Rohm BA3474YFVMTR Automotive high speed operational amplifier Datasheet

Datasheet
Operational Amplifiers Series
Automotive High Speed
Operational Amplifiers
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
●General Description
BA3472Y, BA3474Y, BA3472W, and BA3474W
integrate two or four independent Op-amps on a
single chip. These Op-Amps can operate from
+3V to +36V (single power supply) with a high
slew rate (10V/μs) and high-gain bandwidth
(4MHz) characteristics.
●Key Specifications
 Wide Operating Supply Voltage:
Single supply
+3.0V to +36.0V
Dual supply
±1.5V to ±18.0V
 Wide Temperature Range:
-40°C to +125°C
 Input Offset Voltage:
BA3472Y, BA3474Y
10mV (Max.)
BA3472W, BA3474W
7.5mV (Max.)
 Low Input Offset Current:
6nA (Typ.)
 Low Input Bias Current:
100nA (Typ.)
 Wide Output Voltage Range:
VEE+0.3V to VCC-1.0V(Typ.)
(VCC-VEE=30V)
 High Slew Rate:
10V/µs(Typ.)
 Gain Band Width:
4MHz(Typ.)
●Features
 Single or dual power supply operation
 Wide operating supply voltage
 Standard Op-Amp Pin-assignments
 High open-loop voltage gain
 Internal ESD protection circuit
 Common-mode Input Voltage Range includes
ground level, allowing direct ground sensing
 Wide output voltage range
 AEC-Q100 Qualified
●Packages
SOP8
SSOP-B8
MSOP8
SSOP-B14
●Application
 Engine Control Unit
 Electric Power Steering (EPS)
 Anti-Lock Braking System (ABS)
 All automotive application
W(Typ.) x D(Typ.) x H(Max.)
5.00mm x 6.20mm x 1.71mm
3.00mm x 6.40mm x 1.35mm
2.90mm x 4.00mm x 0.90mm
5.00mm x 6.40mm x 1.35mm
●Simplified schematic
VCC
VCC
-IN VIN-
VOUT
OUT
+IN
VIN+
VEE
VEE
Figure 1. Simplified schematic (one channel only)
○Product structure:Silicon monolithic integrated circuit
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・00
○This product is not designed protection against radioactive rays.
1/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
●Pin Configuration(TOP VIEW)
SOP8, SSOP-B8, MSOP8
Pin No.
Symbol
1
OUT1
2
-IN1
3
+IN1
4
VEE
5
+IN2
6
-IN2
7
OUT2
8
VCC
Pin No.
Symbol
1
OUT1
14 OUT4
2
-IN1
13 -IN4
3
+IN1
+IN1 3
12 +IN4
4
VCC
VCC 4
11 VEE
5
+IN2
10 +IN3
6
-IN2
9 -IN3
7
OUT2
8 OUT3
8
OUT3
9
-IN3
10
+IN3
11
VEE
12
+IN4
13
-IN4
14
OUT4
OUT1 1
-IN1
2
+IN1
3
VEE
8 VCC
7 OUT2
CH1
- +
6 -IN2
CH2
+ -
4
5 +IN2
SSOP-B14
OUT1 1
-IN1 2
+IN2
CH1
- +
CH4
+ -
5
-IN2 6
- +
CH2
+ CH3
OUT2 7
Package
SOP8
BA3472YF-C
SSOP-B8
MSOP8
SSOP-B14
BA3472YFV-C
BA3472WFV-C
BA3472YFVM-C
BA3474YFV-C
BA3474WFV-C
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
2/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
●Ordering Information
B
A
3
4
7
x
x
x
x
x
-
Package
F
: SOP8
FV : SSOP-B8
SSOP-B14
FVM : MSOP8
Part Number
BA3472Y
BA3472W
BA3474Y
BA3474W
C
xx
C: Automotive(Engine control unit、EPS、
ABS, and so on)
Packaging and forming specification
E2: Embossed tape and reel
(SOP8/SSOP-B8/SSOP-B14)
TR: Embossed tape and reel
(MSOP8)
●Line-up
Topr
-40°C to +125°C
Package
SOP8
Reel of 2500
BA3472YF-CE2
SSOP-B8
Reel of 2500
BA3472YFV-CE2
MSOP8
Reel of 3000
BA3472YFVM-CTR
SSOP-B8
Reel of 2500
BA3472WFV-CE2
SSOP-B14
Reel of 2500
BA3474YFV-CE2
SSOP-B14
Reel of 2500
BA3474WFV-CE2
●Absolute Maximum Ratings (Ta=25℃)
○BA3472Y, BA3472W, BA3474Y, BA3474W
Parameter
Symbol
Supply Voltage
Power dissipation
Differential Input Voltage*6
Orderable
Part Number
VCC-VEE
Ratings
Unit
+36
V
SOP8
1075*1*5
SSOP-B8
835*1*3
MSOP8
750*3*5
SSOP-B14
1350*2*3
Pd
mW
Vid
+36
V
Input Common-mode Voltage Range
Vicm
V
Operating Supply Voltage
Vopr
Operating Temperature
Topr
(VEE-0.3) to VEE+36
+3.0Vto+36.0V
(±1.5Vto±18.0V)
-40 to +125
℃
Tstg
-55 to +150
℃
Tjmax
+150
℃
Storage Temperature
Maximum Junction Temperature
V
Note Absolute maximum rating item indicates the condition which must not be exceeded.
Application of voltage in excess of absolute maximum rating or use out absolute maximum rated temperature environment may cause
deterioration of characteristics.
*1
To use at temperature above Ta=25℃ reduce 8.6mW/℃.
*2
To use at temperature above Ta=25℃ reduce 6.7mW/℃.
*3
To use at temperature above Ta=25℃ reduce 6.0mW/℃.
*4
To use at temperature above Ta=25℃ reduce 10.8mW/℃.
*5
Mounted on a FR4 glass epoxy 4 layers PCB 70mm×70mm×1.6mm (occupied copper area: 70mm×70mm).
*6
The voltage difference between inverting input and non-inverting input is the differential input voltage.
Then input terminal voltage is set to more than VEE.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
3/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
●Electrical Characteristics
○BA3472Y (Unless otherwise specified VCC=+15V, VEE=-15V)
Limits
Temperature
Parameter
Symbol
range
Min.
