MORNSUN B1212XT-1W Single output, smd dc-dc converter Datasheet

B_(X)T-1W Series
1W,FIXED INPUT, ISOLATED & UNREGULATED
SINGLE OUTPUT, SMD DC-DC CONVERTER
FEATURES
PRODUCT PROGRAM
SMD Package Style
Industry Standard Pinout
No Heat sink Required
1KVDC Isolation
High Power Density
Internal SMD construction
Temperature Range: -40°C to +85°C
No External Component Required
RoHS Compliance
Input
Part
Number
Nominal
Range
3.3
3.0-3.6
in a distributed power supply system on a circuit
board.
1) Where the voltage of the input power
supply is fixed (voltage variation ≤ ±10%);
2) Where isolation is necessary between
output
(isolation
voltage
Max
UL CE
Min
303
30
73
UL
20
74
UL
B0503(X)T-1W
3.3
303
30
72
B0505(X)T-1W
5
200
20
77
UL,CE
9
111
12
76
UL,CE
B0512(X)T-1W
12
84
9
79
UL,CE
B0515(X)T-1W
15
67
7
78
UL,CE
B1205(X)T-1W
5
200
20
69
UL,CE
B1209(X)T-1W
9
111
12
73
UL,CE
12
84
9
73
UL,CE
UL,CE
5
12
4.5-5.5
10.8-13.2
B1215(X)T-1W
15
67
7
74
B2403(X)T-1W
3.3
300
30
69
B2405(X)T-1W
5
200
20
70
B2409(X)T-1W
9
110
11
72
12
83
8
75
B2415(X)T-1W
15
67
7
76
B2424(X)T-1W
24
42
4
77
B2412(X)T-1W
These products apply to:
Efficiency
(%, Typ.)
Current (mA)
200
B1212(X)T-1W
supplies are isolated from the input power supply
Voltage
(VDC)
5
B0509(X)T-1W
for applications where a group of polar power
Output
3.3
B0305(X)T-1W
The B_(X)T-1W Series are specially designed
and
Voltage (VDC)
B0303(X)T-1W
APPLICATIONS
input
multi-country patent protection RoHS
24
21.6-26.4
Note: 1.the B_XT-1W series have no 3,6,7 pin. For example B0505XT-1W.
2. B_XT-1W series : UL-60950-1 pending.
≤1000VDC);
3) Where the regulation of the output voltage
and
the
output
ripple
noise
are
not
demanding.
Such as: purely digital circuits, ordinary low
ISOLATION SPECIFICATIONS
Item
Test Conditions
Min
Typ.
Max
Units
Isolation voltage
Tested for 1 minute and 1mA max
1000
VDC
Isolation resistance
Test at 500VDC
1000
MΩ
frequency analog circuits, and IGBT power
device driving circuits.
OUTPUT SPECIFICATIONS
Item
Test Conditions
Min
Output power
Line regulation
MODEL SELECTION
Ra ted Power
Pac ka ge Style
Ou t put Voltage
Inp ut Voltage
Pro duct Series
Load regulation
MORNSUN Science& Technology co.,Ltd.
W
15
20
10% to 100% load (5V output)
12.8
15
10% to 100% load (9V output)
8.3
10
10% to 100% load (12V output)
6.8
10
10% to 100% load (15V output)
6.3
10
10% to 100% load (24V output)
5
10
%
See tolerance envelope graph
Temperature drift
100% full load
Output ripple &Noise*
20MHz Bandwidth
Switching frequency
Units
1
±1.2
For Vin change of 1%(Others output)
Output voltage accuracy
Address: 2th floor 6th building, Huangzhou Industrial
District, Guangzhou, China
Tel: 86-20-38601850
Fax:86-20-38601272
Http://www.mornsun-power.com
Max
±1.5
For Vin change of 1%(3.3V output)
10% to 100% load (3.3V output)
B0505(X)T-1W
Typ.
0.1
50
Full load, nominal input(5/12V)
100
Full load, nominal input(24V)
500
0.03
%/°C
100
mVp-p
KHz
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
Note:
1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load unless
otherwise specified.
2. See below recommended circuits for more details.
MORNSUN reserves the copyright
Specifications subject to change without notice.
