Rohm BD3533F Termination regulators for ddr-sdram Datasheet

TECHNICAL NOTE
High-performance Regulator IC Series for PCs
Termination Regulators
for DDR-SDRAMs
BD3533F/FVM/EKN(1A),BD3531F(1.5A),BD3532F/EFV/KN(3A)
Description
BD3533/31/32 is a termination regulator compatible with JEDEC DDR-SDRAM, which functions as a linear power supply
incorporating an N-channel MOSFET and provides a sink/source current capability up to 1A, 1.5A, and 3A respectively. A
built-in high-speed OP-AMP specially designed offers an excellent transient response. Requires 3.3 volts or 5.0 volts as a
bias power supply to drive the N-channel MOSFET. Has an independent reference voltage input pin (VDDQ) and an
independent feedback pin (VTTS) to maintain the accuracy in voltage required by JEDEC, and offers an excellent output
voltage accuracy and load regulation. Also has a reference power supply output pin (VREF) for DDR-SDRAM or a
memory controller. When EN pin turns to “Low”, VTT output becomes “Hi-Z” while VREF output is kept unchanged,
compatible with “Self Refresh” state of DDR-SDRAM.
Features
1) Incorporates a push-pull power supply for termination (VTT)
2) Incorporates a reference voltage circuit (VREF)
3) Incorporates an enabler
4) Incorporates an undervoltage lockout (UVLO)
5). Employs SOP8 package
6) Employs MSOP8 package
7) Employs HQFN20V package
8) Employs HTSSOP-B20 package
9) Employs VQFN28V package
10) Incorporates a thermal shutdown protector (TSD)
11) Operates with input voltage from 2.7 to 5.5 volts
12) Compatible with Dual Channel (DDR-II)
Use
Power supply for DDR I/II - SDRAM
●Line up
Parameter
Output Current
Vcc Range
Soft Start Function
Temperature
Package
BD3533F/FVM/EKN
±1.0A
2.7V~5.5V
○
-20~100℃
SOP8/MSOP8/HQFN20V
BD3531F
±1.5A
4.5V~5.5V
×
-10~100℃
SOP8
BD3532F/EFV/KN
±3A
4.3~5.5V
○
-40~100℃
SOP8/HTSSOP-B20/VQFN28
Oct. 2008
●ABSOLUTE MAXIMUM RATINGS
◎BD3533F/FVM/EKN
Parameter
Symbol
BD3533F
BD3533FVM
*1*2
BD3533EKN
V
VCC
7
Enable Input Voltage
VEN
7 *1*2
7 *1*2
7 *1*2
V
*1*2
*1*2
*1*2
V
7 *1*2
V
VTT_IN
7
VDDQ Reference Voltage
VDDQ
7 *1*2
7
7 *1*2
7
Unit
*1*2
Input Voltage
Termination Input Voltage
7
*1*2
7
Output Current
ITT
3
1
3
A
Power Dissipation1
Pd1
560 *3
437.5 *5
500 *6
mW
Power Dissipation2
Pd2
690 *4
-
750 *7
mW
Power Dissipation3
Pd3
-
-
1750 *8
mW
*9
mW
Power Dissipation4
Pd4
-
-
Operating Temperature Range
Topr
-20~+100
-20~+100
-20~+100
℃
Storage Temperature Range
Tstg
-55~+150
-55~+150
-55~+150
℃
Tjmax
+150
+150
+150
℃
Maximum Junction Temperature
2000
*1 Should not exceed Pd.
*2 Instantaneous surge voltage, back electromotive force and voltage under less than 10% duty cycle.
*3 Reduced by 4.48mW for each increase in Ta of 1℃ over 25℃(With no heat sink).
*4 Reduced by 5.52mW for each increase in Ta of 1℃ over 25℃(When mounted on a board 70mm×70mm×1.6mm Glass-epoxyPCB).
*5 Reduced by 3.5mW for each increase in Ta of 1℃ over 25℃(With no heat sink).
*6 Ta≧25℃(no heat sink)4mW/℃ increase.
*7 Ta≧25℃(when mounted on 70mm x 70mm x 1.6mm Glass-epoxy PCB which does not have copper on the back side).
*8 Ta≧25℃(when mounted on 70mm x 70mm x 1.6mm Glass-epoxy PCB which has 1 layer ( 60mm x 60mm ) of copper on the back side)14mW/℃ increase.
*9 Ta≧25℃(When mounted on board 70mm x 70mm x 1.6mm Glass-epoxy PCB which has 2 layers ( 60mm x 60mm ) of copper on the back side )16mW/℃
increase.
◎BD3531F
Parameter
Symbol
Limit
1
Unit
Input Voltage
VCC
7*
V
EN Input Voltage
VEN
7 *1
V
1
Termination Input Voltage
VTT_IN
7*
V
VDDQ Reference Voltage
VDDQ
7 *1
V
ITT
3
Output Current
A
2
Power Dissipation1
Pd1
560 *
mW
Power Dissipation2
Pd2
690 *3
mW
Operating Temperature Range
Topr
-10~
℃
Storage Temperature Range
Tstg
-55~
℃
Tjmax
+150
℃
Maximum Junction Temperature
*1 Should not exceed Pd.
*2 Reduced by 4.48mW for each increase in Ta of 1℃ over 25℃(With no heat sink).
*3 Reduced by 5.52mW for each increase in Ta of 1℃ over 25℃(When mounted on a board 70mm×70mm×1.6mm Glass-epoxyPCB).
◎BD3532F/EFV/KN
Parameter
Input Voltage
Enable Input Voltage
Symbol
BD3532F
BD3532EFV
BD3532KN
Unit
VCC
7 *1
7 *1
7 *1
V
VEN
1
1
1
V
1
7*
1
7*
7*
1
Termination Input Voltage
VTT_IN
7*
7*
7*
V
VDDQ Reference Voltage
VDDQ
7 *1
7 *1
7 *1
V
Output Current
ITT
3
3
3
A
Power Dissipation1
Pd1
560 *2
-
460 *5
mW
Power Dissipation2
Pd2
690 *3
1000 *
725 *6
mW
Operating Temperature Range
Topr
-40~+100
-40~+100
-40~+100
℃
Tstg
-55~+150
-55~+150
-55~+150
℃
Tjmax
+150
+150
+150
℃
Storage Temperature Range
Maximum Junction Temperature
4
*1 Should not exceed Pd.
