Rohm BDJ0650HFV Thermostat output temperature sensor ics with power down function Datasheet

Small and high accuracy Temperature Sensor IC Series High Accuracy detection
Thermostat Output
Temperature Sensor ICs
with Power Down Function
No.09047EAT05
BDJ□□□0HFV Series
●Description
BDJ□□□0HFV series is thermostat output temperature sensor IC with built-in temperature detection element,constant
current circuit,high-accuracy reference voltage source in one chip.Temperature detection can be realized at ±2.5℃
accuracy without complicated design.It is the best temperature sensor IC for a portable equipment of micro and low
current,the power down function, and the battery drive.It is possible to use it for a wide usage such as the heat detection
and temperature monitors because it provides with the analog output in addition to the thermostat power output.
BDJ□□□0HFV series has 8 types of model at 5℃ intervals from +55℃ to +90℃ temperature range.
●Features
1) Detection Temperature Range 55~90℃ by 5℃ Step 8 products.
2) Power supply Voltage range 2.4~5.5V.
3) High Accuracy thermostat ( typ.±1.0℃, max.±2.5℃ @Ta=55~90℃ )
4) High Accuracy Analog Output ( typ.±1.0℃, max.±2.5℃ @Ta=-30~100℃ )
5) Analog Output Temperature Sensitivity ( typ. -8.2mV/℃ )
6) Low Supply Current ( typ. 7.5μA )
7) Power down control function built in.(PD interface Voltage min 1.5V)
8) Small Package ( typ. 1.60mm×1.60mm×0.60mm )
9) Low thermal resistance package ( typ. 187℃/W )
10) ESD Rating 8kV ( HBM )
●Applications
Cell phone, Digital Camera,Thermal Protection for Electrical Equipment (NoteBook PC, FPD-TV, etc.)
●Line up matrix
BDJ0900HFV
90
BDJ0850HFV
85
BDJ0800HFV
80
BDJ0750HFV
75
Open
Drain
Open
Drain
Open
Drain
Open
Drain
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
Detect
Temp.
(℃)
Product
Name
Active L
fd
BDJ0700HFV
70
Active L
fe
BDJ0650HFV
65
Active L
ff
BDJ0600HFV
60
Active L
fg
BDJ0550HFV
55
OS Output
Format
1/9
OS Output
Format
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Marking
Detect
Temp.
(℃)
Marking
Product
Name
Active L
fh
Active L
fk
Active L
fm
Active L
fn
2009.08 - Rev.A
Technical Note
BDJ□□□0HFV Series
● ABSOLUTE MAXIMUM RATINGS ( Ta = 25℃ )
PARAMETERS
SYMBOL
Power Supply Voltage
VDD
Input Voltage ( PD )
VIN
OS terminal Voltage
VOS
OS terminal Current
IOS
Power dissipation
Pd
Storage Temperature Range
Tstg
LIMIT
-0.3 to 7.0*1
-0.3 to VDD+0.3
-0.3 to 7.0*1
5.0
536*2
-55 to 150
UNIT
V
V
V
mA
mW
℃
*1. Not to exceed Pd
*2. Reduced by 5.36mW for each increase in Ta of 1℃ over 25℃
( mounted on 70mm×70mm×1.6mm Glass-epoxy PCB )
● RECOMMENDED OPERATING CONDITION
PARAMETERS
SYMBOL
Power Supply Voltage
VDD
Operating Temperature Range
Topr
MIN.
2.4
-30
TYP.
2.8
-
MAX.
5.5
100
UNIT
V
℃
● ELECTRICAL CHARACTERISTICS ( unless otherwise specified, VDD = 2.8V, Ta = 25℃ )
PARAMETER
Supply Current
Normal function mode
Power Down mode
PD
Input L Voltage
Input H Voltage
PD Leakage Current
Analog Output
VTemp Output Voltage
VTemp Temperature Sensitivity
VTemp Load Regulation
Vtemp VDD Regulation
OS Output Open Drain
OS Leakage Current
OS Output Voltage
Radiation hardiness is not designed.
MIN.
