Source B-15-13-1250C-FDFB-SSCA 1.25 gbps bi-directional sc receptacle single fiber transceiver Datasheet

1.25 Gbps bi-directional SC Receptacle
single Fiber Transceiver
B-1X/1X-1250C-F(DFB)-SSCx
Features
• Single Mode Single Fiber 2x5 SFF SC Receptacle connector
• Gigabit Ethernet Compliant
• Single +3.3V Power Supply
• Tx 1310nm/Rx 1550 nm [B-13/15-1250C-F(DFB)-SSCx]
• Tx 1550nm/Rx 1310 nm [B-15/13-1250C-F(DFB)-SSCx]
• LVPECL Differential Inputs and Outputs
• LVTTL Signal Detection Output
• Class 1 Laser Int. Safety Standard IEC-825 Compliant
• EMI Shielding Finger Optional
• RoHS compliance available
Absolute Maximum Rating
Parameter
Symbol
Min.
Max.
Unit
Vcc
0
3.6
V
-
0
Vcc
V
Iout
-
30
mA
-
-
260
ºC
Tstg
-40
85
ºC
Power Supply Voltage
Input Voltage
Output Current
Soldering Temperature
Storage Temperature
Note
10 seconds on leads only
Recommended Operating Condition
Parameter
Symbol
Min.
Typ.
Max.
Unit
Power Supply Voltage
Vcc
3.1
3.3
3.5
V
Operating Temperature (-SSCx(S))
Topr
-5
-
70
ºC
Operating Temperature (-SSCxA(S))
Topr
-40
-
85
ºC
-
-
1250
-
Mbps
Data Rate
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS796-Jan2407
Rev. A.3
1.25 Gbps bi-directional SC Receptacle
single Fiber Transceiver
B-1X/1X-1250C-F(DFB)-SSCx
Transmitter Specifications
Parameter
Optical
Symbol
Min
Typical
Max
Unit
Notes
Optical Transmit Power
Po
-9
-
-3
dBm
B-1X/1X-1250C-F(DFB)-SSC
Optical Transmit Power
Po
-5
-
0
dBm
B-1X/1X-1250C-FDFB-SSC2
Optical Transmit Power
Po
-3
-
+2
dBm
B-1X/1X-1250C-FDFB-SSC3
Optical Transmit Power
Output center Wavelength
Po
0
-
+5
dBm
B-1X/1X-1250C-FDFB-SSC4
λ
1260
1310
1360
nm
B-13/15-1250C-F(DFB)-SSCX
Output center Wavelength
λ
1480
1550
1580
nm
B-15/13-1250C-F(DFB)-SSCX
Output Spectrum Width
∆λrms
-
-
4
nm
RMS(σ), B-1X/1X-1250C-F-SSC
Output Spectrum Width
∆λ
-
-
1
nm
-20dB width, B-1X/1X-1250C-FDFB-SSCX
SMSR
30
-
-
dB
B-1X/1X-1250C-FDFB-SSCX
ER
9
-
-
dB
Side Mode Supression Ratio
Extinction Ratio
Output Eye
Compliant with IEEE 802.3z
Optical Rise Time
tr
-
-
260
ps
20% to 80% Values
Optical Fall Time
tf
-
-
260
ps
20% to 80% Values
Optical Isolation
30
-
-
dB
RIN
-
-
-116
dB/Hz
TJ
-
-
270
ns
Parameter
Electrical
Symbol
Min
Typical
Max
Unit
Supply Current
ICC
-
-
150
mA
Transmit Enable Voltage
VEN
0
-
0.8
V
Transmit Disable Voltage
VDIS
2
-
VCC
V
Data Input Current-Low
IIL
-350
-
-
µA
Data Input Current-High
IIH
-
-
350
µA
Differential Input Voltage
VIH-VIL
300
-
-
mV
Data Input Voltage-Low
VIL-VCC
-2.0
-
-1.58
V
Data Input Voltage-High
VIH-VCC
-1.1
-
-0.74
V
Relative Intensity Noise
Total Jitter
Measured with 27-1 PRBS
Transmitter Specifications
LUMINENTOIC.COM
Notes
Maximum current is specified at Vcc=
Maximum @ maximum temperature
These inputs are compatible with 10K, 10KH
and 100K ECL and PECL inputs
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS796-Jan2407
Rev. A.3
1.25 Gbps bi-directional SC Receptacle
single Fiber Transceiver
B-1X/1X-1250C-F(DFB)-SSCx
Receiver Specifications
Parameter
Optical
Sensitivity
Maximum Input Power
Symbol
Min
Typical
Max
Unit
-
-
-
-22
dBm
Pin
-3
-
-
dBm
Notes
Measured with 27-1 PRBS,BER= 10-12
Signal Detect-Asserted
Pa
-
-
-22
dBm
Measured on transition: low to high (Note 1)
Signal Detect-Deasserted
Pd
-38
-
-
dBm
Measured on transition: high to low (Note 1)
Signal Detect-Hysteresis
-
1
-
4
dB
Cross Talk
-
-
-
-33
dB
Wavelength of Operation
-
1480
-
1600
nm
B-13/15-1250C-F(DFB)-SSCX
Wavelength of Operation
-
1260
-
1360
nm
B-15/13-1250C-F(DFB)-SSCX
Max
Unit
Note
The current excludes the output load current
Note 1: The SD level should be deasserted when fiber disconnected
Receiver Specifications
Parameter
Electrical
Symbol
Min
Typical
ICC
-
-
100
mA
Data Output Voltage-Low
VOL -Vcc
-2.0
-
-1.58
V
Data Output Voltage-High
VOH- Vcc
-1.1
-
-0.74
V
Supply Current
Signal Detect Output Voltage-Low
VSDL
0
-
0.5
V
Signal Detect Output Voltage-High
VSDH
2.0
-
Vcc
V
LUMINENTOIC.COM
These outputs are compatible with 10K,
