MAXIM MAX3454EETE

19-2924; Rev 4; 2/06
±15kV ESD-Protected USB Transceivers
The MAX3453E–MAX3456E ±15kV ESD-protected USBcompliant transceivers interface low-voltage ASICs with
USB devices. The devices fully comply with USB 1.1
and USB 2.0 when operating at full (12Mbps) and low
(1.5Mbps) speeds. The MAX3453E–MAX3456E operate
with VL as low as +1.65V, ensuring compatibility with
low-voltage ASICs.
The MAX3453E–MAX3456E feature a logic-selectable
suspend mode that reduces current consumption to
less than 40µA. Integrated ±15kV ESD protection protects the USB D+ and D- bidirectional bus connections.
The MAX3453E supports only full-speed (12Mbps)
operation. The MAX3453E/MAX3454E feature an internal 1.5kΩ USB pullup resistor and an enumeration function that allows devices to logically disconnect while
plugged in. The MAX3453E/MAX3455E provide a pushpull bus-detect (BD) output that asserts high when
VBUS > +4.0V.
The MAX3453E–MAX3456E operate over the extended
temperature range (-40°C to +85°C) and are available
in 14-pin TSSOP and 16-pin (3mm x 3mm) thin QFN
packages.
Applications
PDAs
PC Peripherals
Cellular Telephones
Features
♦ ±15kV ESD Protection on D+ and D♦ USB 1.1 and USB 2.0 (Low-Speed and Full-Speed)Compliant Transceivers
♦ Combined VP and VM Inputs/Outputs
♦ +1.65V to +3.6V VL Logic Supply Input for
Interfacing with Low-Voltage ASICs
♦ Enumerate Input Function (MAX3453E/MAX3454E)
♦ Powered from Li+ Battery as Low as +3.1V
(MAX3454E/MAX3456E)
♦ VBUS Detection (MAX3453E/MAX3455E)
♦ Internal Pullup Resistor (MAX3453E/MAX3454E)
♦ No Power-Supply Sequencing Required
Ordering Information
PART
TEMP RANGE PIN-PKG
o
PKG CODE
o
MAX3453EEUD
-40 C to +85 C 14 TSSOP
MAX3453EETE
-40oC to +85oC 16 Thin QFN
MAX3454EEUD
-40oC to +85oC 14 TSSOP
MAX3454EETE
-40oC to +85oC 16 Thin QFN
MAX3455EEUD
-40oC to +85oC 14 TSSOP
o
U14-1
T1633-4
U14-1
T1633-4
U14-1
o
MAX3455EETE
-40 C to +85 C 16 Thin QFN
Data Cradles
MAX3456EEUD
-40oC to +85oC 14 TSSOP
MP3 Players
MAX3456EETE
-40oC to +85oC 16 Thin QFN
T1633-4
U14-1
T1633-4
Selector Guide
PART
VBUS POWERSUPPLY
VOLTAGE (V)
VL POWERSUPPLY
VOLTAGE (V)
INTERNAL
PULLUP
RESISTOR
VBUS LEVEL
DETECT
MAX3453E
4.0 to 5.5
1.65 to 3.6
Yes
Yes
MAX3454E
3.0 to 5.5
1.65 to 3.6
Yes
No
MAX3455E
4.0 to 5.5
1.65 to 3.6
No
Yes
MAX3456E
3.0 to 5.5
1.65 to 3.6
No
No
USB SPEED
SUPPORTED
±15kV ESD
PROTECTION
Yes
Full
Yes
Yes
Low/full
Yes
No
Low/full
Yes
No
Low/full
Yes
ENUMERATE
Typical Operating Circuit appears at end of data sheet.
Pin Configurations appear at end of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX3453E–MAX3456E
General Description
MAX3453E–MAX3456E
±15kV ESD-Protected USB Transceivers
ABSOLUTE MAXIMUM RATINGS
VBUS, VL, D+, D- to GND.......................................-0.3V to +6.0V
VTRM to GND ............................................-0.3V to (VBUS + 0.3V)
VP, VM, SUS, ENUM, SPD,
RCV, OE, BD to GND ................................-0.3V to (VL + 0.3V)
Current (into any pin) ........................................................±15mA
Short-Circuit Current (D+ and D-)...................................±150mA
Continuous Power Dissipation (TA = +70°C)
14-Pin TSSOP (derate 9.1mW/°C above +70°C) .........727mW
16-Pin Thin QFN (derate 14.7mW/°C above +70°C)....1176mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VBUS = +4.0V to +5.5V or VTRM = +3.0V to +3.6V, VL = +1.65V to +3.6V, TA = TMIN to TMAX, unless otherwise noted. Typical values
are at VBUS = +5.0V, VL = +2.5V, and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
3.0
3.3
3.6
V
SUPPLY INPUTS (VBUS, VTRM, VL)
Regulated Supply Voltage Output
VTRM
Internal regulator
Operating Supply Current
IVBUS
Full-speed transmitting and receiving at
12Mbps, CL = 50pF on D+ and D- (Note 2)
10
mA
