Rohm BD46291 Counter timer built-in cmos voltage detector ic Datasheet

Voltage Detector IC Series
Counter Timer Built-in
CMOS Voltage Detector IC
No.09006ECT06
BD45□□□G, BD46□□□G series
 Description
ROHM’s BD45□□□G and BD46□□□G series are highly accurate, low current consumption reset IC series. Because the
counter timer delay circuit is built into those series, an external capacitor for the delay time setting is unnecessary. The
lineup was established with tow output types (Nch open drain and CMOS output) and detection voltages range from 2.3V to
4.8V in increments of 0.1V, so that the series may be selected according the application at hand.
 Features
1) Detection voltage: 2.3V to 4.8V (Typ.), 0.1V steps
2) High accuracy detection voltage:±1.0%
3) Ultra-low current consumption: 0.85µA (Typ.)
4) Operating temperature range: -40°C to +105°C
6) SSOP5 compact surface mount packages
5) Three internal, fixed delay time: 50ms, 100ms and 200ms
7) Nch open drain output (BD45□□□G), CMOS output (BD46□□□G)
 Applications
All electronic devices that use microcontrollers and logic circuits
 Selection Guide
No.
1
Part Number : BD4
G
1
2
2
Specifications
Output Circuit Format
Detection Voltage
3
3
Fixed Delay Times
Description
5:Open Drain Output, 6:CMOS Output
Example: Displays VDET over a 2.3V to 4.8V range
in 0.1V increments. (2.9V is marked as “29”)
5: 50ms(Typ.), 1: 100ms(Typ.)
2: 200ms(Typ.)
 Lineup
Detection
Voltage
Marking
Part
Number
Marking
Part
Number
Marking
Part
Number
Marking
Part
Number
Marking
Part
Number
Marking
Part
Number
4.8V
4.7V
4.6V
4.5V
4.4V
4.3V
4.2V
4.1V
4.0V
3.9V
3.8V
3.7V
3.6V
3.5V
3.4V
3.3V
3.2V
3.1V
3.0V
2.9V
2.8V
2.7V
2.6V
2.5V
2.4V
2.3V
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
TA
TB
TC
TD
TE
TF
TG
TH
TJ
TK
TL
TM
TN
TP
TQ
TR
BD45485
BD45475
BD45465
BD45455
BD45445
BD45435
BD45425
BD45415
BD45405
BD45395
BD45385
BD45375
BD45365
BD45355
BD45345
BD45335
BD45325
BD45315
BD45305
BD45295
BD45285
BD45275
BD45265
BD45255
BD45245
BD45235
TS
TT
TU
TV
TW
TX
TY
TZ
U0
U1
U2
U3
U4
U5
U6
U7
U8
U9
UA
UB
UC
UD
UE
UF
UG
UH
BD45481
BD45471
BD45461
BD45451
BD45441
BD45431
BD45421
BD45411
BD45401
BD45391
BD45381
BD45371
BD45361
BD45351
BD45341
BD45331
BD45321
BD45311
BD45301
BD45291
BD45281
BD45271
BD45261
BD45251
BD45241
BD45231
UJ
UK
UL
UM
UN
UP
UQ
UR
US
UT
UU
UV
UW
UX
UY
UZ
V0
V1
V2
V3
V4
V5
V6
V7
V8
V9
BD45482
BD45472
BD45462
BD45452
BD45442
BD45432
BD45422
BD45412
BD45402
BD45392
BD45382
BD45372
BD45362
BD45352
BD45342
BD45332
BD45322
BD45312
BD45302
BD45292
BD45282
BD45272
BD45262
BD45252
BD45242
BD45232
VA
VB
VC
VD
VE
VF
VG
VH
VJ
VK
VL
VM
VN
VP
VQ
VR
VS
VT
VU
VV
VW
VX
VY
VZ
W0
W1
BD46485
BD46475
BD46465
BD46455
BD46445
BD46435
BD46425
BD46415
BD46405
BD46395
BD46385
BD46375
BD46365
BD46355
BD46345
BD46335
BD46325
BD46315
BD46305
BD46295
BD46285
BD46275
BD46265
BD46255
BD46245
BD46235
