EPCOS B82422H1153000 Smt inductors simid series, simid 1210-h ferrite drum core Datasheet

SMT inductors
SIMID series, SIMID 1210-H
Series/Type:
B82422H
Date:
December 2012
a~í~=pÜÉÉí
¤EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures
hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
SMT inductors, SIMID series
B82422H
SIMID 1210-H
Size 1210 (EIA) or 3225 (IEC)
Rated inductance 0.1 ... 680 μH
Rated current 61 ... 2050 mA
Construction
■ Ferrite drum core
■ Laser-welded winding
■ Flame-retardant molding
Features
■
■
■
■
Temperature range up to +150 °C
Very high current handling capability
Qualified to AEC-Q200
Suitable for lead-free reflow soldering
as referenced in JEDEC J-STD 020D
■ RoHS-compatible
Applications
■
■
■
■
■
■
Filtering of supply voltages, coupling, decoupling
DC/DC converters, switch-mode power supplies
Automotive electronics (e.g. single wire bus systems)
Telecommunications
Consumer and data processing equipment
Industrial electronics
Terminals
■ Base material CuSn6
■ Layer composition Cu, Ag, Sn (lead-free)1)
■ Electro-plated
Marking
■ Marking on component:
Manufacturer and letter “H”, L value (in PH),
tolerance of L value (coded), date of manufacture (YWWD)
■ Minimum data on reel:
Manufacturer, ordering code, L value, quantity, date of packing
Delivery mode and packing units
■ 8-mm blister tape, wound on 180-mm or 330-mm ‡ reel
■ Packing units:
180-mm reel: 2000 pcs./reel
330-mm reel: 7500 pcs./reel
1) Ni-barrier-plated terminals on request (B82422H*50).
Please read Cautions and warnings and
Important notes at the end of this document.
2
12/12
SMT inductors, SIMID series
B82422H
SIMID 1210-H
Dimensional drawing and layout recommendation
1.9±0.1
1)
A
0.6±0.2 1)
B
C
D
B
IND0053-6
2.2±0.2
0.45 min.1)
3.2±0.2
0.15 max.
A
B
C
D
2.7
1.15
2.1
4.4
2.5±0.2
Marking
1) Soldering area
Dimensions in mm
IND0496-P-E
Taping and packing
Reel
<_ 2.8
4±0.1
_0
8.4 +1.5
1.0+0.2
_0
12.75 +0.15
_2
330 +0
8±0.3
2±0.05
_2
180 +0
1.5+0.1
<_ 4.2
Component
14.4 max.
3.5±0.05
4±0.1
1.75±0.1
Blister tape
62±1.5
IND0592-V
Direction of unreeling
IND0557-F-E
Dimensions in mm
Please read Cautions and warnings and
Important notes at the end of this document.
3
12/12
SMT inductors, SIMID series
B82422H
SIMID 1210-H
Technical data and measuring conditions
Rated inductance LR
Measured with impedance analyzer Agilent 4294A
at frequency fL, 0.1 V, +20 °C
Q factor Qmin
Measured with impedance analyzer Agilent 4294A
at frequency fQ, +20 °C
Rated temperature TR
+105 qC
Rated current IR
Maximum permissible DC with inductance decrease
'L/L0 d 10% and temperature increase
of d 45 K at rated temperature
Self-resonance frequency fres,min
Measured with impedance analyzer Agilent 4294A, +20 °C
DC resistance Rmax
Measured at +20 qC
Solderability (lead-free)
Sn95.5Ag3.8Cu0.7: +(245 r5) °C, (5 r0.3) s
Wetting of soldering area t 90%
(based on IEC 60068-2-58)
Resistance to soldering heat
+260 qC, 40 s (as referenced in JEDEC J-STD 020D)
Climatic category
55/150/56 (to IEC 60068-1)
Storage conditions
Mounted: –55°C … +150 °C
Packaged: –25 °C … +40 °C, d 75% RH
Weight
Approx. 50 mg
Please read Cautions and warnings and
Important notes at the end of this document.
