19-1805; Rev 1; 4/11 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator The MAX1765 uses a synchronous-rectified pulsewidth-modulation (PWM) boost topology to generate 2.5V to 5.5V outputs from a wide range of input sources, such as one to three alkaline or NiCd/NiMH cells or a single lithium-ion (Li+) cell. Maxim's proprietary architecture significantly improves efficiency at low load currents while automatically transitioning to fixed-frequency PWM operation at medium to high load currents to maintain excellent full-load efficiency. Forced-PWM mode is available for applications that require constant-frequency operation at all load currents, and the MAX1765 may also be synchronized to an external clock to protect sensitive frequency bands in communications equipment. The MAX1765’s low-dropout (LDO) linear regulator and DC-DC converter have separate shutdown control. The linear regulator's 250mΩ pass device maintains excellent dropout voltage at currents up to 500mA. The MAX1765 also features analog soft-start and currentlimit functions to permit optimization of efficiency, external component size, and output voltage ripple. The MAX1765 comes in a 16-pin QSOP package and a thermally enhanced 16-pin TSSOP-EP. ____________________________Features o High-Efficiency Step-Up Converter Up to 93% Efficiency Adjustable Output from +2.5V to +5.5V Up to 800mA Output PWM Synchronous-Rectified Topology 1MHz Operating Frequency (or Sync) o LDO Linear Regulator 500mA LDO Linear Regulator 2.85V Linear Regulator Output or Adjustable (1.25V to 5V) Low 125mV Dropout at 500mA o +0.7V to +5.5V Input Range o 0.1μA Logic-Controlled Shutdown o Adjustable Inductor Current Limit and Soft-Start o Thermal Shutdown o 1.5W, 16-Pin TSSOP-EP Package Available Ordering Information PART TEMP RANGE PIN-PACKAGE MAX1765EEE+ -40°C to +85°C 16 QSOP MAX1765EUE+ -40°C to +85°C 16 TSSOP-EP* *EP = Exposed pad. +Denotes a lead(Pb)-free/RoHS-compliant package. Applications Wireless Handsets PCS Phones Personal Communicators Palmtop Computers Hand-Held Instruments Portable Audio Players Typical Operating Circuit Pin Configuration TOP VIEW (0.7V TO 5.5V) 3.3μH ONL LX ONA POUT INL ONB CLK/SEL TRACK OUT = 3.3V 16 ONL ISET 2 15 TRACK REF 3 14 OUTL OUT GND 4 FB FB 5 MAX1765 REF ILIM FBL 1 OUTL GND FBL PGND OUTL = 2.85V (ADJ 1.25V TO 5V) MAX1765 13 INL 12 POUT OUT 6 11 LX ONA 7 10 PGND CLK/SEL 8 9 ONB QSOP/TSSOP-EP ________________________________________________________________ Maxim Integrated Products 1 For price, delivery, and to place orders, please contact Maxim Distribution at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. MAX1765 General Description The MAX1765 is a high-efficiency, low-noise, step-up DC-DC converter intended for use in battery-powered wireless applications. This device operates at a high 1MHz fixed frequency while maintaining an exceptionally low quiescent supply current (200µA). Its small external components and tiny package make this device an excellent choice for small hand-held applications that require the longest possible battery life. MAX1765 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator ABSOLUTE MAXIMUM RATINGS ONA, ONB, ONL, TRACK, OUT, INL to GND..............-0.3V, +6V PGND to GND.....................................................................±0.3V LX to GND ...............................................-0.3V to (POUT + 0.3V) OUTL to GND ..............................................-0.3V to (INL + 0.3V) CLK/SEL, REF, FB, FBL, ISET, POUT to GND...................................................-0.3V to (OUT + 0.3V) OUTL Short Circuit .....................................................Continuous Continuous Power Dissipation (TA = +70°C) 16-Pin QSOP (derate 8.3mW/°C above +70°C)...........667mW 16-Pin TSSOP-EP (derate 19mW/°C above +70°C) ....1500mW Operating Temperature Range ...........................-40°C to +85°C Junction Temperature ......................................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Soldering Temperature (reflow) .......................................+260°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VOUT = VPOUT = VINL = VONA = VONL = 3.6V, CLK/SEL = FBL = ONB = TRACK = PGND = GND, ISET = REF (bypassed with 0.22µF), LX = open, OUTL = open (bypassed with 4.7µF), TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS V DC-DC CONVERTER Input Voltage Range (Note 1) 0.7 5.5 INL Voltage Range (Note 1) 2.3 5.5 V Minimum Startup Voltage ILOAD < 1mA, TA = +25°C, Figure 2 0.9 1.1 V Temperature Coefficient of Startup Voltage ILOAD < 1mA -2 FB Regulation Voltage VFB FB Input Leakage Current CLK/SEL = OUT, 0 < ILX < 0.55A VFB = 1.35V Output Voltage Adjust Range 2 1.250 1.275 V 0.01 100 nA 2.5 Load Regulation CLK/SEL = OUT, 0 < ILOAD < 800mA OUT Voltage in Track Mode VOUTL > 2.0V, INL = POUT Frequency in Startup Mode 1.215 fLX mV/°C 5.5 -1 VOUTL + 0.4 VOUTL + 0.5 V % VOUTL + 0.6 V 1000 kHz 2.15 2.30 V VOUT = 1.5V 125 Startup to Normal Mode Transition Voltage Rising edge only (Note 2) 2.00 ISET Input Leakage Current VISET = 1.25V 0.01 50 nA Supply Current in Normal Mode (Note 3) CLK/SEL = ONL = GND, no load 100 200 μA Supply Current in Low-Noise PWM Mode (Note 3) CLK/SEL = OUT, no load VFB = 1.5V 130 200 μA FB = GND (LX switching) 2.5 Supply Current in Shutdown ONA = ONL = GND, ONB = OUT 1 _______________________________________________________________________________________ mA 10 μA 