MOTOROLA 1N5913B

MOTOROLA
SEMICONDUCTOR
TECHNICAL DATA
GENERAL
DATA
1 to 3 Watt DO-41 Surmetic 30
Zener Voltage Regulator Diodes
1–3 WATT
DO-41
SURMETIC 30
GENERAL DATA APPLICABLE TO ALL SERIES IN
THIS GROUP
1 to 3 Watt Surmetic 30
Silicon Zener Diodes
1 TO 3 WATT
ZENER REGULATOR
DIODES
3.3–400 VOLTS
. . . a complete series of 1 to 3 Watt Zener Diodes with limits and operating characteristics
that reflect the superior capabilities of silicon-oxide-passivated junctions. All this in an
axial-lead, transfer-molded plastic package offering protection in all common environmental conditions.
Specification Features:
• Surge Rating of 98 Watts @ 1 ms
• Maximum Limits Guaranteed On Up To Six Electrical Parameters
• Package No Larger Than the Conventional 1 Watt Package
Mechanical Characteristics:
CASE: Void-free, transfer-molded, thermosetting plastic
FINISH: All external surfaces are corrosion resistant and leads are readily solderable
POLARITY: Cathode indicated by color band. When operated in zener mode, cathode
will be positive with respect to anode
MOUNTING POSITION: Any
WEIGHT: 0.4 gram (approx)
WAFER FAB LOCATION: Phoenix, Arizona
ASSEMBLY/TEST LOCATION: Seoul, Korea
CASE 59-03
DO-41
PLASTIC
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
DC Power Dissipation @ TL = 75°C
Lead Length = 3/8″
Derate above 75°C
PD
3
Watts
24
mW/°C
DC Power Dissipation @ TA = 50°C
Derate above 50°C
PD
1
6.67
Watt
mW/°C
TJ, Tstg
– 65 to +200
°C
Operating and Storage Junction Temperature Range
PD , MAXIMUM DISSIPATION (WATTS)
5
L = 1/8″
L = LEAD LENGTH
TO HEAT SINK
4
L = 3/8″
3
2
L = 1″
1
0
0
20
40
60
80 100 120 140 160
TL, LEAD TEMPERATURE (°C)
180
200
Figure 1. Power Temperature Derating Curve
Motorola TVS/Zener Device Data
1–3 Watt DO-41 Surmetic 30 Data Sheet
6-43
θJL (t, D) TRANSIENT THERMAL RESISTANCE
JUNCTION-TO-LEAD (° C/W)
GENERAL DATA — 1-3 WATT DO-41 SURMETIC 30
30
20
10
7
5
3
2
1
0.7
0.5
D =0.5
0.2
0.1
t2
DUTY CYCLE, D =t1/t2
0.02
0.01
NOTE: BELOW 0.1 SECOND, THERMAL
RESPONSE CURVE IS APPLICABLE
TO ANY LEAD LENGTH (L).
D=0
0.3
0.0001 0.0002
t1
PPK
0.05
0.0005
0.001
0.002
0.005
0.01
0.02
0.05
t, TIME (SECONDS)
0.1
0.2
SINGLE PULSE ∆TJL = θJL (t)PPK
REPETITIVE PULSES ∆TJL = θJL (t,D)PPK
0.5
1
2
5
10
Figure 2. Typical Thermal Response L, Lead Length = 3/8 Inch
IR , REVERSE LEAKAGE (µ Adc) @ VR
AS SPECIFIED IN ELEC. CHAR. TABLE
PPK , PEAK SURGE POWER (WATTS)
1K
RECTANGULAR
NONREPETITIVE
WAVEFORM
TJ = 25°C PRIOR
TO INITIAL PULSE
500
300
200
100
50
30
20
10
0.1
0.2 0.3 0.5
1
2 3
5
10
PW, PULSE WIDTH (ms)
20 30 50
100
Figure 3. Maximum Surge Power
3
2
1
0.5
TA = 125°C
0.2
0.1
0.05
0.02
0.01
0.005
0.002
0.001
0.0005
0.0003
TA = 125°C
1
2
5
10
20
50 100
NOMINAL VZ (VOLTS)
200
400
1000
Figure 4. Typical Reverse Leakage
APPLICATION NOTE
Since the actual voltage available from a given zener diode
is temperature dependent, it is necessary to determine junction temperature under any set of operating conditions in order
to calculate its value. The following procedure is recommended:
Lead Temperature, TL, should be determined from:
TL = θLA PD + TA
θLA is the lead-to-ambient thermal resistance (°C/W) and
PD is the power dissipation. The value for θLA will vary and
depends on the device mounting method. θLA is generally
30–40°C/W for the various clips and tie points in common
use and for printed circuit board wiring.