Typ.
Input Offset Voltage *7
Vio
Input Offset Current *7
*7
*8
*9
nA
Vicm=0V, OUT=0V
mA
RL=∞
6
75
full range
-
-
100
25℃
-
100
150
full range
-
-
200
25℃
-
4
5
full range
-
-
5.5
25℃
3.7
4
-
full range
3.5
-
-
25℃
13.7
14
-
full range
13.5
-
-
25℃
13.5
-
-
RL=2kΩ
25℃
-
0.1
0.3
full range
-
-
0.6
VCC=5V
VEE=0V
25℃
-
-14.7
-14.3
full range
-
-
-14.0
25℃
-
-
-13.5
25℃
80
100
-
full range
70
-
-
25℃
0
-
VCC-2.0
full range
0
-
VCC-2.6
CMRR
25℃
60
97
PSRR
25℃
60
25℃
VCC=5V
VEE=0V
RL=2kΩ
V
RL=2kΩ
V
RL=10kΩ
Av
*9
RL≧2kΩ, OUT=±10V
V
VCC=5V
VEE=0V
-
dB
OUT=0V
97
-
dB
Vicm=0V, OUT=0V
10
30
mA
full range
10
-
-
VCC=5V
VEE=0V
25℃
20
30
mA
VCC=5V
VEE=0V
Isource
Isink
GBW
full range
20
-
-
25℃
-
4
-
25℃
-
10
-
full range
5
-
-
25℃
-
120
-
SR
CS
RL=2kΩ
dB
Vicm
Common-mode Rejection
Ratio
Power Supply Rejection
Ratio
Channel Separation
Vicm=0V, OUT=0V
-
VOL
Input Common-mode
Voltage Range
Slew Rate
nA
25℃
Vicm=0V
OUT=VCC/2
RL=10kΩ
Large Signal Voltage Gain
Gain Band Width
VCC=5V
VEE=0V
10
VOH
Maximum Output
Voltage(Low)
Output Sink Current *9
Vicm=0V, OUT=0V
mV
-
ICC
Maximum Output
Voltage(High)
Condition
-
Ib
Supply Current
Unit
10
full range
Iio
Input Bias Current *8
Output Source Current
-
Max.
Datasheet
MHz
V/μs
OUT=VCC/2
IN+=1V
IN-=0V
OUT=0V
Only 1ch is short circuit
IN+=0V
IN-=1V
OUT=5V,
Only 1ch is short circuit
-
Av=1, IN=-10V to +10V,
RL=2kΩ
dB
-
Absolute value
Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.
Under high temperatures, please consider the power dissipation when selecting the output current.
When the output terminal is continuously shorted the output current reduces the internal temperature by flushing.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
4/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
●Electrical Characteristics
○BA3472W (Unless otherwise specified VCC=+15V, VEE=-15V)
Limits
Temperature
Parameter
Symbol
range
Min.
Typ.
Input Offset Voltage *10
Vio
Input Offset Current *10
-
Max.
-
-
7.5
25℃
-
6
75
full range
-
-
100
25℃
-
100
150
full range
-
-
200
25℃
-
4
5
full range
-
-
5.5
25℃
3.7
4
-
full range
3.5
-
-
25℃
13.7
14
-
full range
13.5
-
-
25℃
13.5
-
-
25℃
-
0.1
0.3
-
-
0.6
-
-
0.3
Iio
Input Bias Current *11
Ib
Supply Current
ICC
Maximum Output
Voltage(High)
VOH
Unit
7.5
full range
Datasheet
Condition
Vicm=0V, OUT=0V
mV
VCC=5V
VEE=0V
nA
Vicm=0V, OUT=0V
nA
Vicm=0V, OUT=0V
mA
RL=∞
VCC=5V
VEE=0V
Vicm=0V
OUT=VCC/2
RL=2kΩ
V
RL=10kΩ
RL=2kΩ
VCC=5V
VEE=0V
full range
Maximum Output
Voltage(Low)
VOL
RL=2kΩ
Isink=1mA
V
25℃
-
-14.7
-14.3
full range
-
-
-14.0
25℃
-
-
-13.5
25℃
80
100
-
full range
70
-
-
25℃
0
-
VCC-2.0
full range
0
-
VCC-2.6
CMRR
25℃
60
97
PSRR
25℃
60
25℃
RL=10kΩ
Large Signal Voltage Gain
Input Common-mode
Voltage Range
Output Sink Current *12
Gain Band Width
Slew Rate
Channel Separation
*10
*11
*12
dB
RL≧2kΩ, OUT=±10V
V
VCC=5V
VEE=0V
-
dB
OUT=0V
97
-
dB
Vicm=0V, OUT=0V
10
30
mA
full range
10
-
-
VCC=5V
VEE=0V
25℃
20
30
mA
full range
20
-
-
VCC=5V
VEE=0V
25℃
-
4
-
25℃
-
10
-
full range
5
-
-
25℃
-
120
-
Vicm
Common-mode Rejection
Ratio
Power Supply Rejection
Ratio
Output Source Current
Av
*12
Isource
Isink
GBW
SR
CS
RL=2kΩ
MHz
V/μs
OUT=VCC/2
IN+=1V
IN-=0V
OUT=0V
Only 1ch is short circuit
IN+=0V
IN-=1V
OUT=5V
Only 1ch is short circuit
-
Av=1, IN=-10V to +10V
RL=2kΩ
dB
-
Absolute value
Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.
Under high temperatures, please consider the power dissipation when selecting the output current.
When the output terminal is continuously shorted the output current reduces the internal temperature by flushing.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
5/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
●Electrical Characteristics
○BA3474Y (Unless otherwise specified VCC=+15V, VEE=-15V)
Limits
Temperature
Parameter
Symbol
range
Min.
Typ.
-
Input Offset Voltage *13
Vio
Input Offset Current *13
-
Max.
