ETC2 AZ10EL16VO Ecl/pecl oscillator gain stage and buffer with enable Datasheet

ARIZONA MICROTEK, INC.
AZ10EL16VO
AZ100EL16VO
ECL/PECL Oscillator Gain Stage and Buffer with Enable
FEATURES
•
•
•
•
•
•
•
Green and RoHS Compliant Available
250ps Propagation Delay on Q̄ Output
High Voltage Gain vs. Standard EL16
For Oscillator Applications
Available in 2x2 or 3x3mm MLP Package
75kΩ Enable Pull-Down Resistor
S–Parameter (.s2p) and IBIS Model
Files Available on Arizona Microtek Website
DESCRIPTION
The AZ10/100EL16VO is an oscillator gain stage with a high gain output buffer including an enable. The
QHG/Q̄HG outputs have a voltage gain several times greater than the Q/Q̄ outputs. An enable input (EN
¯¯ ) allows
continuous oscillator operation. When EN
¯¯ is LOW or floating (NC), input data is passed to both sets of outputs.
When EN
¯¯ is HIGH, the QHG/Q̄HG outputs will be forced LOW/HIGH respectively, while input data will continue to
be passed to the Q/Q̄ outputs. The EN
¯¯ input can be driven with an ECL/PECL signal or a CMOS logic signal.
The input impedance of the D/D̄ inputs remain constant for all operating modes since forcing the outputs via the
EN
¯¯ pin does not power-down the chip but only disables the high gain QHG/Q̄HG outputs.
Input protection diodes are included on the D/D̄ inputs for enhanced ESD protection.
The EL16VO also provides a VBB output that supports 1.5mA sink/source current. When used, the VBB pin
should be bypassed to ground or VCC via a 0.01μF capacitor.
Any used output must have an external pull down resistor. For 3.3V operation, an 180Ω resistor to VEE is
recommended if an AC coupled load is present. At 5.0V, a 330Ω resistor is recommended for the AC load case.
Alternately, a 50Ω load terminated to VCC – 2V or the Thevenin equivalent may be driven directly. Unused outputs
may be left floating (NC).
NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established.
PIN/PAD DESCRIPTION
Q
Q
D
QHG
D
QHG
EN
PIN
D/D̄
Q/Q̄
QHG/Q̄HG
VBB
EN
¯¯
VCC
VEE
FUNCTION
Data Inputs
Data Outputs
Data Outputs w/High Gain
Reference Voltage Output
Enable Input
Positive Supply
Negative Supply
VBB
1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541
www.azmicrotek.com
AZ10EL16VO
AZ100EL16VO
PACKAGE AVAILABILITY
PACKAGE
PART NUMBER
MLP 8 (2x2) Green / RoHS
Compliant / Lead (Pb) Free
AZ100EL16VONG
MLP 8 (2x2)
AZ100EL16VONB
MLP 8 (2x2) RoHS Compliant /
Lead (Pb) Free
MLP 8 (2x2x0.75) Green / RoHS
Compliant / Lead (Pb) Free
AZ100EL16VONB+
AZ100EL16VONBG
MLP 16 (3x3)
AZ10/100EL16VOL
MLP 16 (3x3) Green / RoHS
Compliant / Lead (Pb) Free
AZ10/100EL16VOLG
SOIC 8
AZ10EL16VOD
SOIC 8
AZ100EL16VOD
TSSOP 8
AZ10EL16VOT
TSSOP 8 RoHS Compliant / Lead
(Pb) Free
AZ10EL16VOT+
TSSOP 8
AZ100EL16VOT
TSSOP 8 RoHS Compliant / Lead
(Pb) Free
TSSOP 10 RoHS Compliant / Lead
(Pb) Free
TSSOP 10 RoHS Compliant / Lead
(Pb) Free
DIE
DIE
1
2
3
4
5
6
June 2007 * REV - 23
AZ100EL16VOT+
AZ10EL16VOU+
AZ100EL16VOU+
AZ10/100EL16VOXP
AZ10/100EL16VOXR
MARKING
P0G
<Date Code>
P4
<Date Code>
P4+
<Date Code>
P4G
<Date Code>
AZM
16J
<Date Code>
AZMG
16J
<Date Code>
AZM10
EL16VO
AZM100
EL16VO
AZT
16VO
AZT+
16VO
AZH
16VO
AZH+
16VO
AZT+
16VOU
AZH+
16VOU
N/A
N/A
NOTES
1,2
1,2,3
1,2
1,2
1,2
1,2
1,2,4
1,2,4
1,2,4
1,2,4
1,2,4
1,2,4
1,2,4
1,2,4
5
6
Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts) Tape & Reel.