The temperature of the lead can also be measured using a
thermocouple placed on the lead as close as possible to the tie
point. The thermal mass connected to the tie point is normally
large enough so that it will not significantly respond to heat
surges generated in the diode as a result of pulsed operation
once steady-state conditions are achieved. Using the measured value of TL, the junction temperature may be determined by:
TJ = TL + ∆TJL
1–3 Watt DO-41 Surmetic 30 Data Sheet
6-44
∆TJL is the increase in junction temperature above the lead
temperature and may be found from Figure 2 for a train of
power pulses (L = 3/8 inch) or from Figure 10 for dc power.
∆TJL = θJL PD
For worst-case design, using expected limits of IZ, limits of
PD and the extremes of TJ (∆TJ) may be estimated. Changes
in voltage, VZ, can then be found from:
∆V = θVZ ∆TJ
θVZ, the zener voltage temperature coefficient, is found from
Figures 5 and 6.
Under high power-pulse operation, the zener voltage will
vary with time and may also be affected significantly by the
zener resistance. For best regulation, keep current excursions
as low as possible.
Data of Figure 2 should not be used to compute surge capability. Surge limitations are given in Figure 3. They are lower
than would be expected by considering only junction temperature, as current crowding effects cause temperatures to be extremely high in small spots resulting in device degradation
should the limits of Figure 3 be exceeded.
Motorola TVS/Zener Device Data
GENERAL DATA — 1-3 WATT DO-41 SURMETIC 30
TEMPERATURE COEFFICIENT RANGES
10
8
6
4
RANGE
2
0
–2
–4
3
4
5
6
7
8
9
10
VZ, ZENER VOLTAGE @ IZT (VOLTS)
11
12
θ VZ, TEMPERATURE COEFFICIENT (mV/ °C) @ IZT
θ VZ, TEMPERATURE COEFFICIENT (mV/ °C) @ I ZT
(90% of the Units are in the Ranges Indicated)
1000
500
200
100
50
20
10
10
20
50
100
200
400
VZ, ZENER VOLTAGE @ IZT (VOLTS)
Figure 5. Units To 12 Volts
1000
Figure 6. Units 10 To 400 Volts
ZENER VOLTAGE versus ZENER CURRENT
100
50
30
20
50
30
20
IZ , ZENER CURRENT (mA)
IZ, ZENER CURRENT (mA)
(Figures 7, 8 and 9)
100
10
5
3
2
1
0.5
0.3
0.2
0.1
0
1
2
3
4
5
6
7
VZ, ZENER VOLTAGE (VOLTS)
8
9
10
10
5
3
2
1
0.5
0.3
0.2
0.1
0
10
10
IZ , ZENER CURRENT (mA)
5
2
1
0.5
0.2
0.1
100
150
200
250
300
350
VZ, ZENER VOLTAGE (VOLTS)
Figure 9. VZ = 100 thru 400 Volts
Motorola TVS/Zener Device Data
30
40
50
60
70
80
VZ, ZENER VOLTAGE (VOLTS)
90
100
Figure 8. VZ = 12 thru 82 Volts
400
θJL, JUNCTION-TO-LEAD THERMAL RESISTANCE (° C/W)
Figure 7. VZ = 3.3 thru 10 Volts
20
80
70
60
50
L
40
L
30
TL
20
PRIMARY PATH OF
CONDUCTION IS THROUGH
THE CATHODE LEAD
10
0
0
1/8
1/4
3/8
1/2
5/8
3/4
L, LEAD LENGTH TO HEAT SINK (INCH)
7/8
1
Figure 10. Typical Thermal Resistance
1–3 Watt DO-41 Surmetic 30 Data Sheet
6-45
GENERAL DATA — 1-3 WATT DO-41 SURMETIC 30
*MAXIMUM RATINGS
Rating
Symbol
Value
Unit
DC Power Dissipation @ TL = 75°C, Lead Length = 3/8″
Derate above 75°C
PD
1.5
12
Watts
mW/°C
*ELECTRICAL CHARACTERISTICS (TL = 30°C unless otherwise noted. VF = 1.5 Volts Max @ lF = 200 mAdc for all types.)