Vicm=0V, OUT=0V
mV
VCC=5V
VEE=0V
nA
Vicm=0V, OUT=0V
nA
Vicm=0V, OUT=0V
-
10
25℃
-
6
75
full range
-
-
100
25℃
-
100
150
full range
-
-
200
25℃
-
8
10
-
-
9
-
-
11
25℃
3.7
4
-
full range
3.5
-
-
25℃
13.7
14
-
full range
13.5
-
-
25℃
13.5
-
-
RL=2kΩ
25℃
-
0.1
0.3
full range
-
-
0.6
VCC=5V
VEE=0V
25℃
-
-14.7
-14.3
full range
-
-
-14.0
25℃
-
-
-13.5
25℃
80
100
-
full range
70
-
-
25℃
0
-
VCC-2.0
Ib
Supply Current
Condition
Iio
Input Bias Current *14
Unit
10
full range
Datasheet
ICC
Vicm=0V
OUT=VCC/2
RL=∞
mA
VCC=15V, RL=∞
full range
Maximum Output
Voltage(High)
VOH
VOL
Input Common-mode
Voltage Range
Slew Rate
Channel Separation
*13
*14
*15
Av
Vicm
Common-mode Rejection
Ratio
Power Supply Rejection
Ratio
Gain Band Width
RL=2kΩ
V
RL=2kΩ
V
RL=10kΩ
Large Signal Voltage Gain
Output Sink Current *15
VCC=5V
VEE=0V
RL=10kΩ
Maximum Output
Voltage(Low)
Output Source Current
RL=∞
*15
RL=2kΩ
dB
RL≧2kΩ, OUT=±10V
V
VCC=5V
VEE=0V
OUT=VCC/2
full range
0
-
VCC-2.6
CMRR
25℃
60
97
-
dB
OUT=0V
PSRR
25℃
60
97
-
dB
Vicm=0V, OUT=0V
25℃
10
30
mA
full range
10
-
-
VCC=5V
VEE=0V
25℃
20
30
mA
VCC=5V
VEE=0V
Isource
Isink
GBW
full range
20
-
-
25℃
-
4
-
25℃
-
10
-
SR
CS
MHz
V/μs
full range
5
-
-
25℃
-
120
-
IN+=1V
IN-=0V
OUT=0V
Only 1ch is short circuit
IN+=0V
IN-=1V
OUT=5V
Only 1ch is short circuit
-
Av=1, IN=-10V to +10V
RL=2kΩ
dB
-
Absolute value
Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.
Under high temperatures, please consider the power dissipation when selecting the output current.
When the output terminal is continuously shorted the output current reduces the internal temperature by flushing.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
6/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
●Electrical Characteristics
○BA3474W (Unless otherwise specified VCC=+15V, VEE=-15V)
Limits
Temperature
Parameter
Symbol
range
Min.
Typ.
-
Input Offset Voltage *16
Vio
Input Offset Current *16
-
Max.
-
-
7.5
25℃
-
6
75
full range
-
-
100
25℃
-
100
150
full range
-
-
200
25℃
-
8
10
-
-
9
-
-
11
25℃
3.7
4
-
full range
3.5
-
-
25℃
13.7
14
-
full range
13.5
-
-
25℃
13.5
-
-
25℃
-
0.1
0.3
-
-
0.6
-
-
0.3
Iio
Input Bias Current *17
Ib
Supply Current
ICC
Unit
7.5
full range
Datasheet
Condition
Vicm=0V, OUT=0V
mV
VCC=5V
VEE=0V
nA
Vicm=0V, OUT=0V
nA
Vicm=0V, OUT=0V
Vicm=0V
OUT=VCC/2
RL=∞
mA
VCC=15V, RL=∞
full range
Maximum Output
Voltage(High)
VOH
RL=∞
VCC=5V
VEE=0V
RL=2kΩ
V
RL=10kΩ
RL=2kΩ
VCC=5V
VEE=0V
full range
Maximum Output
Voltage(Low)
VOL
RL=2kΩ
I sink=1mA
V
25℃
-
-14.7
-14.3
full range
-
-
-14.0
25℃
-
-
-13.5
25℃
80
100
-
full range
70
-
-
25℃
0
-
VCC-2.0
full range
0
-
VCC-2.6
CMRR
25℃
60
97
PSRR
25℃
60
25℃
10
RL=10kΩ
Large Signal Voltage Gain
Input Common-mode
Voltage Range
Output Sink Current *18
Gain Band Width
Slew Rate
Channel Separation
*16
*17
*18
dB
RL≧2kΩ, OUT=±10V
V
VCC=5V
VEE=0V
-
dB
OUT=0V
97
-
dB
Vicm=0V, OUT=0V
30
mA
VCC=5V
VEE=0V
mA
VCC=5V
VEE=0V
Vicm
Common-mode Rejection
Ratio
Power Supply Rejection
Ratio
Output Source Current
Av
*18
Isource
full range
10
-
-
25℃
20
30
-
Isink
GBW
full range
20
-
-
25℃
-
4
-
25℃
-
10
-
full range
5
-
-
25℃
-
120
-
SR
CS
RL=2kΩ
MHz
V/μs
OUT=VCC/2
IN+=1V
IN-=0V
OUT=0V
Only 1ch is short circuit
IN+=0V
IN-=1V
OUT=5V
Only 1ch is short circuit
-
Av=1, IN=-10V to +10V
RL=2kΩ
dB
-
Absolute value
Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.
Under high temperatures, please consider the power dissipation when selecting the output current.
When the output terminal is continuously shorted the output current reduces the internal temperature by flushing.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
7/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
Description of Electrical Characteristics
Described below are descriptions of the relevant electrical terms used in this datasheet. Items and symbols used are also
shown. Note that item name and symbol and their meaning may differ from those on another manufacturer’s document or
general document.
1. Absolute maximum ratings
Absolute maximum rating items indicate the condition which must not be exceeded. Application of voltage in excess of absolute
maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics.
1.1 Power supply voltage (VCC-VEE)
Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power
supply terminal without deterioration or destruction of characteristics of internal circuit.
1.2 Differential input voltage (Vid)
Indicates the maximum voltage that can be applied between non-inverting and inverting terminals without damaging
the IC.
1.3 Input common-mode voltage range (Vicm)
Indicates the maximum voltage that can be applied to the non-inverting and inverting terminals without deterioration
or destruction of electrical characteristics. Input common-mode voltage range of the maximum ratings does not assure
normal operation of IC. For normal operation, use the IC within the input common-mode voltage range characteristics.
1.4 Power dissipation (Pd)
Indicates the power that can be consumed by the IC when mounted on a specific board at the ambient temperature 25℃
(normal temperature). As for package product, Pd is determined by the temperature that can be permitted by the IC in
the package (maximum junction temperature) and the thermal resistance of the package.