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator (VOUT = VPOUT = VINL = VONA = VONL = 3.6V, CLK/SEL = FBL = ONB = TRACK = PGND = GND, ISET = REF (bypassed with 0.22µF), LX = open, OUTL = open (bypassed with 4.7µF), TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC-DC SWITCHES POUT Leakage Current VLX = 0V, VOUT = 5.5V 0.1 10 µA LX Leakage Current VLX = VOUT = V ONB = 5.5V, ONA = GND N-channel 0.1 10 µA 0.17 0.28 P-channel 0.22 0.5 1000 1250 1600 mA 10 50 120 mA 1.230 1.250 1.270 V Switch On-Resistance N-Channel Current Limit (Note 4) ILIM P-Channel Turn-Off Current VISET = 1.25V, CLK/SEL = GND or OUT CLK/SEL = GND Ω REFERENCE Reference Output Voltage VREF IREF = 0A Reference Load Regulation -1µA < IREF < 50µA 5 15 mV Reference Supply Regulation 2.5V < VOUT < 5.5V 0.2 5 mV LINEAR REGULATOR INL Voltage Range (Note 1) INL Startup Voltage VINL Output Voltage in Internal Feedback Mode 2.3 5.5 V VOUT = 2V, rising edge only 2.15 2.30 2.45 V FBL = GND, IOUTL = 10mA 2.80 2.85 2.90 V 150 250 350 mV 1.230 1.250 1.270 V 0.01 50 nA 5 V 1300 mA FBL Dual-Mode Threshold FBL Regulation Voltage FBL Input Leakage Current VFBL FBL = OUTL, IOUTL = 10mA, IREF = 0A VFBL = 1.5V OUTL Adjust Range 1.25 Short-Circuit Current Limit VFBL = 1V Dropout Resistance VFBL = 1V, IOUTL = 500mA 550 0.25 0.5 Ω Load Regulation 1mA < IOUTL < 500mA, FBL = GND 0.5 1 % Line Regulation 2.5V < (VOUT = VINL = VPOUT) < 5.5V, FBL = OUTL 0.5 % INL Supply Current in Shutdown OUTL = ONA = ONL = GND 0.1 10 µA INL No-Load Supply Current IOUTL = 0A, VINL = 5.5V 90 250 AC Power-Supply Rejection f = 10kHz 65 dB Thermal Shutdown Hysteresis approximately 10°C 160 °C -0.5 µA _______________________________________________________________________________________ 3 MAX1765 ELECTRICAL CHARACTERISTICS (continued) MAX1765 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator ELECTRICAL CHARACTERISTICS (continued) (VOUT = VPOUT = VINL = VONA = VONL = 3.6V, CLK/SEL = FBL = ONB = TRACK = PGND = GND, ISET = REF (bypassed with 0.22µF), LX = open, OUTL = open (bypassed with 4.7µF), TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA =+25 °C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS CONTROL INPUTS ONA, ONB, ONL (Note 5) Input Low Level Input High Level 1.1V < VOUT < 1.8V 0.2 1.8V < VOUT < 5.5V 0.4 CLK/SEL 1.2V < VOUT < 5.5V 0.2 × VOUT TRACK 1.2V < VINL < 5.5V 0.2 × VINL ONA, ONB, ONL (Note 5) 1.1V < VOUT < 1.8V VOUT - 0.2 1.8V < VOUT < 5.5V 1.6 CLK/SEL 1.2V < VOUT < 5.5V 0.8 × VOUT TRACK 1.2V < VINL < 5.5V 0.8 × VINL Input Leakage Current (CLK/SEL, ONA, ONB, ONL, TRACK) Internal Oscillator Frequency CLK/SEL = OUT 0.8 External Oscillator Synchronization Range 0.5 Oscillator Maximum Duty Cycle 80 V V 0.01 1 μA 1 1.2 MHz 1.2 MHz 86 90 % Minimum CLK/SEL Pulse 200 ns Maximum CLK/SEL Rise/Fall Time 100 ns 4 _______________________________________________________________________________________ 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator (VOUT = VPOUT = VINL = VONA = VONL = 3.6V, CLK/SEL = FBL = ONB = TRACK = PGND = GND, ISET = REF (bypassed with 0.22µF), LX = open, OUTL = open (bypassed with 4.7µF), TA = -40°C to +85°C, unless otherwise noted.) (Note 6) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC-DC CONVERTER FB Regulation Voltage VFB CLK/SEL = OUT, 0 < ILX < 0.55A 1.210 1.280 V OUT Voltage in Track Mode VOUTL > 2.0V, INL = POUT VOUTL + 0.4 VOUTL + 0.6 V Startup to Normal Mode Transition Voltage Rising edge only (Note 2) 2.00 2.30 V Supply Current in Normal Mode (Note 3) CLK/SEL = ONL = GND, no load 200 µA Supply Current in Low-Noise PWM Mode (Note 3 CLK/SEL = OUT, VFB = 1.5V, no load 200 µA Supply Current in Shutdown ONA = ONL = GND, ONB = OUT 10 µA POUT Leakage Current VLX = 0V, VOUT = 5.5V 10 µA LX Leakage Current VLX = VOUT = V ONB = 5.5V, ONA = GND 10 µA DC-DC SWITCHES Switch On-Resistance N-Channel Current Limit (Note 4) 0.28 P-channel 0.50 VISET = 1.25V, CLK/SEL = GND or OUT Ω 1000 1600 mA 5 120 mA IREF = 0A 1.225 1.275 V FBL = GND, IOUTL = 10mA 2.79 2.90 V 150 350 mV FBL Regulation Voltage FBL = OUTL, IOUTL = 10mA, IREF = 0A 1.225 1.275 V LDO Startup Voltage VOUT = 2V, rising edge only 2.15 2.45 V Dropout Resistance VFBL = 1V, IOUTL = 500mA 0.5 Ω INL Supply Current in Shutdown OUTL = ONA = ONL = GND 10 µA INL No-Load Supply Current IOUTL = 0A, VINL = 5.5V 250 µA P-Channel Turn-Off Current ILIM N-channel CLK/SEL = GND REFERENCE Reference Output Voltage LINEAR REGULATOR Output Voltage in Internal Feedback Mode FBL Input Threshold _______________________________________________________________________________________ 5 MAX1765 ELECTRICAL CHARACTERISTICS MAX1765 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator ELECTRICAL CHARACTERISTICS (continued) (VOUT = VPOUT = VINL = VONA = VONL = 3.6V, CLK/SEL = FBL = ONB = TRACK = PGND = GND, ISET = REF (bypassed with 0.22µF), LX = open, OUTL = open (bypassed with 4.7µF), TA = -40°C to +85°C, unless otherwise noted.) (Note 6) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS CONTROL INPUTS Input Low Level Input High Level ONA, ONB, ONL (Note 5) 1.1V < VOUT < 1.8V 0.2 1.8V < VOUT < 5.5V 0.4 CLK/SEL 1.2V < VOUT < 5.5V 0.2 × VOUT TRACK 1.2V < VINL < 5.5V 0.2 × VINL ONA, ONB, ONL (Note 5) 1.1V < VOUT < 1.8V CLK/SEL 1.2V < VOUT < 5.5V 0.8 × VOUT TRACK 1.2V < VINL < 5.5V 0.8 × VINL 1.8V < VOUT < 5.5V VOUT - 0.2 1.6 Input Leakage Current (CLK/SEL, ONA, ONB, ONL, TRACK) Internal Oscillator Frequency Oscillator Maximum Duty Cycle CLK/SEL = OUT V V 1 μA 0.8 1.2 MHz 79 90 % Note 1: Operating voltage. Since the regulator is bootstrapped to the output, once started it will operate down to 0.7V input. Note 2: The device is in startup mode when VOUT is below this value (see Low-Voltage Startup Oscillator section). Do not apply full load current. Note 3: Supply current into the OUT and POUT pins. This current correlates directly to the actual battery-supply current, but is reduced in value according to the step-up ratio and efficiency. Note 4: Minimum recommended ISET voltage in normal mode is 0.625V. Note 5: ONA, ONB, ONL have hysteresis of approximately 0.15 VOUT. Note 6: Specifications to -40°C are guaranteed by design and not production tested. 