Rohm BA4558RFVT-TR Low noise operational amplifier Datasheet

Datasheet
Operational Amplifiers
Low Noise Operational Amplifiers
BA4558xxx, BA4558Rxxx
●General Description
Normal BA4558 and high-reliability BA4558R integrate two independent Op-Amps on a single chip Especially, this series is
suitable for any audio applications due to low noise and low distortion characteristics and are usable for other many
applications by wide operating supply voltage range.BA4558R is high-reliability products with extended operating
temperature range and high ESD tolerance.
●Features
 High voltage gain, low noise, low distortion
 Wide operating supply voltage
 Internal ESD protection
 Wide operating temperature Range
●Packages
W(Typ.) x D(Typ.) x H(Max.)
MSOP8
2.90mm x 4.00mm x 0.90mm
SSOP-B8
3.00mm x 6.40mm x 1.35mm
SOP8
5.00mm x 6.20mm x 1.71mm
TSSOP-B8
3.00mm x 6.40mm x 1.20mm
SOP-J8
4.90mm x 6.00mm x 1.65mm
●Key Specification
 Wide Operating Supply Voltage
(split supply):±4.0V to ±15V
 Wide Temperature Range: BA4558: -40°C to +85°C
BA4558R: -40°C to +105°C
 High Slew Rate:
1V/µs(Typ.)
 Total Harmonic Distortion :
0.005%(Typ.)
 Input Referred Noise Voltage :
12 nV/ Hz (Typ.)
Maximum Operation Temperature
●Selection Guide
Slew Rate
Normal
Dual
1V/µs
Slew Rate
High Reliability
Dual
1V/µs
+85°C
BA4558F
BA4558FV
BA4558FVT
BA4558FVM
BA4558FJ
+105°C
BA4558RF
BA4558RFV
BA4558RFVT
BA4558RFVM
BA4558RFJ
●Block Diagram
VCC
-IN
VOUT
+IN
VEE
Fig. 1 Simplified schematic
○Product structure:Silicon monolithic integrated circuit
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・00
○This product is not designed protection against radioactive rays.
1/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
●Pin Configuration(TOP VIEW)
OUT1 1
-IN1
2
+IN1
3
VEE
4
SOP8
SSOP-B8
BA4558F
BA4558RF
BA4558FV
BA4558RFV
8 VCC
7 OUT2
CH1
- +
6 -IN2
CH2
+ -
5 +IN2
T SSOP-B8
BA4558FVT
BA4558RFVT
M SOP8
SOP- J8
BA4558FVM
BA4558RFVM
BA4558FJ
BA4558RFJ
Package
SOP8
SSOP-B8
TSSOP-B8
MSOP8
SOP-J8
BA4558F
BA4558RF
BA4558FV
BA4558RFV
BA4558FVT
BA4558RFVT
BA4558FVM
BA4558RFVM
BA4558FJ
BA4558RFJ
●Ordering Information
B
A
4
5
5
8
x
x
x
x
-
Packaging and forming specification
E2: Embossed tape and reel
(SOP8/SSOP-B8/TSSOP-B8/SOP-J8)
TR: Embossed tape and reel
(MSOP8)
Package
F:
SOP8
FV: SSOP-B8
FJ: SOP-J8
FVT: TSSOP-B8
FVM: MSOP8
Part Number
BA4558xxx
BA4558Rxxx
xx
●Line-up
Topr
Operating Supply
Voltage
(split supply)
Supply
Current
(Typ.)
Slew
Rate
(Typ.)
-40°C to +85°C
±4.0V to ±15.0V
3mA
1V/µs
-40°C to +105°C
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
2/26
Orderable
Part Number
Package
SOP8
Reel of 2500
BA4558F-E2
SSOP-B8
Reel of 2500
BA4558FV-E2
TSSOP-B8
Reel of 3000
BA4558FVT-E2
MSOP8
Reel of 3000
BA4558FVM-TR
SOP-J8J
Reel of 2500
BA4558FJ-E2
SOP8
Reel of 2500
BA4558RF-E2
SSOP-B8
Reel of 2500
BA4558RFV-E2
TSSOP-B8
Reel of 3000
BA4558RFVT-E2
MSOP8
Reel of 3000
BA4558RFVM-TR
SOP-J8
Reel of 2500
BA4558RFJ-E2
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
●Absolute Maximum Ratings (Ta=25℃)
○BA4558, BA4558R
Ratings
Parameter
Symbol
Unit
BA4558
Supply Voltage
VCC-VEE
+36
Pd
V
552
*1*5
690*1*5
SSOP-B8
500*2*5
625*2*5
TSSOP-B8
500*2*5
625*2*5
*3*5
*3*5
SOP8
Power dissipation
BA4558R
mW
MSOP8
470
587
SOP-J8
540*4*5
675*4*5
Vid
VCC-VEE
+36
V
Input common-mode voltage range
Vicm
VEE to VCC
(VEE-0.3) to VEE+36
V
Operating Supply Voltage
Vopr
Operating Temperature
Topr
-40 to +85
-40 to +105
℃
Storage Temperature
Tstg
-55 to +125
-55 to +150
℃
Tjmax
+125
Differential Input Voltage*5
Maximum Junction Temperature
+8 to +30 (±4 to ±15)
V
+150
℃
Note: Absolute maximum rating item indicates the condition which must not be exceeded.
Application of voltage in excess of absolute maximum rating or use out absolute maximum rated temperature environment
may cause deterioration of characteristics.
