EPCOS B78148T3821K000 Rf chokes, mcc series ceramic or ferrite cylinder core Datasheet

Inductors
RF chokes, MCC series
Series/Type:
B78108T*, B78148T*
The following products presented in this data sheet are being withdrawn.
Ordering Code
B78108T3*/B78148T3*
Substitute Product
Date of Withdrawal
2012-10-19
Deadline Last
Orders
2013-01-31
Last Shipments
2013-04-30
For further information please contact your nearest EPCOS sales office, which will also support you in selecting a
suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales.
RF chokes
B78108T, B78148T
MCC series, 3.3 x 7 (mm)
MCC choke (Mini Cylinder Core)
Rated inductance 0.1 ... 100 μH
Rated current 85 ... 1120 mA
Construction
■ Ceramic or ferrite cylinder core
■ Winding: enamel copper wire
■ Flame-retardant lacquer coating
B78108T
Features
■
■
■
■
■
Low total height
Low inductance
High resonance frequency
Suitable for wave soldering
RoHS-compatible
Applications
B78148T
■ RF blocking
■ Decoupling and interference suppression
■ For antenna systems, automotive electronics,
telecommunications, entertainment electronics
Terminals
■ Central axial leads (B78108T)
■ Radially bent to 5 mm lead spacing (B78148T)
■ B781*T3:
– Base material Staku 30/copper-clad steel 30
– Hot-dipped and electro-plated with pure tin
■ B781*T1:
– Base material CuAg0.1
– Electroplated with nickel and pure tin
Marking
Inductance indicated by color bands to IEC 60062
Delivery mode and packing units
■ Taped, Ammo and reel packing
■ Packing units:
Ammo
(pcs./pack.)
Reel
(pcs./reel)
Axial
5000
5000
Radial
2500
2000
Please read Cautions and warnings and
Important notes at the end of this document.
2
06/12
RF chokes
B78108T, B78148T
MCC series, 3.3 x 7 (mm)
Dimensional drawings
B78108T (axial leads, taped)
Dimensions in mm
7 max.
(IEC 60294)
3.5 min.
6±0.5
5±0.25 5±0.25
ø3.3 max.
ø0.6 max.
65±1
53±2
9.8 max.
lacquered
Minimum lead spacing 10 mm
IND0427-U-E
2 max.
1.3 max.
insulated
Thickness of tape
0.7±0.2
16±0.5
_ 0.5
9 +0.75
6 min.
_ 0.5
18 +1
0.5 max.
9.8 max.
lacquered
0.6 max.
29 max.
1.3 max.
2 max.
7 max.
ø3.3 max.
(IEC 60294)
B78148T (central radial leads, taped)
_ 0.1
5 +0.6
3.8±0.7
IND0629-B
4±0.2
12.7±0.3
IND0630-V-E
n
w
30
H
30
ø360 _ 1
ø30.5±0.15
ø82+1
ø90
Packing
Label
L
30
W
IND0452-V-E
L u W u H (max. mm):
Axial: 310 u 75 u 120, radial: 340 u 50 u 210
n (mm): Axial 72 +1, radial 42 +1
w (mm): Axial 84 max., radial 54 max.
Please read Cautions and warnings and
Important notes at the end of this document.
IND0631-B-E
3
06/12
RF chokes
B78108T, B78148T
MCC series, 3.3 x 7 (mm)
Technical data and measuring conditions
Rated inductance LR
Measured with LCR meter Agilent 4284A
or impedance analyzer Agilent 4294A
= 1 MHz
Measuring frequency:
LRd 10 PH
10 PH < LR d 4700 PH = 100 kHz
Measuring current:
d 1 mA
Measuring temperature: +20 °C
Q factor Qmin
Measured with precision impedance analyzer Agilent 4294A,
+20 °C
Rated temperature TR
+40 qC
Rated current IR
Maximum permissible DC current at rated temperature
Inductance decrease 'L/L0
d10% (referred to initial value) at IR, +20 qC
DC resistance Rmax
Measured at +20 qC
Resonance frequency fres,min Measured with Agilent 4294A or 8753ES, +20 °C
Solderability (lead-free)
Sn95.5Ag3.8Cu0.7: +(245 r5) °C, (3 r0.3) s
Wetting of soldering area t90%
(to IEC 60068-2-20, test Ta)
Resistance to soldering heat
+(260 r5) °C, 10 s (to IEC 60068-2-20, test Tb)
Tensile strength of leads
t20 N (to IEC 60068-2-21, test Ua)
Climatic category
55/125/56 (to IEC 60068-1)
Storage conditions
Mounted: –55 °C … +125 °C
Packaged: –25 °C … +40 °C, d75% RH
Weight
Approx. 0.25 g
Mounting information
When bending the leads, take care that the start-of-winding areas at the face ends (protected by
glue and lacquer) are not subjected to any mechanical stress.
Please read Cautions and warnings and
Important notes at the end of this document.
