EPCOS B82462G4122M000

SMT power inductors
Size 6.3 × 6.3 × 3.0 (mm)
Series/Type:
B82462G4
Date:
March 2008
Data Sheet
 EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures
hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
SMT power inductors
B82462G4
Size 6.3 × 6.3 × 3.0 (mm)
Rated inductance 0.82 µH to 1000 µH
Rated current 0.16 A to 3.45 A
Construction
■
■
■
■
Ferrite core
Magnetically shielded
Winding: enamel copper wire
Winding welded to terminals
Features
■ Temperature range up to 150 °C
■ High rated current, low DC resistance
■ Suitable for lead-free reflow soldering
as referenced in JEDEC J-STD 020C
■ Qualified to AEC-Q200
■ RoHS-compatible
Applications
■
■
■
■
■
Filtering of supply voltages
Coupling, decoupling
DC/DC converters
Automotive electronics
Industrial electronics
Terminals
■ Base material CuSn6
■ Layer composition Ag, Sn (lead-free) 1)
■ Electro-plated
Marking
■ Marking on component:
Manufacturer, L value (nH, coded),
L tolerance (coded), manufacturing date (YWWD)
■ Minimum data on reel:
Manufacturer, ordering code,
L value, quantity, date of packing
Delivery mode and packing unit
■ 12-mm blister tape, wound on 330-mm ∅ reel
■ Packing unit: 2500 pcs./reel
1) Ni-barrier-plated terminals on request (B82462G4*050).
Please read Cautions and warnings and
Important notes at the end of this document.
2
03/08
SMT power inductors
B82462G4
Size 6.3 × 6.3 × 3.0 (mm)
2.4
1.5
1.5
7
IND0469-B
3 max.
0.15±0.03
0.45±0.11)
2±0.11)
Dimensional drawing and layout recommendation
0.9±0.11)
0.1
6±0.2
6.3 max.
Marking
6.3 max.
Dimensions in mm
1) Soldering area
IND0472-V-E
Taping and packing
Reel
_ 0.1
12 +0.3
2±0.05
_0
12.4 +1.5
1.6±0.1
3.45 max.
Direction of unreeling
IND0828-C-E
Dimensions in mm
3
62±1.5
IND0350-S
8±0.1
Please read Cautions and warnings and
Important notes at the end of this document.
13±0.2
_2
330 +0
1.5+0.1
7.5 max.
Component
18.4 max.
5.5±0.05
4±0.1
1.75±0.1
Blister tape
03/08
SMT power inductors
B82462G4
Size 6.3 × 6.3 × 3.0 (mm)
Technical data and measuring conditions
Rated inductance LR
Measured with impedance analyzer Agilent 4294A at
frequency fL, 0.1 V, 20 °C
Rated temperature TR
85 °C
Rated current IR
Max. permissible DC with temperature increase of ≤ 40 K
at rated temperature
Saturation current Isat
Max. permissible DC with inductance decrease
∆L/L0 of approx. 10%
DC resistance Rmax
Measured at 20 °C
Solderability (lead-free)
Dip and look method Sn95.5Ag3.8Cu0.7:
(245 ±5) °C, (5 ±0.3) s
Wetting of soldering area ≥ 90%
(based on IEC 60068-2-58)
Resistance to soldering heat
260 °C, 40 s as referenced in JEDEC J-STD 020C
Climatic category
55/150/56 (to IEC 60068-1)
Storage conditions
Mounted: –55 °C … +150 °C
Packaged: –25 °C … +40 °C, ≤ 75% RH
Weight
Approx. 1.5 g
Please read Cautions and warnings and
Important notes at the end of this document.
4
03/08
SMT power inductors
B82462G4
Size 6.3 × 6.3 × 3.0 (mm)
Characteristics and ordering codes
LR
Tolerance fL
IR
Isat
Rmax
A
A
Ω
M 0.1
3.45
4.45
0.015
B82462G4821M000
1.0
0.1
3.40
4.40
0.016
B82462G4102M000
1.2
0.1
3.25
3.90
0.017
B82462G4122M000
1.5
0.1
3.10
3.60
0.020
B82462G4152M000
2.2
0.1
2.55
2.60
0.025
B82462G4222M000
3.3
0.1
2.30
2.10
0.031
B82462G4332M000
4.7
0.1
2.00
1.80
0.040
B82462G4472M000
6.8
0.1
1.65
1.50
0.050
B82462G4682M000
10
0.1
1.50
1.30
0.062
B82462G4103M000
15
0.1
1.25
1.05
0.097
B82462G4153M000
22
0.1
1.05
0.85
0.15
B82462G4223M000
33
0.1
0.85
0.72
0.23
B82462G4333M000
47
0.1
0.75
0.60
0.31
B82462G4473M000
68
0.1
0.65
0.50
0.41
B82462G4683M000
100
0.1
0.53
0.42
0.58
B82462G4104M000
150
0.1
0.38
0.33
1.05
B82462G4154M000
220
0.1
0.35
0.28
1.35
B82462G4224M000
330
0.1
0.27
0.22
2.30
B82462G4334M000
470
0.1
0.24
0.18
2.70
B82462G4474M000
680
0.1
0.20
0.15
4.05
B82462G4684M000
1000
0.1
0.16
0.13
6.00
B82462G4105M000
µH
MHz
0.82
±20%
^
Sample kit available. Ordering code: B82462X004
For more information refer to chapter “Sample kits”.
1) For Ni-barrier-plated terminals replace the last two digits “00” by “50”.
Please read Cautions and warnings and
Important notes at the end of this document.
5
03/08
Ordering code
SMT power inductors
B82462G4
Size 6.3 × 6.3 × 3.0 (mm)
Impedance |Z| versus frequency f
measured with impedance analyzer
Agilent 4294A, typical values at 20 °C
Inductance L versus DC load current IDC
measured with LCR meter Agilent 4275A,
typical values at 20 °C
IND0501-T
10 6
Ω B82462G4
5
|Z| 10
10
IND0502-U
10 4
µH B82462G4
L
1000 µH
10 3
4
10 3
10 2
100 µH
10 1
10 µH
10 2
10 1
1000 µH
100 µH
10 µH
1 µH
10 0
10
10
_1
_2
10
3
10
4
10
5
10
6
7
10 Hz 10
f
1 µH
10 0
10
8
_1
10
_2
I op
IR
IND0602-K
1.0
0.8
0.6
0.4
0.2
0
0
20
40
60
80
_1
10 0
A 10 1
I DC
Current derating Iop/IR
versus ambient temperature TA
(rated temperature TR = 85 °C)
1.2
10
100 120 ˚C 150
TA
6
03/08
Cautions and warnings
■ Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■ If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
■ The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■ Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Please read Cautions and warnings and
Important notes at the end of this document.
7
03/08
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with
them than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very
high level of operational safety and especially in customer applications in which the malfunction
or failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of
the customer application or other action taken by the customer (e.g. installation of protective
circuitry or redundancy) that no injury or damage is sustained by third parties in the event of
malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available.
The aforementioned does not apply in the case of individual agreements deviating from the
foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP, MiniBlue,
MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are
trademarks registered or pending in Europe and in other countries. Further information will be
found on the Internet at www.epcos.com/trademarks.
8
03/09