ANADIGICS AWT6279RM20P9 Help3tm imt/wcdma 3.4 v/28.5 dbm hspa linear power amplifier module Datasheet

AWT6279
HELP3 IMT/WCDMA 3.4 V/28.5 dBm
HSPA Linear Power Amplifier Module
TM
Data Sheet - Rev 2.4
FEATURES
•
InGaP HBT Technology
•
High Efficiency:
42 % @ POUT = +28.5 dBm
AWT6279R
23 % @ POUT = +16 dBm
10 % @ POUT = +8 dBm
•
Low Quiescent Current: 8 mA
•
Low Leakage Current in Shutdown Mode: <1 µA
•
Internal Voltage Regulator Eliminates the
need for External Reference Voltage (No VREF
Required)
•
Optimized for a 50 Ω System
•
Low Profile Miniature Surface Mount Package
•
RoHS Compliant Package, 250 oC MSL-3
•
HSPA Compliant (no backoff)
M20 Package
10 Pin 4 mm x 4 mm x 1 mm
Surface Mount Module
APPLICATIONS
•
WCDMA/HSPA IMT-Band Wireless Handsets
and Data Devices
PRODUCT DESCRIPTION
The AWT6279 HELP3TM PA is the 3rd generation
WCDMA product for UMTS handsets. This PA
incorporates ANADIGICS’ HELP3TM technology to
provide low power consumption without the need for an
external voltage regulator. The device is manufactured
on an advanced InGaP HBT MMIC technology offering
state-of-the-art reliability, temperature stability, and
ruggedness. There are three selectable bias modes
that optimize efficiency for different output power
levels, and a shutdown mode with low leakage
current, increase handset talk and standby time. The
self-contained 4 mm x 4 mm x 1 mm surface mount
package incorporates matching networks optimized for
output power, efficiency, and linearity in a 50 Ω system.
GND at slug (pad)
VBATT 1
10 VCC
RFIN
2
9
GND
VMODE2 3
8
RFOUT
7
GND
6
GND
VMODE1 4
Bias Control
Voltage Regulation
VENABLE 5
Figure 1: Block Diagram
11/2008
AWT6279
GND
VBATT
1
10 VCC
RFIN
2
9
GND
VMODE2 3
8
RFOUT
VMODE1 4
7
GND
6
GND
VENABLE
5
GND
Figure 2: Pinout (X-ray Top View)
Table 1: Pin Description
2
PIN
NAME
DESCRIPTION
1
VBATT
Battery Voltage
2
RFIN
RF Input
3
VMODE2
Mode Control Voltage 2
4
VMODE1
Mode Control Voltage 1
5
VENABLE
PA Enable Voltage
6
GND
Ground
7
GND
Ground
8
RFOUT
RF Output
9
GND
Ground
10
VCC
Supply Voltage
Data Sheet - Rev 2.4
11/2008
AWT6279
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings
PARAMETER
MIN
MAX
UNIT
Supply Voltage (VCC)
0
+5
V
Battery Voltage (VBATT)
0
+6
V
Control Voltages (VMODE1, VMODE2, VENABLE)
0
+3.5
V
RF Input Power (PIN)
-
+10
dBm
-40
+150
°C
Storage Temperature (TSTG)
Stresses in excess of the absolute ratings may cause permanent damage.
Functional operation is not implied under these conditions. Exposure
to absolute ratings for extended periods of time may adversely affect
reliability.
Table 3: Operating Ranges
PARAMETER
MIN
TYP
MAX
UNIT
Operating Frequency (f)
1920
-
1980
MHz
Supply Voltage (VCC)
+3.2
+3.4
+4.2
V
POUT < +28.5 dBm
Enable Voltage (VENABLE)
+2.15
0
+2.4
-
+3.1
+0.5
V
PA "on"
PA "shut down"
Mode Control Voltage (VMODE1,VMODE2)
+2.15
0
+2.4
-
+3.1
+0.5
V
Low Bias Mode
High Bias Mode
28(1)
27(1)
15.5(1)
14.5(1)
28.5
27.5
16
15
28.5
27.5
16
15
dBm
-10
-
+90
°C
RF Output Power (POUT)
R99 WCDMA, HPM
HSPA (MPR=0), HPM
R99 WCDMA, LPM
HSPA (MPR=0), LPM
Case Temperature (TC)
COMMENTS
3GPP TS 34.121-1, Rel 7
Table C.11.1.3
The device may be operated safely over these conditions; however, parametric performance is guaranteed only
over the conditions defined in the electrical specifications.
Notes:
(1) For operation at Vcc = +3.2 V, Pout is derated by 0.5 dB.