Date code format: “Y” or “YY” for year followed by “WW” for week.
Parts marked JNB for date codes prior to 4WW (prior to 2004).
Date code “YWW” or “YYWW” on underside of part.
Waffle Pack. Die thickness 180 μm.
Die on 7 inch Tape & Reel, 3k parts per reel. Die thickness 180 μm.
www.azmicrotek.com
2
AZ10EL16VO
AZ100EL16VO
TIMING DIAGRAM
D
TRUTH TABLE
EN
¯¯
Q/Q̄
LOW or NC
Data
HIGH
Data
NC = No Connect
QHG
Data
LOW
Q̄HG
Data
HIGH
EN
Q
QHG
Absolute Maximum Ratings are those values beyond which device life may be impaired.
Symbol
VCC
VI
VEE
VI
VI_DIFF
1.
Characteristic
PECL Power Supply
(VEE = 0V)
PECL Input Voltage
(VEE = 0V)
ECL Power Supply
(VCC = 0V)
ECL Input Voltage
(VCC = 0V)
Differential Input Voltage
D/D̄
Output Current
— Continuous
IOUT
— Surge
TA
Operating Temperature Range
TSTG
Storage Temperature Range
VI_DIFF is the voltage difference between D and D̄
June 2007 * REV - 23
www.azmicrotek.com
3
Rating
0 to +6.0
0 to +6.0
-6.0 to 0
-6.0 to 0
0 to ±1.6
50
100
-40 to +85
-65 to +150
Unit
Vdc
Vdc
Vdc
Vdc
Vpp1
mA
°C
°C
AZ10EL16VO
AZ100EL16VO
10K ECL DC Characteristics (VEE = -3.0V to -5.5V, VCC = GND)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
Characteristic
1
Min
-1080
-1950
-40°C
Typ
Max
-890
-1650
Output HIGH Voltage
Output LOW Voltage1
Input HIGH Voltage
D/D̄ -1230
-430
EN
¯¯
-1230
VCC
Input LOW Voltage
-1500
D/D̄ -2300
-1500
EN
¯¯
VEE
Reference Voltage
-1430
-1300
Input HIGH Current
D/D̄
60
EN
¯¯
150
Input LOW Current
0.5
Power Supply Current
40
Each output is terminated through a 50Ω resistor to VCC – 2V.
Min
-1020
-1950
0°C
Typ
Max
-840
-1630
Min
-980
-1950
-1170
-1170
-380
VCC
-2260
VEE
-1380
-1480
-1480
-1260
25°C
Typ
-1130
-1130
-360
VCC
-1060
-1060
-310
VCC
mV
-2240
VEE
-1360
-1480
-1480
-1240
-2190
VEE
-1310
-1445
-1445
-1190
mV
60
150
μA
60
150
0.5
Max
-720
-1595
Unit
Min
-910
-1950
60
150
0.5
85°C
Typ
Max
-810
-1630
0.5
40
40
40
mV
mV
mV
μA
mA
10K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
2.
3.
Characteristic
1,2
Min
2220
1350
-40°C
Typ
Max
2410
1650
Min
2280
1350
0°C
Typ
Max
2460
1670
Min
2320
1350
Output HIGH Voltage
Output LOW Voltage1,2
Input HIGH Voltage
2870
2130
2920
2170
D/D̄1
2070
VCC
21301
VCC
21701
EN
¯¯
20701
Input LOW Voltage
1800
1040
1820
1060
D/D̄1
1000
18001
VEE
18201
VEE
EN
¯¯
VEE
Reference Voltage1
1870
2000
1920
2040
1940
Input HIGH Current
D/D̄
60
60
EN
¯¯
150
150
Input LOW Current
D/D̄
0.5
0.5
0.5
EN
¯¯ 3
-300
-300
-300
Power Supply Current
40
40
For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value.
Each output is terminated through a 50Ω resistor to VCC – 2V.
Specified with EN
¯¯ forced to VEE.
June 2007 * REV - 23
www.azmicrotek.com
4
25°C
Typ
85°C
Typ
Min
2390
1350
2940
VCC
2240
22401
2990
VCC
mV
1820
18201
2060
1110
VEE
1990
1855
18551
2110
mV
60
150
μA
60
150
Max
2580
1705
Unit
Max
2490
1670
mV
μA
0.5
-300
40
mV
mV
40
mA
AZ10EL16VO
AZ100EL16VO
10K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
2.