2. Electrical characteristics
2.1 Input offset voltage (Vio)
Indicates the voltage difference between non-inverting terminal and inverting terminals. It can be translated into the
input voltage difference required for setting the output voltage at 0 V.
2.2 Input offset current (Iio)
Indicates the difference of input bias current between the non-inverting and inverting terminals.
2.3 Input bias current (Ib)
Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias currents at
the non-inverting and inverting terminals.
2.4 Circuit current (ICC)
Indicates the current that flows within the IC under specified no-load conditions.
2.5 High level output voltage/low level output voltage (VOH/VOL)
Indicates the voltage range of the output under specified load condition. It is typically divided into high-level output
voltage and low-level output voltage. High-level output voltage indicates the upper limit of output voltage while
Low-level output voltage indicates the lower limit.
2.6 Large signal voltage gain (Av)
Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal
and inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage.
Av = (Output voltage fluctuation) / (Input offset fluctuation)
2.7 Input common-mode voltage range (Vicm)
Indicates the input voltage range where IC normally operates.
2.8 Common-mode rejection ratio (CMRR)
Indicates the ratio of fluctuation of input offset voltage when the input common mode voltage is changed. It is
normally the fluctuation of DC.
CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation)
2.9 Power supply rejection ratio (PSRR)
Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. It is normally the fluctuation of
DC.
PSRR= (Change of power supply voltage)/(Input offset fluctuation)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
8/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
2.10 Output source current/ output sink current (IOH / IOL)
The maximum current that can be output from the IC under specific output conditions. The output source current
indicates the current flowing out from the IC, and the output sink current indicates the current flowing into the IC.
2.11 Gain Band Width (GBW)
The product of the open-loop voltage gain and the frequency at which the voltage gain decreases 6dB/octave.
2.12 Slew rate (SR)
Indicates the ratio of the change in output voltage with time when a step input signal is applied.
2.13 Channel separation (CS)
Indicates the fluctuation in the output voltage of the driven channel with reference to the change of output voltage of
the channel which is not driven.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
9/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
●Typical Performance Curves
○BA3472Y, BA3472W
1200
6
SUPPLY CURRENT [mA]
POWER DISSIPATION [mW]
1000
BA3472YF-C
800
BA3472YFV-C
BA3472WFV-C
600
BA3472YFVM-C
400
200
0
5
-40℃
25℃
4
125℃
3
2
1
0
0
25
50
75
100
125
0
150
5
15
20
25
30
35
40
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Figure 2.
Derating Curve
Figure 3.
Supply Current - Supply Voltage
40
6
35
5
30V
OUTPUT VOLTAGE[V]
SUPPLY CURRENT [mA]
10
36V
4
3
3V
5V
2
1
30
-40℃
25
25℃
20
15
125℃
10
5
0
0
-50 -25
0
25
50
75
0
100 125 150
AMBIENT TEMPERATURE [℃]
10
20
30
40
SUPPLY VOLTAGE[V]
Figure 4.
Supply Current - Ambient Temperature
Figure 5.
Maximum Output Voltage(High)
- Supply Voltage
(RL=10kΩ)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
10/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3472Y, BA3472W
1. 0
40
OUTPUT VOLTAGE[V]
OUTPUT VOLTAGE[V]
35
30
36V
25
30V
20
15
10
5V
0. 8
0. 6
0. 4
125℃
25℃
-40℃
0. 2
3V
5
0. 0
0
-50 -25
0
25
50
75
0
100 125 150
AMBIENT TEMPERATURE [℃]
20
30
40
SUPPLY VOLTAGE[V]
Figure 6.
Figure 7.
Maximum Output Voltage(High)
Maximum Output Voltage(Low)
- Ambient Temperature
(RL=10kΩ)
- Supply Voltage
(RL=10kΩ)
100. 0
OUTPUT SOURCE CURRENT[mA]
1. 0
0. 8
OUTPUT VOLTAGE[V]
10
0. 6
0. 4
5V
36V
3V
30V
0. 2
0. 0
-50
-25
0
25
50
75
100 125 150
10.0
125℃
25℃
1. 0
-40℃
0. 1
0
1
2
3
4
5
AMBIENT TEMPERATURE [℃]
VCC-OUT[V]
Figure 8.
Figure 9.
Output Source Current - (VCC-OUT)
(VCC/VEE=5V/0V)
Maximum Output Voltage(Low)
- Ambient Temperature
(RL=10kΩ)
6
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
11/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3472Y, BA3472W
5
INPUT OFFSET VOLTAGE[mV]
-40℃
25℃
125℃
10.0
1. 0
4
3
2
-40℃
25℃
1
0
-1
125℃
-2
-3
-4
-5
0. 1
0
1
2
3
4
5
-20
6
OUT-VEE[V]
-15
-10
-5
0
5
10
15
COMMON MODE INPUT VOLTAGE[V]
Figure 10.
Output Source Current - (OUT-VEE)
(VCC/VEE=5V/0V)
Figure 11.
Input Offset Voltage
- Common Model Input Voltage
(VCC/VEE=15V/-15V)
3
3
INPUT OFFSET VOLTAGE[mV]
INPUT OFFSET VOLTAGE[mV]
OUTPUT SINK CURRENT[mA]
100. 0
2
-40℃
25℃
1
0
125℃
-1
-2
-3
2
30V
36V
1
5V
0
-1
-2
-3
0
5
10
15
20
25
30
35
40
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE[℃]
SUPPLY VOLTAGE[V]
Figure 12.
Input Offset Voltage - Supply voltage
Figure 13.
Input Offset Voltage - Ambient Temperature
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
12/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3472Y, BA3472W
100
100
25℃
-40℃
80
INPUT BIAS CURRENT[nA]
INPUT BIAS CURRENT[nA]
36V
60
125℃
40
20
30V
80
60
5V
40
3V
20
0
0
0
5
10
15
20
25
30
35
-50
40
SUPPLY VOLTAGE[V]
0
25
50
75
100 125 150
AMBIENT TEMPERATURE[℃]
Figure 14.
Input Bias Current - Supply Voltage
Figure 15.
