EVERLIGHT B6C

EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
0603 Package Chip LED (0.2mm Height)
19-219/B6C-ZN1P2TY/3T
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Pb-free.
․The product itself will remain within RoHS
compliant version.
․The maximum height is 0.25mm.
․The component weight is approximately 0.68 mg
Descriptions
․The 19-219 SMD Taping is much smaller than
lead frame type components, thus enable smaller
board size, higher packing density, reduced
storage space and finally smaller equipment to be
obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Part No.
19-219/B6C-ZN1P2TY/3T
Chip
Material
InGaN
Emitted Color
Lens Color
Blue
Water Clear
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 1 of 9
Device No. : DSE- 199-B01
Prepared date: 29-Nov-2006
Prepared by: Jay Chou
EVERLIGHT ELECTRONICS CO.,LTD.
19-219/B6C-ZN1P2TY/3T
Package Outline Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 2 of 9
Device No. : DSE- 199-B01
Prepared date: 29-Nov-2006
Prepared by: Jay Chou
EVERLIGHT ELECTRONICS CO.,LTD.
19-219/B6C-ZN1P2TY/3T
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
10
mA
IFP
30
mA
Power Dissipation
Pd
40
mW
Electrostatic Discharge(HBM)
ESD
1000
V
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +90
℃
Soldering Temperature
Tsol
Peak Forward Current
(Duty 1/10 @1KHz)
Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Luminous Intensity
Iv
28.5
-----
72
mcd
Viewing Angle
2θ1/2
-----
120
-----
deg
Peak Wavelength
λp
-----
468
-----
nm
Dominant Wavelength
λd
465
-----
475
nm
Spectrum Radiation
Bandwidth
△λ
-----
35
-----
nm
Forward Voltage
VF
2.60
----
3.0
V
Reverse Current
IR
-----
-----
50
μA
Condition
IF=5mA
VR=5V
Notes:
1.Tolerance of Luminous Intensity ±10%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.05V
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 3 of 9
Device No. : DSE- 199-B01
Prepared date: 29-Nov-2006
Prepared by: Jay Chou
EVERLIGHT ELECTRONICS CO.,LTD.
19-219/B6C-ZN1P2TY/3T
Bin Range Of Dom. Wavelength
Group
Z
Bin
Min
Max
X
465
470
Y
470
475
Unit
Condition
nm
IF=5mA
Bin Range Of Luminous Intensity
Bin
Min
Max
N1
28.5
36.0
N2
36.0
45.0
P1
45.0
57.0
P2
57.0
72.0
Unit
Condition
mcd
IF=5mA
Bin Range Of Forward Voltage
Group
T
Bin
Min
Max
28
2.60
2.70
29
2.70
2.80
30
2.80
2.90
31
2.90
3.00
Unit
Condition
V
IF=5mA
Notes:
1.Tolerance of Luminous Intensity ±10%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.05V
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 4 of 9
Device No. : DSE- 199-B01
Prepared date: 29-Nov-2006
Prepared by: Jay Chou
EVERLIGHT ELECTRONICS CO.,LTD.
19-219/B6C-ZN1P2TY/3T
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 5 of 9
Device No. : DSE- 199-B01
Prepared date: 29-Nov-2006
Prepared by: Jay Chou
EVERLIGHT ELECTRONICS CO.,LTD.
19-219/B6C-ZN1P2TY/3T
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm, Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 6 of 9
Device No. : DSE- 199-B01
Prepared date: 29-Nov-2006
Prepared by: Jay Chou
EVERLIGHT ELECTRONICS CO.,LTD.
19-219/B6C-ZN1P2TY/3T
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level:90%
LTPD:10%
Test
Sample
Hours/Cycles
Size
No.
Items
Test Condition
1
Reflow Soldering
Temp. : 260℃±5℃
Min. 5sec.
6 Min.
22 PCS.
0/1
Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles
22 PCS.
0/1
Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles
22 PCS.
0/1
Temp. : 100℃
1000 Hrs.
22 PCS.
0/1
Temp. : -40℃
1000 Hrs.
22 PCS.
0/1
2
3
4
5
High Temperature
Storage
Low Temperature
Storage
Ac/Re
6
DC Operating Life
IF = 5 mA
1000 Hrs.
22 PCS.
0/1
7
High Temperature /
High Humidity
85℃/ 85%RH
1000 Hrs.
22 PCS.
0/1
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 7 of 9
Device No. : DSE- 199-B01
Prepared date: 29-Nov-2006
Prepared by: Jay Chou
EVERLIGHT ELECTRONICS CO.,LTD.
19-219/B6C-ZN1P2TY/3T
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30 deg C or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 8 of 9
Device No. : DSE- 199-B01
Prepared date: 29-Nov-2006
Prepared by: Jay Chou
EVERLIGHT ELECTRONICS CO.,LTD.
19-219/B6C-ZN1P2TY/3T
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable,
a double-head soldering iron should be used (as below figure). It should be confirmed beforehand
whether the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1
Page: 9 of 9
Device No. : DSE- 199-B01
Prepared date: 29-Nov-2006
Prepared by: Jay Chou