BCD AZ78L05M 3-terminal positive linear regulator Datasheet

Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
General Description
Features
The AZ78LXX series are three terminal positive regulators with several fixed output voltages. These regulators can provide local on card regulation, eliminating
the distribution problems associated with single point
regulation. The AZ78LXX can be used in logic systems, instrumentation, HiFi, and other solid state electronic equipment. When used as a Zener diode/resistor
combination replacement, the AZ78LXX usually
results an effective output impedance improvement of
two orders of magnitude, and lower quiescent current.
·
·
·
·
·
·
Output Current up to 100 mA
Fixed Output Voltage of 5V, 8V, 9V and 12V
Output Voltage Tolerances of ± 5% over the Full
Temperature Range
Internal Short Circuit Current-Limiting
Internal Thermal Overload Protection
No External Components
Applications
With adequate heat sinking the AZ78LXX can deliver
100 mA output current. Current limiting is included to
limit the peak output current to a safe value. Thermal
protection is also provided. If internal power
dissipation becomes too high for the heat sinking
provided, the thermal shutdown circuit takes over
preventing the IC from overheating.
·
·
·
·
High Efficiency Linear Regulator
Post Regulation for Switching Supply
Microprocessor Power Supply
Mother Board I/O Power Supply
The AZ78LXX are available in the plastic TO-92,
SOIC-8, SOT-223 and SOT-89 packages.
TO-92
SOIC-8
SOT-223
SOT-89
Figure 1. Package Types of the AZ78LXX
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
1
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Pin Configuration
Z Package
(TO-92)
3
INPUT
2
GND
1
OUTPUT
H Package
(SOT-223)
GND
4
3
INPUT
2
GND
1
OUTPUT
Connect pin 4 to pin 2 or leave
pin 4 electrically isolated
M Package
(SOIC-8)
R Package
(SOT-89)
OUTPUT
1
8
INPUT
GND
2
7
GND
GND
3
6
GND
N/C
4
5
N/C
GND
4
3
INPUT
2
GND
1
OUTPUT
Figure 2. Pin Configuration of the AZ78LXX (Top View)
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
2
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Functional Block Diagram
3 (8)
1
INPUT
OUTPUT
A(B)
A for 3-pin
B for 8-pin
2, 4 (2, 3, 6, 7)
GND
Figure 3. Functional Block Diagram of the AZ78LXX
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
3
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Ordering Information
-
AZ78L
Package
TO-92
SOIC-8
SOT-89
SOT-223
Circuit Type
E1: Lead Free
Output Voltage
05: 5V
08: 8V
09: 9V
12: 12V
TR: Tape and Reel or Ammo
Temperature
Range
0 to 125oC
0 to 125oC
0 to 125oC
0 to 125oC
Blank: Tin Lead
Blank: Tube or Bulk
Package
Z: TO-92
R: SOT-89
H: SOT-223
M: SOIC-8
Part Number
Tin Lead
Marking ID
Lead Free
Tin Lead
Lead Free
Packing Type
AZ78L05Z
AZ78L05Z-E1
AZ78L05Z
AZ78L05Z-E1
Bulk
AZ78L05ZTR
AZ78L05ZTR-E1
AZ78L05Z
AZ78L05Z-E1
Ammo
AZ78L08Z
AZ78L08Z-E1
AZ78L08Z
AZ78L08Z-E1
Bulk
AZ78L08ZTR
AZ78L08ZTR-E1
AZ78L08Z
AZ78L08Z-E1
Ammo
AZ78L09Z
AZ78L09Z-E1
AZ78L09Z
AZ78L09Z-E1
Bulk
AZ78L09ZTR
AZ78L09ZTR-E1
AZ78L09Z
AZ78L09Z-E1
Ammo
AZ78L12Z
AZ78L12Z-E1
AZ78L12Z
AZ78L12Z-E1
Bulk
AZ78L12ZTR
AZ78L12ZTR-E1
AZ78L12Z
AZ78L12Z-E1
Ammo
AZ78L05M
AZ78L05M-E1
78L05M
78L05M-E1
Tube
AZ78L05MTR
AZ78L05MTR-E1
78L05M
78L05M-E1
Tape & Reel
AZ78L08M
AZ78L08M-E1
78L08M
78L08ZM-E1
AZ78L08MTR
AZ78L08MTR-E1
78L08M
78L08M-E1
Tube
Tape & Reel
AZ78L09M
AZ78L09M-E1
78L09M
78L09M-E1
Tube
AZ78L09MTR
AZ78L09MTR-E1
78L09M
78L09M-E1
Tape & Reel
AZ78L12M
AZ78L12M-E1
78L12M
78L12M-E1
Tube
AZ78L12MTR
AZ78L12ZMTR-E1
78L12M
78L12M-E1
Tape & Reel
AZ78L05RTR
AZ78L05RTR-E1
R78A
E78A
Tape & Reel
AZ78L08RTR
AZ78L08RTR-E1
R78B
E78B
Tape & Reel
AZ78L09RTR
AZ78L09RTR-E1
R78C
E78C
Tape & Reel
AZ78L12RTR
AZ78L12RTR-E1
R78D
E78D
Tape & Reel
AZ78L05HTR
AZ78L05HTR-E1
H78A
EH78A
Tape & Reel
AZ78L08HTR
AZ78L08HTR-E1
H78B
EH78B
Tape & Reel
AZ78L09HTR
AZ78L09HTR-E1
H78C
EH78C
Tape & Reel
AZ78L12HTR
AZ78L12HTR-E1
H78D
EH78D
Tape & Reel
BCD Semiconductor's Pb-free products, as designated with "E1" suffix in the part number, are RoHS compliant.
