ON BC859CLT1 General purpose transistor Datasheet

BC856ALT1 Series
Preferred Devices
General Purpose
Transistors
PNP Silicon
Features
http://onsemi.com
• Pb−Free Packages are Available
COLLECTOR
3
1
BASE
MAXIMUM RATINGS (TA = 25°C unless otherwise noted)
Symbol
Value
Unit
Collector-Emitter Voltage
VCEO
−65
−45
−30
V
Collector-Base Voltage
VCBO
−80
−50
−30
V
VEBO
−5.0
V
IC
−100
mAdc
Rating
BC856
BC857
BC858, BC859
BC856
BC857
BC858, BC859
Emitter−Base Voltage
Collector Current − Continuous
2
EMITTER
3
SOT−23
CASE 318
STYLE 6
1
Maximum ratings are those values beyond which device damage can occur.
Maximum ratings applied to the device are individual stress limit values (not
normal operating conditions) and are not valid simultaneously. If these limits
are exceeded, device functional operation is not implied, damage may occur
and reliability may be affected.
2
MARKING DIAGRAM
3
THERMAL CHARACTERISTICS
Characteristic
Total Device Dissipation FR− 5 Board,
(Note 1) TA = 25°C
Derate above 25°C
Thermal Resistance,
Junction−to−Ambient
Total Device Dissipation Alumina
Substrate, (Note 2) TA = 25°C
Derate above 25°C
Thermal Resistance,
Junction−to−Ambient
Junction and Storage Temperature
Symbol
Unit
225
1.8
mW
mW/°C
556
°C/W
300
2.4
mW
mW/°C
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 6 of this data sheet.
PD
RJA
xxM
Max
1
2
xx = Device Code
M = Date Code
PD
RJA
417
°C/W
TJ, Tstg
−55 to
+150
°C
Preferred devices are recommended choices for future use
and best overall value.
1. FR−5 = 1.0 x 0.75 x 0.062 in.
2. Alumina = 0.4 x 0.3 x 0.024 in 99.5% alumina.
 Semiconductor Components Industries, LLC, 2004
June, 2004 − Rev. 8
1
Publication Order Number:
BC856ALT1/D
BC856ALT1 Series
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max
Unit
OFF CHARACTERISTICS
Collector −Emitter Breakdown Voltage
(IC = −10 mA)
BC856 Series
BC857 Series
BC858, BC859 Series
V(BR)CEO
−65
−45
−30
−
−
−
−
−
−
V
Collector −Emitter Breakdown Voltage
(IC = −10 A, VEB = 0)
BC856 Series
BC857A, BC857B Only
BC858, BC859 Series
V(BR)CES
−80
−50
−30
−
−
−
−
−
−
V
Collector −Base Breakdown Voltage
(IC = −10 A)
BC856 Series
BC857 Series
BC858, BC859 Series
V(BR)CBO
−80
−50
−30
−
−
−
−
−
−
V
Emitter −Base Breakdown Voltage
(IE = −1.0 A)
BC856 Series
BC857 Series
BC858, BC859 Series
V(BR)EBO
−5.0
−5.0
−5.0
−
−
−
−
−
−
V
ICBO
−
−
−
−
−15
−4.0
nA
A
hFE
−
−
−
90
150
270
−
−
−
−
125
220
420
180
290
520
250
475
800
−
−
−
−
−0.3
−0.65
−
−
−0.7
−0.9
−
−
−0.6
−
−
−
−0.75
−0.82
fT
100
−
−
MHz
Output Capacitance
(VCB = −10 V, f = 1.0 MHz)
Cob
−
−
4.5
pF
Noise Figure
(IC = −0.2 mA, VCE = −5.0 Vdc, RS = 2.0 k, f = 1.0 kHz, BW = 200 Hz)
BC856, BC857, BC858 Series
BC859 Series
NF
Collector Cutoff Current (VCB = −30 V)
Collector Cutoff Current (VCB = −30 V, TA = 150°C)
ON CHARACTERISTICS
DC Current Gain
(IC = −10 A, VCE = −5.0 V)
(IC = −2.0 mA, VCE = −5.0 V)
BC856A, BC857A, BC858A
BC856B, BC857B, BC858B
BC857C, BC858C
BC856A, BC857A, BC858A
BC856B, BC857B, BC858B, BC859B
BC857C, BC858C, BC859C
Collector −Emitter Saturation Voltage
(IC = −10 mA, IB = −0.5 mA)
(IC = −100 mA, IB = −5.0 mA)
VCE(sat)
Base −Emitter Saturation Voltage
(IC = −10 mA, IB = −0.5 mA)
(IC = −100 mA, IB = −5.0 mA)
VBE(sat)
Base −Emitter On Voltage
(IC = −2.0 mA, VCE = −5.0 V)