*1
To use at temperature above Ta=25℃ reduce 5.52mW.
*2
To use at temperature above Ta=25℃ reduce 5mW.
*3
To use at temperature above Ta=25℃ reduce 4.7mW.
*4
To use at temperature above Ta=25℃ reduce 5.4mW.
*5
Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm).
*6
The voltage difference between inverting input and non-inverting input is the differential input voltage.
Then input terminal voltage is set to more than VEE.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
3/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
●Electrical Characteristics
○BA4558 (Unless otherwise specified VCC=+15V, VEE=-15V)
Parameter
Symbol
Temperature
Range
Min.
Limits
Typ.
Max.
Unit
Condition
Input Offset Voltage *7
Vio
25℃
-
0.5
6
mV
VOUT=0V
Input Offset Current *7
Iio
25℃
-
5
200
nA
VOUT=0V
Input Bias Current *8
Ib
25℃
-
60
500
nA
VOUT=0V
Supply Current
ICC
25℃
-
3
6
mA
RL=∞, All Op-Amps,
VIN+=0V
Maximum Output Voltage
VOM
25℃
±10
±13
-
25℃
±12
±14
-
Large Signal Voltage Gain
AV
25℃
86
100
-
dB
Vicm
25℃
±12
±14
-
V
Common-mode Rejection Ratio
CMRR
25℃
70
90
-
dB
Ri≦10kΩ
Power Supply Rejection Ratio
PSRR
25℃
76.3
90
-
dB
Ri≦10kΩ
SR
25℃
-
1
-
V/μs AV=0dB, RL≧2kΩ
ft
25℃
-
2
-
MHz RL=2kΩ
THD+N
25℃
-
0.005
-
%
-
12
-
nV/ Hz
-
1.8
-
μVrms RS=100Ω, Vi=0V, DIN-AUDIO
-
105
-
Input Common-mode Voltage Range
Slew Rate
Unity Gain Frequency
Total Harmonic Distortion
Input Referred Noise Voltage
Channel Separation
*7
*8
Vn
CS
RL≧2kΩ
V
RL≧10kΩ
RL≧2kΩ, VOUT=±10V,
Vicm=0V
-
AV=20dB, RL=10kΩ
VIN=0.05Vrms, f=1kHz
RS=100Ω, Vi=0V, f=1kHz
25℃
25℃
dB
f=1kHz
Absolute value
Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
4/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
○BA4558R (Unless otherwise specified VCC=+15V, VEE=-15V, Full range -40℃ to +105℃)
Limits
Temperature
Parameter
Unit
Symbol
Range
Min.
Typ.
Max.
Input Offset Voltage *9
Vio
Input Offset Current *9
Iio
Input Bias Current *10
Ib
Supply Current
Maximum Output Voltage
Large Signal Voltage Gain
Input Common-mode Voltage Range
ICC
VOM
AV
Vicm
25℃
-
0.5
6
Full range
-
-
7
25℃
-
5
200
Full range
-
-
200
25℃
-
60
500
Full range
-
-
800
25℃
-
3
6
Full range
-
-
6.5
25℃
±10
±13
-
Full range
±10
-
-
25℃
±12
±14
-
25℃
86
100
-
Full range
83
-
-
25℃
±12
±14
-
Full range
±12
-
-
Condition
mV
VOUT=0V
nA
VOUT=0V
nA
VOUT=0V
mA
RL=∞, All Op-Amps,
VIN+=0V
RL≧2kΩ
V
RL≧10kΩ
dB
RL≧2kΩ, VOUT=±10V,
Vicm=0V
V
-
Common-mode Rejection Ratio
CMRR
25℃
70
90
-
dB
Ri≦10kΩ
Power Supply Rejection Ratio
PSRR
25℃
76.5
90
-
dB
Ri≦10kΩ
SR
25℃
-
1
-
V/μs
ft
25℃
-
2
-
MHz RL=2kΩ
THD+N
25℃
-
0.005
-
%
-
12
-
nV/ Hz
RS=100Ω, Vi=0V, f=1kHz
-
1.8
-
μVrms
RS=100Ω,
Vi=0V, DIN-AUDIO
-
105
-
dB
R1=100Ω, f=1kHz
Slew Rate
Unity Gain Frequency
Total Harmonic Distortion
Input Referred Noise Voltage
Channel Separation
*9
*10
Vn
CS
AV=0dB, RL=2kΩ
CL=100pF
AV=20dB, RL=10kΩ
VIN=0.05Vrms, f=1kHz
25℃
25℃
Absolute value
Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
5/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
Description of electrical characteristics
Described here are the terms of electric characteristics used in this datasheet. Items and symbols used are also shown.
Note that item name and symbol and their meaning may differ from those on another manufacture’s document or general document.
1. Absolute maximum ratings
Absolute maximum rating item indicates the condition which must not be exceeded. Application of voltage in excess of
absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of
characteristics.
1.1 Power supply voltage (VCC-VEE)
Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power
supply terminal without deterioration or destruction of characteristics of internal circuit.
1.2 Differential input voltage (Vid)
Indicates the maximum voltage that can be applied between non-inverting terminal and inverting terminal without
deterioration and destruction of characteristics of IC.
1.3 Input common-mode voltage range (Vicm)
Indicates the maximum voltage that can be applied to non-inverting terminal and inverting terminal without
deterioration or destruction of characteristics. Input common-mode voltage range of the maximum ratings not assure
normal operation of IC. When normal operation of IC is desired, the input common-mode voltage of characteristics
item must be followed.