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
4
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Absolute Maximum Ratings (Note 1)
Parameter
Input Voltage
Operating Junction Temperature Range
Lead Temperature (Soldering, 10sec)
Power Dissipation (TA=25oC)
Storage Temperature Range
Symbol
Value
Unit
VCC
20
V
TJ
0 to125
o
TLEAD
265
o
PD
TSTG
C
C
TO-92
0.65
SOIC-8
0.6
SOT-223
0.7
SOT-89
0.65
W
-65 to 150
oC
300
V
ESD (Machine Model)
Note 1: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to
the device. These are stress ratings only, and functional operation of the device at these or any other conditions
beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended periods may affect device reliability.
Recommended Operating Conditions
Parameter
Operating Junction Temperature Range
Symbol
Min
Max
TJ
0
125
Unit
o
C
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
5
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Electrical Characteristics
AZ78L05 Electrical Characteristics
Limits in standard typeface are for TJ =25oC, Bold typeface applies over 0oC to 125oC, IO=40 mA, CI =0.33µF,
CO=0.1µF, VI =10V, unless otherwise specified.
Parameter
Output Voltage
Symbol
Conditions
VO
7.0V ≤ VI ≤ 15V
Min
Typ
Max
Unit
4.8
5
5.2
V
4.75
5.25
1.0mA ≤ IO ≤ 40mA (Note 2)
Line Regulation
VRLINE
7.0V ≤ VI ≤ 15V
18
75
mV
Load Regulation
VRLOAD
1.0mA ≤ IO ≤ 100mA
20
60
mV
3
5
mA
8.0V ≤ VI ≤ 15V
1.0
mA
1.0mA ≤ IO ≤ 40mA
0.1
Quiescent Current
Quiescent Current Change
Output Noise Voltage
Ripple Rejection
Peak Output Current
IQ
∆IQ
NO
10Hz ≤ f ≤ 100kHz (Note 3)
∆VI/ ∆VO
f=120Hz, 8.0V ≤ VI ≤ 15V
IPK
Average Temperature Coefficient of
Output Voltage
∆VO/ ∆T
Minimum Value of Input Voltage
Required to Maintain Line Regulation
VI(Min)
IO = 5.0mA
47
40
µV
62
dB
150
mA
-0.65
mV/ oC
6.7
7
V
Note 2: Power Dissipation ≤ 0.6W
Note 3: Recommended minimum load capacitance of 0.01µF to limit high frequency noise.
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
6
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Electrical Characteristics (Continued)
AZ78L08 Electrical Characteristics
Limits in standard typeface are for TJ =25oC, Bold typeface applies over 0oC to 125oC, IO=40 mA, CI =0.33µF,
CO=0.1µF, VI =14V, unless otherwise specified.
Parameter
Output Voltage
Symbol
Conditions
VO
11V ≤ VI ≤ 18V
Min
Typ
Max
Unit
7.7
8.0
8.3
V
7.6
8.4
1.0mA ≤ IO ≤ 40mA (Note 2)
Line Regulation
VRLINE
11V ≤ VI ≤ 18V
18
75
mV
Load Regulation
VRLOAD
1.0mA ≤ IO ≤ 100mA
20
90
mV
3
5
mA
11V ≤ VI ≤ 18V
1.5
mA
1.0mA ≤ IO ≤ 40mA
0.1
Quiescent Current
Quiescent Current Change
Output Noise Voltage
Ripple Rejection
Peak Output Current
IQ
∆IQ
NO
∆VI/ ∆VO
10Hz ≤ f ≤ 100kHz (Note 3)
f=120Hz, 11V ≤ VI ≤ 18V
IPK
Average Temperature Coefficient of
Output Voltage
∆VO/ ∆T
Minimum Value of Input Voltage
Required to Maintain Line Regulation
VI(Min)
IO = 5.0mA
39
60
µV
45
dB
150
mA
-0.8
mV/ oC
9.7
V
Note 2: Power Dissipation ≤ 0.6W
Note 3: Recommended minimum load capacitance of 0.01µF to limit high frequency noise.