3.
Characteristic
1,2
Min
3920
3050
-40°C
Typ
Max
4110
3350
Min
3980
3050
0°C
Typ
Max
4160
3370
Min
4020
3050
25°C
Typ
Output HIGH Voltage
Output LOW Voltage1,2
Input HIGH Voltage
4570
3830
4620
3870
D/D̄1
3770
VCC
38301
VCC
38701
EN
¯¯
37701
Input LOW Voltage
3500
2740
3520
2760
D/D̄1
2700
35001
VEE
35201
VEE
EN
¯¯
VEE
Reference Voltage1
3570
3700
3620
3740
3640
Input HIGH Current
D/D̄
60
60
EN
¯¯
150
150
Input LOW Current
0.5
0.5
0.5
D/D̄
-1400
-1400
EN
¯¯ 3 -1400
Power Supply Current
40
40
For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.
Each output is terminated through a 50Ω resistor to VCC – 2V.
Specified with EN
¯¯ forced to VEE.
85°C
Typ
Min
4090
3050
4640
VCC
3940
39401
4690
VCC
mV
3520
35201
3760
2810
VEE
3690
3555
35551
3810
mV
60
150
μA
60
150
Max
4280
3405
Unit
Max
4190
3370
mV
mV
mV
μA
0.5
-1400
40
40
mA
100K ECL DC Characteristics (VEE = -3.0V to -5.5V, VCC = GND)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
Characteristic
1
Min
-1085
-1900
-40°C
Typ
Max
-880
-1555
Output HIGH Voltage
Output LOW Voltage1
Input HIGH Voltage
D/D̄ -1165
-390
EN
¯¯
-1165
VCC
Input LOW Voltage
-1475
D/D̄ -2250
-1475
EN
¯¯
VEE
Reference Voltage
-1390
-1250
Input HIGH Current
D/D̄
60
EN
¯¯
150
Input LOW Current
0.5
Power Supply Current
40
Each output is terminated through a 50Ω resistor to VCC – 2V.
June 2007 * REV - 23
Min
-1025
-1900
0°C
Typ
Max
-880
-1620
Min
-1025
-1900
-1165
-1165
-390
VCC
-2250
VEE
-1390
-1475
-1475
-1250
-1165
-1165
-390
VCC
-1165
-1165
-390
VCC
mV
-2250
VEE
-1390
-1475
-1475
-1250
-2250
VEE
-1390
-1475
-1475
-1250
mV
60
150
μA
www.azmicrotek.com
5
60
150
Max
-880
-1620
Unit
Min
-1025
-1900
0.5
40
85°C
Typ
Max
-880
-1620
60
150
0.5
25°C
Typ
0.5
40
46
mV
mV
mV
μA
mA
AZ10EL16VO
AZ100EL16VO
100K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
2.
3.
Characteristic
1,2
Min
2215
1400
-40°C
Typ
Max
2420
1745
Min
2275
1400
0°C
Typ
Max
2420
1680
Min
2275
1400
25°C
Typ
Output HIGH Voltage
Output LOW Voltage1,2
Input HIGH Voltage
2910
2135
2910
2135
D/D̄1
2135
VCC
21351
VCC
21351
EN
¯¯
21351
Input LOW Voltage
1825
1050
1825
1050
D/D̄1
1050
18251
VEE
18251
VEE
EN
¯¯
VEE
Reference Voltage1
1910
2050
1910
2050
1910
Input HIGH Current
D/D̄
60
60
EN
¯¯
150
150
Input LOW Current
0.5
0.5
0.5
D/D̄
-300
-300
-300
EN
¯¯ 3
Power Supply Current
40
40
For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value.
Each output is terminated through a 50Ω resistor to VCC – 2V.
Specified with EN
¯¯ forced to VEE.
85°C
Typ
Min
2275
1400
2910
VCC
2135
21351
2910
VCC
mV
1825
18251
2050
1050
VEE
1910
1825
18251
2050
mV
60
150
μA
60
150
Max
2420
1680
Unit
Max
2420
1680
mV
mV
mV
μA
0.5
-300
40
46
mA
100K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
2.
3.