6 _______________________________________________________________________________________ 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator 70 NORMAL MODE 60 50 40 VIN = +2.4V 20 40 VIN = +3.6V VIN = +2.4V 0.01 0.1 1 VIN = +2.4V 70 60 VIN = +1.2V PWM MODE 50 40 VIN = +1.2V 30 VIN = +2.4V 20 VIN = +1.2V 10 0 0 0.001 0.01 0.001 0.1 0.001 1 0.01 0.1 1 LOAD CURRENT (A) LOAD CURRENT (A) TRACK MODE EFFICIENCY vs. LOAD CURRENT (VOUTL = +3.3V) TRACK MODE EFFICIENCY vs. LOAD CURRENT (VOUTL = +5V) MAXIMUM OUTPUT CURRENT vs. INPUT VOLTAGE NORMAL MODE VIN = +1.2V VIN = +1.2V NORMAL MODE/ PWM MODE 30 60 VIN = +1.2V 40 30 20 20 10 10 0 0 0.01 0.1 1 VIN = +1.2V VIN = +2.4V VOUT = +3.3V, ISET = REF 800 600 400 200 VOUT = +5V, ISET = 0.5 REF VIN = +3.6V 0 0.001 0.01 0.1 0 1 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 LOAD CURRENT (A) LOAD CURRENT (A) INPUT VOLTAGE (V) LINEAR REGULATOR DROPOUT VOLTAGE vs. LOAD CURRENT STARTUP INPUT VOLTAGE vs. OUTPUT CURRENT NO-LOAD SUPPLY CURRENT vs. INPUT VOLTAGE MAX1765 toc07 0.30 0.25 VOUTL = +2.5V 0.20 VOUTL = +2.85V 0.15 0.10 VOUTL = +5V 0.05 2.5 STARTUP INPUT VOLTAGE (V) 0.001 VIN = +2.4V 50 PWM MODE VOUT = +3.3V, ISET = 0.5 REF TA = +25°C 2.0 TA = -40°C 1.5 18 1.0 TA = +85°C MAX1765 toc09 40 PWM MODE VOUT = +5V, ISET = REF 1000 16 SUPPLY CURRENT (mA) 50 EFFICIENCY (%) 60 14 FPWM MODE 12 10 8 6 4 0.5 2 0 100 200 300 400 500 600 700 800 LOAD CURRENT (mA) NORMAL MODE 0 0 0 MAX1765 toc06 70 VIN = +2.4V 1200 OUTPUT CURRENT (mA) 70 VIN = +3.6V NORMAL MODE 80 MAX1765 toc08 80 90 MAX1765 toc04 VIN = +3.6V VIN = +2.4V MAX1765 toc05 LOAD CURRENT (A) 90 EFFICIENCY (%) PWM MODE 50 NORMAL MODE 80 10 0 DROPOUT VOLTAGE (V) VIN = +1.2V 60 20 10 90 VIN = +2.4V 70 30 VIN = +1.2V 100 MAX1765 toc03 80 VIN = +1.2V PWM MODE 30 90 EFFICIENCY (%) EFFICIENCY (%) 80 VIN = +3.6V NORMAL MODE EFFICIENCY (%) VIN = +2.4V 90 100 MAX1765 toc01 100 TRACK MODE EFFICIENCY vs. LOAD CURRENT (VOUTL = +2.85V) EFFICIENCY vs. LOAD CURRENT (VOUT = +5V) MAX1765 toc02 EFFICIENCY vs. LOAD CURRENT (VOUT = +3.3V) 1 10 100 OUTPUT CURRENT (mA) 1000 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 INPUT VOLTAGE (V) _______________________________________________________________________________________ 7 MAX1765 Typical Operating Characteristics (TA = +25°C, unless otherwise noted.) Typical Operating Characteristics (continued) (TA = +25°C, unless otherwise noted.) LDO PSRR vs. FREQUENCY (100Hz TO 1MHz) LINE TRANSIENT RESPONSE (DC-DC) BOOST FOLLOWED BY LDO OUTPUT NOISE SPECTRUM 12 NOISE (mVRMS) -40 -50 VIN = +2.4V VOUT = +3.3V 14 -20 -30 MAX1765 toc11 -10 MAX1765 toc12 16 MAX1765 toc10 0 LDO PSRR (dB) MAX1765 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator 10 A 8 6 4 2 -60 0 B -70 -80 0.1 1 10 100 0.1 1000 1 10 100μs/div A: VIN, 500mV/div VOUT = +3.3V, I = 0mA B: VOUT, 1mV/div, AC-COUPLED VIN = +1.4V TO +2.4V FREQUENCY (kHz) FREQUENCY (MHz) LINE TRANSIENT RESPONSE (LINEAR) LOAD TRANSIENT RESPONSE MAX1765 toc13 TURN-ON WAVEFORMS NO SOFT-START COMPONENTS MAX1765 toc15a MAX1765 toc14 A A A B B C B I = 0mA, VIN = +3V TO +5V, VOUT = +3.3V A: VIN, 2V/div B: VOUT, 5mV/div, AC-COUPLED A: 0NA, 5V/div B: VOUT, 2V/div C: INPUT CURRENT, 1A/div 50μs/div VIN = +2.4V, VOUT = +3.3V, IOUT = 0 TO 500mA A: IOUT, 500mA/div B: VOUT,100mV/div HEAVY-LOAD SWITCHING WAVEFORMS (IOUT = 650mA, VIN = +2.4V, VOUT = 3.3V) SOFT-START WAVEFORMS (RSS = 500kΩ, CSS = 0.1μF) MAX1765 toc16 MAX1765 toc15b A A B B C C 2.5ms/div A: 0NA, 5V/div B: INPUT CURRENT, 100mA/div C: VOUT, 1V/div 8 500ns/div A: LX, 5V/div B: INDUCTOR CURRENT, 200mA/div C: OUTPUT RIPPLE, 50mV/div, AC-COUPLED _______________________________________________________________________________________ 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator LINEAR-REGULATOR OUTPUT NOISE MAX1765 toc17 ILDO = 200mA VLDO = 2.85V A 250 150 C 50 1.0 0.8 0.6 0.4 0.2 0 500ns/div A: LX NODE, 5V/div B: INDUCTOR CURRENT, 200mA/div, AC-COUPLED C: OUTPUT RIPPLE, 20mV/div, AC-COUPLED VOUT = +3.3 1.2 SWITCH CURRENT LIMIT (A) NOISE (mVRMS) 350 B SWITCH CURRENT LIMIT vs. VISET 1.4 MAX1765 toc18 450 MAX1765 toc19 LIGHT-LOAD SWITCHING WAVEFORMS (VIN = +2.4V, VOUT = +3.3V, IOUT = 10mA) 0.1 1 10 FREQUENCY (MHz) 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 VISET (V) Pin Description PIN NAME 1 FBL Low-Dropout Linear Regulator Dual-Mode Feedback Input. Connect FBL to ground for 2.85V nominal output voltage. Connect FBL to a resistor-divider from OUTL to ground for an adjustable output voltage. FBL regulates to 1.25V. 2 ISET Set N-Channel Current Limit. For maximum current limit, connect ISET to REF. To reduce current limit, use a resistor-divider from REF to GND. If soft-start is desired, a capacitor can be added from ISET to GND. When ONA = LO and ONB = HI or VREF < 80% of nominal value, an on-chip 100kΩ switchable resistor discharges ISET to GND. 3 REF 1.25V Reference Output. Connect a 0.22µF bypass capacitor to GND; 50µA of external load current is allowed. The reference is enabled if ONA = HI, ONB = LO, or ONL = HI. 4 GND Ground. Connect to PGND with short trace. 