EPCOS B82801C1265A150

Inductors
SMT current sense transformers, EE 12.6
Series/Type:
Ordering code:
B82801C
Date:
Version:
2009-08-14
1
Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the
table and then change the color to "white". This ensures that the table disappears (invisible) for the customer PDF.
Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it!
Identification/Classification 1
(header 1 + top left bar):
Inductors
Identification/Classification 2
(header 2 + bottom left header bar):
SMT current sense transformers, EE 12.6
Ordering code: (top right header bar)
Series/Type: (top right header bar)
B82801C
Preliminary data (optional):
(if necessary)
Department:
EPCOS HO PD
Date:
2009-08-14
Version:
1
 EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information
contained therein without EPCOS' prior express consent is prohibited
Inductors
SMT current sense transformers, EE 12.6
B82801C
Applications
 Switching power supplies
 Sensing and monitoring continuous currents
to <40 A in analog systems
 Frequency range: 50 kHz … 500 kHz
Features
 Very low DC resistance
 Different turns ratios
 RoHS-compatible
Marking
 Four digits from the middle block of ordering code
Delivery mode and packing unit
 32-mm blister tape, 330-mm Ø reel
 Carton packaging
 Packing units:
200 pcs./reel, 800 pcs./carton
EPCOS HO PD
Please read Cautions and warnings and
Important notes at the end of this document.
2009-08-14
Page 2 of 8
Inductors
SMT current sense transformers, EE 12.6
B82801C
Dimensional drawing and pin configuration
EPCOS HO PD
Please read Cautions and warnings and
Important notes at the end of this document.
2009-08-14
Page 3 of 8
Inductors
SMT current sense transformers, EE 12.6
B82801C
Application circuit
Taping and packing
Blister tape
Reel
29.2 max.
_0
12.75 +0.15
ø62±1.5
_0
24.4 +2
_2
330 +0
IND0660-Z
EPCOS HO PD
Please read Cautions and warnings and
Important notes at the end of this document.
2009-08-14
Page 4 of 8
Inductors
SMT current sense transformers, EE 12.6
B82801C
Technical data and measuring conditions
Frequency range
50 kHz … 500 kHz
Sensed current
The max. primary current of 40 A causes approx. 40 °C
temperature rise.
Test voltage Vtest
50 Hz, 1 s (winding/winding)
Rated temperature
Approx. 40 °C
Inductance L (24)
100 kHz, 1.0 V, 25 °C
DC resistance Rmax
Measured at 25 °C
Solderability
≥99.9 Sn lead-free
or Sn96.5Ag3.0Cu0.5: (245 5) °C, (3 0.3) s
Wetting of soldering area: ≥95%
(to IEC 60068-2-58)
Resistance to soldering heat
(reflow soldering)
Reflow process at 245 5 °C (to JEDEC J-STD 020C)
Storage conditions
20 °C … +40 °C, ≤ 75 %
Operating temperature range
40 °C … +130 °C
Weight
Approx. 4.8 g
Characteristics and ordering codes
Ordering code
Lmin
Turns ratio DC resistance Rmax (m)
Sensed current
Vtest
mH
Np : Ns
primary
A
V AC
1.4
1 : 50
0.28
400
40
1500
B82801C0145A050
5.6
1 : 100
0.28
1000
40
1500
B82801C0565A100
12.6
1 : 150
0.28
2200
40
1500
B82801C1265A150
22.4
1 : 200
0.28
2900
40
1500
B82801C2245A200
secondary
EPCOS HO PD
Please read Cautions and warnings and
Important notes at the end of this document.
2009-08-14
Page 5 of 8
Inductors
SMT current sense transformers, EE 12.6
B82801C
Recommended reflow soldering curve
Pb-free solder material (based on JEDEC J-STD 020C)
t3
T4
T3
t2
T2
T1
t1
IND0814-F
Classification of reflow soldering process
T1
°C
T2
°C
T3
°C
T4
°C
t1
s
t2
s
t3
s
150
200
217
245
<110
<90
T4 5 °C
EPCOS HO PD
Please read Cautions and warnings and
Important notes at the end of this document.
2009-08-14
Page 6 of 8
Inductors
SMT current sense transformers, EE 12.6
B82801C
Cautions and warnings
 Please note the recommendations in our Inductors data book (latest edition or in the Internet) and
in the data sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■ If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative
effect in the long-term on wire insulation.
 The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire insulation,
plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
 Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
 Even for customer-specific products, conclusive validation of the component in the circuit can only
be carried out by the customer.
EPCOS HO PD
Please read Cautions and warnings and
Important notes at the end of this document.
2009-08-14
Page 7 of 8
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As a
rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very high
level of operational safety and especially in customer applications in which the malfunction or
failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of the
customer application or other action taken by the customer (e.g. installation of protective circuitry
or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or
failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material
Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed
questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available.
The aforementioned does not apply in the case of individual agreements deviating from the
foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of
the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP, MiniBlue,
MiniCell, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT,
SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse,
WindCap are trademarks registered or pending in Europe and in other countries. Further
information will be found on the Internet at www.epcos.com/trademarks.
Page 8 of 8