LIMIT
TYP.
MAX.
IDD
IDDPD
-
7.5
0.3
12.0
1.0
μA
μA
PD="H"
PD="L"
VIL
VIH
ILPD
GND
1.5
-
-
0.2
VDD
1.0
V
V
μA
PD=2.8V
Vtemp
VSE
1.279
-8.00
1.300
-8.20
1.321
-8.40
V
mV/℃
⊿VtempRL
-
-
1.0
mV
⊿VtempVDD
-
-
4.0
mV
IL
VOL
-
-
1.0
0.4
μA
SYMBOL
UNIT
V
CONDITIONS
Ta = 30℃
Ta = -30 to 100℃
difference of
IOUT : 0μA / 2μA
VDD=2.4~5.5V
VOS =5.0V
IOS = 1.0mA
● TEMPERATURE ACCURACY ( unless otherwise specified, VDD = 2.8V )
PARAMETER
Thermostat
Sensing Temperature Accuracy
Sensing Temperature
Hysteresis
Analog Output
Vtemp Temperature Accuracy
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
SYMBOL
MIN.
LIMIT
TYP.
MAX.
UNIT
Tacc
-
±1.0
±2.5
℃
Thys
7.5
10.0
12.5
℃
Ttemp
-
±1.0
±2.5
℃
2/9
CONDITIONS
VDD = 2.8V
Ta = -30 to 100℃
2009.08 - Rev.A
Technical Note
BDJ□□□0HFV Series
● Block Diagram
Vtemp
1
GND
2
IRef
5
VDD
4
OS
VRef
TEMP
SENSOR
PD
3
PD
● PIN DESCRIPTION
PIN
NO.
PIN
NAME
1
Vtemp
2
GND
3
PD
4
OS
5
VDD
FUNCTION
Output voltage in inverse
proportion to the temperature
( TYP. -8.20mV/℃ )
GROUND
PD control
H : Normal function mode
L : Power Down mode
COMMENT
Set the OPEN state or connect high impedance
input node.(over 10MΩ)
"H" Thermostat and Analog output operation.
"L" Power Down state.
Open Drain Active L.
Use the pull-up resistor more than 10kΩ.
Digital thermostat output
POWER SUPPLY
● EQUIVALENT CIRCUIT
PD
OS
VDD
OS
PD
GND
Use the pull-up resistor more than 10kΩ.
GND
Vtemp
VDD
Vtemp
GND
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
3/9
2009.08 - Rev.A
Technical Note
BDJ□□□0HFV Series
● PACKAGE OUTLINES ( HVSOF5 )
MARKING
Lot No.
HVSOF5(UNIT:mm)
● Block Diagram
Please adjust Capacitor by
the noise condition of the
Vtemp
set.
VDD
IRef
1
0.1μF
GND
5
VRef
2
3
www.rohm.com
by the noise condition of the
set.
OS
PD
© 2009 ROHM Co., Ltd. All rights reserved.
Please adjust bypass Capacitor
+
-
TEMP
SENSOR
PD
1μF
4
4/9
Please pull-up over 10kΩfor OS output
terminal.
2009.08 - Rev.A
Technical Note
BDJ□□□0HFV Series
●Reference Data
2.0
15
Ta=30°C
Ta=30°C
1.5
Vtemp [V]
IDD [μA]
10
PD="H"
1.0
5
0.5
PD="L"
0
0.0
0
1
2
3
4
5
6
0
7
1
2
VDD [V]
5
6
7
Fig1. Supply Current(IDD) vs. Supply Voltage
Fig2. Vtemp Voltage vs. Supply Voltage
2.0
2
VDD=2.8V
0
1.5
-2
⊿Vtemp [mV]
Vtemp[V]
3
4
VDD [V]
1.0
-4
-6
-8
0.5
VDD=2.8V, Ta=30°C
-10
0.0
-40
-12
-20
0
20
40
Temp[℃]
60
80
100
0
1
2
3
4
5
Iout [uA]
Fig3. Vtemp Voltage vs. Temperature
Fig4. Vtemp Voltage vs. Output Current
0.8
VDD=2.8V, Ta=25°C
V OL[V]
0.6
0.4
0.2
0
0
1
2
3
IOS [mA]
4
5
Fig5. OS Output Voltage vs. Load Current
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
5/9
2009.08 - Rev.A
Technical Note
BDJ□□□0HFV Series
●Function Diagram(ex. 80℃ detect Active“L”type BDJ0800HFV)
Temperature sensor internal IC sense temperature, Vtemp terminal output voltage convert temperature.