5 FB 6 OUT Boost Converter IC power is derived from OUT. Connect OUT to POUT through a 4.7Ω resistor and bypass to GND with a 0.68µF capacitor. 7 ONA ON Input. When high, the DC-DC is operational (Table 2). 8 FUNCTION Boost Converter Feedback Input. Connect a resistor-divider between OUT and GND to set the output voltage in the range of 2.5V to 5V. In track mode, FB is disabled after OUTL is in regulation. CLK/SEL CLOCK Input for the DC-DC Converter. Also serves to program operating mode of switch as follows: CLK/SEL = LOW: Normal mode. Operates at a fixed frequency, automatically switching to low-power (SKIP) mode when the load is minimized. CLK/SEL = HI: Forced PWM mode. Operates in low-noise, constant-frequency mode at all loads. CLK/SEL = Clocked: Synchronized forced PWM mode. The internal oscillator is synchronized to an external clock in the 500kHz to 1200kHz frequency range. _______________________________________________________________________________________ 9 MAX1765 Typical Operating Characteristics (continued) (TA = +25°C, unless otherwise noted.) 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator MAX1765 Pin Description (continued) PIN NAME FUNCTION 9 ONB 10 PGND 11 LX 12 POUT 13 INL Linear Regulator Power Input. Source of PFET pass device connected between INL and OUTL. Connect INL to POUT. 14 OUTL Linear Regulator Output. OUTL can source up to 500mA. Bypass OUTL to GND with a 4.7µF capacitor. 15 TRACK Track-Mode Control Input for DC-DC Converter. In track mode, the boost converter output is sensed at OUT and set to 0.5V above OUTL to improve efficiency. Set TRACK to OUT for track mode and to GND for normal operation (Table 2). 16 ONL — EP ON Input. When low, the DC-DC is operational (Table 2). Power Ground Inductor connection to the drain of P-channel synchronous rectifier and N-channel switch. Boost Converter Power Output. POUT is the source of the P-channel synchronous-rectifier MOSFET switch. Connect POUT to INL. Bypass POUT to PGND with a 100µF capacitor. Linear Regulator ON Input. Enables the linear regulator output when TRACK = LOW. ONA and ONB determine the linear regulator’s output state when TRACK = HIGH. Exposed Pad (TSSOP Only). Internally connected to GND and PGND. Connect to a large ground plane. Detailed Description The MAX1765 is a highly efficient, low-noise power supply for portable RF hand-held instruments. This boost power supply combines an LDO linear regulator, a low-noise, high-power, step-up switching regulator, an N-channel power MOSFET, a P-channel synchronous rectifier, shutdown control, and a precision voltage reference in a single 16-pin QSOP or a thermally enhanced TSSOP-EP (Figure 1). The switching DC-DC converter boosts a 1-cell to 3-cell NiMH/NiCd or a single Li+ battery input to an adjustable output voltage between 2.5V and 5.5V. The MAX1765 guarantees startup with voltages as low as 1.1V and will remain operational down to 0.7V (Figure 2). The internal LDO regulator provides linear postregulation for noisesensitive circuitry, or it can be used as a separate voltage output adjustable from 1.25V up to POUT. The MAX1765 is optimized for use in cellular phones and other applications requiring low noise during full-power operation, as well as low quiescent current for maximum battery life during standby and shutdown. The device automatically transitions to a low-quiescent-current pulse-skipping control scheme during light loads that reduces the quiescent power consumption to 360µW. The supply current of the device can be further reduced to 1µA when the device is shut down. Figure 2 shows a typical application of the MAX1765 in normal mode. The switching regulator supports two low-noise modes: fixed-frequency PWM for low noise in all load conditions, 10 and synchronization of the internal oscillator to an external clock driving the CLK input. In TRACK mode, the DC and linear regulator work together to maintain excellent PSRR without excessive efficiency loss. Additional MAX1765 features include synchronous rectification for high efficiency and increased battery life, dual boost shutdown controls for µP or a pushbutton momentary switch, and a separate shutdown control for the linear regulator. Step-Up Converter During DC-DC converter operation, the internal N-channel MOSFET turns on for the first part of each cycle, allowing current to ramp up in the inductor and store energy in a magnetic field. During the second part of each cycle, the MOSFET turns off and inductor current flows through the synchronous rectifier to the output filter capacitor and the load. As the energy stored in the inductor is depleted, the current ramps down and the synchronous rectifier turns off. The CLK/SEL pin determines whether a pulse-skipping or PWM control method is used at light loads (Table 1). Normal Operation Pulling CLK/SEL low selects the MAX1765’s normal operating mode. In this mode, the device operates in PWM when driving medium to heavy loads and automatically switches to SKIP mode if the load requires less power. SKIP mode allows higher efficiency than PWM under