W2
W3
W4
W5
W6
W7
W8
W9
WA
WB
WC
WD
WE
WF
WG
WH
WJ
WK
WL
WM
WN
WP
WQ
WR
WS
WT
BD46481
BD46471
BD46461
BD46451
BD46441
BD46431
BD46421
BD46411
BD46401
BD46391
BD46381
BD46371
BD46361
BD46351
BD46341
BD46331
BD46321
BD46311
BD46301
BD46291
BD46281
BD46271
BD46261
BD46251
BD46241
BD46231
WU
WV
WW
WX
WY
WZ
X0
X1
X2
X3
X4
X5
X6
X7
X8
X9
XA
XB
XC
XD
XE
XF
XG
XH
XJ
XK
BD46482
BD46472
BD46462
BD46452
BD46442
BD46432
BD46422
BD46412
BD46402
BD46392
BD46382
BD46372
BD46362
BD46352
BD46342
BD46332
BD46322
BD46312
BD46302
BD46292
BD46282
BD46272
BD46262
BD46252
BD46242
BD46232
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
1/9
2009.05 - Rev.C
Technical Note
BD45□□□G, BD46□□□G series
 Absolute maximum ratings (Ta=25°C)
Parameter
Power Supply Voltage
Nch Open Drain Output
Output Voltage
CMOS Output
ER pin Voltage
*1 *2
Power Dissipation
Operating Temperature
Ambient Storage Temperature
Symbol
VDD-GND
Limits
-0.3 ~ +10
GND-0.3 ~ +10
GND-0.3 ~ VDD+0.3
GND-0.3 ~ VDD+0.3
540
-40 ~ +105
-55 ~ +125
VOUT
VCT
Pd
Topr
Tstg
Unit
V
V
V
mW
°C
°C
*1 Use above Ta=25°C results in a 5.4mW loss per degree.
*2 When mounted on a 70mm×70mm×1.6mm glass epoxy board.
 Electrical characteristics (Unless Otherwise Specified Ta=-40 to 105°C)
Parameter
Symbol
*1
Detection Voltage
VDET
VDD=HL, RL=470kΩ
Detection Voltage
Temperature coefficient
VDET/
∆T
-40°C~+105°C
Hysteresis Voltage
∆VDET
VDD=LHL, RL=470kΩ
‘High’ Output
Delay time
-
BD4XXX5G
CL=100pF,
tPLH
Limit
Min.
Typ.
Max.
VDET(T)
VDET(T)
VDET(T)
×0.99
×1.01
Condition
RL=100kΩ
BD4XXX1G
*1, *2, *3
BD4XXX2G
VDD=VDET-0.2V, VER=0V VDET=2.3V~3.1V
*1
VDD=VDET-0.2V, VER=0V VDET=2.3V~3.1V
Circuit Current
when ON
IDD1
VDD=VDET-0.2V, VER=0V VDET=3.2V~4.2V
*1
VDD=VDET-0.2V, VER=0V VDET=3.2V~4.2V
VDD=VDET-0.2V, VER=0V VDET=4.3V~4.8V
*1
VDD=VDET-0.2V, VER=0V VDET=4.3V~4.8V
VDD=VDET+0.2V, VER=0V VDET=2.3V~3.1V
*1
VDD=VDET+0.2V, VER=0V VDET=2.3V~3.1V
Circuit Current
when OFF
IDD2
VDD=VDET+0.2V, VER=0V VDET=3.2V~4.2V
VDD=VDET+0.2V, VER=0V VDET=3.2V~4.2V
VDD=VDET+0.2V, VER=0V VDET=4.3V~4.8V
Operating Voltage Range
‘High’ Output Current
‘Low’Output Current (Nch)
Leak Current when OFF
ER Pin ‘H’ Voltage
ER Pin ‘L’ Voltage
ER Pin Input Current
VOPL
IOH
IOL
Ileak
VEH
VEL
IEL
*1
*1
VDD=VDET+0.2V, VER=0V VDET=4.3V~4.8V
VOL≤0.4V, RL=470kΩ, Ta=25~105°C
VOL≤0.4V, RL=470kΩ, Ta=-40~25°C
VDS=0.5V,VDD=6.0V,VDET≥4.3V
VDS=0.5V, VDD=1.2V
VDS=0.5V, VDD=2.4V VDET=2.7V~4.8V
*1
VDD=VDS=10V
*1
*1
±100
±360
VDET(T) VDET(T) VDET(T)
×0.03
×0.05
×0.08
45
50
55
90
100
110
180
200
220
0.70
2.10
0.70
2.85
0.75
2.25
0.75
3.00
0.80
2.40
0.80
3.15
0.75
2.25
0.75
4.28
0.80
2.40
0.80
4.50
0.85
2.55
0.85
4.73
0.95
1.20
1.2
2.7
0.4
1.2
2.0
5.0
0.1
2.0
0.8
1
10
Unit
V
ppm/°C
V
ms
µA
µA
V
mA
mA
µA
V
V
µA
VDET(T):Standard Detection Voltage (2.3V to 4.8V, 0.1V step)
RL :Pull-up resistor to be connected between VOUT and power supply.