1.4 Power dissipation (Pd)
Indicates the power that can be consumed by specified mounted board at the ambient temperature 25℃(normal temperature).
As for package product, Pd is determined by the temperature that can be permitted by IC chip in the package
(maximum junction temperature)and thermal resistance of the package.
2. Electrical characteristics item
2.1 Input offset voltage (Vio)
Indicates the voltage difference between non-inverting terminal and inverting terminal. It can be translated into the
input voltage difference required for setting the output voltage at 0V.
2.2 Input offset current (Iio)
Indicates the difference of input bias current between non-inverting terminal and inverting terminal.
2.3 Input bias current (Ib)
Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias current at
non-inverting terminal and input bias current at inverting terminal.
2.4 Input common-mode voltage range (Vicm)
Indicates the input voltage range where IC operates normally.
2.5 Large signal voltage gain (AV)
Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal
and Inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage.
Av = (Output voltage fluctuation) / (Input offset fluctuation)
2.6 Circuit current (ICC)
Indicates the IC current that flows under specified conditions and no-load steady status.
2.7 Output saturation voltage (VOM)
Signifies the voltage range that can be output under specific output conditions.
2.8 Common-mode rejection ratio (CMRR)
Indicates the ratio of fluctuation of input offset voltage when in-phase input voltage is changed. It is normally the
fluctuation of DC.
CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation)
2.9 Power supply rejection ratio (PSRR)
Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. It is normally the fluctuation
of DC.
PSRR = (Change of power supply voltage) / (Input offset fluctuation)
2.10 Channel Separation (CS)
Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage
of driven channel.
2.11 Slew Rate (SR)
SR is a parameter that shows movement speed of operational amplifier. It indicates rate of variable output voltage
as unit time.
2.12 Transition Frequency (ft)
Indicates a frequency where the voltage gain of operational amplifier is 1.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
6/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
2.13 Total Harmonic Distortion (THD+N)
Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage
of driven channel.
2.14 Input Referred Noise Voltage (Vn)
Indicates a noise voltage generated inside the operational amplifier equivalent by ideal voltage source connected in
series with input terminal.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
7/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
●Typical Performance Curves
○ BA4558
5.0
800
BA4558F
BA4558FJ
600
4.0
SUPPLY CURRENT [mA]
POWER DISSIPATION [mW] .
.
1000
BA4558FV/FVT
BA4558FVM
400
25℃
-40℃
3.0
2.0
85℃
1.0
200
0.0
0
0
85
25
50
75
100
AMBIENT TEMPERTURE [ ℃] .
0
125
MAXIMUM OUTPUT VOLTAGE SWING [VP-P]
SUPPLY CURRENT [mA]
5.0
4.0
±15V
3.0
2.0
±7.5 V
1.0
0.0
-50
-25
0
25
50
75
AMBIENT TEMPERATURE [℃]
10
15
20
25
SUPPLY VOLTAGE [V]
30
35
Fig.3
Supply Current – Supply Voltage
Fig.2
Derating Curve
±4 V
5
100
30
25
20
15
10
5
0
0.1
Fig.4
Supply Current – Ambient Temperature
1
LOAD RESISTANCE [kΩ]
10
Fig.5
Maximum Output Voltage Swing
- Load Resistance
(VCC/VEE=+15V/-15V, Ta=25℃)
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
8/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
○ BA4558
20
20
15
15
10
10
OUTPUT VOLTAGE [V]
OUTPUT VOLTAGE [V]
VOH
VOH
5
0
-5
VOL
-10
5
0
-5
-10
VOL
-15
-15
-20
-20
0.1
1
LOAD RESISTANCE [kΩ]
±2
10
20
20
15
15
10
OUTPUT VOLTAGE [V]
OUTPUT VOLTAGE [V]
±6 ±8 ±10 ±12 ±14 ±16 ±18
SUPPLY VOLTAGE [V]
Fig.7
Maximum Output Voltage
- Supply Voltage
(RL=2kΩ, Ta=25℃)
Fig.6
Maximum Output Voltage
– Load Resistance
(VCC/VEE=+15V/-15V, Ta=25℃)
VOH
5
0
-5
VOL
-10
10
VOH
5
0
-5
VOL
-10
-15
-15
-20
-50
±4
-20
-25
0
25
50
75
0
100
5
10
15
20
AMBIENT TEMPERATURE [℃]
OUTPUT CURRENT [mA]
Fig.8
Maximum Output Voltage
- Ambient Temperature
(VCC/VEE=+15V/-15V, RL=2kΩ)
Fig.9
Maximum Output Voltage
- Output Current
(VCC/VEE=+15V/-15V, Ta=25℃)
25
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
9/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
○ BA4558
6
INPUT OFFSET VOLTAGE [mV]
INPUT OFFSET VOLTAGE [mV]
6
4
-40℃
2
0
85℃
25℃
-2
-4
4
±4V
2
±7.5V
0
±15V
-2
-4
-6
-6
±0
±2
±4
±6
±8
-50
±10 ±12 ±14 ±16
-25
0
25
50
75
100
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
Fig.11
Input Offset Voltage - Ambient Temperature
(Vicm=0V, Vout=0V)
Fig.10
Input Offset Voltage - Supply Voltage
(Vicm=0V, Vout=0V)
80
.
