
1998 Feb 13
3
Philips Semiconductors
Product specification
2.5V/3.3V 20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
PIN DESCRIPTION
PIN NUMBER
FUNCTION TABLE
SYMBOL
56, 54, 52, 51, 49,
48, 47, 45, 44, 43,
42, 41, 40, 38, 37,
36, 34, 33, 31, 30
74ALVT16821
INPUTS
FUNCTION
1D0 - 1D9
2D0 - 2D9
Data inputs
2, 3, 5, 6, 8, 9, 10,
12, 13, 14,
15, 16, 17, 19, 20,
21, 23, 24, 26, 27
1Q0 - 1Q9
2Q0 - 2Q9
Data outputs
1, 28
1OE, 2OE
Output enable inputs
(active-Low)
56, 29
1CP, 2CP
Clock pulse inputs
(active rising edge)
4, 11, 18, 25, 32,
39, 46, 53
GND
Ground (0V)
7, 22, 35, 50
VCC
Positive supply
voltage
OUTPUTS
nQ0 - nQ9
OPERATING
MODE
nOE
nCP
nDx
INTERNAL
REGISTER
L
L
↑
↑
l
h
L
H
L
H
Load and read
register
L
↑
X
NC
NC
Hold
H
↑
X
NC
Z
Disable
↑
H
Dn
Dn
Z
outputs
H = High voltage level
h = High voltage level one set-up time prior to the Low-to-High
clock transition
L = Low voltage level
l = Low voltage level one set-up time prior to the Low-to-High
clock transition
NC= No change
X = Don’t care
Z = High impedance “off” state
↑ = Low to High clock transition
↑ = Not a Low-to-High clock transition
LOGIC DIAGRAM
nD0
nD1
nD2
nD3
nD4
nD5
nD6
nD7
nD8
nD9
D
D
D
D
D
D
D
D
D
D
CP Q
CP Q
CP Q
CP Q
CP Q
CP Q
CP Q
CP Q
CP Q
CP Q
nCP
nOE
nQ0
nQ1
nQ2
nQ3
nQ4
nQ5
nQ6
nQ7
nQ8
nQ9
SH00004
1998 Feb 13
4
Philips Semiconductors
Product specification
2.5V/3.3V 20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
74ALVT16821
ABSOLUTE MAXIMUM RATINGS1, 2
PARAMETER
SYMBOL
VCC
CONDITIONS
RATING
UNIT
–0.5 to +4.6
V
–50
mA
–1.2 to +7.0
V
VO < 0
–50
mA
Output in Off or High state
–0.5 to +7.0
V
Output in Low state
128
Output in High state
–64
DC supply voltage
IIK
DC input diode current
VI
DC input voltage3
IOK
DC output diode current
VI < 0
VOUT
DC output voltage3
IOUT
O
DC output current
Tstg
Storage temperature range
mA
°C
–65 to 150
NOTES:
1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to
absolute-maximum-rated conditions for extended periods may affect device reliability.
2. The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction
temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150°C.
3. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
VCC
2.5V RANGE LIMITS
PARAMETER
DC supply voltage
3.3V RANGE LIMITS
UNIT
MIN
MAX
MIN
MAX
2.3
2.7
3.0
3.6
V
0
5.5
0
5.5
V
VI
Input voltage
VIH
High-level input voltage
VIL
Input voltage
0.7
0.8
V
IOH
High-level output current
–8
–32
mA
Low-level output current
8
32
Low-level output current; current duty cycle ≤ 50%; f ≥ 1kHz
24
64
IOL
∆t/∆v
Input transition rise or fall rate; Outputs enabled
Tamb
Operating free-air temperature range
1998 Feb 13
1.7
2.0
10
–40
5
+85
–40
V
mA
10
ns/V
+85
°C