CL :Capacitor to be connected between VOUT and GND.
*1 Guarantee is Ta=25°C.
*2 tPLH:VDD=(VDET(T)-0.5V)(VDET(T)+0.5V)
*3 tPLH:VDD=Please set up the rise up time between VDD=0VDET more than 100µs.
Attention: Please connect the GND when you don’t use ‘ER’
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2/9
2009.05 - Rev.C
Technical Note
BD45□□□G, BD46□□□G series
 Block Diagrams
BD45□□□G
BD46□□□G
VDD
VDD
Oscillation
VOUT
Oscillation
Circuit Counter
Circuit Counter
Timer
Timer
Vref
VOUT
Vref
GND
ER
GND
Fig.1
Fig.2
TOP VIEW
SSOP5
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
ER
PIN No.
Symbol
Function
1
ER
2
SUB
Substrate *
3
GND
GND
4
VOUT
Reset Output
5
VDD
Power Supply Voltage
Manual Reset
*Connect the substrate to GND.
3/9
2009.05 - Rev.C
Technical Note
BD45□□□G, BD46□□□G series
 Reference Data (Unless specified otherwise, Ta=25°C)
【BD45281G】
1.5
1.0
0.5
0.0
0
1
2
3
4
5
6
7
8
【BD45281G】
15
VDD =2.4V
10
5
VDD =1.2V
0
0.0
9 10
0.5
2.0
VDD =6.0V
10
VDD =4.8V
5
0
2.5
0
1
2
3
4
5
6
Fig.3 Circuit Current
Fig.4 “Low” Output Current
Fig.5 “High” Output Current
20
4
3
Ta=25℃
2
1
Ta=25℃
15
10
5
【BD45421G】
ER BIAS CURRENT : IER[μA]
5
20
【BD46281G】
OUTPUT VOLTAGE: VOUT [V]
【BD45421G】
6
0
1
2
4.6
4.2
High to low(VDET)
3.4
0
40
5
6
7
8
80
Fig.9 Detection Voltage
Release Voltage
1.5
PLH [msec]
"HIGH" DELAY
DELAY TIME
TIME :: ttPLH
“HIGH”
[ms]
【BD45421G】
1.0
0.5
20
40
60
80
1
2
【BD45421G】
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
-40
-20
0
20
40
60
100
3
4
5
6
7
8
9 10
ER VOLTAGE : VER [V]
Fig.8 ER Terminal Input Current
80
100
3.0
2.8
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
-40 -20
【BD45421G】
0
20
40
60
80
100
TEMPERATURE : Ta[℃]
TEMPERATURE : Ta[℃]
Fig.10 Circuit Current when ON
(VDET-0.2V)
Fig.11 Circuit Current when OFF
250
50
【BD4528□G】
200
BD45282G
150
BD45281G
100
50
BD45285G
【BD45281G tPHL 】
40
30
20
10
0
0
0
0
1.6
TEMPERATURE : Ta[℃]
-20
5
9 10
CIRCUIT CURRENT WHEN OFF : I DD2 [μA]
Low to high(VDET+ΔVDET)
3.0 ~
-40
4
: t:PHL
"LOW"
[μsec]
“LOW”DELAY
DELAYTIME
TIME
tPLH
[µs]
CIRCUIT CURRENT WHEN ON
【BD45421G】
3.8
3
Fig.7 ER Terminal Threshold Voltage
: IDD1 [μA]
5.8
5.0
10
ER VOLTAGE : VER[V]
Fig.6 I/O Characteristics
5.4
15
0
0
VDD SUPPLY VOLTAGE :VDD [V]
0.0
-40
15
DRAIN-SOURCE VOLTAGE : VDS[V]
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5
DETECTION VOLTAGE: VDET[V]
1.5
【BD46281G】
DRAIN-SOURCE VOLTAGE : VDS[V]
0
MINIMUM OPERATION VOLTAGE : V OPL[μA]
1.0
20
VDD SUPPLY VOLTAGE :VDD [V]
7
OUTPUT VOLTAGE: VOUT [V]
20
"HIGH" OUTPUT CURRENT : IOH [mA]
"LOW" OUTPUT CURRENT : IOL [mA]