Data Sheet - Rev 2.4
11/2008
3
AWT6279
Table 4: Electrical Specifications
(TC = +25 °C, VCC = +3.4 V, VBATT = +3.4 V, VENABLE = +2.4 V, 50 Ω system)
PARAMETER
MIN
TYP
MAX
UNIT
25
12
11
27
14
13
30
16
15
ACLR1 at 5 MHz offset (1)
-
-41
-44
-46
ACLR2 at 10 MHz offset
-
COMMENTS
POUT
VMODE1
VMODE2
dB
+28.5 dBm
+16 dBm
+8 dBm
0V
2.4 V
2.4 V
0V
0V
2.4 V
-38
-38
-38
dBc
+28.5 dBm
+16 dBm
+8 dBm
0V
2.4 V
2.4 V
0V
0V
2.4 V
-55
-55
-59
-48
-48
-48
dBc
+28.5 dBm
+16 dBm
+8 dBm
0V
2.4 V
2.4 V
0V
0V
2.4 V
38
19
8
42
23
10
-
%
+28.5 dBm
+16 dBm
+8 dBm
0V
2.4 V
2.4 V
0V
0V
2.4 V
Quiescent Current (Icq)
Low Bias Mode
Medium Bias Mode
-
8
14
11
21
mA
VMODE1 = +2.4 V, VMODE2 = +2.4 V
VMODE1 = +2.4 V, VMODE2 = 0 V
Mode Control Current
-
0.25
0.8
mA
through VMODE pins, VMODE = +2.4 V
Enable Current
-
0.2
0.8
mA
through VENABLE pin
BATT Current
-
3.5
5
mA
through VBATT pin, VMODE1 = +2.4 V,
VMODE2 = +2.4 V or 0 V
Leakage Current
-
<1
5
µA
VBATT = +4.2 V, VCC = +4.2 V,
VENABLE = 0 V, VMODE1 = 0 V, VMODE2
=0V
Noise in Receive Band
-
-137
-135
Harmonics
2fo
3fo, 4fo
-
-44
-50
-35
-35
dBc
Input Impedance
-
-
2:1
VSWR
Gain
Power-Added Efficiency (1)
Spurious Output Level
(all spurious outputs)
Load mismatch stress with no
permanent degradation or failure
dBm/Hz 2110 MHz to 2170 MHz
-
-
-70
dBc
POUT < +28.5 dBm
In-band load VSWR < 5:1
Out-of-band load VSWR < 10:1
Applies over all operating
conditions
8:1
-
-
VSWR
Applies over full operating range
Notes:
(1) ACLR and Efficiency measured at 1950 MHz.
4
POUT < +28.5 dBm
Data Sheet - Rev 2.4
11/2008
AWT6279
APPLICATION INFORMATION
To ensure proper performance, refer to all related
Application Notes on the ANADIGICS web site:
http://www.anadigics.com
logic level (see Operating Ranges table) to the VMODE
voltages. The Bias Control table lists the recommended
modes of operation for various applications.
Shutdown Mode
The power amplifier may be placed in a shutdown
mode by applying logic low levels (see Operating
Ranges table) to the VENABLE, VMODE1 and VMODE2
voltages.
Three operating modes are recommended to optimize
current consumption. High Bias/High Power operating
mode is for POUT levels > 16 dBm. At ~16dBm - 7
dBm, the PA should be “Mode Switched” to Medium
Power Mode. For POUT levels < ~8 dBm, the PA can be
switched to Low Power Mode for even lower quiescent
current consumption.
Bias Modes
The power amplifier may be placed in either a Low Bias
mode or a High Bias mode by applying the appropriate
Table 5: Bias Control
APPLICATION
POUT
LEVELS
BIAS
MODE
VENABLE
VMODE1
VMODE2
VCC
VBATT
WCDMA - low power
(Low Bias Mode)
< +8 dBm
Low
+2.4 V
+2.4 V
+2.4 V
3.2 - 4.2 V
> 3.2 V
WCDMA - med power
(Medium Bias Mode)
7 POUT <
+16 dBm
Low
+2.4 V
+2.4 V
0V
3.2 - 4.2 V
> 3.2 V
WCDMA - high power
(High Bias Mode)
> +16 dBm
High
+2.4 V
0V
0V
3.2 - 4.2 V
> 3.2 V
Optional lower VCC in
low power mode
< +7 dBm
Low
+2.4 V
+2.4 V
2.4 V
1.5 V
> 3.2 V
-
Shutdown
0V
0V
0V
3.2 - 4.2 V
> 3.2 V
Shutdown
VBATT
VCC
C5
2.2 µF
C1
0.01µF
1
2
RF IN
3
VMODE2
VMODE1
VENABLE
C2
0.01µF
VBATT
VCC
RFIN
GND
10
C3
0.01µF
C4
2.2µF ceramic
9
VMODE2
RFOUT
8
4
VMODE1
GND
7
5
VENABLE
GND
6
RF OUT
GND
at slug
10K 
Optional
pull-down
Figure 3: Application Circuit Schematic
Data Sheet - Rev 2.4
11/2008
5
AWT6279
PACKAGE OUTLINE
Figure 4: M20 Package Outline - 10 Pin 4 mm x 4 mm x 1 mm Surface Mount Module
79R
79R
Figure 5: Branding Specification - M20 Package
6
Data Sheet - Rev 2.4
11/2008
AWT6279
COMPONENT PACKAGING
Figure 6: Tape & Reel Packaging
Table 6: Tape & Reel Dimensions
PACKAGE TYPE
TAPE WIDTH
POCKET PITCH
REEL CAPACITY
MAX REEL DIA
4 mm x 4 mm x 1mm
12 mm
8 mm
2500
13"
Data Sheet - Rev 2.4
11/2008
7
AWT6279
ORDERING INFORMATION
ORDER NUMBER
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
AWT6279RM20P8
-10 oC to +90 oC
RoHS Compliant 10 Pin
4 mm x 4 mm x 1 mm Tape and Reel, 2500 pieces per Reel
Surface Mount Module
AWT6279RM20P9
-10 oC to +90 oC
RoHS Compliant 10 Pin
4 mm x 4 mm x 1 mm Partial Tape and Reel
Surface Mount Module
COMPONENT PACKAGING
ANADIGICS, Inc.
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
E-mail: [email protected]
IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice.
The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to
change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed
to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers
to verify that the information they are using is current before placing orders.
warning
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product
in any such application without written consent is prohibited.
8
Data Sheet - Rev 2.4
11/2008
Similar pages