Philips Semiconductors
Product specification
2.5V/3.3V 20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
74ALVT16821
DC ELECTRICAL CHARACTERISTICS (3.3V 0.3V RANGE)
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
Temp = -40°C to +85°C
MIN
VIK
VOH
VOL
VRST
Input clamp voltage
VCC = 3.0V; IIK = –18mA
High-level out
output
ut voltage
output
Low–level out
ut voltage
Power-up output low
voltage6
VCC = 3.0 to 3.6V; IOH = –100µA
Input
In
ut leakage current
IHOLD
Off current
Data inputs7
–1.2
VCC
2.0
2.3
0.07
0.2
0.25
0.4
VCC = 3.0V; IOL = 32mA
0.3
0.5
VCC = 3.0V; IOL = 64mA
0.4
0.55
VCC = 3.6V; IO = 1mA; VI = VCC or GND
UNIT
V
V
VCC = 3.0V; IOL = 16mA
V
0.55
0.1
±1
VCC = 0 or 3.6V; VI = 5.5V
0.1
10
VCC = 3.6V; VI = VCC
0.5
1
0.1
-5
0.1
±100
Control pins
Data pins
ins4
VCC = 0V; VI or VO = 0 to 4.5V
Bus Hold current
–0.85
VCC = 3.0V; IOL = 100µA
VCC = 3.6V; VI = 0V
IOFF
MAX
VCC–0.2
VCC = 3.0V; IOH = –32mA
VCC = 3.6V; VI = VCC or GND
II
TYP1
VCC = 3V; VI = 0.8V
75
130
VCC = 3V; VI = 2.0V
–75
–140
VCC = 0V to 3.6V; VCC = 3.6V
±500
V
µA
µA
µA
Current into an output in the
High state when VO > VCC
VO = 5.5V; VCC = 3.0V
10
125
µA
Power up/down 3-State output
current3
VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC
OE/OE = Don’t care
1
±100
µA
IOZH
3-State output High current
VCC = 3.6V; VO = 3.0V; VI = VIL or VIH
0.5
5
µA
IOZL
3-State output Low current
VCC = 3.6V; VO = 0.5V; VI = VIL or VIH
0.5
–5
µA
VCC = 3.6V; Outputs High, VI = GND or VCC, IO = 0
0.07
0.1
IEX
IPU/PD
ICCH
ICCL
Quiescent supply current
ICCZ
∆ICC
Additional supply current per
input pin2
VCC = 3.6V; Outputs Low, VI = GND or VCC, IO = 0
5.1
7
VCC = 3.6V; Outputs Disabled; VI = GND or VCC, IO = 05
0.07
0.1
VCC = 3V to 3.6V; One input at VCC–0.6V,
Other inputs at VCC or GND
0.04
0.4
mA
mA
NOTES:
1. All typical values are at VCC = 3.3V and Tamb = 25°C.
2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND
3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.2V a
transition time of 100µsec is permitted. This parameter is valid for Tamb = 25°C only.
4. Unused pins at VCC or GND.
5. ICCZ is measured with outputs pulled up to VCC or pulled down to ground.
6. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power.
7. This is the bus hold overdrive current required to force the input to the opposite logic state.
AC CHARACTERISTICS (3.3V 0.3V RANGE)
GND = 0V; tR = tF = 2.5ns; CL = 50pF; RL = 500Ω; Tamb = –40°C to +85°C.
LIMITS
SYMBOL
PARAMETER
Tamb = –40 to +85oC
VCC = +3.3V
WAVEFORM
MIN
UNIT
TYP
MAX
1
0.5
0.5
1.7
1.8
3.2
3.5
ns
Output enable time
to High and Low level
3
4
1.0
0.5
2.1
1.4
3.5
2.4
ns
tPHZ
Output disable time
tPLZ
from High and Low level
NOTE:
1. All typical values are at VCC = 3.3V and Tamb = 25°C.
3
4
1.5
1.5
2.9
2.4
4.2
3.4
ns
fMAX
Maximum clock frequency
tPLH
tPHL
tPZH
tPZL
1998 Feb 13
1
150
Propagation delay
nCP to nQx
6
MHz
Philips Semiconductors
Product specification
2.5V/3.3V 20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
74ALVT16821
AC SETUP REQUIREMENTS (3.3V 0.3V RANGE)
GND = 0V, tR = tF = 2.5ns, CL = 50pF, RL = 500Ω
LIMITS
SYMBOL
PARAMETER
Tamb = -40 to +85oC
VCC = +3.3V ±0.3V
WAVEFORM
UNIT
MIN
TYP
2
1.5
1.5
0.1
0.1
ns
Hold time, High or Low
nDx to nCP
2
0.5
0.5
0.1
0.1
ns
nCP pulse width
High or Low
1
1.5
1.5
ts(H)
ts(L)
Setup time, High or Low
nDx to nCP
th(H)
th(L)
tw(H)
tw(L)
ns
DC ELECTRICAL CHARACTERISTICS (2.5V 0.2V RANGE)
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
Temp = -40°C to +85°C
MIN
VIK
Input clamp voltage
VOH
High-level out
output
ut voltage
VOL
Low-level output voltage
VCC = 2.3V; IIK = –18mA
VCC = 2.3 to 3.6V; IOH = –100µA
VCC = 2.3V; IOH = –8mA
TYP1
MAX
–0.85
–1.2
VCC–0.2
VCC
1.8
2.1
VRST
Power-up output low voltage7
0.07
0.2
VCC = 2.3V; IOL = 24mA
0.3
0.5
Input
In
ut leakage current
V
0.4
VCC = 2.7V; IO = 1mA; VI = VCC or GND
VCC = 2.7V; VI = VCC or GND
II
V
V
VCC = 2.3V; IOL = 100µA
VCC = 2.3V; IOL = 8mA
UNIT
0.55
Control pins
VCC = 0 or 2.7V; VI = 5.5V
VCC = 2.7V; VI = VCC
Data pins
ins4
VCC = 2.7V; VI = 0
0.1
±1
0.1
10
0.1
1
V
µA
0.1
-5
Off current
VCC = 0V; VI or VO = 0 to 4.5V
0.1
100
Bus Hold current
VCC = 2.3V; VI = 0.7V
90
Data inputs6
VCC = 2.3V; VI = 1.7V
–10
Current into an output in the
High state when VO > VCC
VO = 5.5V; VCC = 2.3V
10
125
µA
Power up/down 3-State output
current3
VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC
OE/OE = Don’t care
1
100
µA
IOZH
3-State output High current
VCC = 2.7V; VO = 2.3V; VI = VIL or VIH
0.5
5
µA
IOZL
3-State output Low current
VCC = 2.7V; VO = 0.5V; VI = VIL or VIH
0.5
–5
µA
VCC = 2.7V; Outputs High, VI = GND or VCC, IO = 0
0.04
0.1
VCC = 2.7V; Outputs Low, VI = GND or VCC, IO = 0
2.3
4.5
VCC = 2.7V; Outputs Disabled; VI = GND or VCC, IO = 05
0.04
0.1
VCC = 2.3V to 2.7V; One input at VCC–0.6V,
Other inputs at VCC or GND
0.04
0.4
IOFF
IHOLD
IEX
IPU/PD
ICCH
ICCL
Quiescent supply current
ICCZ
∆ICC
Additional supply current per
input pin2
µA
µA
mA
mA
NOTES:
1. All typical values are at VCC = 2.5V and Tamb = 25°C.
2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND
3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 2.5V ± 0.3V a
transition time of 100µsec is permitted. This parameter is valid for Tamb = 25°C only.
4. Unused pins at VCC or GND.
5. ICCZ is measured with outputs pulled up to VCC or pulled down to ground.
6. Not guaranteed.
7. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power.
1998 Feb 13
7
Philips Semiconductors
Product specification
2.5V/3.3V 20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
74ALVT16821
AC CHARACTERISTICS (2.5V "0.2V RANGE)
GND = 0V; tR = tF = 2.5ns; CL = 50pF; RL = 500Ω; Tamb = –40°C to +85°C.
LIMITS
SYMBOL
PARAMETER
Tamb = -40 to +85oC
VCC = +2.5V ±0.2V
WAVEFORM
MIN
UNIT
TYP
MAX
1
1.0
1.0
2.6
2.7
4.0
4.4
ns
Output enable time
to High and Low level
3
4
1.5
1.0
2.8
1.8
4.6
3.0
ns
tPHZ
Output disable time
tPLZ
from High and Low level
NOTE:
1. All typical values are at VCC = 3.3V and Tamb = 25°C.
3
4
1.5
1.0
2.7
2.1
4.1
3.3
ns
fMAX
Maximum clock frequency
1
150
tPLH
tPHL
Propagation delay
nCP to nQx
tPZH
tPZL
MHz
AC SETUP REQUIREMENTS (2.5V "0.2V RANGE)
GND = 0V, tR = tF = 2.5ns, CL = 50pF, RL = 500Ω
LIMITS
SYMBOL
PARAMETER
Tamb = -40 to +85oC
VCC = +2.5 ±0.2V
WAVEFORM
MIN
TYP
UNIT
ts(H)
ts(L)
Setup time, High or Low
nDx to nCP
2
1.5
2.0
0.1
0.5
ns
th(H)
th(L)
Hold time, High or Low
nDx to nCP
2
0.3
0.5
–0.5
–0.1
ns
tw(H)
tw(L)
nCP pulse width
High or Low
1
1.5
1.5
ns
AC WAVEFORMS
VM = 1.5V at VCC w 3.0V; VM = VCC/2 at VCC v 2.7V
VX = VOL + 0.3V at VCC w 3.0V; VX = VOL + 0.15V at VCC v 2.7V
VY = VOH – 0.3V at VCC w 3.0V; VY = VOH – 0.15V at VCC v 2.7V
nDx
1/fMAX
nCP
VM
tw(H)
VM
tw(L)
tPHL
nQx
3.0V or VCC
whichever
is less
VM
VM
VM
VM
VM
ts(H)
th(H)
ts(L)
th(L)
0V
CP
0V
tPLH
VM
VM
3.0V or VCC
whichever
is less
0V
VOH
VM
VM
VOL
SH00006
SH00005
Waveform 2. Data Setup and Hold Times
Waveform 1. Propagation Delay, Clock Input to Output,
Clock Pulse Width, and Maximum Clock frequency
1998 Feb 13
3.0V or VCC
whichever
is less
8
Philips Semiconductors
Product specification
2.5V/3.3V 20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
3.0V or VCC
whichever
is less
nOE
VM
VM
74ALVT16821
VM
VM
0V
0V
tPZH
tPZL
tPHZ
VM
tPLZ
3.0V or VCC
nQx
VOH
VM
VY
nQx
3.0V or VCC
whichever
is less
nOE
VX
VOL
0V
0V
SH00008
SH00007
Waveform 3. 3-State Output Enable Time to High Level
and Output Disable Time from High Level
Waveform 4. 3-State Output Enable Time to Low Level
and Output Disable Time from Low Level
TEST CIRCUIT AND WAVEFORM
6.0V or VCC x 2
VCC
Open
VIN
VOUT
PULSE
GENERATOR
tW
90%
RL
GND
VM
NEGATIVE
PULSE
10%
0V
tTHL (tF)
CL
VIN
VM
10%
D.U.T.
RT
90%
tTLH (tR)
tTLH (tR)
RL
90%
POSITIVE
PULSE
Test Circuit for 3-State Outputs
tTHL (tF)
VIN
90%
VM
VM
10%
10%
tW
0V
SWITCH POSITION
TEST
SWITCH
tPLZ/tPZL
6V or VCC x 2
tPLH/tPHL
Open
tPHZ/tPZH
GND
INPUT PULSE REQUIREMENTS
DEFINITIONS
FAMILY
Amplitude
RL = Load resistor; see AC CHARACTERISTICS for value.
CL = Load capacitance includes jig and probe capacitance:
See AC CHARACTERISTICS for value.
74ALVT16
Rep. Rate
3.0V or VCC
whichever v10MHz
is less
tW
500ns
tR
tF
v2.5ns v2.5ns
RT = Termination resistance should be equal to ZOUT of
pulse generators.
SW00025
1998 Feb 13
9
Philips Semiconductors
Product specification
20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
74ALVT16821
SSOP56: plastic shrink small outline package; 56 leads; body width 7.5 mm
1998 Feb 13
10
SOT371-1
Philips Semiconductors
Product specification
20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
74ALVT16821
TSSOP56: plastic thin shrink small outline package; 56 leads; body width 6.1mm
1998 Feb 13
11
SOT364-1
Philips Semiconductors
Product specification
20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
74ALVT16821
NOTES
1998 Feb 13
12
Philips Semiconductors
Product specification
20-bit bus-interface D-type flip-flop;
positive-edge trigger (3-State)
74ALVT16821
Data sheet status
Data sheet
status
Product
status
Definition [1]
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
 Copyright Philips Electronics North America Corporation 1998
All rights reserved. Printed in U.S.A.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
print code
Document order number:
yyyy mmm dd
13
Date of release: 05-96
9397-750-03574
Similar pages