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
7
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Electrical Characteristics (Continued)
AZ78L09 Electrical Characteristics
Limits in standard typeface are for TJ =25oC, Bold typeface applies over 0oC to 125oC, IO=40 mA, CI =0.33µF,
CO=0.1µF, VI =15V, unless otherwise specified.
Parameter
Output Voltage
Symbol
Conditions
VO
12V ≤ VI ≤ 18V
Min
Typ
Max
Unit
8.6
9
9.4
V
8.55
9.45
1.0mA ≤ IO ≤ 40mA (Note 2)
Line Regulation
VRLINE
12V ≤ VI ≤ 18V
18
75
mV
Load Regulation
VRLOAD
1.0mA ≤ IO ≤ 100mA
20
90
mV
3
5
mA
12V ≤ VI ≤ 18V
1.5
mA
1.0mA ≤ IO ≤ 40mA
0.1
Quiescent Current
Quiescent Current Change
Output Noise Voltage
Ripple Rejection
Peak Output Current
IQ
∆IQ
NO
∆VI/ ∆VO
10Hz ≤ f ≤ 100kHz (Note 3)
f=120Hz, 12V ≤ VI ≤ 18V
IPK
Average Temperature Coefficient of
Output Voltage
∆VO/ ∆T
Minimum Value of Input Voltage
Required to Maintain Line Regulation
VI(Min)
IO = 5.0mA
38
70
µV
44
dB
150
mA
-0.9
mV/ oC
10.7
V
Note 2: Power Dissipation ≤ 0.6W
Note 3: Recommended minimum load capacitance of 0.01µF to limit high frequency noise.
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
8
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Electrical Characteristics (Continued)
AZ78L12 Electrical Characteristics
Limits in standard typeface are for TJ =25oC, Bold typeface applies over 0oC to 125oC, IO=40 mA, CI =0.33µF,
CO=0.1µF, VI =18V, unless otherwise specified.
Parameter
Output Voltage
Symbol
Conditions
VO
15V ≤ VI ≤ 18V
Min
Typ
Max
Unit
11.5
12
12.5
V
11.4
12.6
1.0mA ≤ IO ≤ 40mA (Note 2)
Line Regulation
VRLINE
15V ≤ VI ≤ 18V
18
75
mV
Load Regulation
VRLOAD
1.0mA ≤ IO ≤ 100mA
20
90
mV
3
5
mA
15V ≤ VI ≤ 18V
1.5
mA
1.0mA ≤ IO ≤ 40mA
0.1
Quiescent Current
Quiescent Current Change
Output Noise Voltage
Ripple Rejection
Peak Output Current
IQ
∆IQ
NO
∆VI/ ∆VO
f=120Hz, 15V ≤ VI ≤ 18V
IPK
Average Temperature Coefficient of
Output Voltage
∆VO/ ∆T
Minimum Value of Input Voltage
Required to Maintain Line Regulation
VI(Min)
80
µV
54
dB
150
mA
-1.0
mV/ oC
13.7
V
10Hz ≤ f ≤ 100kHz (Note 3)
IO = 5.0mA
40
Note 2: Power Dissipation ≤ 0.6W
Note 3: Recommended minimum load capacitance of 0.01µF to limit high frequency noise.
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
9
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Typical Performance Characteristics
2.0
AZ78L05
VOUT=5V
o
TJ=25 C
Output Voltage (V)
4
Vin-Vout Input/output Differential Voltage (V)
5
Io=100mA
Io=40mA
3
Io=1mA
2
1
0
0
2
4
6
8
IO=40mA
1.8
IO=100mA
1.6
1.4
1.2
1.0
IO=1mA
0.8
0.6
AZ78L05
∆V=1%*VO
0.4
0.2
0.0
-40
10
-20
0
20
40
60
80
100
120
o
Junction Temperature ( C)
Input Voltage
VI input
voltage(V)(V)
Figure 4. Dropout Characteristics
Figure 5. Dropout Voltage vs. Junction Temperature
2.9
3.0
2.8
Input Bias Current (mA)
Quiescent Current (mA)
2.5
2.7
2.6
2.5
2.4
2.3
2.2
2.1
-40
AZ78L05
VIN=10V
IO=5mA
-20
0
20
2.0
1.5
AZ78L05
VOUT=5.0V
IO=40mA
1.0
o
TJ=25 C
0.5
40
60
80
100
0.0
120
0
o
2
4
6
8
10
12
14
16
18
20
Input Voltage (V)
Junction Temperature ( C)
Figure 6. Quiescent Current vs. Junction Temperature
Figure 7. Input Bias Current vs. Input Voltage
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
10
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Typical Performance Characteristics (Continued)
VIN from 10V to 11V
1
Power Dissipation(W)
No Heatsink
VOUT
VOUT=5.0V
Iload=40mA
0.1
o
RJA=250 C/W
o
PD(MAX) to25 C=0.6W
0
25
50
75
100
125
150
o
Ambient Temperature( C)
Figure 8. Maximum Power Dissipation vs.