*2 Reduced by 4.48mW for each increase in Ta of 1℃ over 25℃(With no heat sink).
*3 Reduced by 5.52mW for each increase in Ta of 1℃ over 25℃(When mounted on a board 70mm×70mm×1.6mm Glass-epoxyPCB).
*4 Reduced by 8.0mW for each increase in Ta of 1℃ over 25℃(When mounted on a board 70mm×70mm×1.6mm Glass-epoxyPCB).
*5 Reduced by 3.68mW for each increase in Ta of 1℃ over 25℃(With no heat sink).
*6 Reduced by 5.80mW for each increase in Ta of 1℃ over 25℃(When mounted on a board 70mm×70mm×1.6mm Glass-epoxyPCB).
2/16
●RECOMMENDED OPERATING CONDITIONS
◎BD3533F/FVM/EKN(Ta=25℃)
Parameter
Input Voltage
Symbol
MIN
MAX
Unit
VCC
2.7
5.5
V
Termination Input Voltage
VTT_IN
1.0
5.5
V
VDDQ Reference Voltage
VDDQ
1.0
2.75
V
VEN
-0.3
5.5
V
Symbol
MIN
MAX
Unit
Enable Input Voltage
◎BD3531F(Ta=25℃)
Parameter
Input Voltage
Termination Input Voltage
EN Input Voltage
VCC
4.5
5.5
V
VTT_IN
1.0
5.5
V
VEN
-0.3
5.5
V
Symbol
MIN
MAX
Unit
VCC
4.3
5.5
V
VTT_IN
1.0
5.5
V
VEN
-0.3
5.5
V
◎BD3532F/EFV/KN(Ta=25℃)
Parameter
Input Voltage
Termination Input Voltage
EN Input Voltage
★ No radiation-resistant design is adopted for the present product.
●ELECTRICAL CHARACTERISTICS
◎BD3533F/FVM/EKN
ELECTRICAL CHARACTERISTICS(unless otherwise noted, Ta=25℃ VCC=3.3V VEN=3V VDDQ=1.8V VTT_IN=1.8V)
Parameter
Symbol
Standard Value
MIN
TYP
MAX
Unit
Condition
Standby Current
IST
-
0.8
1.6
mA
VEN=0V
Bias Current
ICC
-
2
4
mA
VEN=3V
High Level Enable Input Voltage
VENHIGH
2.3
-
5.5
V
Low Level Enable Input Voltage
VENLOW
-0.3
-
0.8
V
IEN
-
7
10
uA
Termination Output Voltage 1
VTT1
VREF
-30m
VREF
VREF
+30m
V
Termination Output Voltage 2
VTT2
VREF
-30m
VREF
VREF
+30m
V
Source Current
ITT+
1.0
-
-
A
[Enable]
Enable Pin Input Current
VEN=3V
[Termination]
Sink Current
Load Regulation
Line Regulation
ITT-
-
-
-1.0
A
⊿VTT
-
-
50
mV
Reg.l
-
20
40
mV
Upper Side ON Resistance 1
HRON1
-
0.45
0.9
Ω
Lower Side ON Resistance 1
LRON1
-
0.45
0.9
Ω
Upper Side ON Resistance 2
HRON2
-
0.4
0.8
Ω
Lower Side ON Resistance 2
LRON2
-
0.4
0.8
Ω
*7 Design Guarantee
3/16
ITT=-1.0A to 1.0A
*7
Ta=0℃ to 100℃
VCC=5V, VDDQ=2.5V
VTT_IN=2.5V
ITT=-1.0A to 1.0A
*7
Ta=0℃ to 100℃
ITT=-1.0A to 1.0A
VCC=5V, VDDQ=2.5V
VTT_IN=2.5V
VCC=5V, VDDQ=2.5V
VTT_IN=2.5V
●ELECTRICAL CHARACTERISTICS
◎BD3533F/FVM/EKN
ELECTRICAL CHARACTERISTICS(unless otherwise noted, Ta=25℃ VCC=3.3V VEN=3V VDDQ=1.8V VTT_IN=1.8V)
Parameter
Standard Value
Symbol
MIN
TYP
70
100
Unit
MAX
Condition
[Input of Reference Voltage]
Input Impedance
ZVDDQ
Output Voltage1
VREF1
Output Voltage2
VREF2
Output Voltage3
VREF3
Output Voltage4
VREF4
1/2×VDDQ
-18m
1/2×VDDQ
-40m
1/2×VDDQ
-25m
1/2×VDDQ
-40m
130
1/2×VDDQ
1/2×VDDQ
1/2×VDDQ
1/2×VDDQ
kΩ
1/2×VDDQ
+18m
1/2×VDDQ
+40m
1/2×VDDQ
+25m
IREF=-5mA to 5mA
*7
Ta=0℃ to 100℃
IREF=-10mA to 10mA
*7
Ta=0℃ to 100℃
V
V
VCC=5V, VDDQ=VTT_IN=2.5V
V
IREF=-5mA to 5mA
Ta=0℃ to 100℃*7
1/2×VDDQ
+40m
VCC=5V, VDDQ=VTT_IN=2.5V
V
IREF=-10mA to 10mA
Ta=0℃ to 100℃*7
[Reference voltage]
Source Current
IREF+
20
-
-
mA
Sink Current
IREF-
-
-
-20
mA
UVLO OFF Voltage
VUVLO
2.40
2.55
2.70
V
Hysteresis Voltage
⊿VUVLO
100
160
220
mV
[UVLO]
VCC : sweep up
VCC : sweep down
*7 Design Guarantee
◎BD3531F