light-load conditions. ______________________________________________________________________________________ 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator MAX1765 MAX1765 THERMAL SENSOR SHUTDOWN LOGIC INL FBL ONL MOSFET DRIVER WITH CURRENT LIMITING ERROR AMP OUT P OUTL REF IC PWR POUT 2.15V TRACK EN GND STARTUP OSCILLATOR Q D Q P PWM CONTROLLER ONA ONB ON ONL RDY 1.250V REFERENCE REF OSC VOUT Q EN 1MHz OSCILLATOR CLK/SEL LX EN SKIP/PWM MODE N ICS IREF FB PGND IFB VOUT - 300mV TRACK ISET ISET Figure 1. Functional Diagram Table 1. Selecting the Operating Mode CLK/SEL MODE FEATURES 0 Normal Operation High-efficiency pulse skipping at light loads, PWM at medium and heavy loads 1 Forced PWM Low noise, fixed frequency at all loads External Clock 500kHz to 1.2MHz Synchronized PWM Low noise, fixed frequency at all loads Light-Load Operation in Normal Mode At light loads, the MAX1765 operates by turning on the DC-DC converter’s N-channel field-effect transistor (FET) when VFB < VREF, synchronized with the rising edge of the oscillator. The N-channel FET will remain on, ramping up the inductor current past the minimum inductor current, until the internal error amplifier and current mode circuitry determine that the needs of the system have been met or the device hits the ISET current limit. The N-channel is then turned off and the Pchannel is turned on until current decays to the P-channel turn-off current level. The N-channel will remain off until VFB is again less than VREF, and a rising edge of the oscillator occurs. ______________________________________________________________________________________ 11 MAX1765 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator VIN 0.7V to 3.2V 3.3μH VOUT 3.3V 33μF 100μF REF LX POUT ILIM INL OUT 0.22μF ONA LOGIC INPUTS 4.7Ω 0.68μF MAX1765 ONB TRACK ONL 165k FB 100k VOUTL = 2.85V OUTL 4.7μF FBL GND CLK/SEL PGND rising edge of the oscillator, where the N-channel is again turned on under most conditions. The P-channel zero detect circuitry is deactivated in forced PWM mode. This means an N- or P-channel FET is on all the time for most load conditions. At light loads, the P-channel will remain on so the device can pass current back to the input from the output. The P-channel will only pass current for two cycles before it is disabled. Then, the device remains inactive until VFB < VREF. During forced PWM operation, the MAX1765 switches at a constant frequency (1MHz) and modulates the MOSFET switch pulse width to control the power transferred per cycle in order to regulate the output voltage for most output currents. Switching harmonics generated by fixed-frequency operation are consistent and easily filtered. (See the Boost Followed by LDO Output Noise Spectrum plot in the Typical Operating Characteristics.) Synchronized PWM Operation Figure 2. Typical Application Circuit PWM Operation in Normal Mode The MAX1765 transitions to fixed-frequency PWM operation under medium and heavy loads. The N-channel FET is engaged when VFB < VREF and is kept on to ramp up the current in the inductor until one of the following conditions occurs: the system needs are met, the next falling edge of the internal oscillator is achieved, or the maximum inductor current (ISET) is reached. The N-channel is turned off, activating the Pchannel synchronous rectifier that remains on until the inductor current gets to the P-channel turn-off current level, or VFB < VREF and there is a rising oscillator clock edge. The 1MHz fixed-frequency operation produces an easily filtered fixed-noise spectrum. Forced PWM Operation When CLK/SEL is high, the MAX1765 operates in a lownoise PWM-only mode. The N-channel FET is turned on when VFB < VREF and is kept on to ramp up the inductor current until one of the following conditions occurs: the system needs are met, the next falling edge of the internal oscillator is achieved, or the ISET is reached. The N-channel is then turned off, activating the P-channel synchronous rectifier that remains on until the next 12 The MAX1765 can be synchronized in PWM mode to an external frequency of 500kHz to 1.2MHz by applying an external clock signal to CLK/SEL. This allows interference to be minimized in wireless applications. The synchronous rectifier is active during synchronized PWM operation. Synchronous Rectifier The MAX1765 features an internal 250mΩ, P-channel synchronous rectifier to enhance efficiency. Synchronous rectification provides a 5% efficiency improvement over similar nonsynchronous boost regulators. In PWM mode, the synchronous rectifier is turned on during the second portion of each switching cycle. At light loads (in normal mode), an internal comparator turns on the synchronous rectifier when the voltage at LX exceeds the boost regulator output, and turns it off when the inductor current drops below 50mA. Low-Voltage Startup Oscillator The MAX1765 uses a low-voltage startup oscillator for a 1.1V guaranteed minimum input startup input voltage. A Schottky diode placed across LX and POUT reduces the startup voltage to 0.9V. At startup, the low-voltage oscillator switches the N-channel MOSFET until the output voltage reaches 2.15V. Above this level, the normal boost-converter feedback and control circuitry takes over. Once the device is in regulation, it can operate down to 0.7V input since internal power for the IC is bootstrapped from the OUT pin. Do not apply full load until the output exceeds 