Characteristic
1,2
Min
3915
3100
-40°C
Typ
Max
4120
3445
Min
3975
3100
0°C
Typ
Max
4120
3380
Min
3975
3100
Output HIGH Voltage
Output LOW Voltage1,2
Input HIGH Voltage
4610
3835
4610
3835
D/D̄1
3835
VCC
38351
VCC
38351
EN
¯¯
38351
Input LOW Voltage
3525
2750
3525
2750
D/D̄1
2750
35251
VEE
35251
VEE
EN
¯¯
VEE
Reference Voltage1
3610
3750
3610
3750
3610
Input HIGH Current
D/D̄
60
60
EN
¯¯
150
150
Input LOW Current
0.5
0.5
0.5
D/D̄
-1400
-1400
EN
¯¯ 3 -1400
Power Supply Current
40
40
For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.
Each output is terminated through a 50Ω resistor to VCC – 2V.
Specified with EN
¯¯ forced to VEE.
June 2007 * REV - 23
www.azmicrotek.com
6
25°C
Typ
85°C
Typ
Min
3975
3100
4610
VCC
3835
38351
4610
VCC
mV
3525
35251
3750
2750
VEE
3610
3525
35251
3750
mV
60
150
μA
60
150
Max
4120
3380
Unit
Max
4120
3380
mV
μA
0.5
-1400
40
mV
mV
46
mA
AZ10EL16VO
AZ100EL16VO
AC Characteristics (VEE = -3.0V to -5.5V; VCC = GND or VEE = GND, VCC = +3.0V to +5.5V)
Symbol
Characteristic
-40°C
Typ
Min
Max
Min
0°C
Typ
Max
Min
25°C
Typ
Max
Min
85°C
Typ
Max
Propagation Delay
100
300
100
300
100
200
300
100
300
D to Q/Q̄ Outputs
(SE)
150
450
150
450
150
290
450
150
450
D to QHG/Q̄HG Outputs (SE)
tSKEW
Duty Cycle Skew1
(SE)
5
20
5
20
5
20
5
20
VPP (AC) Input Swing2
80
1000
80
1000
80
1000
80
1000
Output Rise/Fall Times
tr/tf
80
240
80
240
80
135
240
80
240
(20% – 80%)
1.
Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device.
2.
VPP is the peak-to-peak differential input swing for which AC parameters are guaranteed. The device has a voltage gain of ≈20 to Q/Q̄ outputs
and a voltage gain of ≈100 to QHG/Q̄HG outputs.
tPLH/tPHL
AC PP INPUT
D
D
V PP (AC)
Typical Large Signal Outputs, QHG/Q̄HG
1000
900
VOUTpp (mV)
800
700
600
500
400
300
200
100
0
0
500
1000
1500
2000
2500
3000
3500
4000
FREQUENCY (MHz)
Measured with 750mv differential input, VEEP NC, QHG/Q̄HG each terminated to VCC-2V via 50 Ω
resistors.
Q HG
Q HG
V OUTpp
June 2007 * REV - 23
www.azmicrotek.com
7
Unit
ps
ps
mV
ps
AZ10EL16VO
AZ100EL16VO
2.05
0.00
-5.00
-10.00
1.9
-15.00
1.85
-20.00
1.8
Phase
1.95
S11 MAG
S11 PH
Phase
Magnitude
2
S12 MAG
S12 PH
-25.00
50
150
250
350
450
550
650
750
850
950
1050 1150 1250 1350
FREQUENCY (MHz)
S11, D to Q̄, 50 Ω load to VCC – 2V
250
200
180
160
200
Magnitude
140
120
150
100
80
100
60
40
50
20
0
0
50
150
250
350
450
550
650
750
850
950
1050 1150 1250 1350
FREQUENCY (MHz)
S12, D to Q̄, 50 Ω load to VCC – 2V
June 2007 * REV - 23
www.azmicrotek.com
8
AZ10EL16VO
AZ100EL16VO
200.00
40
180.00
35
160.00
30
140.00
120.00
100.00
20
Phase
Magnitude
25
S21 MAG
S21 PH
80.00
15
60.00
10
40.00
5
20.00
0
0.00
50
150
250
350
450
550
650
750
850
950
1050 1150 1250 1350
FREQUENCY (MHz)
S21, D to Q̄, 50 Ω load to VCC – 2V
0.6
45.00
40.00
0.5
35.00
30.00
25.00
0.3
20.00
0.2
15.00
10.00
0.1
5.00
0
0.00
50
150
250
350
450
550
650
750
850
950
1050 1150 1250 1350
FREQUENCY (MHz)
S22, D to Q̄, 50 Ω load to VCC – 2V
June 2007 * REV - 23
www.azmicrotek.com
9
Phase
Magnitude
0.4
S22 MAG
S22 PH
AZ10EL16VO
AZ100EL16VO
Application Circuit for CMOS Inputs
R11
Input
Type
AC
Coupled
(C2 in
circuit)
DC
Coupled
(C2
shorted)
3.3 V
430 Ω
750 Ω
CMOS
5 V CMOS
910 Ω
1.8K Ω
1
R1 should be chosen so that the input swing on the D input
with respect to D̄ is in the range of ±80 to ±1000 mV, per the
AC Characteristics table.