ELECTRICAL CHARACTERISTICS(unless otherwise noted, Ta=25℃ VCC=5V VEN=3V VDDQ=2.5V VTT_IN=2.5V)
Parameter
Symbol
Standard Value
MIN
TYP
MAX
Unit
Condition
Standby Current
IST
-
0.8
1.6
mA
VEN=0V
Bias Current
ICC
-
2
4
mA
VENHI
2
-
5.5
V
VENLOW
-0.3
-
0.8
V
IEN
-
7
10
uA
VEN=3V
Termination Output Voltage
VTT
VREF
-30mV
VREF
VREF
+30mV
V
Io=-1.5A to 1.5A
8
Ta=0℃ to 100℃ *
Source Current
ITT+
1.5
-
-
A
Sink Current
ITT-
-
-
-1.5
A
Load Regulation
⊿VTT
-
-
40
mV
Io=-1.5A to 1.5A
Line Regulation
Reg.l
-
20
40
mV
VCC=4.5V to 5.5V
Upper Side ON Resistance
HRON
-
0.4
0.8
Ω
Lower Side ON Resistance
LRON
-
0.4
0.8
Ω
ZVDDQ
-
100
-
kΩ
Output Voltage1
VREF1
1/2×VDDQ-30m
1/2×VDDQ
Output Voltage2
VREF2
Source Current
IREF+
10
20
-
mA
Sink Current
IREF-
-
-20
-10
mA
UVLO OFF Voltage
VUVLO
4.2
4.35
4.5
V
Hysteresis Voltage
⊿VUVLO
100
160
220
mV
[Enable]
Hi Level Enable Input Voltage
Low Level Enable Input Voltage
Enable Pin Input Current
[Termination]
[Input of Reference Voltage]
Input Impedance
[Reference voltage]
1/2×VDDQ
-40m
1/2×VDDQ
1/2×VDDQ+30m
1/2×VDDQ
+40m
V
IREF=0mA
V
IREF=-10mA to 10mA
Ta=0℃ to 100℃ *8
[UVLO]
*8 Design Guarantee
4/16
VCC : Sweep up
VCC : Sweep down
◎BD3532F/EFV/KN
ELECTRICAL CHARACTERISTICS(unless otherwise noted, Ta=25℃ VCC=5V VEN=3V VDDQ=2.5V VTT_IN=2.5V)
Parameter
Symbol
Standard Value
MIN
TYP
MAX
Unit
Condition
Standby Current
IST
-
0.8
1.6
mA
VEN=0V
Bias Current
ICC
-
2
4
mA
VENHI
2.3
-
5.5
V
VENLOW
-0.3
-
0.8
V
IEN
-
7
10
uA
VEN=3V
Termination Output Voltage
VTT
VREF
-30mV
VREF
VREF
+30mV
V
Io=-3A to 3A
Ta=0℃ to 100℃ *9
Source Current
ITT+
3
-
-
A
Sink Current
ITT-
-
-
-3
A
Load Regulation
⊿VTT
-
-
40
mV
Io=-3A to 3A
Line Regulation
Reg.l
-
20
40
mV
VCC=4.3V to 5.5V
Upper Side ON Resistance
HRON
-
0.2
0.4
Ω
Lower Side ON Resistance
LRON
-
0.2
0.4
Ω
Input Impedance
ZVDDQ
70
100
130
kΩ
Output Voltage1
VREF1
Output Voltage2
VREF2
Output Voltage1’
VREF1’
Output Voltage2’
VREF2’
Source Current1
IREF1+
20
-
-
mA
Sink Current1
IREF1-
-
-
-20
mA
Source Current2
IREF2+
20
-
-
mA
VDDQ=VTT_IN1=VTT_IN2=1.8V
Sink Current2
IREF2-
-
-
-20
mA
VDDQ=VTT_IN1=VTT_IN2=1.8V
UVLO OFF Voltage
VUVLO
4.0
4.15
4.3
V
Hysteresis Voltage
⊿VUVLO
100
160
220
mV
[Enable]
Hi Level Enable Input
Voltage
Low Level Enable Input
Voltage
Enable Pin Input Current
VCC=4.3V to 5.5V
9
Ta=0℃ to 100℃ *
VCC=4.3V to 5.5V
9
Ta=0℃ to 100℃ *
[Termination]
[Input of Reference Voltage]
1/2×VDDQ
1/2×VDDQ
1/2×VDDQ
-30mV
+30mV
1/2×VDDQ
1/2×VDDQ
1/2×VDDQ
-40mV
+40mV
1/2×VDDQ
1/2×VDDQ
1/2×VDDQ
-30mV
+30mV
1/2×VDDQ
1/2×VDDQ
1/2×VDDQ
-40mV
+40mV
V
V
V
V
IREF=0mA
IREF=-10mA to 10mA
Ta=0℃ to 100℃ *9
VDDQ=VTT_IN1=VTT_IN2=1.8V
IREF=0mA
VDDQ=VTT_IN1=VTT_IN2=1.8V
IREF=-10mA to 10mA
9
Ta=0℃ to 100℃ *
[UVLO]
*9 Design Guarantee
5/16
VCC : sweep up
VCC : sweep down
●Reference Data
VTT(10mV/Div)
ITT(1A/Div)
VTT(10mV/Div)
VTT(20mV/Div)
ITT(1A/Div)
ITT(1A/Div)
10μsec/Div
Fig.1 DDRⅠ(-1A→1A) BD3531
10μsec/Div
Fig.2 DDRⅠ(-1A→1A) BD3532
10μsec/Div
Fig.3 DDRⅠ(-1A→1A) BD3533
VTT(20mV/Div)
VTT(10mV/Div)
VTT(10mV/Div)
ITT(1A/Div)
ITT(1A/Div)
10μsec/Div
Fig.4 DDRⅠ(1A→-1A) BD3531
10μsec/Div
Fig.5 DDRⅠ(1A→-1A) BD3532
ITT(1A/Div)
10μsec/Div
Fig.6 DDRⅠ(1A→-1A) BD3533