80
70
INPUT BIAS CURRENT [nA]
INPUT BIAS CURRENT [nA]
70
85℃
60
50
40
-40℃
25℃
30
20
50
40
±7.5V
20
10
0
0
±2
±4
±6
±8
±15V
30
10
±0
±4V
60
-50
±10 ±12 ±14 ±16
SUPPLY VO LTAGE [V]
-25
0
25
50
75
100
AMBIENT TEMPERATURE [℃]
Fig.12
Input Bias Current - Supply Voltage
(Vicm=0V, Vout=0V)
Fig.13
Input Bias Current - Ambient Temperature
(Vicm=0V, Vout=0V)
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
10/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
20
30
25℃
10
INPUT OFFSET CURRENT [nA]
.
30
INPUT OFFSET CURRENT [nA]
○ BA4558
-40℃
0
-10
85℃
-20
20
10
±4V
0
±15V
-10
-20
-30
-30
±0
±2
-50
±4 ±6 ±8 ±10 ±12 ±14 ±16
SUPPLY VOLTAGE [V]
COMMON MODE REJECTION RATIO [dB]
4
3
-40℃
25℃
1
0
-1
85℃
-2
-3
-4
-5
0
0
25
50
75
100
Fig.15
Input Offset Current Ambient Temperature
(Vicm=0V, Vout=0V)
5
2
-25
AMBIENT TEMPERATURE [°C]
Fig.14
Input Offset Current - Supply Voltage
(Vicm=0V, Vout=0V)
INPUT OFFSET VOLTAGE [mV]
±7.5V
150
125
100
75
50
25
0
-50
2
4
6
8
COMMON MODE INPUT VOLTAGE [V]
-25
0
25
50
75
AMBIENT TEMPERATURE [°C]
100
Fig.17
Common Mode Rejection Ratio
- Ambient Temperature
(VCC/VEE=+15V/-15V, Vicm=-12V to +12V)
Fig.16
Input Offset Voltage
- Common Mode Input Voltage
(VCC=8V, Vout=4V)
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
11/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
2.0
.
150
125
SLEW RATE [V/µs]
POWER SUPPLY REJECTION RATIO [dB]
.
○ BA4558
100
75
50
1.5
1.0
0.5
25
0.0
0
-50
-25
0
25
50
75
±2
100
AMBIENT TEMPERATURE [℃]
TOTAL HARMONIC DISTORTION [%] .
INTPUT REFERRED NOISE VOLTAGE
[nV/ √Hz]
80
60
40
20
0
10
100
FREQUENCY [kHz]
±6
±8 ±10 ±12
SUPPLY VOLTAGE [V]
±14
±16
Fig.19
Slew Rate - Supply Voltage
(CL=100pF, RL=2kΩ, Ta=25℃)
Fig.18
Power Supply Rejection Ratio
- Ambient Temperature
(VCC/VEE=+4V/-4V to +15V/-15V)
1
±4
1
20kHz
0.1
0.01
1kHz
0.001
20Hz
0.0001
1000
0.1
1
OUTPUT VOLTAGE [Vrms]
10
Fig.21
Total Harmonic Distortion -Output Voltage
RL=2kΩ, 80kHz-LPF, Ta=25℃)
Fig.20
Equivalent Input Noise Voltage - Frequency
(VCC/VEE=+15V/-15V, RS=100Ω, Ta=25℃)
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
12/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
30
60
0
25
20
15
10
5
0
1
10
100
50
-30
40
-60
30
-90
GAIN
20
-120
10
-150
0
1000
2
3
4
5
6
7
PHASE [deg]
PHASE
VOLTAGE GAIN [dB]
MAXIMUM OUTPUT VOLTAGE SWING [VP-P]
○ BA4558
-180
8
10 1.E+
10 1.E+
10 1.E+
10
10 10
1.1E+ 1.E+
1.E+ 10
1. E+ 10
1.E+ 1.E+
00
01
02
03
04
05
06
07
08
FREQUENCY [kHz]
FREQUENCY [Hz]
Fig.22
Maximum Output Voltage Swing - Frequency
(VCC/VEE=+15V/-15V, RL=2kΩ, Ta=25℃)
Fig.23
Voltage Gain - Frequency
(VCC/VEE=+15V/-15V, AV=40dB, RL=2kΩ, Ta=25℃)
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
13/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
○ BA4558R
5.0
BA4558RF
800
SUPPLY CURRENT [mA]
PO WER DISSIPATION [mW] .
.
1000
BA4558RFJ
BA4558RFV/FVT
600
BA4558RFVM
400
200
-40℃
4.0
25℃
3.0
2.0
105℃
1.0
0.0
0
0
105
25
50
75
100
AMBIENT TEMPERTURE [ ℃] .
