ANADIGICS AWU6615RM47P9 Help3e dual-band cell & pcs wcdma 3.4 v linear power amplifier module Datasheet

AWU6615
HELP3ETM Dual-band Cell & PCS WCDMA
3.4 V Linear Power Amplifier Module
Data Sheet - Rev 2.6
FEATURES
•
InGaP HBT Technology
•
High Efficiency:
• 39 % @ POUT = +28.7 dBm
• 22 % @ POUT = +16.6 dBm
• 9 % @ POUT = +8 dBm
Low Quiescent Current: 4.5 mA
•
Internal Voltage Regulation
•
Built-in Directional Coupler
•
Common VMODE Control Line
AW
U
661
Simplified VCC Bus PCB routing
Reduced External Component Count
•
Low Profile Surface Mount Package: 1 mm
•
RoHS Compliant Package, 260 oC MSL-3
APPLICATIONS
Cell & PCS Dual-band Wireless Handsets and
Data Devices for HSDPA/HSPA networks.
PRODUCT DESCRIPTION
switches. This PA has built-in directional couplers
for each band, with a common coupler output port
CPL_OUT. These couplers provide high directivity and
23 dB Coupling. The 3 mm x 5 mm x 1 mm surface
mount package incorporates matching networks
optimized for output power, efficiency and linearity in
a 50 Ω system.
O
•
M47 Package
14 Pin 3 mm x 5 mm x 1 mm
Surface Mount Module
LE
•
•
5
TE
•
O
BS
AWU6615 addresses the demand for increased
integration in dual-band handsets for WCDMA
networks. The small footprint 3 mm x 5 mm x 1
mm surface- mount RoHS compliant package
contains independent RF PA paths to ensure optimal
performance in both frequency bands, while achieving
a 25% PCB space savings compared with solutions
requiring two single-band PAs. The package pinout
was chosen to enable handset manufacturers to easily
route bias to both power amplifiers and simplify control
with common mode pins. The device is manufactured
on an advanced InGaP HBT MMIC technology offering
state-of-the-art reliability, temperature stability, and
ruggedness. The AWU6615 is part of ANADIGICS’
High-Efficiency-at-Low-Power (HELP™) family of
WCDMA power amplifiers, which deliver low quiescent
currents and significantly greater efficiency without
the need of an external DC-DC converter. Through
selectable bias modes, the AWU6615 achieves
optimal efficiency, specifically at low- and mid-range
power levels where the PA typically operates, thereby
dramatically increasing handset talk-time. Its built-in
voltage regulator eliminates the need for external
02/2012
VEN_CELL
1
14 GND
Bias Control
Voltage Regulation
RFIN_CELL
CPL
2
VMODE1 3
12 VCC
VBATT 4
11 VCCA
VMODE2 5
10 CPLOUT
RFIN_PCS 6
VEN_PCS 7
13 RFOUT_CELL
CPL
Bias Control
Voltage Regulation
9 GND
8
GND at Slug (pad)
Figure 1: Block Diagram
RFOUT_PCS
AWU6615
VMODE1
CPLOUT
LE
TE
VMODE2
Figure 2: Pinout
PIN
NAME
DESCRIPTION
VEN_CELL
Enable Voltage for Cell Band
BS
1
O
Table 1: Pin Description
3
VMODE1
Mode Control Voltage for Cell
and PCS Bands
4
VBATT
Battery Voltage
5
VMODE2
Mode Control Voltage for Cell
6
RFIN_PCS
RF Input for PCS Band
7
VEN_PCS
Enable Voltage for PCS Band
8
RFOUT_PCS
9
GND
10
CPLOUT
11
VCCA
12
VCC
O
RFIN_CELL
13
14
2
RF Input for Cell Band
2
RF Output for PCS Band
Ground
Coupler Output Port
Battery Voltage A
Supply Voltage
RFOUT_CELL RF Output for Cell Band
GND
Ground
Data Sheet - Rev 2.6
02/2012
AWU6615
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings
PARAMETER
MIN
MAX
UNIT
Supply Voltage (VBATT, VCC, VCCA)
0
+5
V
Mode Control Voltage (VMODE1, VMODE2)
0
+3.5
V
Enable Voltage (VEN_CELL, VEN_PCS)
0
+3.5
V
RF Input Power (PIN)
-
+10
dBm
-40
+150
C
Storage Temperature (TSTG)
TE
Stresses in excess of the absolute ratings may cause permanent damage.