Full-speed transmitting and receiving at
12Mbps (Note 2)
2.5
mA
Operating VL Supply Current
IVL
Full-Speed Idle and SE0 Supply
Current
IVBUS(IDLE)
Static VL Supply Current
IVL(STATIC)
Suspend Supply Current
Full-speed idle: VD+ > 2.7V, VD- < 0.3V
250
350
SE0: VD+ < 0.3V, VD- < 0.3V
250
350
Full-speed idle,
SE0, or suspend
mode
MAX3453E/MAX3455E
15
MAX3454E/MAX3456E
5
µA
MAX3453E
(ENUM = low),
VM = VP = open, MAX3455E
IVBUS(SUSP)
SUS = OE = high MAX3454E
(ENUM = low),
MAX3456E
Disable Mode Supply Current
Sharing Mode VL Supply Current
D+/D- Sharing Mode Load
Current
D+/D- Disable Mode Load
Current
2
IVBUS(DIS)
VL = GND or open
VBUS = GND or
open, OE = low,
IVL(SHARING) VP = low or high,
VM = low or
high, SUS = high
40
µA
35
20
MAX3453E/MAX3455E
µA
20
µA
MAX3454E/MAX3456E
ID_(SHARING) VBUS = GND or open, VD_ = 0 or +5.5V
ID_(DIS)
µA
VL = GND or open, VD_ = 0 or +5.5V
_______________________________________________________________________________________
5
20
µA
5
µA
±15kV ESD-Protected USB Transceivers
(VBUS = +4.0V to +5.5V or VTRM = +3.0V to +3.6V, VL = +1.65V to +3.6V, TA = TMIN to TMAX, unless otherwise noted. Typical values
are at VBUS = +5.0V, VL = +2.5V, and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX3453E/MAX3455E, supply lost
MAX3453E/MAX3455E, supply present
USB Power-Supply Detection
Threshold
VTH_VBUS
USB Power-Supply Detection
Hysteresis
VHYST_VBUS
VL Power-Supply Detection
Threshold
UNITS
3.6
4.0
MAX3454E/MAX3456E, supply lost
MAX3454E/MAX3456E, supply present
(Note 3)
MAX
0.8
V
3.6
MAX3453E/MAX3455E
40
MAX3454E/MAX3456E
75
mV
0.85
VTH_VL
V
DIGITAL INPUTS/OUTPUTS (VP, VM, RCV, SUS, OE, SPD, BD, ENUM)
VIL
VM, VP, SUS, SPD, ENUM, OE
Input-Voltage High
VIH
VM, VP, SUS, SPD, ENUM, OE
Output-Voltage Low
VOL
VM, VP, RCV, BD, IOL = +2mA
Output-Voltage High
VOH
VM, VP, RCV, BD, IOH = -2mA
Input Leakage Current
ILKG
Input Capacitance
CIN
Measured from input to GND
Differential Input Sensitivity
VID
|VD+ - VD-|
0.2
Differential Common-Mode
Voltage
VCM
Includes VID range
0.8
Input-Voltage Low
0.3 x VL
V
0.4
V
0.7 x VL
V
VL - 0.4
V
-1
+1
10
µA
pF
ANALOG INPUTS/OUTPUTS (D+, D-)
Single-Ended Input Low Voltage
VILSE
Single-Ended Input High Voltage
VIHSE
Hysteresis
VHYST
0.8
VOLD
RL = 1.5kΩ to +3.6V
VOHD
RL = 15kΩ to GND
ILZ
V
-1
+1
µA
CIND
Measured from D_ to GND
Steady-state drive
3.5
Driver off
10
ILOAD = 500µA (MAX3453E/MAX3454E)
(Note 4)
V
3.6
ZDRV
RPULLUP
mV
0.3
Driver Output Impedance
Internal Pullup Resistance
V
2.8
Transceiver Capacitance
ZIN
V
V
250
Output-Voltage High
Input Impedance
2.5
2.0
Output-Voltage Low
Off-State Leakage Current
V
20
pF
15.5
Ω
MΩ
1.425
1.575
kΩ
ESD PROTECTION (D+, D-)
Human Body Model
±15
kV
IEC 61000-4-2 Contact Discharge
±8
kV
_______________________________________________________________________________________
3
MAX3453E–MAX3456E
DC ELECTRICAL CHARACTERISTICS (continued)
MAX3453E–MAX3456E
±15kV ESD-Protected USB Transceivers
TIMING CHARACTERISTICS
(VBUS = +4.0V to +5.5V or VTRM = +3.0V to +3.6V, VL = +1.65V to +3.6V, TA = TMIN to TMAX, unless otherwise noted. Typical values
are at VBUS = +5V, VL = +2.5V, and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DRIVER CHARACTERISTICS (Full-Speed Mode, CL = 50pF)
Rise Time
tFR
10% to 90% of |VOHD - VOLD|, Figures 1, 6
4
20
ns
Fall Time
tFF
90% to 10% of |VOHD - VOLD|, Figures 1, 6
4
20
ns
Rise/Fall-Time Matching (Note 2)
tFR / tFF
Excluding the first transition from idle state,
Figures 1, 6
90
110
%
Output-Signal Crossover Voltage
(Note 2)
VCRS_F
Excluding the first transition from idle state,
Figures 2, 6
1.3
2.0
V
Driver Propagation Delay
Driver Disable Delay
Driver Enable Delay
tPLH_DRV
Low-to-high transition, Figures 2, 6
18
tPHL_DRV
High-to-low transition, Figures 2, 6
18
tPHZ_DRV