Vtemp value is 1.300[V] at Ta = 30[℃].
The value of Vtemp voltage reduce reversely proportional temperature at rate of –8.2mV/℃.
OS Output Voltage( VOS ) [V]
Analog Temp. Sensor Output [V]
3.0
2.5
2.0
Vtemp@30℃
( 1.300V )
1.5
1.0
Temperature
Sensitivity
( -8.20mV/℃ typ.)
0.5
Vos
Detect point Temperature
Hysteresis
( 10℃ typ.)
0 0
-50
3
-30
-10
10
30
50
70
90
110
130
Temperature [℃]
If the temperature over detect temperature,
internal comparator operate OS output “H” to “L”.(ex.active “L” Type)
In case of OS return to “H”,the temperature 10℃ lower than detect temperature.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
6/9
2009.08 - Rev.A
Technical Note
BDJ□□□0HFV Series
●Operation Sequence
(ex.80℃ detect Active“L”type BDJ0800HFV)
VDD
H Level 1.5V
PD
L Level 0.2V
7.5µA
IDD
7.5µA
0.3µA
0.3µA
0.3µA
1.300V@Ta=30℃
Vtemp
OS
Hi Z
Ref Voltage
70°C
80°C
Hi Z
Hi Z(pull-up)
Hi Z
Hi Z
Hi Z
Hi Z
time
tOS_L
tOS_H
BDJ0800HFV operate start after PD“H”Input.
Please read OS terminal signal below wait time after PD ”H” Input.
Ta
Symbol
Wait time
Under detect Temp.
tOS_L
200µs
Over detect Temp.
tOS_H
1000µs
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
7/9
2009.08 - Rev.A
Technical Note
BDJ□□□0HFV Series
●Notes for use
1) Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can
break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any
special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety
measures including the use of fuses, etc.
2) GND voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
3) Pin short and mistake fitting
When mounting the IC on the PCB, pay attention to the orientation of the IC. If there is a placement mistake, the IC may be
burned up.
4) Operation in strong electric field
Be noted that using ICs in the strong electric field can malfunction them.
5) Mutual impedance
Use short and wide wiring tracks for the power supply and ground to keep the mutual impedance
as small as possible. Use a capacitor to keep ripple to a minimum.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
8/9
2009.08 - Rev.A
Technical Note
BDJ□□□0HFV Series
●Ordering part number
B
D
J
0
9
0
0
H
Detect Temp.
Series Name
090: 90℃ 070: 70℃
085: 85℃ 065: 65℃
080: 80℃ 060: 60℃
075: 75℃ 055: 55℃
F
V
Package : HVSOF5
T
R
TR=Reel-wound embossed taping
Output Format
0 : active
L
1 : active H
HVSOF5
Quantity
3000pcs
4
4
(0.91)
5
0.2MAX
Embossed carrier tape
(0.3)
(0.05)
Tape
1.0±0.05
5
(0.41)
1.6±0.05
(0.8)
Direction
of feed
TR
The direction is the 1pin of product is at the upper right when you hold
( reel on the left hand and you pull out the tape on the right hand
)
3 2 1
1 2 3
1pin
0.13±0.05
S
+0.03
0.02 –0.02
0.6MAX
1.2±0.05
(MAX 1.28 include BURR)
<Tape and Reel information>
1.6±0.05
0.1
S
0.5
0.22±0.05
0.08
Direction of feed
M
(Unit : mm)
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
Reel
9/9
∗ Order quantity needs to be multiple of the minimum quantity.
2009.08 - Rev.A
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039A
Similar pages