0
125
SUPPLY CURRENT [mA]
MAXIMUM OUTPUT VOLTAGE SWING [VP-P]
5.0
±15V
3.0
±4 V
2.0
±7.5 V
1.0
0.0
-50
-25
0
25
50
75 100
AMBIENT TEMPERATURE [℃]
10
15
20
25
SUPPLY VOLTAGE [V]
30
35
Fig.25
Supply Current - Supply Voltage
Fig.24
Derating Curve
4.0
5
125
30
25
20
15
10
5
0
0.1
1
10
LOAD RESISTANCE [kΩ]
Fig.27
Maximum Output Voltage Swing
- Load Resistance
(VCC/VEE=+15V/-15V, Ta=25℃)
Fig.26
Supply Current - Ambient Temperature
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
14/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
20
20
15
15
10
OUTPUT VOLTAGE [V]
OUTPUT VOLTAGE [V]
○ BA4558R
VOH
5
0
-5
VOL
-10
VOH
10
5
0
-5
-10
VOL
-15
-15
-20
-20
0.1
1
LOAD RESISTANCE [kΩ]
±4
10
±6
±8
±10
±12
±14
SUPPLY VOLTAGE [V]
Fig.29
Maximum Output Voltage
- Supply Voltage
(RL=2kΩ, Ta=25℃)
20
20
15
15
10
OUTPUT VOLTAGE [V]
OUTPUT VOLTAGE [V]
Fig.28
Maximum Output Voltage
- Load Resistance
(VCC/VEE=+15V/-15V, Ta=25℃)
VOH
5
0
-5
VOL
-10
-15
-20
-50
±16
10
VOH
5
0
-5
VOL
-10
-15
-20
-25
0
25
50
75
100
125
0
AMBIENT TEMPERATURE [℃]
5
10
15
20
25
OUTPUT CURRENT [mA]
Fig.30
Maximum Output Voltage
- Ambient Temperature
(VCC/VEE=+15V/-15V, RL=2kΩ)
Fig.31
Maximum Output Voltage
- Output Current
(VCC/VEE=+15V/-15V, Ta=25℃)
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
15/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
6
6
4
4
INPUT OFFSET VOLTAGE [mV]
INPUT OFFSET VOLTAGE [mV]
○ BA4558R
-40℃
2
25℃
0
105℃
-2
-4
±4V
2
±7.5V
0
-2
±15V
-4
-6
-6
±2
±4
±6
±8
±10
±12
±14
-50
±16
-25
0
25
50
75
100
125
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
Fig.32
Input Offset Voltage - Supply Voltage
(Vicm=0V, Vout=0V)
Fig.33
Input Offset Voltage - Ambient Temperature
(Vicm=0V, Vout=0V)
50
40
40
INPUT BIAS CURRENT [nA]
INPUT BIAS CURRENT [nA]
.
50
30
-40℃
25℃
20
10
105℃
0
30
±4V
±7.5V
20
10
±15V
0
±2
±4
±6
±8
±10
±12
±14
±16
-50
SUPPLY VOLTAGE [V]
-25
0
25
50
75
100
125
AMBIENT TEMPERATURE [℃]
Fig.34
Input Bias Current - Supply Voltage
(Vicm=0V, Vout=0V)
Fig.35
Input Bias Current - Ambient Temperature
(Vicm=0V, Vout=0V)
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
16/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
○ BA4558R
60
INPUT OFFSET CURRENT [nA]
INPUT OFFSET CURRENT [nA]
60
40
-40℃
105℃
20
0
-20
25℃
-40
40
±4V
20
±15V
0
-40
-60
-60
±0
±2
-50
±4 ±6 ±8 ±10 ±12 ±14 ±16
SUPPLY VOLTAGE [V]
Fig.36
Input Offset Current - Supply Voltage
(Vicm=0V, Vout=0V)
COMMON MODE REJECTION RATIO [dB]
4
3
2
1
0
-1
-40℃
-2
25℃
-3
105℃
-4
-5
0
-25
0
25
50
75
100
AMBIENT TEMPERATURE [°C]
125
Fig.37
Input Offset Current - Ambient Temperature
(Vicm=0V, Vout=0V)
5
INPUT OFFSET VOLTAGE [mV]
±7.5V
-20
150
125
100
75
50
25
0
-50
2
4
6
8
COMMON MODE INPUT VOLTAGE [V]
-25
0
25
50
75 100
AMBIENT TEMPERATURE [°C]
125
Fig.39
Common Mode Rejection Ratio
- Ambient Temperature
(VCC/VEE=+15V/-15V, Vicm=-12V to +12V)
Fig.38
Input Offset Voltage
- Common Mode Input Voltage
(VCC=8V, Vout=4V)
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
17/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
150
.
2.0
125
SLEW RATE [V/µs]
POWER SUPPLY REJECTION RATIO [dB]
.
○ BA4558R
100
75
50
1.5
1.0
0.5
25
0
0.0
-50
-25
0
25
50
75
100
125
±2
AMBIENT TEMPERATURE [℃]
±6
±8
±10 ±12
SUPPLY VOLTAGE [V]
±14
±16
Fig.41
Slew Rate - Supply Voltage
(CL=100pF, RL=2kΩ, Ta=25℃)
Fig.40
Power Supply Rejection Ratio
- Ambient Temperature
(VCC/VEE=+4V/-4V to +15V/-15V)
80
1
TOTAL HARMONIC DISTORTION [%]
INTPUT REFERRED NOISE VOLTAGE
[nV/ √Hz]
±4
60
40
20
20kHz
0.1
1kHz
0.01
0.001
20Hz
0.0001
0
1
10
100
FREQUENCY [kHz]
0.1
1000
Fig.42
Equivalent Input Noise Voltage - Frequency
VCC/VEE=+15V/-15V, RS=100Ω, Ta=25℃)
1
OUTPUT VOLTAGE [Vrms]
10