VTT(10mV/Div)
VTT(10mV/Div)
VTT(20mV/Div)
ITT(1A/Div)
ITT(1A/Div)
ITT(1A/Div)
10μsec/Div
Fig.7 DDRⅡ(-1A→1A) BD3531
VTT(10mV/Div)
ITT(1A/Div)
10μsec/Div
Fig.8 DDRⅡ(-1A→1A) BD3532
Fig.9 DDRⅡ(-1A→1A) BD3533
VTT(10mV/Div)
VTT(20mV/Div)
ITT(1A/Div)
ITT(1A/Div)
10μsec/Div
Fig.10 DDRⅡ(1A→-1A) BD3531
10μsec/Div
10μsec/Div
Fig.11 DDRⅡ(1A→-1A) BD3532
6/16
10μsec/Div
Fig.12 DDRⅡ(1A→-1A) BD3533
1.256
0.901
1.251
1.254
1.25
0.9
VTT(V)
VREF(V)
VREF(V)
1.258
0.902
1.252
0.899
1.252
1.250
1.248
1.249
0.898
1.248
-10
-5
0
IREF(mA)
5
10
Fig.13 IREF-VREF (DDR-Ⅰ)
1.246
0.897
-10
1.244
-5
0
IREF(mA)
5
10
Fig.14 IREF-VREF (DDR-Ⅱ)
-2
-1
0
ITT(A)
1
Fig.15 ITT-VTT (DDR-Ⅰ)
0.91
0.912
0.91
0.910
0.90
0.908
VTT(V)
VTT(V)
0.90
0.906
VCC
VCC
EN
EN
VDDQ
VTT IN
VDDQ
VTT IN
VTT
VTT
0.90
0.904
0.90
0.902
0.90
0.900
0.89
0.898
0.896
0.89
-2
-1
0
ITT(A)
1
Fig.16 ITT-VTT (DDR-Ⅱ)
2
Fig.17 Input Sequence 1
VTT_IN
VCC
EN
VDDQ
VTT IN
VTT
VREF
ITT_IN
(1A/div)
VTT
Fig.19 Input Sequence 3
Fig.20 Start up Wave Form
7/16
Fig.18 Input Sequence 2
2
●BLOCK DIAGRAM
◎BD3533F/FVM/EKN
VCC
VCC
VCC
UVLO
Reference
Block
VTT_IN
VTT_IN
VDDQ
VCC
Thermal
VTT_IN
VDDQ
VCC
SOFT
TSD
UVLO EN
UVLO
VTT
TSD
VCC EN
UVLO
VTT
TSD
EN
UVLO
TSD
VTTS
VREF
Protection
Enable
EN
VTT
EN
½×
VDDQ
VREFS
DGND
PGND
◎BD3531F
VDDQ
VCC
VCC
Reference
Block
Enable
VTT_IN
VCC
VCC
UVLO
TSD
VCC EN
UVLO
50kΩ
UVLO
50kΩ
Thermal
VTT_IN
VDDQ
VCC
VTT
TSD
EN
UVLO
TSD
Protection
VTT
VTTS
VREF
EN
½×
VDDQ
GND
◎BD3532F/FVM/EKN
VDDQ
VCC
50kΩ
UVLO
Reference
Block
VTT_IN
VCC
VCC
50kΩ
Thermal
VTT_IN
VDDQ
VCC
VCC
SOFT
UVLO UVLO
TSD
EN
UVLO
TSD
Protection
Enable
EN
TSD
VCC EN
UVLO
VTT
VTTS
VREF
EN
GND
8/16
VTT
½×
VDDQ
◎BD3533F/BD3533FVM/BD3531F/BD3532F
●PIN CONFIGRATION
GND 1
●PIN FUNCTION
PIN No.
PIN NAME
1
GND
8 VTT
EN 2
7 VTT_IN
VTTS 3
6 VCC
VREF 4
5 VDDQ
◎BD3532KN
●PIN CONFIGRATION
NC
NC
NC
NC
VTT1
VDDQ
VTT2
VREFS
NC
VREF
NC
NC
NC
NC
NC
PGND1
SGND
NC
VTTS
EN
PGND2
◎BD3533EKN
●PIN CONFIGRATION
NC
15
11
13
12
VTT 16
10 VDDQ
NC 17
9 NC
8 NC
NC 18
NC 19
7 NC
PGND 20
6 VREFS
2
DGND EN
VTTS
Enable Input Pin
Detector Pin for Termination Voltage
4
VREF
Reference Voltage Output Pin
5
VDDQ
6
VCC
7
VTT_IN
8
VTT
Reference Voltage Input Pin
VCC Pin
Termination Input Pin
Termination Output Pin
PIN NAME
PGND1
PGND2
SGND
EN
N.C.
VTTS
N.C.
N.C.
N.C.
VREF
VREFS
VDDQ
N.C.
N.C.
N.C.
VCC
N.C.
N.C.
VTT_IN1
VTT_IN2
N.C.
N.C.
N.C.
VTT1
VTT2
N.C.
N.C.
N.C.
PIN FUNCTION
Power Ground Pin 1
Power Ground Pin 2
Ground Pin for Reference Voltage
Enable Input Pin
Non Connection
Detector Pin for Termination Voltage
Non Connection
Non Connection
Non Connection
Reference Voltage Output Pin
Detector Pin for Reference Voltage
Reference Voltage Input Pin
Non Connection
Non Connection
Non Connection
VCC Pin
Non Connection
Non Connection
Termination Input Pin 1
Termination Input Pin 2
Non Connection
Non Connection
Non Connection
Termination Output Pin 1
Termination Output Pin 2
Non Connection
Non Connection
Non Connection
●PIN FUNCTION
VTT VTT_IN VTT_IN VCC
1
EN
3
PIN No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
NC
VCC
VTT_IN1 NC
NC
14
2
●PIN FUNCTION
VTT_IN2
NC
PIN FUNCTION
GND Pin
3
NC
4
5
VTTS VREF
9/16
PIN No.