Motorola
Type
Number
(Note 1)
Nominal
Zener Voltage
VZ @ IZT
Volts
(Note 2 and 3)
Test
Current
IZT
mA
ZZT @ IZT
Ohms
ZZK
Ohms
1N5913B
1N5914B
1N5915B
1N5916B
1N5917B
3.3
3.6
3.9
4.3
4.7
113.6
104.2
96.1
87.2
79.8
10
9
7.5
6
5
1N5918B
1N5919B
1N5920B
1N5921B
1N5922B
5.1
5.6
6.2
6.8
7.5
73.5
66.9
60.5
55.1
50
1N5923B
1N5924B
1N5925B
1N5926B
1N5927B
8.2
9.1
10
11
12
1N5928B
1N5929B
1N5930B
1N5931B
1N5932B
Max. Zener Impedance (Note 4)
Max. Reverse
Leakage Current
IZK
mA
IR
µA
500
500
500
500
500
1
1
1
1
1
100
75
25
5
5
1
1
1
1
1.5
454
416
384
348
319
4
2
2
2.5
3
350
250
200
200
400
1
1
1
1
0.5
5
5
5
5
5
2
3
4
5.2
6
294
267
241
220
200
45.7
41.2
37.5
34.1
31.2
3.5
4
4.5
5.5
6.5
400
500
500
550
550
0.5
0.5
0.25
0.25
0.25
5
5
5
1
1
6.5
7
8
8.4
9.1
182
164
150
136
125
13
15
16
18
20
28.8
25
23.4
20.8
18.7
7
9
10
12
14
550
600
600
650
650
0.25
0.25
0.25
0.25
0.25
1
1
1
1
1
9.9
11.4
12.2
13.7
15.2
115
100
93
83
75
1N5933B
1N5934B
1N5935B
1N5936B
1N5937B
22
24
27
30
33
17
15.6
13.9
12.5
11.4
17.5
19
23
26
33
650
700
700
750
800
0.25
0.25
0.25
0.25
0.25
1
1
1
1
1
16.7
18.2
20.6
22.8
25.1
68
62
55
50
45
1N5938B
1N5939B
1N5940B
1N5941B
1N5942B
36
39
43
47
51
10.4
9.6
8.7
8
7.3
38
45
53
67
70
850
900
950
1000
1100
0.25
0.25
0.25
0.25
0.25
1
1
1
1
1
27.4
29.7
32.7
35.8
38.8
41
38
34
31
29
1N5943B
1N5944B
1N5945B
1N5946B
1N5947B
56
62
68
75
82
6.7
6
5.5
5
4.6
86
100
120
140
160
1300
1500
1700
2000
2500
0.25
0.25
0.25
0.25
0.25
1
1
1
1
1
42.6
47.1
51.7
56
62.2
26
24
22
20
18
@
@ VR
Volts
Maximum DC
Zener
Current
IZM
mAdc
(continued)
*Indicates JEDEC Registered Data.
1–3 Watt DO-41 Surmetic 30 Data Sheet
6-46
Motorola TVS/Zener Device Data
GENERAL DATA — 1-3 WATT DO-41 SURMETIC 30
*ELECTRICAL CHARACTERISTICS — continued (TL = 30°C unless otherwise noted. VF = 1.5 Volts Max @ lF = 200 mAdc for all
types.)