Fig.43
Total Harmonic Distortion - Output Voltage
(VCC/VEE=+15V/-15V,AV=20dB,
RL=2kΩ, 80kHz-LPF, Ta=25℃)
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
18/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
30
60
25
50
-30
40
-60
0
20
15
10
5
0
10
1.E+01
2
10
1.E+02
3
10
1.E+03
4
10
1.E+04
5
10
1.E+05
6
10
1.E+06
FREQUENCY [Hz]
Fig.44
Maximum Output Voltage Swing – Frequency
(VCC/VEE=+15V/-15V, RL=2kΩ, Ta=25℃)
30
-90
GAIN
20
-120
10
-150
PHASE [deg]
PHASE
VOLTAGE GAIN [dB]
MAXIMUM OUTPUT VOLTAGE SWING [VP-P]
○ BA4558R
0
-180
2
3
4
5
6
7
8
1.E+
1.E+ 1.E+
1 1.E+
10 10
10 1.E+
10 1.E+
10 1.E+
10 1.E+
10 1.E+
10
00 01 02 03 04 05 06 07 08
FREQUENCY [Hz]
Fig.45
Voltage Gain - Frequency
(VCC/VEE=+15V/-15V, AV=40dB, RL=2kΩ, Ta=25℃)
(*) The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
19/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
●Application Information
Test circuit1 NULL method
VCC, VEE, EK, Vicm Unit: V
Parameter
VF
S1
S2
S3
VCC
VEE
EK
Vicm
calculation
Input Offset Voltage
VF1
ON
ON
OFF
15
-15
0
0
1
Input Offset Current
VF2
OFF
OFF
OFF
15
-15
0
0
2
VF3
OFF
ON
VF4
ON
OFF
OFF
15
-15
0
0
3
ON
ON
ON
15
-15
0
0
15
-15
0
0
ON
ON
OFF
3
-27
0
0
27
-3
0
0
ON
ON
OFF
Input Bias Current
VF5
Large Signal Voltage Gain
VF6
VF7
Common-mode Rejection Ratio
(Input common-mode Voltage Range)
VF8
VF9
Power Supply
Rejection Ratio
VF10
4
-4
0
0
15
-15
0
0
-Calculation1. Input Offset Voltage (Vio)
VF1
Vio 
[V]
1 + Rf / Rs
5
6
0.1μF
Rf=50kΩ
2. Input Offset Current (Iio)
VF2 - VF1
Iio 
[A]
Ri × (1 + Rf / Rs)
0.1μF
500kΩ
VCC
SW1
3. Input Bias Current (Ib)
VF4 - VF3
Ib 
2 × Ri × (1 + Rf / Rs)
4
EK
+15V
Rs=50Ω
Ri=10kΩ
Ri=10kΩ
[A]
500kΩ
DUT
4. Large Signal Voltage Gain (Av)
ΔEK × (1+ Rf/Rs)
Av  20 × Log
VF5 - VF6
NULL
SW3
Rs=50Ω
Vicm
1000pF
V
RL
SW2
50kΩ
[dB]
VF
VEE
-15V
Fig. 46 Test circuit1 (one channel only)
5. Common-mode Rejection Ration (CMRR)
ΔVicm × (1+ Rf/Rs)
CMRR  20 × Log
[dB]
VF8 - VF7
6. Power supply rejection ratio (PSRR)
ΔVcc × (1+ Rf/Rs)
PSRR  20 × Log
[dB]
VF10 - VF9
Test Circuit 2 Switch Condition
SW No.
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 SW11 SW12 SW13 SW14
Supply Current
OFF OFF OFF
ON
OFF
ON
OFF OFF OFF OFF OFF OFF OFF OFF
High Level Output Voltage
OFF OFF
ON
OFF OFF
ON
OFF OFF
OFF OFF OFF
ON
OFF
Low Level Output Voltage
OFF OFF
ON
OFF OFF
ON
OFF OFF OFF OFF OFF OFF
ON
OFF
Slew Rate
OFF OFF OFF
Gain Bandwidth Product
OFF
ON
OFF OFF
ON
Equivalent Input Noise Voltage
ON
OFF OFF OFF
ON
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
ON
OFF OFF OFF
20/26
ON
ON
ON
ON
OFF OFF OFF OFF
ON
OFF OFF
ON
ON
OFF OFF OFF OFF
ON
OFF OFF OFF OFF
ON
OFF OFF OFF
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
Input voltage
SW4
R2
SW5
VH
VCC
A
VL
-
SW1
SW2
SW6
RS
SW7
Output voltage
SW8
R1
t
Input wave
+
SW3
SW9
SW10
SW11
SW12
SW13
SW14
VEE
90% SR=ΔV/Δt
VH
C
A
~
VIN-
VIN+
~
RL
CL
V
~
ΔV
V
10%
VOUT
VL
Δt
t
Output wave
Fig.47 Test Circuit 2 (each Op-Amp)
Fig. 48 Slew Rate Input Waveform
Test Circuit 3 Channel Separation
VCC
VCC
R1//R2
R1//R2
OTHER
CH
VEE
R1
VIN
R2
VEE
V VOUT1
R1
R2
V
=0.5[Vrms]
CS=20×log
VOUT2
100×VOUT1
VOUT2
Fig. 49 Test circuit 3
(VCC=+15V, VEE=-15V, R1=1kΩ, R2=100kΩ)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
21/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
●Power Dissipation
Power dissipation(total loss) indicates the power that can be consumed by IC at Ta=25℃(normal temperature). IC is heated
when it consumed power, and the temperature of IC chip becomes higher than ambient temperature. The temperature that
can be accepted by IC chip depends on circuit configuration, manufacturing process, and consumable power is limited.