PIN NAME
1
DGND
PIN FUNCTION
Digital Ground Pin
2
EN
Enable Input Pin
3
NC
Non Connection
4
VTTS
Detector Pin for Termination Voltage
5
VREF
Reference Voltage Output Pin
6
VREFS
7
NC
Non Connection
8
NC
Non Connection
9
NC
Non Connection
10
VDDQ
11
NC
Detector Pin for Reference Voltage
Reference Voltage Input Pin
Non Connection
12
VCC
13
VTT_IN
VCC Pin
Termination Input Pin
14
VTT_IN
Termination Input Pin
15
VTT
16
VTT
Termination Output Pin
17
NC
Non Connection
18
NC
Non Connection
19
NC
Non Connection
20
PGND
Termination Output Pin
Power Ground Pin
◎BD3532EFV
●PIN CONFIGRATION
VTT1
VTT2
●PIN FUNCTION
PIN No.
PIN NAME
1
VTT1
AGND
NC
PIN FUNCTION
Termination Output Pin 1
2
VTT2
3
PGND1
Power Ground Pin 1
Termination Output Pin 2
4
PGND2
Power Ground Pin 2
5
SGND
6
EN
Ground Pin for Reference Voltage
PGND1
NC
7
VTTS
Detector Pin for Termination Voltage
PGND2
VTT_IN
8
N.C.
Non Connection
9
VREF
SGND
VTT_IN
10
VREFS
11
N.C.
12
VDDQ
13
N.C.
Non Connection
VCC
14
VCC
VCC Pin
15
N.C.
Non Connection
NC
16
VTT_IN1
17
VTT_IN2
18
N.C.
Non Connection
19
N.C.
Non Connection
20
AGND
-
FIN
EN
VTTS
NC
VREF
VREFS
NC
VDDQ
NC
Enable Input Pin
Reference Voltage Output Pin
Detector Pin for Reference Voltage
Non Connection
Reference Voltage Input Pin
Termination Input Pin 1
Termination Input Pin 2
Ground Pin for Analog Ground
Substrate (Connected to AGND)
●Description of operations
・VCC
In BD3533/31/32, an independent power input pin is provided for an internal circuit operation of the IC. This is used to drive
the amplifier circuit of the IC, and its maximum current rating is 4 mA. The power supply voltage is 3.3 to 5.5 volts (BD3533)
or 5 volts (BD3531/32). It is recommended to connect a bypass capacitor of 1 μF or so to VCC.
・VDDQ
Reference input pin for the output voltage, that may be used to satisfy the JEDEC requirement for DDR-SDRAM (VTT =
1/2VDDQ) by dividing the voltage inside the IC with two 50 kΩ voltage-divider resistors
For BD3533, care must be taken to an input noise to VDDQ pin because this IC also cuts such noise input into half and
provides it with the voltage output divided in half. Such noise may be reduced with an RC filter consisting of such resistance
and capacitance (220 Ω and 2.2 μF, for instance) that may not give significant effect to voltage dividing inside the IC.
・VTT_IN
VTT_IN is a power supply input pin for VTT output. Voltage in the range between 1.0 and 5.5 volts may be supplied to this
VTT_IN terminal, but care must be taken to the current limitation due to on-resistance of the IC and the change in allowable
loss due to input/output voltage difference.
Generally, the following voltages are supplied:
・ DDR I VTT_IN=2.5V
・ DDRII VTT_IN=1.8V
Higher impedance of the voltage input at VTT_IN may result in oscillation or degradation in ripple rejection, which must be
noted. To VTT_IN terminal, it is recommended to use a 10 μF capacitor characterized with less change in capacitance. But
it may depend on the characteristics of the power supply input and the impedance of the pc board wiring, which must be
carefully checked before use.
・VREF
In BD3533/31/32, a reference voltage output pin independent from VTT output is given to provide a reference input for a
memory controller and a DRAM. Even if EN pin turns to “Low” level, VREF output is kept unchanged, compatible with “Self
Refresh” state of DRAM. The maximum current capability of VREF is 20 mA, and a suitable capacitor is needed to stabilize
the output voltage. It is recommended to use a combination of a 1.0 to 2.2 μF ceramic capacitor characterized with less
change in capacitance and a 0.5 to 2.2 Ω phase compensator resistor, or a 10μF ceramic or tantalum capacitor instead. For
an application where VREF current is low, a capacitor of lower capacitance may be used. If VREF current is 1 mA or less, it
is possible to secure a phase margin with a ceramic capacitor of 1 μF more or less.
・VTTS
An independent pin provided to improve load regulation of VTT output. In case that longer wiring is needed to the load at
VTT output, connecting VTTS from the load side may improve the load regulation.
10/16
・VTT
A DDR memory termination output pin. BD3533/31/32 has a sink/source current capability of ±1.0A/±1.5A/±3.0A
respectively. The output voltage tracks the voltage divided in half at VDDQ pin. VTT output is turned to OFF when VCC
UVLO or thermal shutdown protector is activated with EN pin level turned to “Low”. Do not fail to connect a capacitor to
VTT output pin for a loop gain phase compensation and a reduction in output voltage variation in the event of sudden change
in load. Insufficient capacitance may cause an oscillation. High ESR (Equivalent Series Resistance) of the capacitor may
result in increase in output voltage variation in the event of sudden change in load. It is recommended to use a 220 μF
functional polymer capacitor (OS-CON, POS-CAP, NEO-CAP), though it depends on ambient temperature and other
conditions. A low ESR ceramic capacitor may reduce a loop gain phase margin and may cause an oscillation, which may
be improved by connecting a resistor in series with the capacitor.
・EN
With an input of 2.3 volts or higher, the level at EN pin turns to “High” to provide VTT output. If the input is lowered to 0.8
volts or less, the level at EN pin turns to “Low” and VTT status turns to Hi-Z. But if VCC and VDDQ are established, VREF
output is maintained.