Input Bias Current - Ambient Temperature
150
LARGE SIGNAL VOLTAGE GAIN[dB]
150
LARGE SIGNAL VOLTAGE GAIN[dB]
-25
140
130
-40℃
25℃
120
110
125℃
100
90
80
70
60
50
140
130
10V
30V
120
110
36V
100
90
80
70
60
50
5
10
15
20
25
30
35
40
-50
SUPPLY VOLTAGE[V]
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE[℃]
Figure 16.
Large Signal Voltage Gain
- Supply Voltage
Figure 17.
Large Signal Voltage Gain
- Ambient Temperature
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
13/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3472Y, BA3472W
140
150
130
140
120
130
120
110
110
CMRR[dB]
CMRR[dB]
125℃
100
90
25℃
80
-40℃
90
80
70
70
60
60
50
50
40
40
0
5
10
15
20
25
30
35
5V
-50
40
SUPPLY VOLTAGE[V]
14
14
SLEW RATE(RISE)[V/μs]
SLEW RATE(RISE)[V/μs]
16
-40℃
25℃
8
125℃
6
0
25
50
75
100 125 150
Figure 19.
Common Mode Rejection Ratio
- Ambient Temperature
16
10
-25
AMBIENT TEMPERATURE[℃]
Figure 18.
Common Mode Rejection Ratio
- Supply Voltage
12
36V
30V
100
4
36V
30V
12
10
2
8
15V
6
5V
4
3V
2
0
0
0
5
10
15
20
25
30
35
40
-50
SUPPLY VOLTAGE[V]
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE[℃]
Figure 20.
Slew Rate L-H - Supply Voltage
(RL=10kΩ)
Figure 21.
Slew Rate L-H Ambient Temperature
(RL=10kΩ)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
14/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3472Y, BA3472W
50
0
12
GAIN
30
-60
20
-90
10
-120
0
PHASE[deg]
VOLTAGE GAIN[dB]
-30
-150
INPUT/OUTPUT VOLTAGE[V]
10
PHASE
40
8
6
OUTPUT
4
INPUT
2
0
-2
-4
-6
-8
-10
-10
1
10
100
1000
-180
10000
-12
0
FREQUENCY[kHz]
1
2
3
4
5
6
7
TIME[μs]
Figure 22.
Voltage Gain・Phase - Frequency
(VCC/VEE=+15V/-15V, Av=40dB
RL=2kΩ, CL=100pF, Ta=25℃)
Figure 23.
Input / Output Voltage - Time
(VCC/VEE=+15V/-15V, Av=0dB,
RL=2kΩ, CL=100pF, Ta=25℃)
INPUT/OUTPUT VOLTAGE[mV]
100
80
INPUT
60
40
OUTPUT
20
0
-20
-40
-60
-80
-100
0.0
0.5
1.0
1.5
2.0
2.5
TIME[μs]
Figure 24.
Input / Output Voltage - Time
(VCC/VEE=+15V/-15V, Av=0dB,
RL=2kΩ, CL=100pF, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
15/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
8
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3474Y, BA3474W
1600
12
SUPPLY CURRENT [mA]
POWER DISSIPATION[mW]
1400
1200
BA3474YFV-C
BA3474WFV-C
1000
800
600
400
10
-40
25℃
8
125℃
6
4
2
200
0
0
0
25
50
75
100
125
150
0
5
15
20
25
30
35
40
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE[℃ ]
Figure 25.
Derating Curve
Figure 26.
Supply Current - Supply Voltage
12
40
35
10
30V
OUTPUT VOLTAGE[V]
SUPPLY CURRENT [mA]
10
36V
8
6
5V
4
3V
30
-40
25
25℃
20
15
125℃
10
2
5
0
0
-50 -25
0
25
50
75
100 125 150
0
AMBIENT TEMPERATURE [℃]
10
20
30
40
SUPPLY VOLTAGE[V]
Figure 27.
Supply Current - Ambient Temperature
Figure 28.
Maximum Output Voltage(High)
- Supply Voltage
(RL=10kΩ)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
16/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3474Y, BA3474W
1. 0
40
OUTPUT VOLTAGE[V]
OUTPUT VOLTAGE[V]
35
30
36V
25
30V
20
15
10
5V
0. 8
0. 6
0. 4
-40℃
125℃
25℃
0. 2
3V
5
0. 0
0
-50 -25
0
25
50
75
0
100 125 150
AMBIENT TEMPERATURE [℃]
20
30
40
SUPPLY VOLTAGE[V]
Figure 29.
Maximum Output Voltage(High)
- Ambient Temperature(RL=10kΩ)
Figure 30.
Maximum Output Voltage(Low)
- Supply Voltage
(RL=10kΩ)
1. 0
OUTPUT SOURCE CURRENT[mA]
100. 0
0. 8
OUTPUT VOLTAGE[V]
10
0. 6
0. 4
3V
5V
36V
30V
0. 2
10.0
125℃
25℃
1. 0
-40℃
0. 1
0. 0
-50
-25
0
25
50
75
100 125 150
0
1
2
3
4
5
6
VCC-OUT[V]
AMBIENT TEMPERATURE [℃]
Figure 31.
Maximum Output Voltage(Low)
- Ambient Temperature
(RL=10kΩ)
Figure 32.
Output Source Current - (VCC-OUT)
(VCC/VEE=5V/0V)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
17/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3474Y, BA3474W
5
INPUT OFFSET VOLTAGE[mV]
-40℃ 25℃
125℃
10.0
1. 0
0. 1
4
3
2
-40℃
25℃
1
0
-1
125℃
-2
-3
-4
-5
0
1
2
3
4
5
6
-20
OUT-VEE[V]
-15
-10
-5
0
5
10
15
COMMON MODE INPUT VOLTAGE[V]
Figure 33.
Output Source Current - (OUT-VEE)
(VCC/VEE=5V/0V)
Figure 34.
Input Offset Voltage Common Mode Input Voltage
(VCC/VEE=15V/-15V)
3
3
INPUT OFFSET VOLTAGE[mV]
INPUT OFFSET VOLTAGE[mV]
OUTPUT SINK CURRENT[mA]
100. 0
2
25℃
-40℃
1
125℃
0
-1
-2
-3
2
36V
30V
1
5V
0
-1
-2
-3
0
5
10
15
20
25
30
35
-50 -25
40
0
25
50
75
100 125 150
SUPPLY VOLTAGE[V]
AMBIENT TEMPERATURE[℃]
Figure 35.