CIRCUIT CURRENT : IDD [μA]
2.0
-60 -40 -20
0
20
40
60
80 100 120
-60 -40 -20
0
20
40
60
80 100 120
TEMPERATURE : Ta[℃]
TEMPERATURE : Ta[℃]
TEMPERATURE : Ta[℃]
Fig.12 Operating Limit Voltage
Fig.13 Output Delay Time
“Low””High”
Fig.14 Output Delay Time
“High””Low”
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
4/9
2009.05 - Rev.C
Technical Note
BD45□□□G, BD46□□□G series
 Reference Data
Examples of Leading (TPLH) and Falling (TPHL) Output
Part Number
tPLH[ms]
tPHL[µs]
BD45275G
50
18
BD46275G
50
18
VDD=2.2V3.2V
VDD=3.2V2.2V
*This data is for reference only.
The figures will vary with the application, so please confirm actual operating conditions before use.
 Explanation of Operation
For both the open drain type (Fig.15) and the CMOS output type (Fig.16), the detection and release voltages are used as
threshold voltages. When the voltage applied to the VDD pins reaches the applicable threshold voltage, the VOUT terminal
voltage switches from either “High” to “Low” or from “Low” to “High”. Because the BD45□□□G series uses an open drain output
type, it is possible to connect a pull-up resistor to VDD or another power supply [The output “High” voltage (VOUT) in this case
becomes VDD or the voltage of the other power supply].
VDD
VDD
VDD
R1
R1
Q2
Vref
Vref
Reset
VOUT
Oscillation
Oscillation
Circuit Counter
R2
R2
Timer
Reset
Circuit Counter
Timer
Q1
VOUT
Q1
R3
R3
GND
GND
ER
ER
Fig.15 (BD45□□□G Type Internal Block Diagram)
Fig.16 (BD46□□□G Type Internal Block Diagram)
 Timing Waveform
Example: the following shows the relationship between the input voltages VDD, the output voltage VOUT and ER terminal
when the input power supply voltage VDD is made to sweep up and sweep down (the circuits are those in Fig. 12 and 13).
1
VDD
VDD
VDET+ΔVDET
VDET
0V
⑦
VOPL
VOH
tPLH
tPLH
tPLH
VOUT
tPHL
VOL
tPHL
VEH
ER
tPHL
①
②
③ ④⑤
Fig.17
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
⑥
When the power supply is turned on, the output is unsettled from
after over the operating limit voltage (VOPL) until TPHL. There fore
it is possible that the reset signal is not outputted when the rise
time of VDD is faster than TPHL.
2 When VDD is greater than VOPL but less than the reset release
voltage (VDET + ∆VDET), the output voltages will switch to Low.
3 If VDD exceeds the reset release voltage (VDET + ∆VDET), the
counter timer start and VOUT switches from L to H.
4 When more than the high level voltage is supplied ER terminal,
VOUT comes to “L” after tPLH delay time. Therefore, a time when
ER terminal is “H” is necessary for 100µsec or more.