●Evaluation Board
■ BD3533F Evaluation Board Circuit
VCC
EN
GND
BD3533F
SW1
2 EN
VTT_IN
VDDQ
C5,C6
GND
U1
J2
R4
VCC
7 VTT_IN
VTT 8
5 VDDQ
VTTS 3
VREF
VREF 4
VCC
VTT
VTTS
J1
C9
6
C3,C4
C7 C8 C10
R1
C2
1 GND
C1
■ BD3533F Evaluation Board Application Components
Part No
U1
R1
R4
J1
J2
C1
C2
C3
Value
220Ω
0Ω
0Ω
10uF
1uF
Company
ROHM
ROHM
KYOCERA
KYOCERA
Parts Name
Part No
BD3533F
MCR032200
CM21B106M06A
CM105B105K06A
C4
C5
C6
C7
C8
C9
C10
Value
10uF
2.2uF
220uF
Company
KYOCERA
KYOCERA
SANYO
Parts Name
CM21B106M06A
CM105B225K06A
2R5TPE220MF
■ BD3533F(SOP8) Evaluation Board Layout
Silk Screen
TOP Layer
Bottom Layer
Versions for MSOP8 and HQFN20V packages are also available.
In addition, BD3533F/FVM/EKN(1A), BD3531F(1.5A), and BD3532F/EFV/KN(3A) are available.
11/16
● Heat loss
Thermal design must be conducted with the operation under the conditions listed below (which are the guaranteed
temperature range requiring consideration on appropriate margins etc.):
1. Ambient temperature Ta: 100°C or lower
2. Chip junction temperature Tj: 150°C or lower
The chip junction temperature Tj can be considered as follows. See Page 14/16 for θja.
Most of heat loss in BD3533/31/32 occurs at the output N-channel FET. The power lost is determined by multiplying the
voltage between VIN and Vo by the output current. As this IC employs the power PKG, the thermal derating characteristics
significantly depends on the pc board conditions. When designing, care must be taken to the size of a pc board to be used.
Power dissipation (W) = {Input voltage (VTT_IN) – Output voltage (VTT=1/2VDDQ)}×Io (Ave)
If VTT_IN = 1.8 volts, VDDQ=1.8 volts, and Io (Ave)=0.5 A, for instance, the power dissipation is determined as follows:
Power dissipation (W) = {1.8 (V) – 0.9 (V)} × 0.5 (A) = 0.4 (W)
●NOTE FOR USE
1.Absolute maximum ratings
For the present product, thoroughgoing quality control is carried out, but in the event that applied voltage, working
temperature range, and other absolute maximum rating are exceeded, the present product may be destroyed. Because it is
unable to identify the short mode, open mode, etc., if any special mode is assumed, which exceeds the absolute maximum
rating, physical safety measures are requested to be taken, such as fuses, etc.
2.GND potential
Bring the GND terminal potential to the minimum potential in any operating condition.
3.Thermal design
Consider allowable loss (Pd) under actual working condition and carry out thermal design with sufficient margin provided.
4.Terminal-to-terminal short-circuit and erroneous mounting
When the present IC is mounted to a printed circuit board, take utmost care to direction of IC and displacement. In the event
that the IC is mounted erroneously, IC may be destroyed. In the event of short-circuit caused by foreign matter that enters in
a clearance between outputs or output and power-GND, the IC may be destroyed.
5.Operation in strong electromagnetic field
The use of the present IC in the strong electromagnetic field may result in maloperation, to which care must be taken.
6.Built-in thermal shutdown protection circuit
The present IC incorporates a thermal shutdown protection circuit (TSD circuit). The working temperature is 175°C
(standard value) and has a -15°C (standard value) hysteresis width. When the IC chip temperature rises and the TSD circuit
operates, the output terminal is brought to the OFF state. The built-in thermal shutdown protection circuit (TSD circuit) is first
and foremost intended for interrupt IC from thermal runaway, and is not intended to protect and warrant the IC.
Consequently, never attempt to continuously use the IC after this circuit is activated or to use the circuit with the activation of
the circuit premised.
7.Capacitor across output and GND
In the event a large capacitor is connected across output and GND, when Vcc and VIN are short-circuited with 0V or GND for
some kind of reasons, current charged in the capacitor flows into the output and may destroy the IC. Use a capacitor smaller
than 1000 μF between output and GND.
8.Inspection by set substrate
In the event a capacitor is connected to a pin with low impedance at the time of inspection with a set substrate, there is a fear
of applying stress to the IC. Therefore, be sure to discharge electricity for every process. As electrostatic measures,
provide grounding in the assembly process, and take utmost care in transportation and storage. Furthermore, when the set
substrate is connected to a jig in the inspection process, be sure to turn OFF power supply to connect the jig and be sure to
turn OFF power supply to remove the jig.
9. Inputs to IC terminals
+
This device is a monolithic IC with P isolation between P-substrate and each element as illustrated below. This P-layer and
the N-layer of each element form a PN junction which works as:
・a diode if the electric potentials at the terminals satisfy the following relationship; GND>Terminal A>Terminal B, or
・a parasitic transistor if the electric potentials at the terminals satisfy the following relationship; Terminal B>GND Terminal A.
The structure of the IC inevitably forms parasitic elements, the activation of which may cause interference among circuits,
and/or malfunctions contributing to breakdown. It is therefore requested to take care not to use the device in such manner
that the voltage lower than GND (at P-substrate) may be applied to the input terminal, which may result in activation of
parasitic elements.
Resistor
NPN Transistor Structure (NPN)
(PIN B)
(PIN A)
E
C
Parasitic diode
GND
N
P+
P+
P
P
P+
N
GND
(PIN B)
P+
N
N
N
P substrate
(PIN A)
B
N
Parasitic diode
GND
C
N
B
E
P substrate
Parasitic diode
GND
GND
Nearby other device
Parasitic diode
12/16
10. GND wiring pattern
When both a small-signal GND and high current GND are present, single-point grounding (at the set standard point) is
recommended, in order to separate the small-signal and high current patterns, and to be sure the voltage change stemming
from the wiring resistance and high current does not cause any voltage change in the small-signal GND. In the same way,
care must be taken to avoid wiring pattern fluctuations in any connected external component GND.