Functional operation is not implied under these conditions. Exposure
to absolute ratings for extended periods of time may adversely affect
reliability.
Table 3: Operating Ranges
MAX
UNIT
-
849
1910
MHz
+3.2
+3.4
+4.2
V
+1.35
0
+1.8
-
+3.1
+0.5
V
PA "on"
PA "shut down"
+1.35
0
+1.8
-
+3.1
+0.5
V
Low Bias Mode
High Bias Mode
RF Output Power, Band 5, UMTS
R99 WCDMA, HPM
HSPA (MPR = 0 dB), HPM
R99 WCDMA, MPM
HSPA (MPR = 0 dB), MPM
R99 WCDMA, LPM
HSPA (MPR = 0 dB), LPM
28.2(1)
27.2(1)
16.1(1)
15.1(1)
7.5(1)
6.5(1)
28.7
27.7
16.6
15.6
8.0
7.0
-
RF Output Power, Band 2, UMTS
R99 WCDMA, HPM
HSPA (MPR = 0 dB), HPM
R99 WCDMA, MPM
HSPA (MPR = 0 dB), MPM
R99 WCDMA, LPM
HSPA (MPR = 0 dB), LPM
28.3(1)
27.3(1)
16.5(1)
15.5(1)
8.0(1)
7.0(1)
28.8
27.8
17.0
16.0
8.5
7.5
-
-30
-
+90
Operating Frequency (f)
TYP
824
1850
O
Supply Voltage (VCC and VBATT)
Enable Voltage (VEN)
MIN
LE
PARAMETER
O
BS
Mode Control Voltage (VMODE0, VMODE1)
Case Temperature (TC)
COMMENTS
Cellular (Band 5)
PCS (Band 2)
dBm
3GPP TS
34.121-1, REL8
Table C.11.1.3, Subtest 1
dBm
3GPP TS
34.121-1, REL8
Table C.11.1.3, Subtest 1
°C
The device may be operated safely over these conditions; however, parametric performance is guaranteed only
over the conditions defined in the electrical specifications.
Notes:
(1) For operation at VCC = +3.2 V, TC = +90 8C POUT is derated by 0.5 dB.
3
Data Sheet - Rev 2.6
02/2012
AWU6615
Table 4: Electrical Specifications - Cellular Band (Band 5)
(TC = +25 °C, VBATT = VCC = +3.4 V, VEN_CELL = +1.8 V, 50 Ω system, R99 uplink waveform)
COMMENTS
PARAMETER
MIN
TYP
MAX
UNIT
Gain
25.5
14.5
9
27.5
17
11.5
30
20
14
dB
+28.7 dBm 0 V
+16.6 dBm 1.8 V
+8 dBm
1.8 V
0V
0V
1.8 V
ACLR1 @ 5 MHz Offset (1)
-
-42
-42
-41
-37
-37
-37
dBc
+28.7 dBm 0 V
+16.6 dBm 1.8 V
+8 dBm
1.8 V
0V
0V
1.8 V
ACLR2 @ 10 MHz Offset (1)
-
-58
-55
-54
-48
-48
-48
dBc
+28.7 dBm 0 V
+16.6 dBm 1.8 V
+8 dBm
1.8 V
0V
0V
1.8 V
Power-Added Efficiency (1)
35
18
6
39
22
9
-
%
+28.7 dBm 0 V
+16.6 dBm 1.8 V
+8 dBm
1.8 V
0V
0V
1.8 V
VMODE1
TE
POUT
VMODE2
6
mA
through VCC pin,
VMODE1 = +1.8 V, VMODE2 =+1.8 V
0.1
0.15
mA
through VMODE pins, VMODE1= +1.8 V
1.5
2.5
mA
through VBATT pin, VMODE1 = +1.8 V,
VMODE2 = +1.8 V
-
0.15
0.25
mA
through VEN_CELL pin, VMODE = 1.8 V
-
-133
-
dBm/Hz
-
-40
-50
-30
-38
dBc
Input Impedance
-
-
2:1
VSWR
Coupling Factor
-
23
-
dB
Mode Control Current
-
Battery Current
-
Enable Current
O
Harmonics
2fo
3fo, 4fo
BS
Noise in Receive Band
O
-
LE
4
Quiescent Current (Icq)
Spurious Output Level
(all spurious outputs)
Load mismatch stress with no
permanent degradation or failure
-
-
-65
dBc
8:1
-
-
VSWR
Notes:
(1) Efficiency and ACLR measured at 836.5 MHz.