2.3V. ______________________________________________________________________________________ 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator MAX1765 Linear Regulator The MAX1765 contains an LDO with a fixed 2.85V (or adjustable) output. The MAX1765 linear regulator features a 250mΩ, P-channel MOSFET pass transistor. This provides several advantages, including longer battery life, over similar designs using a PNP pass transistor. The P-channel MOSFET requires no base-drive current. This reduces quiescent current considerably, since PNP-based regulators tend to waste base-drive current in dropout when the pass transistor saturates. Connect the input of the linear regulator (INL) to POUT. The linear regulator can be used to postfilter the switching regulator or regulate a separate supply voltage. This regulated output is intended to power noise-sensitive analog circuitry, such as low-noise amplifiers and IF stages in cellular phones and other instruments, and can deliver up to 500mA. Use a 4.7µF capacitor with less than a 1Ω equivalent series resistance (ESR) on the output to provide stability. The linear regulator has an internal 1.3A (max) current limit and thermal-overload protection circuitry to protect this output. INPUT 0.7V TO 5.5V LX * OUT ONB SHDN MAX1765 ONA POUT CLK/SEL TRACK ONL INL 33μF REF VOUT = 2.5V - 5.0V AT 500mA OUTL 4.7μF ILIM * 0.22μF GND FB FBL PGND * Configurations There are several useful circuit configurations that can be implemented with the MAX1765. The TRACK input divides the circuit configurations into two types, one where the DC-DC converter tracks to the LDO output, and the other where the boost and the LDO regulate independently. Track Mode Asserting the TRACK input places the MAX1765 into track mode, where the DC-DC switching regulator’s feedback pin (FB) is ignored, and the boost output (POUT) “tracks” to 500mV above the linear regulator output. The primary use of the MAX1765 in TRACK mode is as a simple or very-low-noise step-up/down power supply (see Figures 3 and 4; also see the Maximum Output Current vs. Input Voltage plot in the Typical Operating Characteristics.) This circuit operates as a linear regulator when the input supply (a battery) is greater than VLDO. When the battery discharges below VLDO, the DC-DC converter turns on, boosting POUT to a constant 500mV above the linear regulator output. This configuration also allows for true shutdown (see True Shutdown). Dual-Supply Mode When the TRACK input is low, the MAX1765 operates two independent power supplies, a DC-DC converter, and a linear regulator. One such application of this configuration is shown in Figure 4. In this mode, the device generates two boosted voltages from a single battery * OPTIONAL COMPONENTS Figure 3. Simple Step-Up/Step-Down Converter supply. The DC-DC converter could be used to supply the power amplifier (PA) of a cell phone, while the linear regulator powers the baseband functions within the phone. Asserting TRACK switches the device into track mode when the high-voltage supply for the PA is no longer needed, thus improving efficiency in standbyreceive mode. When the PA again needs 5V, deassert the TRACK input. Shutdown The MAX1765 has a shutdown mode that reduces quiescent current to 1µA. During shutdown, the reference, LDO, DC-DC converter, and all feedback and control circuitry are off. Table 2 shows the MAX1765 shutdown truth table. If ONA, ONB, and ONL are all deasserted, the device is shut down. True Shutdown When a typical boost converter is placed into shutdown, current can flow through the body diode of the synchronous rectifier to the load. The MAX1765 can be configured to allow true shutdown as shown in Figure 5. The shutdown function is active low and is connected to both ONA and ONL. When asserted, both the DC-DC converter and the LDO are shut down simultaneously. ______________________________________________________________________________________ 13 MAX1765 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator Table 2. Operating Mode Truth Table OPERATING MODE Shutdown TRACK ONA ONB ONL LINEAR REGULATOR DC-DC CONVERTER REF X L H L OFF OFF OFF H H X X ON ON ON H X L X L H X H ON ON ON L X L H L H X L OFF ON ON L X L L X L H H ON OFF ON Track Independent Regulation DC-DC Only LDO Only The LDO acts like a switch in this situation and disconnects the input from the load. Connect FBL to a resistor-divider from VREF to GND (R3 and R4 in Figure 5) so that VFBL = 0.5V (above the Dual Mode™ threshold) when OUTL is regulated, to ensure that the linear regulator is saturated. Another method to configure the MAX1765 for true shutdown is shown in Figure 6. This shutdown function is active high and connects to the gate of a low-impedance PFET and ONB. The PFET acts like a switch in this situation and disconnects the input from the load. Reference The MAX1765 has an internal 1.25V, 1% reference. Connect a 0.22µF ceramic bypass capacitor to GND within 0.2in (5mm) of the REF pin. REF can source up to 50µA of external load current. Typically connect ISET to REF to give the MAX1765 full inductor current limit. Design Procedure Setting DC-DC Converter Voltage Set the output voltage between +2.5V and +5.5V by connecting a resistor voltage-divider from OUT to FB to GND (Figure 7). Connect the resistor voltage-divider as close to the IC as possible, within 0.2in (5mm) of FB. Choose R2 of 40kΩ or less, then calculate R1 using: ⎛V ⎞ R1 = R2 ⎜ OUT - 1⎟ ⎝ VFB ⎠ where VFB, the boost-regulator feedback set point, is +1.25V. For output voltages above 4V, connect a Schottky diode between LX and POUT to prevent voltage transition from exceeding the LX voltage rating. Setting the Linear Regulator Voltage The LDO regulation voltage can also be set similarly to the DC-DC converter. Connecting FBL to GND sets the LDO output to 2.85V. To set other output voltages between 1.25V and POUT, connect a resistor-divider from OUTL to FBL to GND (Figure 7). Connect the resistor voltage-divider as close to the IC as possible, within 0.2in (5mm) of FBL. The maximum input bias current for the FBL input is 50nA. Choose R4 of 40kΩ or less, then calculate R3 using: ⎛V ⎞ R3 = R4 ⎜ OUTL - 1⎟ ⎝ VFBL ⎠ where VFBL, the linear regulator feedback set point, is +1.25V. Setting the Switch Current Limit and Soft-Start The ISET pin adjusts the inductor current limit and implements soft-start. With ISET connected to REF, the inductor current limits at 1.25A. With ISET connected to a resistive divider set from REF to GND, the current limit is reduced according to: ⎛ ⎞ RSS2 ILIM = 1.25A ⎜ ⎟ ⎝ RSS1 + RSS2 ⎠ Dual Mode is a trademark of Maxim Integrated Products 14 ______________________________________________________________________________________ 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator MAX1765 INPUT 0.7V TO 5.5V INPUT 3.3μH TRACK = LOW, VOUT = 5.0V TRACK = HIGH, VOUT = 3.35V LX 33μF x 2 OFF MAX1765 LX ON ONB 4.7Ω OUTPUT POUT OUT SHDN OUT MAX1765 0.68μF TRACK 150k TRACK ON OFF OFF ON FB ONL FB ONB 50k ONA POUT 0.22μF REF INL ILIM OUTL GND CLK/SEL FBL PGND VLDO = 2.85V Figure 6. PFET Allows True Boost Shutdown 4.7μF on-chip 100kΩ resistor. At power-up, ISET is 0V and the current limit is zero. As the capacitor voltage rises, the current limit increases and the output voltage rises. The soft-start time constant is: Figure 4. Dual-Output Power Supply tRISE = RSSCSS Placing a capacitor across the lower resistor of the current-limiting resistive divider provides both features simultaneously (Figure 9). INPUT LX ON POUT OFF SHDN Package Selection MAX1765 ONL INL ONA OUTL OUTPUT FBL R4 R3 Figure 5. LDO Enable Allows True Boost Shutdown The MAX1765 is available in two packages, a 16-pin QSOP and a thermally enhanced TSSOP-EP. The QSOP is the less expensive of the two packages, and requires a less complex layout design. This layout allows the designer to route underneath the device. The power dissipation for the QSOP is 0.7W. The TSSOP-EP comes with an exposed metal pad that is connected to the substrate of the IC. This increases the power dissipation up to 1.5W for the TSSOP-EP. To achieve maximum power capability, the exposed pad of the TSSOP-EP should be reflowed to a pad with low thermal resistance. For convenience, this pad can be connected to AGND or PGND. Inductor Selection Implement soft-start by placing a resistor from ISET to REF and a capacitor from ISET to GND (Figure 8). In shutdown, ISET is discharged to GND through an The MAX1765’s high switching frequency allows the use of a small surface-mount inductor. For most applications, a 3.3µH inductor works well. The inductor ______________________________________________________________________________________ 15 MAX1765 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator should have a saturation current rating exceeding the N-channel switch current limit; however, it is acceptable to bias the inductor current into saturation by as much as 20% if a slight reduction in efficiency is acceptable. Lower current-rated inductors may be used if ISET is employed to reduce the peak inductor current (see Setting the Switch Current Limit and SoftStart). For high efficiency, choose an inductor with a high-frequency core material to reduce core losses. To minimize radiated noise, use a toroid or shielded inductor. See Table 3 for suggested components and Table 4 for a list of component suppliers. LINEARREGULATOR OUTPUT OUTL INL STEP-UP OUTPUT POUT MAX1765 R1 R3 OUT FBL R4 FB GND PGND R2 Output Diode To assist startup with input voltages below 1.1V or when VOUT is set for >4V, use a Schottky diode—such as a 1N5817, MBR0520L or equivalent—between LX and POUT (Figure 2). The Schottky diode carries current after the synchronous rectifier turns off. Thus, its current rating only needs to be 500mA. Connect the diode as close to the IC as possible. Do not use ordinary rectifier diodes; their slow switching speeds and long reverse-recovery times render them unacceptable. For input voltages over 1.8V, the Schottky diode may improve light-load efficiency. Input and Output Filter Capacitors Choose input and output filter capacitors that will service the input and output peak currents with acceptable voltage ripple. Choose input capacitors with working voltage ratings over the maximum input voltage and output capacitors with working voltage ratings higher than the output. A 100µF, 100mΩ, low equivalent-series-resistance (ESR) tantalum output capacitor is recommended for most applications. At the output of the linear regulator (OUTL), use a 4.7µF ceramic capacitor for stability at loads up to 500mA. The input filter capacitor reduces peak currents drawn from the input source and also reduces input switching noise. The input voltage source impedance determines the required size of the input capacitor. When operating directly from one or two NiMH cells placed close to the MAX1765, use a single 33µF low-ESR input filter capacitor. The Sanyo POSCAP, Panasonic SP/CB, and Kemet T510 are good low-ESR capacitors. Low-ESR tantalum capacitors offer a good trade-off between price and performance. Do not exceed the ripple current ratings of tantalum capacitors. Avoid aluminum electrolytic capacitors; their high ESR typically results in higher output ripple voltage. 