11. Output capacitor (C1)
Do not fail to connect a output capacitor to VREF output terminal for stabilization of output voltage. The capacitor connected
to VREF output terminal works as a loop gain phase compensator. Insufficient capacitance may cause an oscillation. It is
recommended to use a low temperature coefficient 1-10 μF ceramic capacitor, though it depends on ambient temperature and
load conditions. It is therefore requested to carefully check under the actual temperature and load conditions to be applied.
12. Output capacitor (C4)
Do not fail to connect a capacitor to VTT output pin for stabilization of output voltage. This output capacitor works as a loop
gain phase compensator and an output voltage variation reducer in the event of sudden change in load. Insufficient
capacitance may cause an oscillation. And if the equivalent series resistance (ESR) of this capacitor is high, the variation in
output voltage increases in the event of sudden change in load. It is recommended to use a 47-220 μF functional polymer
capacitor, though it depends on ambient temperature and load conditions. Using a low ESR ceramic capacitor may reduce a
loop gain phase margin and cause an oscillation, which may be improved by connecting a resistor in series with the capacitor.
It is therefore requested to carefully check under the actual temperature and load conditions to be applied.
13. Input capacitors (C2 and C3)
These input capacitors are used to reduce the output impedance of power supply to be connected to the input terminals (VCC
and VTT_IN). Increase in the power supply output impedance may result in oscillation or degradation in ripple rejecting
characteristics. It is recommended to use a low temperature coefficient 1μF (for VCC) and 10μF (for VTT_IN) capacitor, but
it depends on the characteristics of the power supply input, and the capacitance and impedance of the pc board wiring pattern.
It is therefore requested to carefully check under the actual temperature and load conditions to be applied.
14. Input terminals (VCC, VDDQ, VTT_IN and EN)
VCC, VDDQ, VTT_IN and EN terminals of this IC are made up independent one another. To VCC terminal, the UVLO
function is provided for malfunction protection. Irrespective of the input order of the inputs terminals, VTT output is activated
to provide the output voltage when UVLO and EN voltages reach the threshold voltage while VREF output is activated when
UVLO voltage reaches the threshold. If VDDQ and VTT_IN terminals have equal potential and common impedance, any
change in current at VTT_IN terminal may result in variation of VTT_IN voltage, which affects VDDQ terminal and may cause
variation in the output voltage. It is therefore required to perform wiring in such manner that VDDQ and VTT_IN terminals
may not have common impedance. If impossible, take appropriate corrective measures including suitable CR filter to be
inserted between VDDQ and VTT_IN terminals.
15. VTTS terminal
A terminal used to improve load regulation of VTT output. Connection with VTT terminal must be done not to have common
impedance with high current line, which may offer better load regulation of VTT output.
16. Operating range
Within the operating range, the operation and function of the circuits are generally guaranteed at an ambient temperature
within the range specified. The values specified for electrical characteristics may not be guaranteed, but drastic change may
not occur to such characteristics within the operating range.
17. Allowable loss Pd
For the allowable loss, the thermal derating characteristics are shown in the Exhibit, which should be used as a guide. Any
uses that exceed the allowable loss may result in degradation in the functions inherent to IC including a decrease in current
capability due to chip temperature increase. Use within the allowable loss.
18. Built-in thermal shutdown protection circuit
Thermal shutdown protection circuit is built-in to prevent thermal breakdown. Turns VTT output to OFF when the thermal
shutdown protection circuit activates. This thermal shutdown protection circuit is originally intended to protect the IC itself.
It is therefore requested to conduct a thermal design not to exceed the temperature under which the thermal shutdown
protection circuit can work.
19. The use in the strong electromagnetic field may sometimes cause malfunction, to which care must be taken.
In the event that load containing a large inductance component is connected to the output terminal, and generation of
back-EMF at the start-up and when output is turned OFF is assumed, it is requested to insert a protection diode.
20. In the event that load containing a large inductance component is
(Example)
connected to the output terminal, and generation of back-EMF at the
OUTPUT PIN
start-up and when output is turned OFF is assumed, it is requested
to insert a protection diode.
21. We are certain that examples of applied circuit diagrams are recommendable,
but you are requested to thoroughly confirm the characteristics before using the IC.
In addition, when the IC is used with the external circuit changed, decide the IC with sufficient margin provided
while consideration is being given not only to static characteristics but also variations of external parts and our IC including
transient characteristics.
13/16
●POWER DISSIPATION
◎SOP8(BD3533F/31F/32F)
◎MSOP8(BD3533FVM)
[W]
[mW]
[mW]
700
600
◎HQFN20V(BD3533EKN)
2.5
500
437.5mW
(1) 690mW
2.0
500
(2) 560mW
400
100℃
300
200
Power Dissipation [Pd]
Power Dissipation [Pd]
Power Dissipation [Pd]
400
300
100℃
200
(2) 1.75W
1.5
1.0
(3) 0.75W
0.5
100
(1) 2.0W
(4) 0.5W
100
0
0
0
0
25
50
75
100
125
150
[℃]
Ambient Temperature [Ta]
(1) 70mm×70mm×1.6mm Glass-epoxy PCB
θj-c=181℃/W
(2) With no heat sink
θj-a=222℃/W
0
25
50
100
PCB②:θja=86.2℃/W
Power Dissipation [Pd]
③2.30W
2
②1.45W
①1.00W
(2) 460mW
400
100℃
300
200
100
0
0
25
50
75
100
125
0
150
Ambient Temperature Ta(℃)
measure:TH-156(Kuwano Denki)
measure condition:Rohm Standard Board
PCB size:70mm×70mm×1.6mmt
(Thermal vias in the board) Connect the board with the exposed
area at the bottom surface of the package by soldering.