5 When the ER terminal switches to Low, the counter timer starts
to operate, a delay of tPLH occurs, and VOUT switches from “L” to
“H”.
6 If VDD drops below the detection voltage (VDET) when the
power supply is powered down or when there is a power supply
fluctuation, VOUT switches to L (with a delay of tPHL).
7 The potential difference between the detection voltage and the
release voltage is known as the hysteresis width (∆VDET). The
system is designed such that the output does not flip-flop with
power supply fluctuations within this hysteresis width, preventing
malfunctions due to noise.
These time changes by the application and use it, please verify
and confirm using practical applications.
5/9
2009.05 - Rev.C
Technical Note
BD45□□□G, BD46□□□G series
 Circuit Applications
1) Examples of a common power supply detection reset circuit.
VDD1
VDD2
RL
BD45□□□
Microcontroller
CL
(Noise-filtering
Capacitor)
GND
Application examples of BD45□□□G series (Open Drain
output type) and BD46□□□G series (CMOS output type)
are shown below.
CASE1: the power supply of the microcontroller (VDD2)
differs from the power supply of the reset detection
(VDD1).
Use the open drain output type (BD45□□□G) attached a
load resistance (RL) between the output and VDD2. (As
shown Fig.18)
Fig.18 Open Collector Output Type
CASE2: the power supply of the microcontroller (VDD1) is
same as the power supply of the reset detection (VDD1).
Use CMOS output type (BD46□□□G) or open drain output
type (BD45□□□G) attached a load resistance (RL)
between the output and Vdd1. (As shown Fig.19)
VDD1
BD46□□□
Microcontroller
CL
When a capacitance CL for noise filtering is connected to
the VOUT pin (the reset signal input terminal of the
microcontroller), please take into account the waveform of
the rise and fall of the output voltage (VOUT).
(Noise-filtering
Capacitor)
GND
Fig.19 CMOS Output Type
2) The following is an example of a circuit application in which an OR connection between two types of detection voltages
resets the microcontroller.
VDD1
VDD3
VDD2
RL
ER
BD45□□□
No.1
VOUT
ER
BD45□□□
No.2
VOUT
microcontroller
RST
GND
Fig.20
When there are many power supplies of the system, power supplies VDD1 and VDD2 are being monitored separately, and
it is necessary to reset the microcomputer, it is possible to use an OR connection on the open drain output type BD45□□□G
series to pull-up to the desired voltage (VDD3) as shown in Fig. 20 and make the output “High” voltage matches the power
supply voltage VDD3 of the microcontroller.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
6/9
2009.05 - Rev.C
Technical Note
BD45□□□G, BD46□□□G series
Examples of the power supply with resistor dividers
In applications where the power supply input terminal (VDD) of an IC with resistor dividers, it is possible that a through
current will momentarily flow into the circuit when the output logic switches, resulting in malfunctions (such as output
oscillatory state).
(Through-current is a current that momentarily flows from the power supply (VDD) to ground (GND) when the output level
switches from “High” to “Low” or vice versa.)
V1
R2
I1
R1
CIN
VDD
ER
BD45□□□G
BD46□□□G
VOUT
CL
GND
Fig.21
A voltage drop of [the through-current (I1)] × [input resistor (R2)] is caused by the through current, and the input voltage to
descends, when the output switches from “Low” to “High”. When the input voltage decreases and falls below the detection
voltage, the output voltage switches from “High” to “Low”. At this time, the through-current stops flowing through output
“Low”, and the voltage drop is eliminated. As a result, the output switches from “Low” to “High”, which again causes the
through current to flow and the voltage drop. This process is repeated, resulting in oscillation.
IDD
Through Current
VDD
VDET
0
Fig.22 Current Consumption vs. Power Supply Voltage
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
7/9
2009.05 - Rev.C
Technical Note
BD45□□□G, BD46□□□G series
 Operation Notes
(1) Absolute maximum range
Absolute Maximum Ratings are those values beyond which the life of a device may be destroyed. We cannot be defined the
failure mode, such as short mode or open mode. Therefore a physical security countermeasure, like fuse, is to be given
when a specific mode to be beyond absolute maximum ratings is considered.