Input Offset Voltage - Supply Voltage
Figure 36.
Input Offset Voltage - Ambient Temperature
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
18/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3474Y, BA3474W
100
25℃
-40℃
80
INPUT BIAS CURRENT[nA]
INPUT BIAS CURRENT[nA]
100
60
125℃
40
20
30V
5V
60
3V
40
20
0
0
0
5
10
15
20
25
30
35
-50
40
SUPPLY VOLTAGE[V]
140
140
LARGE SIGNAL VOLTAGE GAIN[dB]
150
130
120
110
-40℃
100
90
125℃
80
70
60
50
5
10
15
20
25
30
0
25
50
75
100 125 150
Figure 38.
Input Bias Current - Ambient Temperature
150
25℃
-25
AMBIENT TEMPERATURE[℃]
Figure 37.
Input Bias Current - Supply Voltage
LARGE SIGNAL VOLTAGE GAIN[dB]
36V
80
35
130
120
10V
110
30V
100
90
36V
80
70
60
50
40
-50
SUPPLY VOLTAGE[V]
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE[℃]
Figure 39.
Large Signal Voltage Gain
- Supply Voltage
Figure 40.
Large Signal Voltage Gain
- Ambient Temperature
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
19/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3474Y, BA3474W
140
150
130
140
120
130
36V
110
CMRR[dB]
CMRR[dB]
120
125℃
110
100
30V
100
90
25℃
80
-40℃
90
80
70
70
60
60
50
50
40
40
0
5
10
15
20
25
30
35
5V
-50
40
SUPPLY VOLTAGE[V]
0
25
50
75
100 125 150
AMBIENT TEMPERATURE[℃]
Figure 41.
Common Mode Rejection Ratio
- Supply Voltage
Figure 42.
Common Mode Rejection Ratio
- Ambient Temperature
16
16
14
14
-40℃
SLEW RATE(RISE)[V/μs]
SLEW RATE(RISE)[V/μs]
-25
12
25℃
10
8
125℃
6
4
36V
30V
12
10
15V
8
6
5V
3V
4
2
2
0
0
0
5
10
15
20
25
30
35
-50
40
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE[℃]
SUPPLY VOLTAGE[V]
Figure 43.
Slew Rate L-H - Supply Voltage
RL=10kΩ
Figure 44.
Slew Rate L-H Ambient Temperature
RL=10kΩ
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
20/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
○BA3474Y, BA3474W
50
12
0
-30
GAIN
30
-60
20
-90
10
-120
0
PHASE[deg]
VOLTAGE GAIN[dB]
40
-150
INPUT/OUTPUT VOLTAGE[V]
10
PHASE
8
6
OUTPUT
4
INPUT
2
0
-2
-4
-6
-8
-10
-10
1
10
100
1000
-180
10000
-12
0
FREQUENCY[kHz]
1
2
3
4
5
6
7
TIME[μs]
Figure 45.
Voltage Gain・Phase - Frequency
(VCC/VEE=+15V/-15V, Av=40dB
RL=2kΩ, CL=100pF, Ta=25℃)
Figure 46.
Input / Output Voltage - Time
(VCC/VEE=+15V/-15V, Av=0dB,
RL=2kΩ, CL=100pF, Ta=25℃)
INPUT/OUTPUT VOLTAGE[mV]
100
80
INPUT
60
40
OUTPUT
20
0
-20
-40
-60
-80
-100
0.0
0.5
1.0
1.5
2.0
2.5
TIME[μs]
Figure 47.
Input / Output Voltage - Time
(VCC/VEE=+15V/-15V, Av=0dB,
RL=2kΩ, CL=100pF, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
21/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
8
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
●Application Information
NULL method condition for Test circuit1
VCC, VEE, EK, Vicm Unit : V
VF
Parameter
S1
S2
S3
VCC
VEE
EK
Vicm
Calculation
Input Offset Voltage
VF1
ON
ON
OFF
15
-15
0
0
1
Input Offset Current
VF2
OFF
OFF
OFF
15
-15
0
0
2
VF3
OFF
ON
VF4
ON
OFF
OFF
15
-15
0
0
3
ON
ON
ON
15
-15
+10
0
15
-15
-10
0
ON
ON
OFF
15
-15
0
-15
15
-15
0
13
ON
ON
OFF
Input Bias Current
VF5
Large Signal Voltage Gain
VF6
Common-mode Rejection Ratio
(Input Common-mode Voltage Range)
VF7
VF8
VF9
Power Supply Rejection Ratio
VF10
2
-2
0
0
18
-18
0
0
4
5
6
-Calculation-
1. Input Offset Voltage (Vio)
Vio 
VF1
1+ RF / RS
0.1μF
[V]
2. Input Offset Current (Iio)
Iio 
VF2 - VF1
Ri × (1 + RF / RS)
RF=50kΩ
[A]
SW1
0.1μF
500kΩ
VCC
EK
3. Input Bias Current (Ib)
Ib 
VF4 - VF3
2 × Ri × (1 + RF / RS)
RS=50Ω
500kΩ
[A]
DUT
NULL
SW3
4. Large Signal Voltage Gain (Av)
ΔEK × (1+ RF/RS)
Av  20 × Log
VF5 - VF6
15V
Ri=10kΩ
RS=50Ω
1000pF
Ri=10kΩ
V
RL
Vicm
SW2
[dB]
-15V
VEE
50kΩ
5. Common-mode Rejection Ratio (CMRR)
CMRR  20 × Log
ΔVicm × (1+ RF/RS)
[dB]
VF8 - VF7
Figure 48. Test circuit1 (one channel only)
6. Power Supply Rejection Ratio (PSRR)
PSRR  20 × Log
ΔVcc × (1+ RF/RS)
[dB]
VF10 - VF9
Switch Condition for Test Circuit 2
SW No.