Motorola
Type
Number
(Note 1)
Nominal
Zener Voltage
VZ @ IZT
Volts
(Note 2 and 3)
Test
Current
IZT
mA
ZZT @ IZT
Ohms
ZZK
Ohms
1N5948B
1N5949B
1N5950B
1N5951B
1N5952B
91
100
110
120
130
4.1
3.7
3.4
3.1
2.9
200
250
300
380
450
1N5953B
1N5954B
1N5955B
1N5956B
150
160
180
200
2.5
2.3
2.1
1.9
600
700
900
1200
Max. Zener Impedance (Note 4)
Max. Reverse
Leakage Current
IZK
mA
IR
µA
3000
3100
4000
4500
5000
0.25
0.25
0.25
0.25
0.25
1
1
1
1
1
69.2
76
83.6
91.2
98.8
16
15
13
12
11
6000
6500
7000
8000
0.25
0.25
0.25
0.25
1
1
1
1
114
121.6
136.8
152
10
9
8
7
@
@ VR
Volts
Maximum DC
Zener
Current
IZM
mAdc
*Indicates JEDEC Registered Data.
NOTE 1. TOLERANCE AND VOLTAGE DESIGNATION
Tolerance designation — Device tolerances of ±5% are indicated by a “B” suffix.
Nominal zener voltages between those shown and ±1% and ±2% tight voltage tolerances.
Consult factory.
NOTE 2. SPECIAL SELECTIONS AVAILABLE INCLUDE:
Motorola TVS/Zener Device Data
1–3 Watt DO-41 Surmetic 30 Data Sheet
6-47
GENERAL DATA — 1-3 WATT DO-41 SURMETIC 30
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) VF = 1.5 V Max, IF = 200 mA for all types)
Motorola
Type No.
(Note 1)
Nominal
Zener Voltage
VZ @ IZT
Volts
(Note 2)
Test
Current
IZT
mA
Maximum
Zener
Current
IZM
mA
Surge
Current
@ TA = 25°C
ir – mA
(Note 4)
ZZT @ IZT
Ohms
ZZK @ IZK
Ohms
IZK
mA
3EZ3.9D5
3EZ4.3D5
3EZ4.7D5
3EZ5.1D5
3.9
4.3
4.7
5.1
192
174
160
147
4.5
4.5
4
3.5
400
400
500
550
1
1
1
1
80
30
20
5
1
1
1
1
630
590
550
520
4.4
4.1
3.8
3.5
3EZ5.6D5
3EZ6.2D5
3EZ6.8D5
3EZ7.5D5
5.6
6.2
6.8
7.5
134
121
110
100
2.5
1.5
2
2
600
700
700
700
1
1
1
0.5
5
5
5
5
2
3
4
5
480
435
393
360
3.3
3.1
2.9
2.66
3EZ8.2D5
3EZ9.1D5
3EZ10D5
3EZ11D5
8.2
9.1
10
11
91
82
75
68
2.3
2.5
3.5
4
700
700
700
700
0.5
0.5
0.25
0.25
5
3
3
1
6
7
7.6
8.4
330
297
270
245
2.44
2.2
2
1.82
3EZ12D5
3EZ13D5
3EZ14D5
3EZ15D5
12
13
14
15
63
58
53
50
4.5
4.5
5
5.5
700
700
700
700
0.25
0.25
0.25
0.25
1
0.5
0.5
0.5
9.1
9.9
10.6
11.4
225
208
193
180
1.66
1.54
1.43
1.33
3EZ16D5
3EZ17D5
3EZ18D5
3EZ19D5
16
17
18
19
47
44
42
40
5.5
6
6
7
700
750
750
750
0.25
0.25
0.25
0.25
0.5
0.5
0.5
0.5
12.2
13
13.7
14.4
169
159
150
142
1.25
1.18
1.11
1.05
3EZ20D5
3EZ22D5
3EZ24D5
3EZ27D5
20
22
24
27
37
34
31
28
7
8
9
10
750
750
750
750
0.25
0.25
0.25
0.25
0.5
0.5
0.5
0.5
15.2
16.7
18.2
20.6
135
123
112
100
1
0.91
0.83
0.74
3EZ28D5
3EZ30D5
3EZ33D5