Ambient Temperature (SOIC-8 Package)
Figure 9. Line Transient Response
ILOAD from 1mA to 50mA
VIN=10V
VOUT=5.0V
VOUT
25mA
Figure 10. Load Transient Response
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
11
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Typical Application
VIN
3
AZ78L05
VOUT
1
+
+
2
0.33µF
(Note 4)
0.1µF
(Note 4)
Note 4: Bypass capacitors are recommended for optimum stability and transient response and should be located
as close as possible to the regulator.
Figure 11. Typical Application of the AZ78LXX
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
12
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Mechanical Dimensions
TO-92
Unit: mm(inch)
1.100(0.043)
3.430(0.135)
MIN
3.700(0.146)
3.300(0.130)
1.400(0.055)
0.360(0.014)
0.510(0.020)
0.000(0.000)
0.380(0.015)
Φ1.600(0.063)
MAX
4.700(0.185)
0.380(0.015)
0.550(0.022)
14.100(0.555)
14.500(0.571)
4.300(0.169)
4.400(0.173)
4.700(0.185)
1.270(0.050)
TYP
2.440(0.096)
2.640(0.104)
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
13
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Mechanical Dimensions (Continued)
SOIC-8
Unit: mm(inch)
4.800(0.189)
5.000(0.197)
7°
0.320(0.013)
1.350(0.053)
1.750(0.069)
8°
8°
7°
0.675(0.027)
0.725(0.029)
D
5.800(0.228)
1.270(0.050)
6.200(0.244)
TYP
D
20:1
0.300(0.012)
R0.150(0.006)
0.100(0.004)
φ 0.800(0.031)
0.200(0.008)
0°
8°
1.000(0.039)
3.800(0.150)
4.000(0.157)
1°
5°
0.330(0.013)
0.510(0.020)
0.900(0.035)
R0.150(0.006)
0.190(0.007)
0.250(0.010)
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
14
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Mechanical Dimensions (Continued):
SOT-223
Unit: mm(inch)
6.300(0.248)
6.700(0.264)
)
0.250(0.010
)
4
1
0.350(0.0
2.900(0.114)
3.100(0.122)
0.900(0.035)
3.700(0.146)
3.300(0.130)
7.300(0.287)
6.700(0.264)
MIN
0.250(0.010)
1.750(0.069)
TYP
2.300(0.091)
0.610(0.024)
TYP
0.810(0.032)
4.500(0.177)
0°
10°
4.700(0.185)
0.020(0.001)
0.100(0.004)
1.500(0.059)
1.520(0.060)
1.700(0.067)
1.800(0.071)
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
15
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Mechanical Dimensions (Continued):
SOT-89
Unit: mm(inch)
4.400(0.173)
4.600(0.181)
1.630(0.064)
1.400(0.055)
1.600(0.063)
1.830(0.072)
0.000(0.000)
0.076(0.003)
1.400(0.055)*
1.200(0.047)
0.900(0.035)
3.950(0.156)
4.250(0.167)
R0.200(0.008)
2.300(0.091)
2.600(0.102)
3°
10°
0.360(0.014)
0.360(0.014)
0.360(0.014)
0.480(0.019)
0.480(0.019)
0.440(0.017)
0.440(0.017)
3.000(0.118)
0.560(0.022)
3°
10°
R0.150(0.006)
BCD Semiconductor Manufacturing Limited
Apr. 2005 Rev. 1. 3
16
http://www.bcdsemi.com
BCD Semiconductor Corporation
3170 De La Cruz Blvd, Suite # 105 Santa Clara, CA 95054-2411, U.S.A
Tel: +1-408-988 6388, Fax: +1-408-988 6386
Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.
800 Yi Shan Road, Shanghai 200233, PRC
Tel: +86-21-6485-1491, Fax: +86-21-5450-0008
Advanced Analog Circuits (Shanghai) Corporation
8F, B Zone, 900 Yi Shan Road, Shanghai 200233, PRC
Tel: +86-21-6495 9539, Fax: +86-21-6485 9673
BCD Semiconductor (Taiwan) Company Limited
Room 2210, 22nd Fl, 333, Keelung Road, Sec. 1, TaiPei (110), Taiwan
Tel: +886-2-2758 6828, Fax: +886-2-2758 6892
IMPORTANT NOTICE
BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifications herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for
use of any its products for any particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any
liability arising out of the application or use of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or other rights nor the rights of others.
Similar pages