Power dissipation is determined by the temperature allowed in IC chip(maximum junction temperature) and thermal
resistance of package(heat dissipation capability). The maximum junction temperature is typically equal to the maximum
value in the storage temperature range. Heat generated by consumed power of IC radiates from the mold resin or lead
frame of the package. The parameter which indicates this heat dissipation capability(hardness of heat release)is called
thermal resistance, represented by the symbol θja℃/W.The temperature of IC inside the package can be estimated by this
thermal resistance. Fig.50(a) shows the model of thermal resistance of the package. Thermal resistance θja, ambient
temperature Ta, junction temperature Tj, and power dissipation Pd can be calculated by the equation below:
θja = (Tjmax-Ta) / Pd
℃/W
・・・・・ (Ⅰ)
Derating curve in Fig.50 (b) indicates power that can be consumed by IC with reference to ambient temperature. Power that
can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC begins to attenuate at
certain ambient temperature. This gradient is determined by thermal resistance θja. Thermal resistance θja depends on
chip size, power consumption, package, ambient temperature, package condition, wind velocity, etc even when the same of
package is used. Thermal reduction curve indicates a reference value measured at a specified condition. Fig.51(c),(d) show
a derating curve for an example of BA4558, BA4558R.
PowerLSIの
dissipation
of LSI [W]
消 費 電 力 [W]
Pd (max)
θja=(Tjmax-Ta)/Pd ℃/W
θja2 < θja1
P2
Ta [℃] Ta [℃]
周囲温度
Ambient
temperature
θ' ja2
P1
θ ja2
Tj ' (max) Tj (max)
θ' ja1
Chip surface temperature Tj [℃]
チップ 表面温度 Tj [℃]
Power dissipation P [W]
0
25
消費電力 P [W]
(a) Thermal resistance
50
θ ja1
75
100
125
150
] [℃]
囲 温 度 Ta [℃Ta
Ambient 周
temperature
(b) Derating curve
Fig. 50Thermal resistance and derating curve
1000
1000
*
POWER DISSIPATION [mW] .
POWER DISSIPATION [mW] .
BA4558RF( 11)
800
*
BA4558F( 11)
*
BA4558FJ( 12)
600
*
BA4558FV/FVT( 13)
*
BA4558FVM( 14)
400
200
*
BA4558RFJ( 12)
*
BA4558RFV/FVT( 13)
600
*
BA4558RFVM( 14)
400
200
0
0
0
25
50
75
100
AMBIENT TEMPERATURE [℃] .
125
0
(c)BA4558
(*11)
5.52
800
(*12)
5.4
(*13)
5
25
50
75
100
AMBIENT TEMPERATURE [℃ ] .
125
(d)BA4558R
(*14)
4.7
Unit
mW/℃
When using the unit above Ta=25℃, subtract the value above per degree℃. Permissible dissipation is the value.
Permissible dissipation is the value when FR4 glass epoxy board 70mm ×70mm ×1.6mm (cooper foil area below 3%) is mounted.
Fig. 51 Derating curve
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
22/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
Examples of circuit
○Voltage follower
Voltage gain is 0 dB.
This circuit controls output voltage (Vout) equal input
voltage (Vin), and keeps Vout with stable because of
high input impedance and low output impedance.
Vout is shown next formula.
Vout=Vin
VCC
Vout
Vin
VEE
Fig. 52 Voltage follower circuit
○Inverting amplifier
R2
For inverting amplifier, Vi(b) Derating curve voltage
gain decided R1 and R2, and phase reversed voltage
is outputted.
Vout is shown next formula.
Vout=-(R2/R1)・Vin
Input impedance is R1.
VCC
Vin
R1
Vout
R1//R2
VEE
Fig. 53 Inverting amplifier circuit
○Non-inverting amplifier
R1
R2
VCC
Vout
For non-inverting amplifier, Vin is amplified by voltage
gain decided R1 and R2, and phase is same with Vin.
Vout is shown next formula.
Vout=(1 + R2/R1)・Vin
This circuit realizes high input impedance because
Input impedance is operational amplifier’s input
Impedance.
Vin
VEE
Fig. 54 Non-inverting amplifier circuit
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
23/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
●Operational Notes
1) Processing of unused circuit
It is recommended to apply connection (see the Fig.55) and set the non inverting
input terminal at the potential within input common-mode voltage range (Vicm),
for any unused circuit.
2) Input voltage
Applying (VEE - 0.3) to (VEE + 36)V
(BA4558R) to the input terminal is possible without causing deterioration of the
electrical characteristics or destruction, irrespective of the supply voltage.
However, this does not ensure normal circuit operation. Please note that the
circuit operates normally only when the input voltage is within the common mode
input voltage range of the electric characteristics.
3) Maximum output voltage
Because the output voltage range becomes narrow as the output current
Increases, design the application with margin by considering changes in
electrical characteristics and temperature characteristics.
4) Short-circuit of output terminal
When output terminal and VCC or VEE terminal are shorted, excessive Output
current may flow under some conditions, and heating may destroy IC. It is
necessary to connect a resistor as shown in Fig.56, thereby protecting against
load shorting.
5) Power supply (split supply / single supply) in used
Op-amp operates when specified voltage is applied between VCC and VEE.
Therefore, the single supply Op-Amp can be used for double supply Op-Amp as well.
VCC
+
Connect
to Vicm Vicm
VEE
Fig. 55 The example of
application circuit for unused op-amp
VCC
+
protection
resistor
VEE
Fig. 56 The example of
output short protection
6) Power dissipation (Pd)
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating
conditions.
7) Short-circuit between pins and wrong mounting
Pay attention to the assembly direction of the ICs. Wrong mounting direction or shorts between terminals, GND, or other
components on the circuits, can damage the IC.
8) Use in strong electromagnetic field
Using the ICs in strong electromagnetic field can cause operation malfunction.
9) Radiation
This IC is not designed to be radiation-resistant.