10KH and 100KECL and PECL outputs
LVTTL SD Output
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS796-Jan2407
Rev. A.3
1.25 Gbps bi-directional SC Receptacle
single Fiber Transceiver
B-1X/1X-1250C-F(DFB)-SSCx
Connection Diagram
PIN
Symbol
1
RxGND
Notes
Directly connect this pin to the receiver ground plane
2
RxVcc
+3.3V dc power for the receiver section
3
SD
Active high on this indicates a received optical signal(LVTTL)
4
RD-
Receiver Data Out Bar(LVPECL)
5
RD+
Receiver Data Out (LVPECL)
6
TxVcc
7
TxGND
+3.3V dc power for the transmitter section
Directly connect this pin to the tranmitter ground plane
8
Warnings
TxDIS
9
TD+
Transmitter Data In (LVPECL)
10
TD-
Transmitter Data In Bar (LVPECL)
LUMINENTOIC.COM
Transmitter disable(LVTTL)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS796-Jan2407
Rev. A.3
1.25 Gbps bi-directional SC Receptacle
single Fiber Transceiver
B-1X/1X-1250C-F(DFB)-SSCx
Recommended Circuit Schematic
PHY DEVICE
TERMINATE AT
TRANSCEIVER INPUTS
Vcc(+3.3V)
Z=50�
TD-
LVPECL
100�
Z=50�
TD+
130�
1
2
3
TxGND
TxVcc
RD-
RD+
6
TxDIS
7
Tx Disable
SD
TD+
RxVcc
Rx
8
TD-
Tx
9
RxGND
10
4
130�
1�H
Vcc(+3.3V)
C2
C3
10�F
Vcc(+3.3V)
1�H
C1
5
LVTTL
RD+
Z=50�
LVPECL
100�
RD-
Z=50�
130�
Vcc(+3.3V)
130�
Z=50�
SD
LVTTL
NOTE:C1=C2=C3=100nF
TERMINATE AT
DEVICE INPUTS
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS796-Jan2407
Rev. A.3
1.25 Gbps bi-directional SC Receptacle
single Fiber Transceiver
B-1X/1X-1250C-F(DFB)-SSCx
Recommended Circuit Board Layout
DIMENSION IN MILLIMETER (INCHES)
NOTES:
1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER.
2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL
TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS.
3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS796-Jan2407
Rev. A.3
1.25 Gbps bi-directional SC Receptacle
single Fiber Transceiver
B-1X/1X-1250C-F(DFB)-SSCx
Package Diagram
B-1X/1X-1250C-F(DFB)-SSCX(A)
Units: mm
Warnings
Housing Lead
PIN 1
PIN 5
Legal Notice
Housing Lead
Stud Stand-off
LUMINENTOIC.COM
Stand-off
PIN 10
PIN 6
Stand-off
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS796-Jan2407
Rev. A.3
1.25 Gbps bi-directional SC Receptacle
single Fiber Transceiver
B-1X/1X-1250C-F(DFB)-SSCx
Package Diagram
B-1X/1X-1250C-F(DFB)-SSCX(A)S
Units: mm
Matel Finger
Stand-off
PIN 1
PIN 5
Stand-off
Housing Lead
Stud
PIN 6
PIN 10
Stand-off
Housing Lead
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
8
LUMNDS796-Jan2407
Rev. A.3
1.25 Gbps bi-directional SC Receptacle
single Fiber Transceiver
B-1X/1X-1250C-F(DFB)-SSCx
Ordering Information
Available Options:
B-13/15-1250C-F-SSC(A)(S)(-G5)
B-13/15-1250C-FDFB-SSC(S)(-G5)
B-13/15-1250C-FDFB-SSC2(S)(-G5)
B-13/15-1250C-FDFB-SSC3(S)(-G5)
B-13/15-1250C-FDFB-SSC4(S)(-G5)
B-15/13-1250C-F-SSC(A)(S)(-G5)
B-15/13-1250C-FDFB-SSC(S)(-G5)
B-15/13-1250C-FDFB-SSC2(S)(-G5)
B-15/13-1250C-FDFB-SSC3(S)(-G5)
B-15/13-1250C-FDFB-SSC4(S)(-G5)
Part numbering Definition:
B - 1X/1X - 1250C - F(DFB) - S SC Tx Power Operating Temperature Shielding Finger RoHS compliance available
• Wavelength
13/15: Tx Wavelength=1310nm
Rx Wavelength=1550nm
15/13: Tx Wavelength=1550nm
Rx Wavelength=1310nm
• Communication protocol
(1.25 Gbps)
• +3.3 V SFF Transceiver
F= FP Laser transceiver
FDFB = DFB Laser transceiver
• Single mode fiber
• Connector options
• Tx Output Power
blank = -9 to -3 dBm
2 = -5 to 0 dBm
3 = -3 to +2 dBm
4 = 0 to +5 dBm
• Operating Temperature
blank = Commercial temperature (-5 to 70 ºC)
A = Industrial temperature (-40 to 85 ºC)
• Shielding Finger Option
Blank = No shielding finger
S = with Shielding finger
• RoHS compliance available
Blank = RoHS non-compliant product
G5 = RoHS 5/6-compliant product (lead exemption)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
9
LUMNDS796-Jan2407
Rev. A.3
1.25 Gbps bi-directional SC Receptacle
Single Fiber Transceiver
B-1X/1X-1250C-F(DFB)-SSCx
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
10
LUMNDS796-Jan2407
Rev. A.3
Similar pages