(2) GND potential
GND terminal should be a lowest voltage potential every state.
Please make sure all pins, which are over ground even if, include transient feature.
(3) Electrical Characteristics
Be sure to check the electrical characteristics that are one the tentative specification will be changed by temperature,
supply voltage, and external circuit.
(4) Bypass Capacitor for Noise Rejection
Please put into the capacitor of 1µF or more between VDD pin and GND, and the capacitor of about 1000pF between VOUT
pin and GND, to reject noise. If extremely big capacitor is used, transient response might be late. Please confirm sufficiently
for the point.
(5) Short Circuit between Terminal and Soldering
Don’t short-circuit between Output pin and VDD pin, Output pin and GND pin, or VDD pin and GND pin. When soldering the
IC on circuit board, please be unusually cautious about the orientation and the position of the IC. When the orientation is
mistaken the IC may be destroyed.
(6) Electromagnetic Field
Mal-function may happen when the device is used in the strong electromagnetic field.
(7) The VDD line inpedance might cause oscillation because of the detection current.
(8) A VDD -GND capacitor (as close connection as possible) should be used in high VDD line impedance condition.
(9) Lower than the mininum input voltage makes the VOUT high impedance, and it must be VDD in pull up (VDD) condition.
(10) This IC has extremely high impedance terminals. Small leak current due to the uncleanness of PCB surface might
cause unexpected operations. Application values in these conditions should be selected carefully. If the leakage of about
1MΩ is assumed between the ER terminal and the GND terminal, 100kΩ connection between the ER terminal and the
VDD terminal would be recommended. If the leakage is assumed between the VOUT terminal and the GND terminal, the
pull-up resistor should be less than 1/10 of the assumed leak resistance.
(11) External parameters
The recommended parameter range for RL is 50kΩ~1MΩ. There are many factors (board layout, etc) that can affect
characteristics. Please verify and confirm using practical applications.
(12) Power on reset operation
Please note that the power on reset output varies with the VDD rise up time. Please verify the actual operation.
(13) Precautions for board inspection
Connecting low-impedance capacitors to run inspections with the board may produce stress on the IC. Therefore, be
certain to use proper discharge procedure before each process of the test operation.
To prevent electrostatic accumulation and discharge in the assembly process, thoroughly ground yourself and any
equipment that could sustain ESD damage, and continue observing ESD-prevention procedures in all handing, transfer
and storage operations. Before attempting to connect components to the test setup, make certain that the power supply is
OFF. Likewise, be sure the power supply is OFF before removing any component connected to the test setup.
(14) When the power supply, is turned on because of in certain cases, momentary Rash-current flow into the IC at the
logic unsettled, the couple capacitance, GND pattern of width and leading line must be considered.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
8/9
2009.05 - Rev.C
Technical Note
BD45□□□G, BD46□□□G series
 Part Number Selection
B
D
BD45:
4
2
5
3
1
-
G
T
R
Open Drain Type
Reset Voltage Value
Counter Timer
Package
Taping Specifications
CMOS Detector IC with
23: 2.3V
Delay Time Settings
G:SSOP5
Embossed Taping
Built-In Counter Timer
48: 4.8V
5: 50ms
1: 100ms
BD46:
2: 200ms
CMOS Output Type
CMOS Detector IC with
Built-In Counter Timer
SSOP5
<Dimension>
(Unit:mm)
2.9±0.2
1
2
0.2Min.
+0.2
4
1.6 −0.1
2.8±0.2
5
+6°
4° −4°
3
0.05±0.05
1.25Max.
1.1±0.05
0.13
<Tape and Reel information> SSOP5
Tape
Embossed carrier tape
Quantity
3000pcs
Direction
of feed
TR (The direction is the 1pin of product is at the upper left
when you hold reel on the left hand and you pull out the tape
on the right hand)
+0.05
−0.03
0.42 +0.05
−0.04
0.95
X X X
X X X
0.1
X X X
X X X
X X X
X X X
1Pin
X X X
X X X
X X X
X X X
Direction of feed
Reel
* When you order, please order in times the amount of package quantity.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
9/9
2009.05 - Rev.C
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039A
Similar pages