4
12/12
SMT inductors, SIMID series
B82422H
SIMID 1210-H
Characteristics and ordering codes
Tolerance
LR
PH
fL
Qmin
MHz
1.0
r5%
1.5
r10%
IR
Rmax
fres,min
MHz
mA
:
MHz
Ordering code 1)2)
(‡ 180-mm reel)
7.96
10
2.52
1150
0.10
150
B82422H1102+000
7.96
10
2.52
900
0.14
110
B82422H1152+000
2.2
7.96
10
2.52
800
0.16
90
B82422H1222+000
3.3
7.96
10
2.52
770
0.18
70
B82422H1332+000
4.7
7.96
10
2.52
700
0.25
46
B82422H1472+000
6.8
7.96
10
2.52
570
0.35
35
B82422H1682+000
10
2.52
12
2.52
500
0.46
30
B82422H1103+000
15
2.52
12
2.52
390
0.72
26
B82422H1153+000
22
2.52
12
2.52
330
1.0
21
B82422H1223+000
33
2.52
15
2.52
280
1.4
15
B82422H1333+000
47
2.52
15
2.52
230
2.1
12
B82422H1473+000
68
2.52
15
2.52
180
3.4
10
B82422H1683+000
^
J
fQ
^
K
100
0.796 20
0.796
150
4.8
8.0 B82422H1104+000
150
0.796 20
0.796
120
7.5
6.0 B82422H1154+000
220
0.796 20
0.796
100
10.9
5.5 B82422H1224+000
330
0.796 20
0.796
90
13.0
4.5 B82422H1334+000
470
0.796 20
0.796
76
20.0
3.5 B82422H1474+000
680
0.796 20
0.796
61
31.0
3.0 B82422H1684+000
Intermediate values and closer tolerances on request.
Higher currents possible at temperatures <TR on request.
Sample kit available. Ordering code: B82422X002
For more information refer to chapter “Sample kits".
1) Replace the + by the code letter for the required inductance tolerance.
For reel size ‡ 330 mm the last digit has to be an »8«. Example: B82422H1102M008
2) For Ni-barrier-plated terminals replace the last two digits “00” by “50” (reel 180 mm) or “58” (reel 330 mm).
Please read Cautions and warnings and
Important notes at the end of this document.
5
12/12
SMT inductors, SIMID series
B82422H
SIMID 1210-H
Inductance L versus DC load current IDC
measured with LCR meter Agilent 4284A,
typical values at +20 °C
Impedance |Z| versus frequency f
measured with impedance analyzer Agilent
4294A/E4991A, typical values at +20 °C
IND0499-X
10 6
Ω B82422H
|Z|
IND0608-P
10 3
μH
B82422H
680 μH
L
10 5
100 μH
10 2
10 4
10 μH
10 1
10 3
1 μH
10 0
10 2
680 μH
100 μH
10 μH
1 μH
0.1 μH
10 1
10 0 6
10
10 7
10 8
10
10
Hz 10 9
f
_2
10
_2
10
_1
10 0
A 10 1
I DC
Current derating Iop/IR
versus ambient temperature TA
(rated temperature TR = +105 °C)
Q factor versus frequency f
measured with impedance analyzer
Agilent 4294A, typical values at +20 °C
IND0497-H
25
0.1 μH
_1
IND0498-R-E
1.2
B82422H
Iop
IR
Q
20
B82422H
1.0
0.8
15
0.6
680 μH
100 μH
10 μH
1 μH
0.1 μH
10
5
0 4
10
0.4
0.2
10 5
10 6
0
Hz 10 7
f
6
0
12/12
20
40
60
80 100 120
˚C 160
TA
Cautions and warnings
■ Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■ If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
Washing processes may damage the product due to the possible static or cyclic mechanical
loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,
which might lead to reduced reliability or lifetime.
■ The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■ Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Please read Cautions and warnings and
Important notes at the end of this document.
7
12/12
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of an electronic component could endanger human life or health (e.g.
in accident prevention or life-saving systems), it must therefore be ensured by means of suitable
design of the customer application or other action taken by the customer (e.g. installation of
protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available. The aforementioned does not apply in the case of individual agreements deviating
from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS,
DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,
MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap
are trademarks registered or pending in Europe and in other countries. Further information will
be found on the Internet at www.epcos.com/trademarks.
8
12/12
Similar pages