PCB①:Single-layer substrate
PCB②:Double-layer substrate(substrate surface copper foil area : 15mm×15mm)
PCB③:Double-layer substrate(substrate surface copper foil area : 70mm×70mm)
14/16
100
125
150
[℃]
(1) With no heat sink
θj-a=250℃/W
(2) PCB (substrate surface copper foil area : None)
θj-a=166.7℃/W
(3) PCB Single-layer substrate
(substrate surface copper foil area : 15mm×15mm)
θj-a=71.4℃/W
(4) PCB Double-layer substrate
(substrate surface copper foil area : 60mm×60mm)
θj-a=62.5℃/W
(1) 725mW
500
75
Ambient Temperature [Ta]
600
PCB③:θja=54.3℃/W
PCB④:θja=39.1℃/W
1
[℃]
50
700
PCB①:θja=125.0℃/W
3
25
◎VQFN28(BD3532KN)
[mW]
800
④3.20W
0
150
Ambient Temperature [Ta]
5
4
125
With no heat sink
θj-a=286℃/W
◎HTSSOP-B20(BD3532EFV)
Power Dissipation [Pd]
75
25
50
75
100
125
Ambient Temperature [Ta]
150
[℃]
(2) 70mm×70mm×1.6mm Glass-epoxy PCB
θj-c=172℃/W
(2) With no heat sink
θj-a=270℃/W
●Ordering part number
B
D
3
Part Number
5
3
3
F
V
Package Type
・BD3533
・BD3531
・BD3532
M
-
T
R
TR Emboss tape reel opposite draw-out side: 1 pin
E2 Emboss tape reel opposite draw-out side: 1 pin
・F : SOP8
・FVM : MSOP8
・HFV : HTSSOP-B20
・KN : VQFN28
・EKN : HQFN20V
SOP8
<Tape and Reel information>
<Dimension>
1
4
2500pcs
E2
(The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand)
0.15±0.1
1234
1234
1234
1234
Direction of feed
1Pin
Reel
(Unit:mm)
1234
1234
1234
0.1
1.27
0.4±0.1
1234
1.5±0.1
0.11
6.2±0.3
4.4±0.2
0.3Min.
5
Embossed carrier tape
Quantity
Direction
of feed
5.0±0.2
8
Tape
※When you order , please order in times the amount of package quantity.
MSOP8
<Dimension>
<Tape and Reel information>
Tape
5
1
4
0.29 ± 0.15
0.6 ± 0.2
8
2.8 ± 0.1
4.0 ± 0.2
2.9 ± 0.1
0.9Max.
0.75 ± 0.05
0.08 ± 0.05
Quantity
3000pcs
Direction
of feed
TR
(The direction is the 1pin of product is at the upper light when you hold
reel on the left hand and you pull out the tape on the right hand)
0.145 +0.05
−0.03
0.475
0.22
0.65
Embossed carrier tape
+0.05
−0.04
0.08 M
X X
X
X
X X X
0.08 S
X X
X
X
X X X
X X
X
X
X X X
X X
X
X
X X X
X X
X
X
X X X
Direction of feed
1Pin
Reel
(Unit:mm)
※When you order , please order in times the amount of package quantity.
HTSSOP-B20
<Dimension>
<Tape and Reel information>
6.5 ± 0.1
11
6.4 ± 0.2
4.4 ± 0.1
0.5 ± 0.15
1.0 ± 0.2
20
1
10
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
(The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand)
0.17 +0.05
−0.03
S
0.08 S
1234
1234
1234
1pin
1234
1234
Reel
(Unit:mm)
1234
0.2 +0.05
−0.04
1234
0.65
1234
1.0Max.
0.85 ± 0.05
0.08 ± 0.05
0.325
Tape
Direction of feed
※When you order , please order in times the amount of package quantity.
15/16
VQFN28
<Dimension>
<Tape and Reel information>
5.2±0.1
5.0±0.1
(1.1)
15
21
5)
5.0±0.1
5.2±0.1
.
(0
14
.3
(0
3−
22
1
Quantity
2500pcs
Direction
of feed
E2
(The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand)
22
(0
.
0.5
7
0.22±0.05
Embossed carrier tape(with dry pack)
)
5)
8
28
Tape
1234
1234
1234
1pin
Reel
(Unit:mm)
1234
0.05
1234
0.1
(0.6 −+0.3
)
1234
0.22 ± 0.05
0.03
0.02 −+0.02
0.95MAX
0.05
Direction of feed
※When you order , please order in times the amount of package quantity.
HQFN20V
<Tape and Reel information>
<Dimension>
(2.1)
4.2±0.1
4.0±0.1
0.5
(1.1)
11
6
Quantity
2500pcs
Direction
of feed
E2
(The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand)
5)
.3
(0
0.22±0.05
5
Embossed carrier tape(with dry pack)
3−
1
(2.1)
10
20
.2
16
(0
4.0±0.1
0.05
0.1
0.6 −+0.3
1234
1234
1234
1234
1234
1234
0.22±0.05
)
.5
(0
0.03
0.02 −+0.02
0.95MAX
4.2±0.1
2)
15
Tape
0.05
Reel
(Unit:mm)
1pin
Direction of feed
※When you order , please order in times the amount of package quantity.
16/16
Catalog No.08T461A '08.10 ROHM ©
Appendix
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM
CO.,LTD.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you
wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM
upon request.
Examples of application circuits, circuit constants and any other information contained herein illustrate the
standard usage and operations of the Products. The peripheral conditions must be taken into account when
designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document. However, should
you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and examples of
application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or
exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility
whatsoever for any dispute arising from the use of such technical information.
The Products specified in this document are intended to be used with general-use electronic equipment or
devices (such as audio visual equipment, office-automation equipment, communication devices, electronic
appliances and amusement devices).
The Products are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or
malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the
possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as
derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your
use of any Product outside of the prescribed scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system
which requires an extremely high level of reliability the failure or malfunction of which may result in a direct
threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,
aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no
responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended
to be used for any such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may be controlled under
the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2008 ROHM CO.,LTD.
THE AMERICAS / EUROPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix1-Rev3.0
Similar pages