High-to-off transition, Figure 3
20
ns
tPLZ_DRV
Low-to-off transition, Figure 3
20
ns
tPZH_DRV
Off-to-high transition, Figure 3
20
ns
tPZL_DRV
Off-to-low transition, Figure 3
20
ns
ns
DRIVER CHARACTERISTICS (low-speed mode, CL = 200pF to 600pF, MAX3454E/MAX3455E/MAX3456E)
Rise Time
tLR
10% to 90% of |VOHD - VOLD|, Figures 1, 6
75
300
ns
Fall Time
tLF
90% to 10% of |VOHD - VOLD|, Figures 1, 6
75
300
ns
Rise/Fall-Time Matching
tLR / tLF
Excluding the first transition from idle state,
Figures 1, 6
80
125
%
Output-Signal Crossover Voltage
VCRS_L
Excluding the first transition from idle state,
Figures 2, 6
1.3
2.0
V
RECEIVER CHARACTERISTICS (CL = 15pF)
tPLH_RCV
Low-to-high transition, Figures 4, 6
22
tPHL_RCV
High-to-low transition, Figures 4, 6
22
Single-Ended Receiver
Propagation Delay
tPLH_SE
Low-to-high transition, Figures 4, 6
12
tPHL_SE
High-to-low transition, Figures 4, 6
12
Single-Ended Receiver Disable
Delay
tPHZ_SE
High-to-off transition, Figure 5
15
tPLZ_SE
Low-to-off transition, Figure 5
15
Single-Ended Receiver Enable
Delay
tPZH_SE
Off-to-high transition, Figure 5
15
tPZL_SE
Off-to-low transition, Figure 5
15
Differential Receiver Propagation
Delay
Note 1:
Note 2:
Note 3:
Note 4:
4
ns
ns
ns
ns
Parameters are 100% production tested at +25°C, unless otherwise noted. Limits over temperature are guaranteed by design.
Guaranteed by design, not production tested.
Production tested to +2.7V for VL < +3.0V.
Including external 27Ω series resistor.
_______________________________________________________________________________________
±15kV ESD-Protected USB Transceivers
SINGLE-ENDED RECEIVER
PROPAGATION DELAY vs. VL
MAX3453E-56E toc02
MAX3453E-56E toc01
8
CL = 15pF
7
TA = +25°C
6
TA = +85°C
MAX3453E-56E toc03
CL = 50pF
CL = 400pF
5
D+/D1V/div
4
D+/D1V/div
TA = -40°C
3
2
1
0
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6
20ns/div
100ns/div
SUPPLY CURRENT
vs. D+/D- CAPACITANCE
LOGIC SUPPLY CURRENT
vs. D+/D- CAPACITANCE
MAX3453E-56E toc04
24
22
VP
2V/div
VM
2V/div
OE
5V/div
20ns/div
MAX3453E-56E toc05
CL = 15pF
20
18
16
14
12
10
8
6
4
SPD = VL, fIN = 6MHz
2
0
SPD = GND, fIN = 750kHz
500
450
LOGIC SUPPLY CURRENT (µA)
OE, VP, VM TIMING
SPD = VL, fIN = 6MHz
400
350
300
250
200
150
100
50
SPD = GND, fIN = 750kHz
0
0
50
100 150 200 250 300 350 400
D+/D- CAPACITANCE (pF)
MAX3453E-56E toc06
VL (V)
SUPPLY CURRENT (mA)
PROPAGATION DELAY (ns)
RISE-/FALL-TIME MATCHING
(LOW SPEED)
RISE-/FALL-TIME MATCHING
(FULL SPEED)
0
50
100 150 200 250 300 350 400
D+/D- CAPACITANCE (pF)
_______________________________________________________________________________________
5
MAX3453E–MAX3456E
Typical Operating Characteristics
(VBUS = +5.0V, VL = +3.3V, TA = +25°C, unless otherwise noted.)
±15kV ESD-Protected USB Transceivers
MAX3453E–MAX3456E
Pin Description
PIN
MAX3454E/
MAX3455E/
MAX3456E
NAME
TSSOP
THIN QFN
TSSOP
THIN QFN
1
15
1
15
VL
FUNCTION
Digital I/O Connections Logic Supply. Connect a +1.65V to
+3.6V supply to VL. Bypass VL to GND with a 0.1µF ceramic
capacitor.
2
1
—
—
SPD
Speed Selector Input. Connect SPD to GND to select the lowspeed data rate (1.5Mbps). Connect SPD to VL to select the fullspeed data rate (12Mbps). The MAX3453E only supports fullspeed operation.
3
2
3
2
RCV
Differential Receiver Output. RCV responds to the differential inputs
on D+ and D- (see Tables 3, 4). RCV asserts low if SUS = VL.
4
3
4
3
VP
Receiver Output/Driver Input. VP functions as a receiver output
when OE = VL. VP duplicates D+ when receiving. VP functions
as a driver input when OE = GND.
5
4
5
4
VM
Receiver Output/Driver Input. VM functions as a receiver output
when OE = VL. VM duplicates D- when receiving. VM functions
as a driver input when OE = GND.
6, 13*
5, 8, 13*, 16
6
5, 8, 16
N.C.
No Connection. Not internally connected.