(IC = −10 mA, VCE = −5.0 V)
VBE(on)
V
V
V
SMALL−SIGNAL CHARACTERISTICS
Current −Gain − Bandwidth Product
(IC = −10 mA, VCE = −5.0 Vdc, f = 100 MHz)
http://onsemi.com
2
dB
−
−
−
−
10
4.0
BC856ALT1 Series
BC857/BC858/BC859
−1.0
1.5
TA = 25°C
−0.9
VCE = −10 V
TA = 25°C
VBE(sat) @ IC/IB = 10
−0.8
V, VOLTAGE (VOLTS)
hFE , NORMALIZED DC CURRENT GAIN
2.0
1.0
0.7
0.5
−0.7
VBE(on) @ VCE = −10 V
−0.6
−0.5
−0.4
−0.3
−0.2
0.3
VCE(sat) @ IC/IB = 10
−0.1
0.2
−0.2
−0.5 −1.0 −2.0
−5.0 −10 −20
−50
IC, COLLECTOR CURRENT (mAdc)
0
−0.1 −0.2
−100 −200
1.0
−2.0
TA = 25°C
−1.6
−1.2
−0.8
IC =
−10 mA
IC = −50 mA
IC = −200 mA
IC = −100 mA
IC = −20 mA
−0.4
0
−0.02
−55°C to +125°C
1.2
1.6
2.0
2.4
2.8
−10 −20
−0.1
−1.0
IB, BASE CURRENT (mA)
−0.2
10
Cib
7.0
TA = 25°C
5.0
Cob
3.0
2.0
1.0
−0.4 −0.6
−1.0
−2.0
−4.0 −6.0
−10
−10
−1.0
IC, COLLECTOR CURRENT (mA)
−100
Figure 4. Base−Emitter Temperature Coefficient
f,
T CURRENT−GAIN − BANDWIDTH PRODUCT (MHz)
Figure 3. Collector Saturation Region
C, CAPACITANCE (pF)
−100
−50
Figure 2. “Saturation” and “On” Voltages
θVB , TEMPERATURE COEFFICIENT (mV/ °C)
VCE , COLLECTOR−EMITTER VOLTAGE (V)
Figure 1. Normalized DC Current Gain
−0.5 −1.0 −2.0
−5.0 −10 −20
IC, COLLECTOR CURRENT (mAdc)
−20 −30 −40
400
300
200
150
VCE = −10 V
TA = 25°C
100
80
60
40
30
20
−0.5
−1.0
−2.0 −3.0
−5.0
−10
−20
−30
−50
VR, REVERSE VOLTAGE (VOLTS)
IC, COLLECTOR CURRENT (mAdc)
Figure 5. Capacitances
Figure 6. Current−Gain − Bandwidth Product
http://onsemi.com
3
BC856ALT1 Series
BC856
TJ = 25°C
VCE = −5.0 V
TA = 25°C
−0.8
V, VOLTAGE (VOLTS)
hFE , DC CURRENT GAIN (NORMALIZED)
−1.0
2.0
1.0
0.5
VBE(sat) @ IC/IB = 10
−0.6
VBE @ VCE = −5.0 V
−0.4
−0.2
0.2
VCE(sat) @ IC/IB = 10
0
−0.2
−1.0 −2.0 −5.0 −10 −20 −50 −100 −200
IC, COLLECTOR CURRENT (mA)
−0.1 −0.2
−0.5
−50 −100 −200
−5.0 −10 −20
−1.0 −2.0
IC, COLLECTOR CURRENT (mA)
Figure 8. “On” Voltage
−2.0
−1.6
−1.2
IC =
−10 mA
−20 mA
−50 mA
−100 mA −200 mA
−0.8
−0.4
TJ = 25°C
0
−0.02
−0.05 −0.1 −0.2
−0.5 −1.0 −2.0
IB, BASE CURRENT (mA)
−5.0
−10
θVB, TEMPERATURE COEFFICIENT (mV/ °C)
VCE , COLLECTOR−EMITTER VOLTAGE (VOLTS)
Figure 7. DC Current Gain
−20
−1.0
−1.4
−1.8
−2.6
−3.0
−0.2
f,
T CURRENT−GAIN − BANDWIDTH PRODUCT
C, CAPACITANCE (pF)
TJ = 25°C
Cib
10
8.0
Cob
4.0
2.0
−0.1 −0.2
−0.5
−1.0 −2.0
−5.0 −10 −20
VR, REVERSE VOLTAGE (VOLTS)
−0.5 −1.0
−50
−2.0
−5.0 −10 −20
IC, COLLECTOR CURRENT (mA)
−100 −200
Figure 10. Base−Emitter Temperature Coefficient
40
6.0
−55°C to 125°C
−2.2
Figure 9. Collector Saturation Region
20
VB for VBE
VCE = −5.0 V
500
200
100
50
20
−100
−1.0
−10
IC, COLLECTOR CURRENT (mA)
−50 −100
Figure 11. Capacitance
Figure 12. Current−Gain − Bandwidth Product
http://onsemi.com
4
r(t), TRANSIENT THERMAL
RESISTANCE (NORMALIZED)
BC856ALT1 Series
1.0
0.7
0.5
0.3
D = 0.5
0.2
0.2
0.1
0.05
SINGLE PULSE
0.1
0.07
0.05
SINGLE PULSE
t1
t2
0.03
DUTY CYCLE, D = t1/t2
0.02
0.01
0.1
ZJC(t) = r(t) RJC
RJC = 83.3°C/W MAX
ZJA(t) = r(t) RJA
RJA = 200°C/W MAX
D CURVES APPLY FOR POWER
PULSE TRAIN SHOWN
READ TIME AT t1
TJ(pk) − TC = P(pk) RJC(t)
P(pk)
0.2
0.5
1.0
2.0
10
5.0
20
t, TIME (ms)
50
100
200
500
1.0k
2.0k
5.0k 10k
Figure 13. Thermal Response
The safe operating area curves indicate IC−VCE limits of
the transistor that must be observed for reliable operation.