Recommended Component Values for CMOS Single Ended Inputs
June 2007 * REV - 23
www.azmicrotek.com
10
AZ10EL16VO
AZ100EL16VO
AZ10EL16VOD
AZ100EL16VOD
AZ10EL16VOT
AZ100EL16VOT
AZ10EL16VOU
AZ100EL16VOU
Q 1
10 VCC
Q 2
9 QHG
TSSOP 10
D 3
Q 1
D 2
8 QHG
D 4
7
VEE
VBB 5
6
EN
8 VCC
TSSOP 8
SOIC 8
VBB / D 3
6 QHG
5 VEE
EN 4
AZ100EL16VON
7 QHG
AZ100EL16VONB
MLP 8, 2x2mm
MLP 8, 2x2mm
Q
1
8
VCC
D
D
2
7
QHG
VBB / D
2
7
VCC
VBB / D
3
6
QHG
EN
3
6
QHG
EN
4
5
VEE
VEE
4
5
QHG
TOP VIEW
1
8
Q
TOP VIEW
MLP 8: Bottom Center Pad may be left open
or tied to VEE. Pin 4 is the VEE return.
AZ10/100EL16VOL
NC
1
D
2
D
3
VBB
4
Q
Q
NC
16
15
14
VCC
13
MLP 16,
3x3 mm
5
6
EN
NC
7
VEE
12
NC
11
QHG
10
QHG
9
NC
8
10K
MPL 16: Bottom Center Pad may be left
open or tied to VEE. Pin 7 is the VEE return.
June 2007 * REV - 23
www.azmicrotek.com
11
MLP 16 (L) Package and DIE:
10K/100K Selection
Connect pin/pad 10K to VEE to select
10K operation. Float (NC) pin/pad 10K
to select 100K operation. VEE
connection must be less than 1Ω.
Pin 6 of the MLP 16 package may be
connected to pin 7 (VEE) with no effect
on the circuit.
AZ10EL16VO
AZ100EL16VO
DIE PAD COORDINATES
AZ10/100EL16VO DIE:
EL16VO
A
B
L
M
J
DIE SIZE: 950u X 940u
DIE THICKNESS: 180u
C
D
K
BOND PAD: 85u X 85u
E
F
I
H
G
Note: Other die thicknesses available. Contact factory for further information.
PAD CENTER COORDINATES
NAME
A
B
C
D
E
F
G
H
I
J
K
L
M
PAD DESIGNATION
D
D̄
VBB
¯¯¯
EN
VEE
10K
Q̄HG
QHG
NC
VCC
VCC
Q
Q̄
NC = No connect, leave open.
June 2007 * REV - 23
www.azmicrotek.com
12
X(Microns)
-342.5
-342.5
-342.5
-342.5
-33.5
126.5
312.5
312.5
312.5
312.5
302.5
142.5
-140.5
Y(Microns)
312.5
144.5
-87.0
-255.0
-312.5
-312.5
-248.5
-98.5
51.5
201.5
342.5
342.5
342.5
AZ10EL16VO
AZ100EL16VO
PACKAGE DIAGRAM
MLP 8 2x2mm
Pin 1 Dot
By Marking
2.000±0.050
MLP 8
(2x2mm)
2.000±0.050
TOP VIEW
Pin 1 Identification
R0.100 TYP
0.350±0.050
0.250±0.050
0.500 bsc
8
1
7
6
2 1.200±0.050
exp. pad
3
5
4
0.600±0.050
exp. pad
BOTTOM VIEW
0.750±0.050
0.000-0.050
1
2
SIDE VIEW
Note: All dimensions are in mm
June 2007 * REV - 23
www.azmicrotek.com
13
3 4
0.203±0.025
1.750
Ref.
AZ10EL16VO
AZ100EL16VO
PACKAGE DIAGRAM
SOIC 8
MILLIMETERS
DIM
NOTES:
1.
DIMENSIONS D AND E DO NOT
INCLUDE MOLD PROTRUSION.
2.
MAXIMUM MOLD PROTRUSION
FOR D IS 0.15mm.
3.