10) IC Handling
When stress is applied to IC because of deflection or bend of board, the characteristics may fluctuate due to piezoelectric
(piezo) effect.
11) Inspection on set board
During testing, turn on or off the power before mounting or dismounting the board from the test Jig. Do not power up the
board without waiting for the output capacitors to discharge. The capacitors in the low output impedance terminal can
stress the device. Pay attention to the electro static voltages during IC handling, transportation, and storage.
12) Output capacitor
When VCC terminal is shorted to VEE (GND) potential and an electric charge has accumulated on the external capacitor,
connected to output terminal, accumulated charge may be discharged VCC terminal via the parasitic element within the
circuit or terminal protection element. The element in the circuit may be damaged (thermal destruction). When using this IC
for an application circuit where there is oscillation, output capacitor load does not occur, as when using this IC as a
voltage comparator. Set the capacitor connected to output terminal below 0.1μF in order to prevent damage to IC.
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
24/26
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
●Physical Dimensions Tape and Reel Information
SOP8
<Tape and Reel information>
5.0±0.2
(MAX 5.35 include BURR)
6
5
4.4±0.2
6.2±0.3
0.9±0.15
7
0.3MIN
8
+6°
4° −4°
1 2
3
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
4
0.595
1.5±0.1
+0.1
0.17 -0.05
S
S
0.11
0.1
1.27
Direction of feed
1pin
0.42±0.1
Reel
(Unit : mm)
∗ Order quantity needs to be multiple of the minimum quantity.
SSOP-B8
<Tape and Reel information>
3.0±0.2
(MAX 3.35 include BURR)
8
7
6
5
Tape
Embossed carrier tape
Quantity
2500pcs
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
0.3MIN
6.4 ± 0.3
4.4 ± 0.2
Direction
of feed
2
3
4
0.1
1.15±0.1
1
0.15±0.1
S
(0.52)
0.1 S
+0.06
0.22 −0.04
0.65
0.08
Direction of feed
1pin
M
Reel
(Unit : mm)
∗ Order quantity needs to be multiple of the minimum quantity.
MSOP8
<Tape and Reel information>
2.8±0.1
4.0±0.2
8 7 6 5
0.6±0.2
+6°
4° −4°
0.29±0.15
2.9±0.1
(MAX 3.25 include BURR)
Tape
Embossed carrier tape
Quantity
3000pcs
Direction
of feed
TR
The direction is the 1pin of product is at the upper right when you hold
( reel on the left hand and you pull out the tape on the right hand
)
1 2 3 4
1PIN MARK
1pin
+0.05
0.145 −0.03
0.475
+0.05
0.22 −0.04
0.08±0.05
0.75±0.05
0.9MAX
S
0.08 S
Direction of feed
0.65
Reel
(Unit : mm)
∗ Order quantity needs to be multiple of the minimum quantity.
TSSOP-B8
<Tape and Reel information>
3.0±0.1
(MAX 3.35 include BURR)
8
7
6
4±4
3000pcs
2
0.525
3
4
1PIN MARK
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
1.0±0.2
0.5 ± 0.15
6.4 ± 0.2
4.4 ± 0.1
+0.05
0.145 −0.03
S
0.1 ± 0.05
1.2MAX
Embossed carrier tape
Quantity
Direction
of feed
1
1.0 ± 0.05
Tape
5
0.08 S
+0.05
0.245 −0.04
0.08
M
1pin
0.65
(Unit : mm)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
Reel
25/26
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
BA4558xxx, BA4558Rxxx
Datasheet
SOP-J8
<Tape and Reel information>
4.9±0.2
(MAX 5.25 include BURR)
+6°
4° −4°
6
5
0.45MIN
7
3.9±0.2
6.0±0.3
8
1
2
3
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
4
0.545
0.2±0.1
0.175
1.375±0.1
S
1.27
0.42±0.1
0.1 S
Direction of feed
1pin
(Unit : mm)
Reel
∗ Order quantity needs to be multiple of the minimum quantity.
●Marking Diagrams
SOP8(TOP VIEW)
Part Number Marking
SSOP-B8(TOP VIEW)
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
MSOP8(TOP VIEW)
Part Number Marking
TSSOP-B8(TOP VIEW)
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
SOP-J8(TOP VIEW)
Part Number Marking
LOT Number
Product Name
Package Type
F
1PIN MARK
BA4558
BA4558R
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・00
26/26
SOP8
FV
SSOP-B8
FVT
TSSOP-B8
FVM
MSOP8
FJ
SOP-J8
F
SOP8
FV
Marking
4558
SSOP-B8
FVT
TSSOP-B8
FVM
MSOP8
FJ
SOP-J8
4558R
TSZ02201-0RAR1G200010-1-2
4.SEP.2012 Rev.003
Datasheet
Notice
●General Precaution
1) Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2) All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
●Precaution on using ROHM Products
1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
2)
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3)
Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4)
The Products are not subject to radiation-proof design.
5)
Please verify and confirm characteristics of the final or mounted products in using the Products.
6)
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7)
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8)
Confirm that operation temperature is within the specified range described in the product specification.
9)
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.
Datasheet
●Precaution for Mounting / Circuit board design
1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2)
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
●Precautions Regarding Application Examples and External Circuits
1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2)
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
●Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
●Precaution for Storage / Transportation
1) Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2)
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3)
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4)
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
●Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
●Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
●Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
●Precaution Regarding Intellectual Property Rights
1) All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2)
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.
Datasheet
●Other Precaution
1) The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
2)
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
3)
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
4)
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
5)
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.
Similar pages