*Pin 13 is No Connection for MAX3456E only.
7
6
7
6
GND
Ground
8
7
8
7
SUS
Suspend Input. Drive SUS low for normal operation. Drive SUS
high to put the MAX3453E–MAX3456E into suspend mode. RCV
asserts low in suspend mode. VP and VM remain active in
suspend mode.
9
9
9
9
OE
Output Enable. Drive OE to GND to enable the transmitter
outputs. Drive OE to VL to disable the transmitter outputs. OE
also controls the I/O direction of VP and VM (see Tables 3, 4).
D-
USB Input/Output. For OE = GND, D- functions as a USB
output, with VM providing the input signal. For OE = VL, Dfunctions as a USB input, with VM functioning as a single-ended
receiver output. Connect a 1.5kΩ resistor from D- to VTRM for
low-speed (1.5Mbps) operation (MAX3455E/MAX3456E). Drive
ENUM to VL to connect the internal 1.5kΩ resistor from D- to
VTRM for low-speed (MAX3454E, SPD = GND) operation.
10
6
MAX3453E
10
10
10
_______________________________________________________________________________________
±15kV ESD-Protected USB Transceivers
PIN
MAX3454E/
MAX3455E/
MAX3456E
TSSOP
11
12
MAX3453E
THIN QFN
11
12
13
13
(MAX3455E (MAX3455E
only)
only)
13
13
(MAX3454E (MAX3454E
only)
only)
14
14
TSSOP
11
NAME
FUNCTION
D+
USB Input/Output. For OE = GND, D+ functions as a USB
output, with VP providing the input signal. For OE = VL, D+
functions as a USB input, with VP functioning as a single-ended
receiver output. Connect a 1.5kΩ resistor from D+ to VTRM for
full-speed (12Mbps) operation (MAX3455E/MAX3456E). Drive
ENUM to VL to connect the internal 1.5kΩ resistor (MAX3453E/
MAX3454E) from D+ to VTRM for full-speed (MAX3454E, SPD =
VL) operation.
Internal Regulator Output. VTRM provides a regulated +3.3V
output. Bypass VTRM to GND with a 1µF (min) ceramic
capacitor as close to the device as possible. VTRM normally
derives power from VBUS. Alternatively, drive VTRM directly with
a +3.3V ±10% supply (MAX3454E/MAX3456E). VTRM provides
power to internal circuitry and provides the pullup voltage for an
external USB pullup resistor (MAX3455E/MAX3456E). Do not
use VTRM to power external circuitry.
THIN QFN
11
12
12
VTRM
13
13
BD
2
14
1
14
Bus-Detection Output (MAX3453E/MAX3455E). The push-pull
BD output asserts low and the device enters sharing mode if
VBUS < +3.6V. BD asserts high if VBUS > +4.0V.
ENUM
Enumerate Function Selection Input (MAX3453E/MAX3454E).
Drive ENUM to VL to connect the internal 1.5kΩ resistor
between VTRM and D+ or D-, depending on the state of SPD.
Drive ENUM to GND to disconnect the internal 1.5kΩ resistor.
For SPD = VL, the 1.5kΩ resistor connects to D+. For SPD =
GND, the 1.5kΩ resistor connects to D-. For the MAX3453E, the
resistor only connects to D+.
VBUS
USB Power-Supply Input. Connect a +4.0V to +5.5V power
supply to VBUS. VBUS provides power to the internal linear
regulator. Bypass VBUS to GND with a 0.1µF ceramic capacitor
as close to the device as possible. Connect VBUS and VTRM
together when powering the MAX3454E/MAX3456E with an
external power supply (+3.3V ±10%).
_______________________________________________________________________________________
7
MAX3453E–MAX3456E
Pin Description (continued)
±15kV ESD-Protected USB Transceivers
MAX3453E–MAX3456E
Functional Diagram
MAX3453E
TO INTERNAL
CIRCUITRY
BD
LDO
REGULATOR
VTH_VBUS
VBUS
VTRM
VL
VP
D+
D-
VM
OE
LEVEL
TRANSLATOR
RCV
SUS
TO INTERNAL
CIRCUITRY
1.5kΩ
VTRM
ENUM
GND
8
_______________________________________________________________________________________
±15kV ESD-Protected USB Transceivers
MAX3454E–
MAX3456E
TO INTERNAL
CIRCUITRY
MAX3455E ONLY
BD
LDO
REGULATOR
VTH_VBUS
VBUS
VTRM
VL
SPD
VP
D+
D-
VM
OE
LEVEL
TRANSLATOR
RCV
SUS
TO INTERNAL
CIRCUITRY
MAX3454E ONLY
1.5kΩ
VTRM
SPD
ENUM
CONTROL
LOGIC
GND
_______________________________________________________________________________________
9
MAX3453E–MAX3456E
Functional Diagram (continued)
MAX3453E–MAX3456E
±15kV ESD-Protected USB Transceivers
Detailed Description
The MAX3453E–MAX3456E USB-compliant transceivers
convert single-ended or differential logic-level signals to
USB signals, and USB signals to single-ended or differential logic-level signals. The MAX3453E fully complies
with full-speed (12Mbps) operation under USB specification 2.0. The MAX3454E–MAX3456E fully comply with
USB specification 1.1, and full-speed (12Mbps) and lowspeed (1.5Mbps) operation under USB specification 2.0.