4
Data Sheet - Rev 2.6
02/2012
869 MHz to 894 MHz
POUT < +28.7 dBm
POUT < +28.7 dBm
In-band Load VSWR < 5:1
Out-of-band Load VSWR < 10:1
Applies over all operating
conditions
Applies over full operating
conditions
AWU6615
Table 5: Electrical Specifications - PCS Band (Band 2)
(TC = +25 °C, VBATT = VCC = +3.4 V, VEN_PCS = +1.8 V, 50 Ω system, R99 uplink waveform)
TYP
MAX
UNIT
25
12
8
27
15
11
30.5
18
13.5
dB
+28.8 dBm
+17 dBm
+8.5 dBm
0V
1.8 V
1.8 V
0V
0V
1.8 V
ACLR1 @ 5 MHz Offset
-
-41
-40
-42
-37
-37
-37
dBc
+28.8 dBm
+17 dBm
+8.5 dBm
0V
1.8 V
1.8 V
0V
0V
1.8 V
ACLR2 @ 5 MHz Offset
-
-52
-53
-56
-48
-48
-48
dBc
+28.8 dBm
+17 dBm
+8.5 dBm
0V
1.8 V
1.8 V
0V
0V
1.8 V
35
18
6
39
21
8.5
-
+28.8 dBm
+17 dBm
+8.5 dBm
0V
1.8 V
1.8 V
0V
0V
1.8 V
Quiescent Current (Icq)
-
5
7
Mode Control Current
-
Battery Current
-
VMODE1
TE
Power-Added Efficiency (1)
POUT
%
mA
VMODE2
through VCC Pin,
VMODE1 = +1.8 V, VMODE2 =+1.8 V
LE
Gain
0.1
0.15
mA
through VMODE pins, VMODE1= +1.8 V
1.5
2.5
mA
through VBATT pin, VMODE1 = +1.8 V,
VMODE2 = +1.8 V
0.15
0.25
mA
through VEN_CELL pin,
VMODE1 = VMODE2 = 1.8 V
-
<1
5
A
VBATT = +4.2 V, VCC = +4.2 V,
VEN_CELL = 0 V, VMODE1 = 0 V,
VMODE2 = 0 V
Total Decoder Current on VBATT
(Shutdown Mode)
-
12
22
A
VBATT = +4.2 V, VCC = +4.2 V,
VEN = 0 V, VMODE1 = VMODE2 = 0 V
Noise in Receive Band
-
-134
-
Harmonics
2fo
3fo, 4fo
-
-42
-50
-30
-38
dBc
Input Impedance
-
-
2:1
VSWR
Coupling Factor
-
22.5
-
dB
O
BS
HBT Leakage Current (VCC)
O
-
Enable Current
Spurious Output Level
(all spurious outputs)
Load mismatch stress with no
permanent degradation or failure
dBm/Hz 1930 MHz to 1990 MHz
POUT < +28.8 dBm
-
-
-65
dBc
POUT < +28.8 dBm
In-band Load VSWR < 5:1
Out-of-band Load VSWR < 10:1
Applies over all operating conditions
8:1
-
-
VSWR
Applies over full operating conditions
Notes:
1.Efficiency and ACLR measured at 1880 MHz.