3EZ36D5
28
30
33
36
27
25
23
21
12
16
20
22
750
1000
1000
1000
0.25
0.25
0.25
0.25
0.5
0.5
0.5
0.5
21
22.5
25.1
27.4
96
90
82
75
0.71
0.67
0.61
0.56
3EZ39D5
3EZ43D5
3EZ47D5
3EZ51D5
39
43
47
51
19
17
16
15
28
33
38
45
1000
1500
1500
1500
0.25
0.25
0.25
0.25
0.5
0.5
0.5
0.5
29.7
32.7
35.6
38.8
69
63
57
53
0.51
0.45
0.42
0.39
3EZ56D5
3EZ62D5
3EZ68D5
3EZ75D5
56
62
68
75
13
12
11
10
50
55
70
85
2000
2000
2000
2000
0.25
0.25
0.25
0.25
0.5
0.5
0.5
0.5
42.6
47.1
51.7
56
48
44
40
36
0.36
0.32
0.29
0.27
3EZ82D5
3EZ91D5
3EZ100D5
3EZ110D5
82
91
100
110
9.1
8.2
7.5
6.8
95
115
160
225
3000
3000
3000
4000
0.25
0.25
0.25
0.25
0.5
0.5
0.5
0.5
62.2
69.2
76
83.6
33
30
27
25
0.24
0.22
0.2
0.18
3EZ120D5
3EZ130D5
3EZ140D5
3EZ150D5
120
130
140
150
6.3
5.8
5.3
5
300
375
475
550
4500
5000
5000
6000
0.25
0.25
0.25
0.25
0.5
0.5
0.5
0.5
91.2
98.8
106.4
114
22
21
19
18
0.16
0.15
0.14
0.13
3EZ160D5
3EZ170D5
3EZ180D5
3EZ190D5
160
170
180
190
4.7
4.4
4.2
4
625
650
700
800
6500
7000
7000
8000
0.25
0.25
0.25
0.25
0.5
0.5
0.5
0.5
121.6
130.4
136.8
144.8
17
16
15
14
0.12
0.12
0.11
0.1
Max Zener Impedance
(Note 3)
Leakage
Current
IR @ VR
Volts
µA Max
(continued)
1–3 Watt DO-41 Surmetic 30 Data Sheet
6-48
Motorola TVS/Zener Device Data
GENERAL DATA — 1-3 WATT DO-41 SURMETIC 30
ELECTRICAL CHARACTERISTICS — continued (TA = 25°C unless otherwise noted) VF = 1.5 V Max, IF = 200 mA for all types)
Motorola
Type No.
(Note 1)
Nominal
Zener Voltage
VZ @ IZT
Volts
(Note 2)
Test
Current
IZT
mA
ZZT @ IZT
Ohms
ZZK @ IZK
Ohms
IZK
mA
3EZ200D5
3EZ220D5
3EZ240D5
3EZ270D5
200
220
240
270
3.7
3.4
3.1
2.8
875
1600
1700
1800
8000
9000
9000
9000
0.25
0.25
0.25
0.25
0.5
1
1
1
3EZ300D5
3EZ330D5
3EZ360D5
3EZ400D5
300
330
360
400
2.5
2.3
2.1
1.9
1900
2200
2700
3500
9000
9000
9000
9000
0.25
0.25
0.25
0.25
1
1
1
1
Max Zener Impedance
(Note 3)
NOTE 1. TOLERANCES
Suffix 5 indicates 5% tolerance. Any other tolerance will be considered as a special device.
NOTE 2. ZENER VOLTAGE (VZ) MEASUREMENT
Motorola guarantees the zener voltage when measured at 40 ms ±10 ms 3/8″ from the diode
body, and an ambient temperature of 25°C (+8°C, –2°C)
NOTE 3. ZENER IMPEDANCE (Z Z) DERIVATION
The zener impedance is derived from the 60 cycle ac voltage, which results when an ac current having an rms value equal to 10% of the dc zener current (IZT or IZK) is superimposed
on IZT or IZK.
