ILA1519 2 x 6 Watt Stereo Car Radio Power Amplifier GENERAL DESCRIPTION The ILA1519B is an integrated class-B dual output amplifier in a 9-lead single in-line (SIL) plastic medium power package. The device is primarily developed for car radio applications. FEATURES Requires very few external components Thermally protected High output power Reverse polarity safe Fixed gain Compatible with TDA1517 (except gain) Good ripple rejection No switch-on/switch-off plop Mute/stand-by switch Protected against electrostatic discharge Load dump protection AC and DC short-circuit-safe to ground and Vp Capability to handle high energy on outputs (Vp = 0 V) QUICK REFERENCE DATA PARAMETER Supply voltage range operating non-operating load dump protected Repetitive peak output current Total quiescent current Stand-by current Switch-on current Input impedance Output power Channel separation Noise output voltage Supply voltage ripple rejection CONDITIONS MIN. TYP. MAX. UNIT Vp Vp Vp 6,0 - 14,4 - 18,0 30 45 2,5 V V V A 40 0,1 80 100 40 mA mA mA kΩ W W dB µV dB IORM Itot Isb Isw /Z1/ 50 THD= 0,5%;4 Ω THD=10%;4 Ω f=100Hz f=1kHz to 10 kHz Crystal temperature SYMBOL 5 6 α Vno(rms) SVRR SVRR Tc 40 150 40 48 150 dB 0 C PACKAGE OUTLINE: 9-lead SIL-bent-to-DIL; plastic (SOT110B). PINNING 1 2 3 4 5 6 7 8 9 NV1 GND1 SVRR OUT1 GND2 OUT2 Vp M/SS INV2 non-inverting input 1 ground (signal) supply voltage ripple rejection output 1 ground (substrate) output 2 supply voltage mute/stand-by switch non-inverting input 2 1 INTEGRAL ILA1519 DC CHARACTERISTICS (note 1) o Vp = 14,4 V; Tamb = 25 C; unless otherwise specified PARAMETER CONDITIONS Supply Supply voltage range note 2 Quiescent current note 3 DC output voltage Vp IP VO 6,0 - Mute/stand-by switch Switch-on voltage level VON 8,5 SYMBOL MIN. TYP. 14,4 40 6,95 MAX. UNIT 18,0 80 - V mA V - V 6,4 V see Fig.3 Mute condition Output signal in mute position Vmute VI = 1 V (max.); f = 20 Hz to 15 kHz Stand-by condition DC current in stand-by condition Switch-on current 3,3 - VO Vsb Isb Isw - 20 mV 12 2 100 40 V µA µA min. typ. max. unit 4 5,5 - 5 6,0 0,1 - W W % 41 Hz kHz dB 75 dB dB dB dB kΩ 500 1 mV mV mV dB dB 0 - AC CHARACTERISTICS (note 1) o Vp=14,4V; RL=4Ω; f=1kHz; Tamb=25 C unless otherwise specified parameter conditions symbol Output power note 4; PO THD = 0,5% PO THD = 10% Total harmonic distortion THD PO=1W Low frequency roll-off note 5; -3 dB fL fH High frequency roll-off -1 dB GV Closed loop voltage gain Supply voltage ripple rejection note 6 ON f= 100 Hz SVRR ON f= 10 Hz to 10 kHz SVRR SVRR mute SVRR stand-by lZil Input impedance note 7; Noise output voltage Vno(rms) ON RS=0Ω Vno(rms) ON RS= 10 kΩ Vno(rms) a mute note 8 lDGvl Channel separation RS= 10 kΩ Channel balance 20 39 40 48 48 80 50 40 - 45 40 60 150 250 120 0,1 Notes to the characteristics 1. All characteristics are measured using the circuit shown in Fig. 4. 2. The circuit is DC adjusted at Vp= 6V to 18V and AC operating at Vp= 8,5V to 18 V. 3. At 18 V < Vp< 30 V the DC output voltage < Vp/2. 4. Output power is measured directly at the output pins of the IC. 5. Frequency response externally fixed. 6. Ripple rejection measured at the output with a source impedance of 0 ^ (maximum ripple amplitude of 2 V) and a frequency between 100 Hz and 10 kHz. 7. Noise voltage measured in a bandwidth of 20 Hz to 20 kHz. 8. Noise output voltage independent of R^ (V j = 0 V). 2 INTEGRAL