5
COMMENTS
MIN
PARAMETER
Data Sheet - Rev 2.6
02/2012
AWU6615
APPLICATION INFORMATION
To ensure proper performance, refer to all related
Application Notes on the ANADIGICS web site:
http://www.anadigics.com
Shutdown Mode
The power amplifier may be placed in a shutdown
mode by applying logic low levels (see Operating
Ranges table) to the VENABLE voltage.
Bias Modes, Medium Bias Mode
The power amplifier may be placed in Low Bias mode
or a High Bias mode by applying the appropriate
logic level (see Operating Ranges table) to the
VMODE1, and VMODE2 pins. The Bias Control table lists
the recommended modes of operation for various
applications.
Vcontrols
Venable/Vmode(s)
TE
On Sequence Start
T_0N = 0µ
Rise/Fall Max 1µS
Defined at 10% to 90%
of Min/Max Voltage
Off Sequence Start
T_0FF = 0µ
OFF Sequence
LE
ON Sequence
RFIN_CELL,PCS
notes 1,2
O
VEN_CELL,PCS
VCC, VCCA
BS
note 1
T_0N+1µS
T_0N+3µS
T_0FF+2µS T_0FF+3µS
Referenced After 90% of Rise
Time
Referenced Before10% of Fall
Time
Figure 3: Minimum Recommended ON/OFF Timing Sequence
O
Notes:
(1) Level might be changed after RF is ON.
(2) RF OFF defined as PIN ≤ -30 dBm.
(3) Switching simultaneously between VMODE and VEN is not recommended.
Table 6: Bias Control
APPLICATION
POUT
LEVELS
BIAS
MODE
VEN
VMODE1
VMODE2
VCC
VBATT
WCDMA - low power
(Low Bias Mode)
< +8 dBm
Low
+1.8 V
+1.8
+1.8 V
3.2 - 4.2 V
> 3.2 V
WCDMA - med power
(Medium Bias Mode)
> +8 dBm
< +16.5 dBm
Low
+1.8 V
+1.8 V
0V
3.2 - 4.2 V
> 3.2 V
WCDMA - high power
(High Bias Mode)
> +16.5 dBm
High
+1.8 V
0V
0V
3.2 - 4.2 V
> 3.2 V
-
Shutdown
0V
-
-
3.2 - 4.2 V
> 3.2 V
Shutdown
6
Data Sheet - Rev 2.6
02/2012
AWU6615
VEN_CELL
1
14
Bias Control
Voltage Regulation
RFIN_CELL
CPL
2
13
68 pF
12
3
VMODE1
RFOUT_CELL
VCC
1000 pF
2.2 F
68pF
4
11
1000 pF
5
VMODE2
RFIN_PCS
10
CPL
6
Bias Control
Voltage Regulation
GND at Slug (pad)
O
BS
O
Figure 4: Application Circuit
7
Data Sheet - Rev 2.6
02/2012
2.2 F
CPLOUT
9
8
LE
7
VEN_PCS
TE
VBATT
33 pF
RFOUT_PCS
AWU6615
BS
O
LE
TE
PACKAGE OUTLINE
O
Figure 5: Package Outline - 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module
Pin 1 Identifier
Date Code
YY= Year WW= Work Week
6615R
LLLLNN
CC
YYWW
Figure 6: Branding Specification
8
Data Sheet - Rev 2.6
02/2012
Part Number
Lot Number
Country Code
AWU6615
ORDERING INFORMATION
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
COMPONENT PACKAGING
AWU6615RM47Q7
-30 °C to +90 °C
RoHS Compliant 14 Pin
3 mm x 5 mm x 1 mm
Surface Mount Module
Tape and Reel, 2500 pieces per Reel
AWU6615RM47P9
-30 °C to +90 °C
RoHS Compliant 14 Pin
3 mm x 5 mm x 1 mm
Surface Mount Module
Partial Tape and Reel
ANADIGICS
BS
O
LE
TE
ORDER NUMBER
O
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice.
The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to
change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed
to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers
to verify that the information they are using is current before placing orders.
warning
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product
in any such application without written consent is prohibited.
9
Data Sheet - Rev 2.6
02/2012
Similar pages