Maximum
Zener
Current
IZM
mA
Surge
Current
@ TA = 25°C
ir – mA
(Note 4)
152
167
182
205
13
12
11
10
0.1
0.09
0.09
0.08
228
251
274
304
9
8
8
7
0.07
0.06
0.06
0.06
Leakage
Current
IR @ VR
Volts
µA Max
NOTE 3. ZENER VOLTAGE (VZ) MEASUREMENT
Motorola guarantees the zener voltage when meausred at 90 seconds while maintaining the
lead temperature (TL) at 30°C ±1°C, 3/8″ from the diode body.
NOTE 4. ZENER IMPEDANCE (Z Z) DERIVATION
The zener impedance is derived from the 60 cycle ac voltage, which results when an ac current having an rms value equal to 10% of the dc zener current (IZT or IZK) is superimposed
on IZT or IZK.
NOTE 4. SURGE CURRENT (i r) NON-REPETITIVE
The rating listed in the electrical characteristics table is maximum peak, non-repetitive, reverse surge current of 1/2 square wave or equivalent sine wave pulse of 1/120 second duration superimposed on the test current, IZT, per JEDEC standards, however, actual device capability is as described in Figure 3 of General Data sheet for Surmetic 30s.
NOTE 5. SPECIAL SELECTIONS AVAILABLE INCLUDE:
Nominal zener voltages between those shown. Tight voltage tolerances such as ±1% and
±2%. Consult factory.
Motorola TVS/Zener Device Data
1–3 Watt DO-41 Surmetic 30 Data Sheet
6-49
GENERAL DATA — 1-3 WATT DO-41 SURMETIC 30
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted.) VF = 1.5 V Max, IF = 200 mA for all types.
Type No.
(Note 1)
Min
Max
Test
Current
IZT
mA
MZD3.9
MZD4.3
MZD4.7
MZD5.1
MZD5.6
3.7
4
4.4
4.8
5.2
4.1
4.6
5
5.4
6
MZD6.2
MZD6.8
MZD7.5
MZD8.2
MZD9.1
5.8
6.4
7
7.7
8.5
MZD10
MZD11
MZD12
MZD13
MZD15
Zener Voltage
(Note 2)
Zener Impedance at IZT
f = 1000 Hz (Ohm)
Surge Current
@ TL = 25°C
ir – mA
(Note 3)
Typ
Max
Blocking Voltage
IR = 1 µA
Typical
TC
%/°C
100
100
100
100
100
3.8
3.8
3.8
2
1
7
7
7
5
2
—
—
—
—
1.5
–0.06
+0.055
+0.03
+0.03
+0.038
1380
1260
1190
1070
970
6.6
7.2
7.9
8.7
9.6
100
100
100
100
50
1
1
1
1
2
2
2
2
2
4
1.5
2
2
3.5
3.5
+0.045
+0.05
+0.058
+0.062
+0.068
890
810
730
660
605
9.4
10.4
11.4
12.4
13.8
10.6
11.6
12.7
14.1
15.8
50
50
50
50
50
2
4
4
5
5
4
7
7
10
10
5
5
7
7
10
+0.075
+0.076
+0.077
+0.079
+0.082
550
500
454
414
380
MZD16
MZD18
MZD20
MZD22
MZD24
15.3
16.8
18.8
20.8
22.8
17.1
19.1
21.2
23.3
25.6
25
25
25
25
25
6
6
6
6
7
15
15
15
15
15
10
10
10
12
12
+0.083
+0.085
+0.086
+0.087
+0.088
344
304
285
250
225
MZD27
MZD30
MZD33
MZD36
MZD39
25.1
28
31
34
37
28.9
32
35
38
41
25
25
25
10
10
7
8
8
21
21
15
15
15
40
40
14
14
17
17
20
+0.09
+0.091
+0.092
+0.093
+0.094
205
190
170
150
135
MZD43
MZD47
MZD51
MZD56
MZD62
40
44
48
52
58
46
50
54
60
66
10
10
10
10
10
24
24
25
25
25
45
45
60
60
80
20
24
24
28
28
+0.095
+0.095
+0.096
+0.096
+0.097
125
115
110
95
90
MZD68
MZD75
MZD82
MZD91
MZD100
64
70
77
85
94
72
79
88
96
106
10
10
10
5
5
25
30
30
60
60
80
100
100
200
200
34
34
41
41
50
+0.097
+0.098
+0.098
+0.099
+0.11
80
70
65
60
55
MZD110
MZD120
MZD130
MZD150
MZD160
104
114
124
138
153
116
127
141
156
171
5
5
5
5
5
80
80
110
110
150
250
250
300
300
350
50
60
60
75
75
+0.11
+0.11
+0.11
+0.11
+0.11
50
45
—
—
—
MZD180
MZD200
168
188
191
212
5
5
150
150
350
350
90
90
+0.11
+0.11
—
—
NOTE 1. TOLERANCE AND TYPE NUMBER DESIGNATION
The type numbers listed have zener voltage min/max limits as shown.