SW
1
SW
2
SW
3
SW
4
SW
5
SW
6
SW
7
SW
8
SW
9
SW
10
SW
11
SW
12
SW
13
SW
14
Supply Current
OFF OFF OFF
ON
OFF
ON
OFF OFF OFF OFF OFF OFF OFF OFF
Maximum Output Voltage High
OFF OFF
ON
OFF OFF
ON
OFF OFF
OFF OFF OFF
ON
OFF
Maximum Output Voltage Low
OFF OFF
ON
OFF OFF
ON
OFF OFF OFF OFF OFF OFF
ON
OFF
Output Source Current
OFF OFF
ON
OFF OFF
ON
OFF OFF OFF OFF OFF OFF OFF
ON
Output Sink Current
OFF OFF
ON
OFF OFF
ON
OFF OFF OFF OFF OFF OFF OFF
ON
Slew Rate
OFF OFF OFF
ON
ON
ON
OFF OFF OFF OFF
Gain Bandwidth Product
OFF
ON
OFF OFF
ON
ON
OFF OFF
ON
ON
OFF OFF OFF OFF
Equivalent Input Noise Voltage
ON
OFF OFF OFF
ON
ON
OFF OFF OFF OFF
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
ON
OFF OFF OFF
22/29
ON
ON
OFF OFF OFF
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
VF
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
Voltage
VH
VL
Input Voltage Waveform
time
Voltage
電圧
90%
VH
ΔV
C
VL
10%
Δt
Output Voltage Waveform
出力電圧波形
Figure 50. Slew rate input output wave
Figure 49. Test Circuit 2 (each Op-Amp)
VCC
VCC
R1//R2
R1//R2
OTHER
CH
VEE
R1
VIN
time
時間
VEE
R2
V
OUT1
=0.5[Vrms]
R1
R2
V
CS=20×log
OUT2
100×OUT1
OUT2
Figure 51. Test circuit 3(Channel Separation)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
23/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
●Examples of circuit
○Voltage follower
Voltage gain is 0dB.
VCC
Using this circuit, the output voltage (OUT) is
configured to be equal to the input voltage (IN). This
circuit also stabilizes the output voltage (OUT) due to
high input impedance and low output impedance.
Computation for output voltage (OUT) is shown below.
OUT
OUT=IN
IN
VEE
Figure 52. Voltage follower circuit
○Inverting amplifier
For inverting amplifier, input voltage (IN) is amplified
by a voltage gain and depends on the ratio of R1 and
R2. The out-of-phase output voltage is shown in the
next expression
VCC
R1
OUT=-(R2/R1)・IN
IN
OUT
R1//R2
This circuit has input impedance equal to R1.
VEE
Figure 53. Inverting amplifier circuit
○Non-inverting amplifier
For non-inverting amplifier, input voltage (IN) is
amplified by a voltage gain, which depends on the ratio
of R1 and R2. The output voltage (OUT) is in-phase
with the input voltage (IN) and is shown in the next
expression.
VCC
OUT
IN
OUT=(1 + R2/R1)・IN
Effectively, this circuit has high input impedance since
its input side is the same as that of the operational
amplifier.
VEE
Figure 54. Non-inverting amplifier circuit
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
24/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
●Power Dissipation
Power dissipation (total loss) indicates the power that the IC can consume at Ta=25°C (normal temperature). As the IC
consumes power, it heats up, causing its temperature to be higher than the ambient temperature. The allowable
temperature that the IC can accept is limited. This depends on the circuit configuration, manufacturing process, and
consumable power.
Power dissipation is determined by the allowable temperature within the IC (maximum junction temperature) and the
thermal resistance of the package used (heat dissipation capability). Maximum junction temperature is typically equal to the
maximum storage temperature. The heat generated through the consumption of power by the IC radiates from the mold
resin or lead frame of the package. Thermal resistance, represented by the symbol θja°C/W, indicates this heat dissipation
capability. Similarly, the temperature of an IC inside its package can be estimated by thermal resistance.
Figure 55(a) shows the model of the thermal resistance of the package. The equation below shows how to compute for the
Thermal resistance (θja), given the ambient temperature (Ta), junction temperature (Tj), and power dissipation (Pd).
θja = (Tjmax - Ta) / Pd
℃/W
・・・・・
(Ⅰ)
The Derating curve in Figure 55(b) indicates the power that the IC can consume with reference to ambient temperature.
Power consumption of the IC begins to attenuate at certain temperatures. This gradient is determined by Thermal
resistance (θja), which depends on the chip size, power consumption, package, ambient temperature, package condition,
wind velocity, etc. This may also vary even when the same of package is used. Thermal reduction curve indicates a
reference value measured at a specified condition. Figure 56(c) and 56(d) shows an example of the derating curve for
BA3472Y, BA3472W, BA3474Y and BA3474W.
PowerLSIの
dissipation
LSI [W]
消 費 電 力of[W]
θja=(Tjmax-Ta)/Pd ℃/W
Pd (max)
θja2 < θja1
P2
Ta [℃] Ta [℃]
周囲温度
Ambient
temperature
θ' ja2
P1
θ ja2
Tj ' (max) Tj (max)
θ' ja1
Chip surface temperature Tj [℃]
チップ 表面温度 Tj [℃]
Power dissipation Pd [W]
0
消費電力 P [W]
25
50
θ ja1
75
100
125
150
] [℃]
囲 温 度 Ta [℃Ta
Ambient 周
temperature
(a) Thermal resistance
(b) Derating curve
Figure 55. Thermal resistance and derating curve
1600
1075mW(*19)
1400
BA3472YF-C
1000
POWER DISSIPATION[mW]
POWER DISSIPATION [mW]
1200
BA3472YFV-C
BA3472WFV-C
835mW(*20)
800
BA3472YFVM-C
750mW(*21)
600
400
200
1350mW(*22)
1200
BA3474YFV-C
BA3472WFV-C
1000
800
600
400
200
0
0
0
25
50
75
100
125
0
150
AMBIENT TEMPERATURE [℃]
25
50
75
100
125
150
AMBIENT TEMPERATURE[℃ ]
(c)BA3472Y, BA3472W
(d)BA3474Y, BA3474W
(*19)
(*20)
(*21)
(*22)
Unit
8.6
6.7
6.0
10.8
mW/℃
When using the unit above Ta=25℃, subtract the value above per degree℃.
Mounted on a FR4 glass epoxy 4 layers PCB 70mm×70mm×1.6mm (occupied copper area:70mm×70mm).