The MAX3453E–MAX3456E operate with VL as low as
+1.65V, ensuring compatibility with low-voltage ASICs.
The MAX3453E–MAX3456E derive power from the USB
host (V BUS ) or from a single-cell Li+ battery
(MAX3454E/MAX3456E) connected to VBUS or from a
+3.3V regulated supply connected to VBUS and VTRM.
The MAX3453E–MAX3456E meet the physical layer
specifications for logic-level supply voltages (VL) from
+1.65V to +3.6V. Integrated ±15kV ESD protection safeguards the D+ and D- USB I/O ports.
The MAX3453E/MAX3454E feature an enumerate function providing an internal 1.5kΩ pullup resistor from D+
(MAX3453E/MAX3454E) or D- (MAX3454E only) to
VTRM. The enumerate function disconnects the 1.5kΩ
pullup resistor, allowing the MAX3453E/MAX3454E to
simulate a bus disconnect while powered and connected to the USB cable. The MAX3453E/MAX3455E feature a bus-detect output (BD) that asserts high if VBUS
> +4V. BD asserts low if V BUS < +3.6V. The
MAX3455E/MAX3456E require external pullup resistors
from either D+ or D- to VTRM to utilize the appropriate
bus speed. The MAX3456E is pin-for-pin compatible
with the Micrel MIC2550A.
Applications Information
Power-Supply Configurations
Normal Operating Mode
Connect VL and VBUS to system power supplies (Table 1).
Connect VL to a +1.65V to +3.6V supply. Connect VBUS
to a +4.0V to +5.5V supply. Alternatively, the MAX3454E/
MAX3456E can derive power from a single Li+ battery.
Connect the battery to VBUS.
Additionally, the MAX3454E/MAX3456E can derive
power from a +3.3V ±10% voltage regulator. Connect
VBUS and VTRM to an external +3.3V voltage regulator.
VBUS no longer consumes current to power the internal
linear regulator in this configuration.
Table 1. Power-Supply Configurations
VBUS (V)
VTRM (V)
VL (V)
CONFIGURATION
NOTES
4.0 to 5.5
3.0 to 3.6 output
1.65 to 3.6
Normal mode
—
3.1 to 4.5
3.0 to 3.6 output
1.65 to 3.6
Battery supply
MAX3454E/MAX3456E
3.0 to 3.6
3.0 to 3.6 input
1.65 to 3.6
Voltage regulator supply
MAX3454E/MAX3456E
GND or floating
High-Z
1.65 to 3.6
Sharing mode
Table 2
3.0 to 5.5
High-Z
GND or floating
Disable mode
Table 2
Table 2. Disable-Mode and Sharing-Mode Connections
INPUTS/OUTPUTS
VBUS/VTRM
VL
D+ and D-
DISABLE MODE
SHARING MODE
+3.0V to +5.5V / High Impedance
• Floating or connected to GND
(MAX3453E/MAX3454E/MAX3456E) / High Impedance
• < 3.6V (MAX3453E/MAX3455E) / High Impedance
Floating or connected to GND
1.65V to 3.6V input
High impedance
High impedance
High impedance for OE = low
VP and VM
Invalid*
RCV
Invalid*
Undefined**
High impedance
High impedance
Invalid*
Low
SPD (MAX3454E–MAX3456E),
SUS, OE, ENUM
(MAX3453E/MAX3454E)
BD (MAX3453E/MAX3455E)
High for OE = high
*High impedance or low.
**High or low.
10
______________________________________________________________________________________
±15kV ESD-Protected USB Transceivers
Sharing Mode
Connect VL to a system power supply and leave VBUS
(or VBUS and VTRM) unconnected or connect to GND.
D+ and D- enter a tri-state mode, allowing other circuitry
to share the USB D+ and D- lines, and VL consumes less
than 20µA of supply current. D+ and D- withstand
external signals up to +5.5V in sharing mode (Table 2).
Device Control
OE
OE controls the direction of communication. Drive OE
low to transfer data from the logic side to the USB side.
For OE = low, VP and VM serve as differential driver
inputs to the USB transmitter.
Drive OE high to transfer data from the USB side to the
logic side. For OE = high, VP and VM serve as singleended receiver outputs from the USB inputs
(D+ and D-). RCV serves as a differential receiver output, regardless of the state of OE.
ENUM (MAX3453E/MAX3454E)
The MAX3453E/MAX3454E feature an enumerate function that allows software control of USB enumeration.
USB protocol requires a 1.5kΩ pullup resistor to D+ or
D- to indicate the transmission speed to the host (see
the SPD section). The MAX3453E/MAX3454E provide
an internal 1.5kΩ pullup resistor. Disconnect the pullup
resistor from the circuit to simulate the removal of a
device from the USB. Drive ENUM low to disconnect
the internal pullup resistor. Drive ENUM high to connect
the internal pullup resistor. The SPD state (MAX3454E
only) determines whether the pullup resistor connects
to D+ or D-. For ENUM = high, the internal pullup resistor connects to D+ when SPD = VL (full speed) or to Dwhen SPD = GND (low speed). The MAX3453E only
supports full-speed operation; therefore, the pullup
resistor only connects to D+ or is disconnected.
tFR, tLR
tFF, tLF
VOHD
90%
10%
VOLD
90%
10%
Table 3a. Transmit Truth Table
(OE = 0, SUS = 0)
INPUTS
OUTPUTS
OUTPUT STATE
VP
VM
D+
D-
RCV
0
0
0
0
X
SE0
0
1
0
1
0
Logic 0
1
0
1
0
1
Logic 1
1
1
1
1
X
Undefined
X = Undefined.