NOTE 2. ZENER VOLTAGE (VZ) MEASUREMENT
The zener voltage is measured after the test current (IZT) has been applied for 40 ±10 milliseconds, while maintaining a lead temperautre (TL) of 30°C at a point of 10 mm from the diode
body.
1–3 Watt DO-41 Surmetic 30 Data Sheet
6-50
NOTE 3. (ir) NON-REPETITIVE SURGE CURRENT
Maximum peak, non-repetitive reverse surge current of half square wave or equivalent sine
wave pulse of 50 ms duration, superimposed on the test current (IZT).
NOTE 4. SPECIAL SELECTIONS AVAILABLE INCLUDE:
Nominal zener voltages between those shown. Tight voltage tolerances such as ±1% and
±2%. Consult factory.
Motorola TVS/Zener Device Data
GENERAL DATA — 1-3 WATT DO-41 SURMETIC 30
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) VF = 1.5 V Max, lF = 200 mA for all types
Motorola
Type No.
(Note 1)
Nominal
Zener Voltage
VZ @ IZT
Volts
(Note 2)
VR
Volts
Surge
Current
@ TA = 25°C
ir – mA
(Note 4)
Test Current
IZT
mA
ZZT @ IZT
Ohms
ZZK @ IZK
Ohms
IZK
mA
MZP4728A
MZP4729A
MZP4730A
MZP4731A
MZP4732A
3.3
3.6
3.9
4.3
4.7
76
69
64
58
53
10
10
9
9
8
400
400
400
400
500
1
1
1
1
1
100
100
50
10
10
1
1
1
1
1
1380
1260
1190
1070
970
MZP4733A
MZP4734A
MZP4735A
MZP4736A
MZP4737A
5.1
5.6
6.2
6.8
7.5
49
45
41
37
34
7
5
2
3.5
4
550
600
700
700
700
1
1
1
1
0.5
10
10
10
10
10
1
2
3
4
5
890
810
730
660
605
MZP4738A
MZP4739A
MZP4740A
MZP4741A
MZP4742A
8.2
9.1
10
11
12
31
28
25
23
21
4.5
5
7
8
9
700
700
700
700
700
0.5
0.5
0.25
0.25
0.25
10
10
10
5
5
6
7
7.6
8.4
9.1
550
500
454
414
380
MZP4743A
MZP4744A
MZP4745A
MZP4746A
MZP4747A
13
15
16
18
20
19
17
15.5
14
12.5
10
14
16
20
22
700
700
700
750
750
0.25
0.25
0.25
0.25
0.25
5
5
5
5
5
9.9
11.4
12.2
13.7
15.2
344
304
285
250
225
MZP4748A
MZP4749A
MZP4750A
MZP4751A
MZP4752A
22
24
27
30
33
11.5
10.5
9.5
8.5
7.5
23
25
35
40
45
750
750
750
1000
1000
0.25
0.25
0.25
0.25
0.25
5
5
5
5
5
16.7
18.2
20.6
22.8
25.1
205
190
170
150
135
MZP4753A
MZP4754A
MZP4755A
MZP4756A
MZP4757A
36
39
43
47
51
7
6.5
6
5.5
5
50
60
70
80
95
1000
1000
1500
1500
1500
0.25
0.25
0.25
0.25
0.25
5
5
5
5
5
27.4
29.7
32.7
35.8
38.8
125
115
110
95
90
MZP4758A
MZP4759A
MZP4760A
MZP4761A
MZP4762A
56
62
68
75
82
4.5
4
3.7
3.3
3
110
125
150
175
200
2000
2000
2000
2000
3000
0.25
0.25
0.25
0.25
0.25
5
5
5
5
5
42.6
47.1
51.7
56
62.2
80
70
65
60
55
MZP4763A
MZP4764A
1M110ZS5
1M120ZS5
1M130ZS5
91
100
110
120
130
2.8
2.5
2.3
2
1.9
250
350
450
550
700
3000
3000
4000
4500
5000
0.25
0.25
0.25
0.25
0.25
5
5
5
5
5
69.2
76
83.6
91.2
98.8
50
45
—
—
—
1M150ZS5
1M160ZS5
1M180ZS5
1M200ZS5
150
160
180
200
1.7
1.6
1.4
1.2
1000
1100
1200