4
06/12
RF chokes
B78108T, B78148T
MCC series, 3.3 x 7 (mm)
Characteristics and ordering codes
fQ
IR
Rmax
fres,min
MHz
mA
:
MHz
Ordering code 2)
(reel packing)3)
40
25.2
1120
0.13
600
B781*8T3101K000
0.12
40
25.2
1080
0.145
570
B781*8T3121K000
0.15
38
25.2
1020
0.155
500
B781*8T3151K000
0.18
35
25.2
1000
0.17
460
B781*8T3181K000
0.22
35
25.2
990
0.195
420
B781*8T3221K000
0.27
35
25.2
910
0.215
380
B781*8T3271K000
0.33
35
25.2
830
0.24
330
B781*8T3331K000
0.39
35
25.2
790
0.27
300
B781*8T3391K000
0.47
35
25.2
750
0.315
280
B781*8T3471K000
0.56
35
25.2
700
0.34
260
B781*8T3561K000
0.68
35
25.2
530
0.48
240
B781*8T3681K000
0.82
35
25.2
500
0.55
230
B781*8T3821K000
LR
Tolerance1)
Qmin
PH
Ceramic cylinder core
0.10
r10%
^
K
1) Closer tolerances on request.
2) Replace the * by code number »0« for axial taping or by »4« for radial taping.
3) For Ammo pack the last digit has to be a »9«. Example: B78108T3101K009
Please read Cautions and warnings and
Important notes at the end of this document.
5
06/12
RF chokes
B78108T, B78148T
MCC series, 3.3 x 7 (mm)
Characteristics and ordering codes
Tolerance1)
LR
Qmin
PH
fQ
IR
Rmax
fres,min
Ordering code 2)
MHz
mA
:
MHz
(reel packing)3)
25.2
630
0.25
180
B781*8T1102K000
Ferrite cylinder core
1.0
r10%
^
K
35
1.2
40
7.96
610
0.25
170
B781*8T1122K000
1.5
40
7.96
570
0.30
150
B781*8T1152K000
1.8
40
7.96
540
0.30
130
B781*8T1182K000
2.2
40
7.96
520
0.35
120
B781*8T1222K000
2.7
40
7.96
480
0.40
110
B781*8T1272K000
3.3
40
7.96
420
0.50
110
B781*8T1332K000
3.9
40
7.96
400
0.55
100
B781*8T1392K000
4.7
40
7.96
380
0.65
90
B781*8T1472K000
5.6
45
7.96
260
1.30
75
B781*8T1562K000
6.8
45
7.96
250
1.45
70
B781*8T1682K000
8.2
50
7.96
240
1.60
65
B781*8T1822K000
10
50
7.96
230
1.70
60
B781*8T1103K000
12
55
2.52
190
2.40
50
B781*8T1123K000
15
55
2.52
185
2.70
45
B781*8T1153K000
18
55
2.52
175
2.90
40
B781*8T1183K000
22
60
2.52
170
3.20
30
B781*8T1223K000
27
60
2.52
160
3.60
27
B781*8T1273K000
33
60
2.52
150
4.10
24
B781*8T1333K000
39
60
2.52
140
4.50
22
B781*8T1393K000
47
60
2.52
100
8.50
20
B781*8T1473K000
56
60
2.52
100
8.80
18
B781*8T1563K000
68
60
2.52
95
10.0
15
B781*8T1683K000
82
60
2.52
90
11.5
14
B781*8T1823K000
100
60
2.52
85
12.5
11
B781*8T1104K000
1) Closer tolerances on request.
2) Replace the * by code number »0« for axial taping or by »4« for radial taping.
3) For Ammo pack the last digit has to be a »9«. Example: B78108T3101K009
Please read Cautions and warnings and
Important notes at the end of this document.
6
06/12
RF chokes
B78108T, B78148T
MCC series, 3.3 x 7 (mm)
Impedance |Z| versus frequency f
measured with impedance analyzer Agilent
4294A or S-parameter network analyzer
Agilent 8753ES, typical values at +20 °C
Inductance L versus DC load current IDC
measured with LCR meter Agilent 4284A,
typical values at +20 °C
IND0112-N
10 6
Ω B781*8T
IND0113-B
10 3
B781*8T
μH
L
|Z| 10 5
100 μH
10 2
10 4
10 μH
10 1
10 3
1 μH
10 0
10 2
0.1 μH
1 μH
10 μH
100 μH
10 1
10 0 6
10
10
7
10
8
Hz 10
f
10
10
9
_2
10
_2
10
_1
10 0
A 10 1
I DC
Current derating Iop/IR
versus ambient temperature TA
(rated temperature TR = +40 qC)
Q factor versus frequency f
measured with impedance analyzer
Agilent 4294A, typical values at +20 °C
IND0114-H
100
0.1 μH
_1
IND0552-S-E
1.2
B781*8T
Iop
IR
Q
1.0
0.8
50
0.1 μH
1 μH
10 μH
100 μH
0.6
0.4
0.2
0 4
10
10 5
10 6
10 7
0
Hz 10 8
f
0
20
40
60
80
100
˚C
TA
7
06/12
140
Cautions and warnings
■ Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■ If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
Washing processes may damage the product due to the possible static or cyclic mechanical
loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,
which might lead to reduced reliability or lifetime.
■ The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■ Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Please read Cautions and warnings and
Important notes at the end of this document.
8
06/12
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of an electronic component could endanger human life or health (e.g.
in accident prevention or life-saving systems), it must therefore be ensured by means of suitable
design of the customer application or other action taken by the customer (e.g. installation of
protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available. The aforementioned does not apply in the case of individual agreements deviating
from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS,
DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,
MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap
are trademarks registered or pending in Europe and in other countries. Further information will
be found on the Internet at www.epcos.com/trademarks.
9
06/12
Similar pages