Table 3b. Transmit Truth Table
(OE = 0, SUS = 1)
INPUTS
OUTPUTS
OUTPUT STATE
VP
VM
D+
D-
RCV
0
0
0
0
0
SE0
0
1
0
1
0
Logic 0
1
0
1
0
0
Logic 1
1
1
1
1
0
Undefined
Table 4a. Receive Truth Table
(OE = 1 and SUS = 0)
INPUTS
OUTPUTS
OUTPUT STATE
D+
D-
VP
VM
RCV
0
0
0
0
X
SE0
0
1
0
1
0
Logic 0
1
0
1
0
1
Logic 1
1
1
1
1
X
Undefined
X = Undefined.
Table 4b. Receive Truth Table
(OE = 1 and SUS = 1)
INPUTS
OUTPUTS
OUTPUT STATE
D+
D-
VP
VM
RCV
0
0
0
0
0
SE0
0
1
0
1
0
Logic 0
1
0
1
0
0
Logic 1
1
1
1
1
0
Undefined
Figure 1. Rise and Fall Times
______________________________________________________________________________________
11
MAX3453E–MAX3456E
Disable Mode
Connect VBUS to a system power supply and leave VL
unconnected or connect to GND. D+ and D- enter a tristate mode and VBUS (or VBUS and VTRM) consumes
less than 20µA of supply current. D+ and D- withstand
external signals up to +5.5V in disable mode (Table 2).
MAX3453E–MAX3456E
±15kV ESD-Protected USB Transceivers
SPD (MAX3454E/MAX3455E/MAX3456E)
SPD sets the transceiver speed. Connect SPD to GND
to select the low-speed data rate (1.5Mbps). Connect
SPD to VL to select the full-speed data rate (12Mbps).
The MAX3454E provides an internal pullup resistor for
selecting the bus speed. The MAX3455E and
MAX3456E require an external pullup resistor to D+ or
D- to set the bus speed. Connect the 1.5kΩ resistor
between D+ and VTRM to set the full-speed (12Mbps)
data rate, or connect the 1.5kΩ resistor between D- and
VTRM to set the low-speed (1.5Mbps) data rate.
VP AND VM RISE/FALL TIMES < 4ns
VM
VP
tPLH_DRV
tPHL_DRV
D-
SUS
The SUS state determines whether the MAX3453E–
MAX3456E operate in normal mode or in suspend
mode. Connect SUS to GND to enable normal operation. Drive SUS high to enable suspend mode. RCV
asserts low and VP and VM remain active in suspend
mode (Tables 3 and 4). Supply current decreases in
suspend mode (see the Electrical Characteristics).
BD (MAX3453E/MAX3455E)
The push-pull bus detect (BD) output monitors VBUS
and asserts high if V BUS is greater than +4.0V. BD
asserts low if V BUS is less than +3.6V and the
MAX3453E/MAX3455E enters sharing mode (Table 2).
VTRM
An internal linear regulator generates the VTRM voltage
(+3.3V, typ). VTRM derives power from VBUS (see the
Power-Supply Configurations section). VTRM powers the
internal portions of the USB circuitry and provides the
pullup voltage for an external USB pullup resistor
(MAX3455E/MAX3456E). Bypass VTRM to GND with a
1µF ceramic capacitor as close to the device as possible.
Do not use VTRM to provide power to external circuitry.
D+ and DD+ and D- serve as bidirectional bus connections and
are ESD protected to ±15kV (Human Body Model). For
OE = low, D+ and D- serve as transmitter outputs. For
OE = high, D+ and D- serve as receiver inputs.
VBUS
For most applications, VBUS connects to the VBUS terminal on the USB connector (see the Power-Supply
Configurations section). VBUS can also connect to an
external supply as low as +3.1V (MAX3454E/MAX3456E).
Drive VBUS low to enable sharing mode. Bypass VBUS to
GND with a 0.1µF ceramic capacitor as close to the
device as possible.
12
VCRS_F , VCRS_L
D+
Figure 2. Timing of VP and VM to D+ and D-
External Components
External Resistors
Proper USB operation requires two external resistors,
each 27Ω ±1%, 1/8W (or greater). Install one resistor in
series between D+ of the MAX3453E–MAX3456E and
D+ on the USB connector. Install the other resistor in
series between D- of the MAX3453E–MAX3456E and Don the USB connector (see Typical Operating Circuit).
The MAX3455E/MAX3456E require an external 1.5kΩ
pullup resistor between VTRM and D+ or D- to set the
bus speed.
External Capacitors
The MAX3453E–MAX3456E require three external
capacitors for proper operation. Bypass VL to GND with a
0.1µF ceramic capacitor. Bypass VBUS to GND with a
0.1µF ceramic capacitor. Bypass VTRM to GND with a
1µF (min) ceramic capacitor. Install all capacitors as
close to the device as possible.