1500
6000
6500
7000
8000
0.25
0.25
0.25
0.25
5
5
5
5
114
121.6
136.8
152
—
—
—
—
Max Zener Impedance
(Note 3)
NOTE 1. TOLERANCE AND TYPE NUMBER DESIGNATION
The type numbers listed have a standard tolerance on the nominal zener voltage of ±5%. The
tolerance on the 1M type numbers is indicated by the digits following ZS in the part number.
“5” indicates a ±5% VZ tolerance.
NOTE 2. ZENER VOLTAGE (VZ) MEASUREMENT
Motorola guarantees the zener voltage when measured at 90 seconds while maintaining the
lead temperature (TL) at 30°C ±1°C, 3/8″ from the diode body.
NOTE 3. ZENER IMPEDANCE (Z Z) DERIVATION
The zener impedance is derived from the 60 cycle ac voltage, which results when an ac
Motorola TVS/Zener Device Data
Leakage
Current
IR
@
µA Max
current having an rms value equal to 10% of the dc zener current (IZT or IZK) is superimposed
on IZT or IZK.
NOTE 4. SURGE CURRENT (i r) NON-REPETITIVE
The rating listed in the electrical characteristics table is maximum peak, non-repetitive,
reverse surge current of 1/2 square wave or equivalent sine wave pulse of 1/120 second
duration superimposed on the test current, IZT, however, actual device capability is as
described in Figure 3 of General Data — Surmetic 30.
NOTE 5. SPECIAL SELECTIONS AVAILABLE INCLUDE:
Nominal zener voltages between those shown. Tight voltage tolerances such as ±1% and
±2%. Consult factory.
1–3 Watt DO-41 Surmetic 30 Data Sheet
6-51
GENERAL DATA — 1-3 WATT DO-41 SURMETIC 30
Zener Voltage Regulator Diodes — Axial Leaded
1–3 Watt DO-41 Surmetic 30
B
NOTES:
1. ALL RULES AND NOTES ASSOCIATED WITH
JEDEC DO-41 OUTLINE SHALL APPLY.
2. POLARITY DENOTED BY CATHODE BAND.
3. LEAD DIAMETER NOT CONTROLLED WITHIN F
DIMENSION.
D
K
F
DIM
A
B
D
F
K
A
F
K
MILLIMETERS
MIN
MAX
4.07
5.20
2.04
2.71
0.71
0.86
—
1.27
27.94
—
INCHES
MIN
MAX
0.160 0.205
0.080 0.107
0.028 0.034
—
0.050
1.100
—
CASE 59-03
DO-41
PLASTIC
(Refer to Section 10 for Surface Mount, Thermal Data and Footprint Information.)
MULTIPLE PACKAGE QUANTITY (MPQ)
REQUIREMENTS
Package Option
Type No. Suffix
MPQ (Units)
Tape and Reel
RL
6K
Tape and Ammo
TA
4K
(Refer to Section 10 for more information on Packaging Specifications.)
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
Literature Distribution Centers:
USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036.
EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England.
JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan.
ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong.
1–3 Watt DO-41 Surmetic 30 Data ◊Sheet
6-52
Motorola TVS/Zener Device Data