B_(X)T-1W
A/2-2008
Page 1 of 2
COMMON SPECIFICATION
Item
APPLICATION NOTE
Test Conditions
Min
Typ
Storage humidity
Max
Units
95
%
Operating temperature
-40
85
Storage temperature
-55
125
Temp. rise at full load
15
Lead temperature
reliably, During operation, the minimum output load
°C
25
1.5mm from case for 10 seconds
load! If the actual output power is very small, please
Free air convection
Package material
connect a resistor with proper resistance at the
Epoxy Resin(UL94V-0)
Short circuit protection*
1
MTBF
3500
Weight
is not less than 10% of the full load, and that this
product should never be operated under no
260
Cooling
Requirement on output load
To ensure this module can operate efficiently and
output end in parallel to increase the load.
s
K Hours
Recommended testing circuit
If you want to further decrease the input/output
g
ripple, an “LC” filtering network may be connected
1.41
*Supply voltage must be discontinued at the end of short circuit duration.
to the input and output ends of the DC/DC
converter, see (Figure 1).
TYPICAL CHARACTERISTICS
Single Output
L
L
+Vo
Vin
Cout
DC DC
Cin
GND
0V
(Figure 1)
It should also be noted that the inductance and
the frequency of the “LC” filtering network should be
staggered with the DC/DC frequency to avoid
mutual interference. However, the capacitance of
the output filter capacitor must be proper. If the
Operating Temp.(oC)
capacitance is too big, a startup problem might
arise. For every channel of output, provided the safe
RECOMMENDED REFLOW SOLDERING PROFILE
2 50
Te m p e ra tu r e ( o C)
and reliable operation is ensured, the greatest
capacitance of its filter capacitor sees (Table 1).
o
26 0 C
10 Sec Max
EXTERNAL CAPACITOR TABLE (Table 1)
22 0o C
2 00
1 50
90 Se c Ma x
( >22 0 oC )
1 00
4.13
(0.163)
6.25
(0.246)
6.00
(0.236)
First Angle Projection
RECOMMENDED FOOTPRINT
Top view,grid:2.54*2.54mm(0.1*0.1inch)
B_T-1W
8 7 6 5
7.50
(0.295)
11.2 MAX
(0.441)
12.70 (0.500)
7.62
(0.300)
2.00
(0.079)
0.60±0.05
(0.024±0.002)
6.76
(0.266)
A
7.19
(0.283)
1 2 3 4
B_(X)T-1W
9
4.7
0.47
12
2.2
-
-
15
1
-
-
24
0.47
0.30
(0.012)
regulation,
over-voltage
and
over-current
protection is a linear voltage regulator with
overheat protection that is connected to the input
or output end in series (Figure2).
8
1 2
5
4
(0.039)
(Top view)
2.54±0.1
(0.100±0.004)
1.85MAX
(0.073)
2.2
24
Output Voltage Regulation and Over-voltage
Protection Circuit
The simplest device for output voltage
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
2.54
0.25
(0.100) (0.100)
Cout
(uF)
10
It’s not recommend to connect any external capacitor in the
application field with less than 0.5 watt output.
Time ( s ec .)
(Side view)
Vout
(VDC)
3.3/5
12
50
0
Cin
(uF)
4.7
Vin
(VDC)
3.3/5
FOOTPRINT DETAILS
Pin Function(T) Function(XT)
GND
GND
1
Vin
Vin
2
0V
4
0V
+Vo
+Vo
5
No Pin
3,6,7
NC
NC
NC
8
NC:No Connection
Vin
+Vout
REG
DC DC
GND
0V
REG
Vin
GND
+Vout
DC DC
0V
(Figure2)
Overload Protection
Under normal operating conditions, the output
circuit of these products has no protection against
over-current
and
short-circuits.
The simplest
method is to connect a self-recovery fuse in series
0.50 (0.020)
1.35MAX
(0.053)
5.00 。
MORNSUN reserves the copyright
Note:
Unit:mm(inch)
Pin section:0.60*0.25mm(0.024*0.010inch)
Pin tolerances: +0.10mm( +0.004inch)
General tolerances: +0.15mm( +0.006inch)
Specifications subject to change without notice.
at the input end or add a circuit breaker to the
circuit.
No parallel connection or plug and play.
B_(X)T-1W
A/2-2008
Page 2 of 2
Similar pages