Figure 56. Derating curve
<Reference>
When the part is mounted on FR4 glass epoxy 4 layers PCB 70mm×70mm×1.6mm (occupied copper area:70mm×70mm).
SSOP-B8 package : Pd at 125℃ is 165mW so Vcc has to be below 27V.
: Pd at 125℃ is 150mW so Vcc has to be below 25V.
MSOP8 package
SSOP-B14 package : Pd at 125℃ is 270mW so Vcc has to be below 22V.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
25/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
●Operational Notes
1) Unused circuits
When there are unused op-amps, it is recommended that they are
connected as in Figure 57, setting the non-inverting input terminal to a
potential within the in-phase input voltage range (Vicm).
2) Input voltage
Applying VEE +36V to the input terminal is possible without causing
deterioration of the electrical characteristics or destruction, regardless of
the supply voltage. However, this does not ensure normal circuit operation.
Please note that the circuit operates normally only when the input voltage is
within the common mode input voltage range of the electric characteristics.
Datasheet
VCC
+
Connect
to Vicm
Vicm
VEE
Figure 57. Example of
application circuit for unused op-amp
3) Power supply (single / dual)
The op-amp operates when the voltage supplied is between VCC and VEE.
Therefore, the single supply op-amp can be used as dual supply op-amp as
well.
4) Power dissipation Pd
Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics including
reduced current capability due to the rise of chip temperature. Therefore, please take into consideration the power
dissipation (Pd) under actual operating conditions and apply a sufficient margin in thermal design. Refer to the thermal
derating curves for more information.
5) Short-circuit between pins and erroneous mounting
Be careful when mounting the IC on printed circuit boards. The IC may be damaged if it is mounted in a wrong orientation
or if pins are shorted together. Short circuit may be caused by conductive particles caught between the pins.
6) Operation in a strong electromagnetic field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
7) Radiation
This IC is not designed to withstand radiation.
8) IC handling
Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuations of the electrical
characteristics due to piezo resistance effects.
9) Board inspection
Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every
process is recommended. In addition, when attaching and detaching the jig during the inspection phase, make sure that
the power is turned OFF before inspection and removal. Furthermore, please take measures against ESD in the
assembly process as well as during transportation and storage.
10) Output capacitor
If a large capacitor is connected between the output pin and GND pin, current from the charged capacitor will flow into the
output pin and may destroy the IC when the VCC or VIN pin is shorted to ground or pulled down to 0V. Use a capacitor
smaller than 1uF between output and GND.
11) Oscillation by output capacitor
Please pay attention to the oscillation by output capacitor and in designing an application of negative feedback loop
circuit with these ICs.
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a
reference to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
26/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
●Physical Dimensions Tape and Reel Information
SOP8
<Tape and Reel information>
5.0±0.2
(MAX 5.35 include BURR)
+6°
4° −4°
5
6
6.2±0.3
4.4±0.2
0.3MIN
7
0.9±0.15
8
1 2
3
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
4
0.595
1.5±0.1
+0.1
0.17 -0.05
S
S
0.11
0.1
1.27
Direction of feed
1pin
0.42±0.1
Reel
(Unit : mm)
∗ Order quantity needs to be multiple of the minimum quantity.
SSOP-B8
<Tape and Reel information>
3.0±0.2
(MAX 3.35 include BURR)
8
7
6
5
Tape
Embossed carrier tape
Quantity
2500pcs
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
0.3MIN
6.4 ± 0.3
4.4 ± 0.2
Direction
of feed
2
3
4
0.1
1.15±0.1
1
0.15±0.1
S
(0.52)
0.65
0.1 S
+0.06
0.22 −0.04
0.08
Direction of feed
1pin
M
Reel
(Unit : mm)
∗ Order quantity needs to be multiple of the minimum quantity.
MSOP8
<Tape and Reel information>
2.8±0.1
4.0±0.2
8 7 6 5
0.6±0.2
+6°
4° −4°
0.29±0.15
2.9±0.1
(MAX 3.25 include BURR)
Tape
Embossed carrier tape
Quantity
3000pcs
Direction
of feed
TR
The direction is the 1pin of product is at the upper right when you hold
( reel on the left hand and you pull out the tape on the right hand
)
1 2 3 4
1PIN MARK
1pin
+0.05
0.145 −0.03
0.475
+0.05
0.22 −0.04
0.08±0.05
0.75±0.05
0.9MAX
S
0.08 S
Direction of feed
0.65
Reel
(Unit : mm)
∗ Order quantity needs to be multiple of the minimum quantity.
SSOP-B14
<Tape and Reel information>
5.0 ± 0.2
8
0.3Min.
4.4 ± 0.2
6.4 ± 0.3
14
1
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
7
0.10
1.15 ± 0.1
0.15 ± 0.1
0.65
0.1
0.22 ± 0.1
1pin
(Unit : mm)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
Reel
27/29
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
●Marking Diagrams
SOP8(TOP VIEW)
Datasheet
SSOP-B8(TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
MSOP8(TOP VIEW)
SSOP-B14(TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
Product Name
BA3472Y
Package Type
Marking
F
SOP8
3472Y
FV
SSOP-B8
72Y
MSOP8
3472Y
SSOP-B8
72W
FVM
BA3472W
BA3474Y
FV
3474Y
SSOP-B14
BA3474W
3474W
●Land pattern data
All dimensions in mm
Land length
Land width
≧ℓ 2
b2
PKG
Land pitch
e
Land space
MIE
SOP8
1.27
4.60
1.10
0.76
SSOP-B8
SSOP-B14
0.65
4.60
1.20
0.35
MSOP8
0.65
2.62
0.99
0.35
b2
e
MIE
ℓ2
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
28/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
BA3472Yxxx-C, BA3474YFV-C, BA3472WFV-C, BA3474WFV-C
Datasheet
●Revision History
Date
Revision
Changes
24.Aug.2012
001
New Release
20.Dec.2012
002
BA3472Y, BA3474Y series and land pattern data inserted.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
29/29
TSZ02201-0RAR1G200540-1-2
20.DEC.2012 Rev.002
Datasheet
Notice
General Precaution
1. Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
Precaution on using ROHM Products
1.
If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Datasheet
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2.
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Precautions Regarding Application Examples and External Circuits
1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights
1.
All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Datasheet
Other Precaution
1.
The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
2.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
3.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
4.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
5.
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Similar pages