Data Transfer
Transmitting Data to the USB
The MAX3453E–MAX3456E transmit data to the USB
differentially on D+ and D-. VP and VM serve as differential input signals to the driver (Tables 3a and 3b).
Receiving Data from the USB
To receive data from the USB, drive OE high and SUS
low. Differential data received by D+ and D- appears
as a differential logic signal at RCV. Single-ended
receivers on D+ and D- drive VP and VM, respectively
(Tables 4a and 4b).
______________________________________________________________________________________
±15kV ESD-Protected USB Transceivers
OE
VP/VM CONNECTED TO GND,
D+/D- CONNECTED TO PULLUP
D+/D- CONNECTED TO GND,
VP/VM CONNECTED TO PULLUP
D+/DVP/VM
tPLZ_DRV
tPZL_DRV
tPLZ_SE
VP/VM CONNECTED TO VL,
D+/D- CONNECTED TO PULLDOWN
OE
tPZL_SE
D+/D- CONNECTED TO +3V,
VP/VM CONNECTED TO PULLDOWN
OE
VP/VM
D+/D-
tPHZ_DRV
tPHZ_SE
tPZH_DRV
Figure 3. Enable and Disable Timing, Driver
tPZH_SE
Figure 5. Enable and Disable Timing, Receiver
INPUT RISE/FALL TIME < 4ns
+3V
TEST
POINT
MAX3453E–
MAX3456E
D+/D-
RCV, VM,
AND VP
0V
CL
(a) LOAD FOR RCV, VM, AND VP
MAX3453E–
MAX3456E
VL
tPLH_RCV,
tPLH_SE
27Ω
TEST
POINT
D+ AND DCL
RCV, VM, AND VP
tPHL_RCV,
tPHL_SE
Figure 4. Timing of D+ and D- to RCV, VM, and VP
15kΩ
(b) LOAD FOR D+/D-
Figure 6. Test Circuits
______________________________________________________________________________________
13
MAX3453E–MAX3456E
OE
MAX3453E–MAX3456E
±15kV ESD-Protected USB Transceivers
ESD Protection
D+ and D- possess extra protection against static electricity to protect the devices up to ±15kV. The ESD
structures withstand high ESD in all operating modes:
normal operation, suspend mode, and powered down.
D+ and D- provide protection to the following limits:
• ±15kV using the Human Body Model
• ±8kV using the Contact Discharge method specified
in IEC 61000-4-2
RC
1MΩ
CHARGE-CURRENTLIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
Cs
100pF
RD
1.5kΩ
DISCHARGE
RESISTANCE
DEVICE
UNDER
TEST
STORAGE
CAPACITOR
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, test methodology, and test results.
Figure 7. Human Body ESD Test Models
Human Body Model
Figure 7 shows the Human Body Model and Figure 8
shows the current waveform generated when discharged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of interest, which then discharges into the test device through
a 1.5kΩ resistor.
IP 100%
90%
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
AMPERES
36.8%
10%
0
IEC 61000-4-2
The IEC 61000-4-2 standard covers ESD testing and
performance of finished equipment. It does not specifically refer to integrated circuits. The major difference
between tests done using the Human Body Model and
IEC 61000-4-2 is a higher peak current in IEC 61000-42, due to lower series resistance. Hence, the ESD withstand voltage measured to IEC 61000-4-2 generally is
lower than that measured using the Human Body
Model. Figure 9 shows the IEC 61000-4-2 model. The
Contact Discharge method connects the probe to the
device before the probe is charged.
Ir
0
tRL
TIME
tDL
CURRENT WAVEFORM
Figure 8. Human Body Model Current Waveform
RC
50MΩ to 100MΩ
CHARGE-CURRENTLIMIT RESISTOR
RD
330Ω
DISCHARGE
RESISTANCE
Machine Model
The Machine Model for ESD tests all connections using
a 200pF storage capacitor and zero discharge resistance. Its objective is to emulate the stress caused by
contact that occurs with handling and assembly during
manufacturing. All pins require this protection during
manufacturing, not just inputs and outputs. After PC
board assembly, the Machine Model is less relevant to
I/O ports.
HIGHVOLTAGE
DC
SOURCE
Cs
150pF
STORAGE
CAPACITOR
Figure 9. IEC 61000-4-2 ESD Test Model
Chip Information
TRANSISTOR COUNT: 873
PROCESS: BiCMOS
14
______________________________________________________________________________________
DEVICE
UNDER
TEST
±15kV ESD-Protected USB Transceivers
+1.65V TO +3.6V
0.1µF
0.1µF
PC
VL(I/O)
BD*
VL
USB
POWER
VBUS
27Ω 1%
D+
D+
VP
27Ω 1%
VM
ASIC
RCV
MAX3453E
MAX3454E
D-
D-
GND
GND
USB CABLE
ENUM
15kΩ
15kΩ
SUS
VTRM
SPD**
1µF
OE
GND
*MAX3453E ONLY.
**MAX3454E ONLY.
+1.65V TO +3.6V
0.1µF
0.1µF
PC
VL(I/O)
VL
VP
VBUS
VM
VTRM
USB
POWER
1µF
RCV
ASIC
BD**
MAX3455E
MAX3456E*
1.5kΩ***
27Ω 1%
D+
D+
SUS
27Ω 1%
D-
SPD
OE
GND
D-
GND
GND
USB CABLE
15kΩ
15kΩ
*PIN COMPATIBLE WITH MICREL MIC2550A.
