Littelfuse B1100C Battrax slic protector Datasheet

Battrax SLIC Protector
Battrax SLIC Protector
This solid state protection device can be referenced to either a positive or negative voltage
source. The B1xx0C_ is for a -VREF and the B2050C_ is for a +VREF. Designed using an
SCR and a gate diode, the B1xx0C_ Battrax begins to conduct at |-VREF| + |-1.2 V| while the
B2050C_ Battrax begins to conduct at |+VREF| + |1.2 V|.
For a diagram of a Battrax application, see Figure 3.38.
Pin 3
(+VREF)
Pin 2
(Ground)
Pin 1
(Line)
Pin 3
(-VREF)
Gate
Pin 1
(Line)
Pin 2
(Ground)
+Battrax
B2050C_
-Battrax
B1xx0C_
Electrical Parameters
Part
Number *
VDRM
Volts
VS
Volts
VT
Volts
IDRM
µAmps
IGT
mAmps
IT
Amps
IH
mAmps
CO
pF
B1100C_
|-VREF| + |-1.2 V|
|-VREF| + |-10 V|
4
5
100
2.2
100
50
B1160C_
|-VREF| + |-1.2 V|
|-VREF| + |-10 V|
4
5
100
2.2
160
50
B1200C_
|-VREF| + |-1.2 V|
|-VREF| + |-10 V|
4
5
100
2.2
200
50
B2050C_
|+VREF| + |1.2 V|
|+VREF| + |10 V|
4
5
50
2.2
50
50
* For individual “CA” and “CC” surge ratings, see table below.
General Notes:
• All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range.
• IPP is a repetitive surge rating and is guaranteed for the life of the product.
• IPP ratings assume VREF = ±48 V.
• VDRM is measured at IDRM.
• VS is measured at 100 V/µs.
• Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias and is a typical value. “CC” product is approximately 2x the listed
value.
• Positive Battrax information is preliminary data.
• VREF maximum value for the negative Battrax is -200 V.
• VREF maximum value for the positive Battrax is 110 V.
Surge Ratings
Series
IPP
2x10 µs
Amps
IPP
8x20 µs
Amps
IPP
10x160 µs
Amps
IPP
10x560 µs
Amps
IPP
10x1000 µs
Amps
ITSM
60 Hz
Amps
di/dt
Amps/µs
A
150
150
90
60
50
20
500
C
500
400
200
150
100
50
500
http://www.littelfuse.com
+1 972-580-7777
2 - 50
© 2004 Littelfuse, Inc.
SIDACtor® Data Book and Design Guide
Battrax SLIC Protector
Thermal Considerations
Package
Symbol
Modified DO-214AA
TJ
Operating Junction Temperature Range
-40 to +150
°C
TS
Storage Temperature Range
-65 to +150
°C
85
°C/W
Pin 3
(VREF)
Parameter
Thermal Resistance: Junction to Ambient
RθJA
Pin 1
(Line)
Value
Unit
Data Sheets
Pin 2
(Ground)
+I
+I
+I
IT
IT
VS VDRM
-V -V
IS
IH
IGT
IH
VT
IDRM
IDRM
VT
IDRM
VDRM
IH
IGT
-V
+V+V
+V
VDRM VS
VT
VS
IT
-I
-I
-I
V-I Characteristics for Negative Battrax
V-I Characteristics for Positive Battrax
6
4
IH
8
25 ˚C
2
IH (TC = 25 ˚C)
10
Ratio of
Percent of VS Change – %
14
12
0
-4
2.0
1.8
1.6
1.4
25 ˚C
1.2
1.0
0.8
0.6
0.4
-40 -20 0
-6
20 40 60 80 100 120 140 160
Case Temperature (TC) – ˚C
-8
-40 -20 0 20 40 60 80 100 120 140 160
Junction Temperature (TJ) – ˚C
Normalized VS Change versus Junction Temperature
© 2004 Littelfuse, Inc.
SIDACtor® Data Book and Design Guide
Normalized DC Holding Current versus Case Temperature
2 - 51
http://www.littelfuse.com
+1 972-580-7777
Similar pages