16 Figure 7. Feedback Connections Bypass Capacitors Bypass REF to GND with 0.22µF. Also, bypass OUT to GND with a 0.68µF ceramic capacitor, and connect OUT to POUT with a 4.7Ω resistor. Each of these components should be placed as close to its respective IC pins as possible, within 0.2in (5mm). Layout Considerations High switching frequencies and large peak currents make PC board layout a critical part of design. Poor design will cause excessive EMI and ground bounce, both of which can cause instability or regulation errors by corrupting the voltage and current feedback signals. Power components—such as the inductor, converter IC, filter capacitors, and output diode—should be placed as close together as possible, and their traces should be kept short, direct, and wide. Connect the inductor from the battery to the LX pins as close to the IC as possible. Keep the voltage feedback network very close to the IC, within 0.2in (5mm) of the FB pins. Keep noisy traces, such as those from the LX pin, away from the voltage feedback networks and guarded from them using grounded copper. Refer to the MAX1765 EV kit for a full PC board example. ______________________________________________________________________________________ 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator 0.22μF ( RSS1 ) REF 0.22μF MAX1765 ISET CSS ILIM = 1.25A tSS = RSS CSS 500kΩ < RSS < 1MΩ RSS MAX1765 MAX1765 RSS2 ILIM = 1.25A RSS1 + RSS2 tSS = (RSS1 || RSS2) CSS REF ISET CSS RSS2 Figure 9. Soft-Start, Maximum Current Limit Figure 8. Soft-Start, Reduced Current Limit Table 3. Component Selection Guide PRODUCTION 3.3μH INDUCTORS Applications Information Use in a Typical Wireless Phone Application The MAX1765 is ideal for use in digital cordless and PCS phones. The PA is connected directly to the stepup converter output for maximum voltage swing and power efficiency (Figure 10). The internal linear regulator is used for postregulation to generate low-noise power for DSP, control, and RF circuitry. The following equations may be used to estimate the typical available output current under conditions other than those listed here: I ⎛ ⎞ IOUT,MAX = ⎜ ILIM − RIPPLE ⎟ (I − D) ⎝ 2 ⎠ IRIPPLE = D= [ ] D 1 × × VIN − ILIM × (RNCH + LESR ) fSW L VOUT − VIN + ILIM × (RNCH + LESR ) VOUT + ILIM (RPCH − RNCH ) SCHOTTKY DIODES AVX TPS series Kemet T510 series Sanyo POSCAP series Coilcraft DS3316P Coilcraft LPT3305 Surface Mount CAPACITORS Motorola MBR0520L Nihon EP10QY03 Table 4. Component Suppliers COUNTRY PHONE AVX SUPPLIER USA 843-448-9411 Coilcraft USA 847-639-6400 Kemet USA 810-287-2536 Motorola Sumida USA 408-629-4789 Japan 81-45-474-7030 USA 847-956-0666 Japan 81-3-3607-3302 Note: Please indicate that you are using the MAX1765 when contacting these component suppliers. where ILIM is the peak inductor current limit, fSW is the operating frequency (typically 1.2MHz), L is the inductance of the chosen inductor, LRESR is the resistance of the chosen inductor, RNCH and RPCH are the resistances of the internal N-channel and P-channel, respectively. ______________________________________________________________________________________ 17 MAX1765 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator μC 270k LX CONTROL INPUTS POUT MAX1765 GND MAX1765 INL ONB ON/OFF VDD POUT I/O OUTL ONA I/O μC I/O PA RF 0.1μF 270k Figure 10. Typical Phone Application Figure 11. Momentary Pushbutton On/Off Switch Table 5. Typical Available Output Current NUMBER OF CELLS INPUT VOLTAGE (V) OUTPUT VOLTAGE (V) OUTPUT CURRENT (mA) 1 NiCd/NiMH 1.2 3.3 330 2.4 3.3 730 2.4 5.0 460 3.6 5.0 720 2 NiCd/NiMH 3 NiCd/NiMH or 1 Li+ Table 5 lists the typical available output current when operating with one or more NiCd/NiMH cells or one Li+ cell. Adding a Manual Power Reset A momentary pushbutton switch can be used to turn the MAX1765 on and off (Figure 11). ONA is pulled low and ONB is pulled high to turn the device off. When the momentary switch is pressed, ONB is pulled low and the regulator turns on. The switch must be pressed long enough for the microcontroller (µC) to exit reset and drive ONA high. A small capacitor is added to help debounce the switch. The µC issues a logic high to ONA, which holds the device on, regardless of the switch state. To turn the regulator off, press the switch again, allowing the µC to read the switch status and pull ONA low. When the switch is released, ONB is pulled high. 18 Package Information For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 16 QSOP E16+1 21-0055 90-0167 16 QSOP-EP U16E+3 21-0108 90-0120 ______________________________________________________________________________________ 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator REVISION NUMBER REVISION DATE 0 12/00 Initial release 4/11 Added lead-free designation, updated TOCs 1 and 2, and updated Pin Description section 1 DESCRIPTION PAGES CHANGED — 1, 7, 10 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 _____________________19 © 2011 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products. MAX1765 Revision History