MAXIMUM MOLD PROTRUSION
FOR E IS 0.25mm.
June 2007 * REV - 23
A
A1
A2
A3
bp
c
D
E
e
HE
L
Lp
Q
v
w
y
Z
θ
www.azmicrotek.com
14
MIN
MAX
0.75
0.25
1.45
0.10
1.25
0.25
0.36
0.19
4.8
3.8
0.49
0.25
5.0
4.0
1.27
5.80
6.20
1.05
0.40
0.60
1.00
0.70
0.25
0.25
0.10
0.30
0O
0.70
8O
INCHES
MIN
MAX
0.069
0.004
0.010
0.049
0.057
0.01
0.014
0.019
0.0075
0.0100
0.19
0.20
0.15
0.16
0.050
0.228
0.244
0.041
0.016
0.039
0.024
0.028
0.01
0.01
0.004
0.012
0.028
0O
8O
AZ10EL16VO
AZ100EL16VO
PACKAGE DIAGRAM
TSSOP 8
DIM
A
A1
A2
A3
bp
c
D
E
e
HE
L
Lp
v
w
y
Z
θ
NOTES:
1.
DIMENSIONS D AND E DO NOT
INCLUDE MOLD PROTRUSION.
2.
MAXIMUM MOLD PROTRUSION
FOR D IS 0.15mm.
3.
MAXIMUM MOLD PROTRUSION
FOR E IS 0.25mm.
June 2007 * REV - 23
www.azmicrotek.com
15
MILLIMETERS
MIN
MAX
1.10
0.05
0.15
0.80
0.95
0.25
0.25
0.45
0.15
0.28
2.90
3.10
2.90
3.10
0.65
4.70
5.10
0.94
0.40
0.70
0.10
0.10
0.10
0.35
0.70
6O
0O
AZ10EL16VO
AZ100EL16VO
PACKAGE DIAGRAM
TSSOP 10
MILLIMETERS
MIN
MAX
A
A1
A2
A3
bp
c
D1
E2
e
HE
L
Lp
v
w
y
Z
θ
NOTES:
1.
DIMENSIONS D AND E DO NOT
INCLUDE MOLD PROTRUSION.
2.
MAXIMUM MOLD PROTRUSION
FOR D IS 0.15mm.
3.
MAXIMUM MOLD PROTRUSION
FOR E IS 0.25mm.
June 2007 * REV - 23
www.azmicrotek.com
16
1.10
0.15
0.95
0.05
0.80
0.25
0.15
0.15
2.90
2.90
0.30
0.23
3.10
3.10
0.50
4.80
5.00
0.95
0.40
0.70
0.10
0.10
0.10
0.34
0O
0.67
6O
AZ10EL16VO
AZ100EL16VO
PACKAGE DIAGRAM
MLP 16 3x3mm
D
2.
INDEX AREA
(D/2 x E/2)
A
D
2
D2
D2/2
B
E
2
E
3x
e
E2/2
E2
2
e
2x
1
aaa C
2x
aaa C
TOP VIEW
bbb M C A B
5.
16 x b
L
3.
3x e
BOTTOM VIEW
ccc C
A3
A
4.
0.08 C
A1
SIDE
VIEW
NOTES:
1. DIMENSIONING AND TOLERANCING
CONFORM TO ASME T14-1994.
2. THE TERMINAL #1 AND PAD
NUMBERING CONVENTION SHALL
CONFORM TO JESD 95-1 SPP-012.
3. DIMENSION b APPLIES TO METALLIZED
PAD AND IS MEASURED BETWEEN 0.25
AND 0.30 mm FROM PAD TIP.
4. COPLANARITY APPLIES TO THE
EXPOSED PADS AS WELL AS THE
TERMINALS.
5. INSIDE CORNERS OF METALLIZED PAD
MAY BE SQUARE OR ROUNDED
June 2007 * REV - 23
www.azmicrotek.com
17
C
SEATING
PLANE
MILLIMETERS
DIM
A
A1
A3
b
D
D2
E
E2
e
L
aaa
bbb
ccc
MIN
MAX
0.80
1.00
0.05
0.00
0.25 REF
0.18
0.30
3.10
2.90
1.95
0.25
3.10
2.90
1.95
0.25
0.50 BSC
0.50
0.30
0.25
0.10
0.10
AZ10EL16VO
AZ100EL16VO
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc.
makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona
Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license
rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems
intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a
situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly
or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.
June 2007 * REV - 23
www.azmicrotek.com
18
Similar pages