Collector load lines for specific circuits must fall below the
limits indicated by the applicable curve.
The data of Figure 14 is based upon TJ(pk) = 150°C; TC or
TA is variable depending upon conditions. Pulse curves are
valid for duty cycles to 10% provided TJ(pk) ≤ 150°C. TJ(pk)
may be calculated from the data in Figure 13. At high case or
ambient temperatures, thermal limitations will reduce the
power that can be handled to values less than the limitations
imposed by the secondary breakdown.
−200
IC, COLLECTOR CURRENT (mA)
1s
3 ms
−100
−50
−10
−5.0
−2.0
−1.0
TA = 25°C
TJ = 25°C
BC558, BC559
BC557
BC556
BONDING WIRE LIMIT
THERMAL LIMIT
SECOND BREAKDOWN LIMIT
−5.0
−10
−30 −45 −65 −100
VCE, COLLECTOR−EMITTER VOLTAGE (V)
Figure 14. Active Region Safe Operating Area
http://onsemi.com
5
BC856ALT1 Series
ORDERING INFORMATION
Marking
Package
Shipping†
BC856ALT1
3A
SOT−23
3,000 / Tape & Reel
BC856ALT3
3A
SOT−23
10,000 / Tape & Reel
BC856BLT1
3B
SOT−23
BC856BLT1G
3B
SOT−23
(Pb−Free)
3,000 / Tape & Reel
BC856BLT3
3B
SOT−23
10,000 / Tape & Reel
BC857ALT1
3E
SOT−23
3,000 / Tape & Reel
BC857BLT1
3F
SOT−23
3,000 / Tape & Reel
BC857BLT3
3F
SOT−23
BC857BLT3G
3F
SOT−23
(Pb−Free)
10,000 / Tape & Reel
BC857CLT1
3G
SOT−23
3,000 / Tape & Reel
BC857CLT1G
3G
SOT−23
(Pb−Free)
3,000 / Tape & Reel
BC858ALT1
3J
SOT−23
BC858ALT1G
3J
SOT−23
(Pb−Free)
BC858BLT1
3K
SOT−23
BC858BLT1G
3K
SOT−23
(Pb−Free)
3,000 / Tape & Reel
BC858BLT3
3L
SOT−23
10,000 / Tape & Reel
BC858CLT1
3L
SOT−23
BC858CLT1G
3L
SOT−23
(Pb−Free)
BC858CLT3
3L
SOT−23
BC858CLT3G
3L
SOT−23
(Pb−Free)
10,000 / Tape & Reel
BC859BLT1
4B
SOT−23
3,000 / Tape & Reel
BC859BLT3
4B
SOT−23
10,000 / Tape & Reel
BC859CLT1
4C
SOT−23
3,000 / Tape & Reel
BC859CLT3
4C
SOT−23
10,000 / Tape & Reel
Device
3,000 / Tape & Reel
3,000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
6
BC856ALT1 Series
PACKAGE DIMENSIONS
SOT−23 (TO−236)
CASE 318−09
ISSUE AI
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. MAXIUMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM
THICKNESS OF BASE MATERIAL.
4. 318−01, −02, AND −06 OBSOLETE, NEW STANDARD 318−09.
A
L
3
1
V
B
2
S
DIM
A
B
C
D
G
H
J
K
L
S
V
G
C
D
H
J
K
INCHES
MIN
MAX
0.1102
0.1197
0.0472 0.0551
0.0385 0.0498
0.0140 0.0200
0.0670 0.0826
0.0040 0.0098
0.0034 0.0070
0.0180 0.0236
0.0350 0.0401
0.0830 0.0984
0.0177 0.0236
STYLE 6:
PIN 1. BASE
2. EMITTER
3. COLLECTOR
SOLDERING FOOTPRINT*
0.95
0.037
0.95
0.037
2.0
0.079
0.9
0.035
0.8
0.031
SCALE 10:1
mm inches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
7
MILLIMETERS
MIN
MAX
2.80
3.04
1.20
1.40
0.99
1.26
0.36
0.50
1.70
2.10
0.10
0.25
0.085
0.177
0.45
0.60
0.89
1.02
2.10
2.50
0.45
0.60
BC856ALT1 Series
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
8
For additional information, please contact your
local Sales Representative.
BC856ALT1/D
Similar pages