**MAX3455E ONLY.
***CONNECT TO D+ FOR FULL-SPEED OPERATION. CONNECT TO D- FOR LOW-SPEED OPERATION.
______________________________________________________________________________________
15
MAX3453E–MAX3456E
Typical Operating Circuits
±15kV ESD-Protected USB Transceivers
MAX3453E–MAX3456E
Pin Configurations
TOP VIEW
VL
1
14 VBUS
ENUM
2
13 BD
SPD 2
RCV
3
12 VTRM
RCV 3
VP
4
11 D+
VP 4
VM
5
10 D-
VM 5
10 D-
N.C.
6
9
OE
N.C. 6
9 OE
GND
7
8
SUS
GND 7
8 SUS
MAX3453E
14 VBUS
VL 1
13 N.C. (ENUM*) (BD**)
MAX3454E
MAX3455E
MAX3456E
TSSOP
2
VP
3
N.C.
VL
VBUS
BD
N.C.
VL
VBUS
N.C.
(ENUM*)
(BD**)
16
15
14
13
16
15
14
13
MAX3453E
12 VTRM
SPD
1
11 D+
RCV
2
10 D-
VP
3
12 VTRM
MAX3454E
MAX3455E
MAX3456E
10 D-
***EXPOSED PADDLE
***EXPOSED PADDLE
4
4
9
6
7
8
5
N.C.
VM
N.C.
N.C.
5
OE
SUS
9
GND
VM
11 D+
3mm x 3mm
THIN QFN
6
7
8
N.C.
RCV
TSSOP
SUS
1
11 D+
GND
ENUM
12 VTRM
OE
3mm x 3mm
THIN QFN
*MAX3454E ONLY.
**MAX3455E ONLY.
***CONNECT EXPOSED PADDLE TO GND OR LEAVE FLOATING.
16
______________________________________________________________________________________
±15kV ESD-Protected USB Transceivers
12x16L QFN THIN.EPS
(NE - 1) X e
E
MARKING
E/2
D2/2
(ND - 1) X e
D/2
AAAA
e
CL
D
D2
k
CL
b
0.10 M C A B
E2/2
L
E2
0.10 C
CL
CL
0.08 C
A
A2
A1
L
L
e
e
PACKAGE OUTLINE
8, 12, 16L THIN QFN, 3x3x0.8mm
21-0136
G
1
2
______________________________________________________________________________________
17
MAX3453E–MAX3456E
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
MAX3453E–MAX3456E
±15kV ESD-Protected USB Transceivers
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
PKG
12L 3x3
8L 3x3
16L 3x3
EXPOSED PAD VARIATIONS
REF. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX.
A
0.70
0.75
0.80
0.70
0.75
0.80
0.70
0.75
0.80
b
0.25
0.30 0.35
0.20
0.25 0.30
0.20 0.25
0.30
D
2.90
3.00
2.90
3.00
2.90 3.00
3.10
E
e
2.90 3.00 3.10
0.65 BSC.
2.90 3.00 3.10
0.50 BSC.
2.90 3.00 3.10
0.50 BSC.
L
0.35
0.45
0.30
0.55
3.10
0.75
0.55
3.10
0.65
0.40
N
8
12
16
ND
2
3
4
NE
2
A1
0
A2
k
0.25
0.02
4
3
0.05
0.20 REF
-
0
0.25
0.02
0.50
0.05
0.20 REF
-
0
0.25
0.02
0.05
0.20 REF
-
PKG.
CODES
D2
MIN.
NOM.
E2
MAX.
MIN.
NOM. MAX.
PIN ID
JEDEC
DOWN
BONDS
ALLOWED
TQ833-1
0.25
0.70
1.25
0.25
0.70
1.25
0.35 x 45¡
WEEC
T1233-1
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45¡
WEED-1
NO
T1233-3
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45¡
WEED-1
YES
YES
NO
T1233-4
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45¡
WEED-1
T1633-1
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45¡
WEED-2
NO
T1633-2
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45¡
WEED-2
YES
T1633F-3
0.65
0.80
0.95
0.65
0.80
0.95
0.225 x 45¡
WEED-2
N/A
T1633FH-3
0.65
0.80
0.95
0.65
0.80
0.95
0.225 x 45¡
WEED-2
N/A
T1633-4
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45¡
WEED-2
NO
NOTES:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
N IS THE TOTAL NUMBER OF TERMINALS.
THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO
JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED
WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE.
DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.20 mm AND 0.25 mm
FROM TERMINAL TIP.
ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
DRAWING CONFORMS TO JEDEC MO220 REVISION C.
MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY.
NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY.
PACKAGE OUTLINE
8, 12, 16L THIN QFN, 3x3x0.8mm
21-0136
18
______________________________________________________________________________________
G
2
2
±15kV ESD-Protected USB Transceivers
TSSOP4.40mm.EPS
PACKAGE OUTLINE, TSSOP 4.40mm BODY
21-0066
G
1
1
Revision History
Pages changed at Rev1: 1, 14, 19, slide
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 19
© 2006 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products.
MAX3453E–MAX3456E
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)