PI3B16232 3.3V, Synchronous 16-Bit to 32-Bit FET Mux/Demux NanoSwitch™ Product Features Product Description • Near-Zero propagation delay. Pericom Semiconductor’s PI3B series of logic circuits are produced using the company's advanced submicron CMOS technology. • 5Ω Switches Connect Between Two Ports • Packages Available : - 56-pin 240mil Wide Thin Plastic TSSOP(A) - 56-pin 300mil Wide Plastic SSOP(V) The PI3B16232 is a 3.3 volt, 16-bit to 32-bit synchronous switch. Two select inputs (S0 and S1) control the data flow. A clock (CLK) and a clock enable (CLKEN) synchronize the device operation. When CLKEN is high, the bus switch remains in the last clocked function. Logic Block Diagram CLKEN CLK S0 28 27 Product Pin Configuration 30 D 1A CE 2B1 V CLK S1 29 2B 2 3A D 4B1 4B 2 CE 5A V CLK 6B1 6B 2 1 of 16 Channels 1A 1 56 SW 55 SW 7A SW 8B1 1B1 A 8B 2 GND B 1B2 Vc c 9A S 10 B1 10 B2 11A Truth Table S1 X L L H H S0 X L H L H CLK X ↑ ↑ ↑ ↑ CLKEN H L L L L 12B1 Function Last State Disconnect A = B1 and A = B2 A = B1 A = B2 12 B 2 13 A 14B 1 14B 2 15A 16B1 16B2 CLK CLKEN 1 1 56 2 55 3 54 4 53 5 52 51 6 50 7 49 8 48 9 47 10 46 11 56-Pin 45 12 A, V 44 13 43 14 42 15 41 16 40 17 39 18 19 20 21 38 37 36 22 23 24 35 34 33 25 26 32 31 27 28 30 29 1B1 1B2 2A 3B1 3B2 4A 5B1 5B2 6A 7B1 7B 2 8A GND Vc c 9B1 9B 2 10A 11B1 11B2 12 A 13B1 13B2 14A 15B1 15B2 16A S0 S1 PS8178C 02/18/04 PI3B16232 3.3V, Synchronous 16-Bit to 32-Bit FET Mux/Demux NanoSwitch Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ...................................................... –65°C to +150°C Ambient Temperature with Power Applied ..................... –40°C to +85°C Supply Voltage Range....................................................... –0.5V to +4.6V DC Input Voltage .............................................................. –0.5V to +4.6V DC Output Current........................................................................ 120 mA Power Dissipation ............................................................................. 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 3.0V to 3.6V) Parameters VIH VIL IIH IIL IOZH VIK RON Description Input HIGH Volatage Input LOW Voltage Input HIGH Current Input LOW Current High Impedance Output Current Clamp Diode Voltage Switch ON Resistance (3) Test Conditions(1) Guaranteed Logic HIHG Level Guaranteed Logic LOW Level VCC = MAX., VIN = VCC VCC = Max., VIN = GND 0 ≤ A, B ≤ VCC VCC = Min., VIN = -18mA VCC = Min., IIN = 0.0V, ION = 48mA or 64mA VCC = Min., VIN = 2.4V, ION = 15mA Min. 2.0 -0.5 - Typ(1) Max. 0.8 ±1 ±1 ±1 -0.7 -1.2 5 8 10 15 Units V µA V Ω Capacitance (TA = 25°C, f = 1 MHz) Parameters CIN CON Description Input Capacitance A/B Capacitance, Switch ON Test Conditions VIN = 0V Typ. 3.0 25.0 Units pF Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. 4. This parameter is determined by device characterization but is not production tested. 2 PS8178C 02/18/04 PI3B16232 3.3V, Synchronous 16-Bit to 32-Bit FET Mux/Demux NanoSwitch Power Supply Characteristics Parameters Description ICC Quiescent Power Supply Current ∆ICC Supply Current per Input @ TTL HIGH ICCD Supply Current per Input per MHz(4) Test Conditions(1) VCC = Max. VIN = GND or VCC VCC = Max. VIN = 3.0V(3) VCC = Max., A & B pins open BE = GND Control Input toggling 50% Duty Cycle Min. Typ. Max. 10 750 0.25 Units µA mA/ MHz Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for applicable device. 2. Typical values are at Vcc = 3.3V, +25°C ambient. 3. Per TTL driven input (control inputs only); A and B pins do not contribute to Icc. 4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant AC or DC currents as they transition. This parameter is not tested, but is guaranteed by design. Switching Characteristics over Operating Range Parameters fCLK tW Description Clock Frequency Pulse Duration tS Setup Time th Hold Time ten tdis tpdI(2,3) tpd2 Enalbe Time Disable Time Propagraion Delay Propagraion Delay Test Condiditons(1) CLK high or low S0, S1 before CLK↑ CLKEN before CLK↑ S0, S1 after CLK↑ CLKEN after CLK↑ CLK to B1, B2 CLK to B1, B2 A to B CLK to A VCC = 3.0 to 3.6V Min. Max. 0 150 3.3 1.9 1.9 1 1.8 1 5 1 6 0.25 1 4.5 Units MHz ns Notes: 1. See Test Circuits and Waveforms. 2. This parameter is guaranteed by design but not tested. 3. The bus switch contributes no propagational delay other than the RC delay of ON resistance of the switch and the load capacitance. 3 PS8178C 02/18/04 PI3B16232 3.3V, Synchronous 16-Bit to 32-Bit FET Mux/Demux NanoSwitch Packaging Mechanical: 56-pin 240mil Wide Thin Plastic TSSOP (A) Package 56 .236 .244 1 .547 .555 6.0 6.2 13.9 14.1 1.20 SEATING PLANE .047 Max. .004 0.09 .008 0.20 .0197 BSC 0.50 .007 .011 0.17 0.27 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS 0.45 .018 0.75 .030 .002 .006 0.05 0.15 .319 BSC 8.1 Packaging Mechanical: 56-pin 300mil Wide Plastic SSOP (V) 56 .291 .299 7.39 7.59 .396 .416 10.06 10.56 Gauge Plane .010 0.25 1 .720 18.29 .730 18.54 .02 .04 0.51 1.01 .015 0.381 x 45˚ .025 0.635 .008 0.20 Nom. .110 2.79 Max .025 BSC 0.635 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS .008 .0135 0.20 0.34 0-8˚ 4 .008 0.20 .016 0.40 PS8178C 02/18/04 PI3B16232 3.3V, Synchronous 16-Bit to 32-Bit FET Mux/Demux NanoSwitch Applications Information Logic Inputs The logic control inputs can be driven up to +3.6V regardless of the supply voltage. For example, given a + 3.3V supply, IN may be driven low to 0V and high to 3.6V. Driving IN Rail-to-Rail® minimizes power consumption. Power-Supply Sequencing and Hot-Plug Information Proper power-supply sequencing is recommended for all CMOS devices. Always apply VCC and GND before applying signals to input/output or control pins. Rail-to-Rail is a registeredtrademark of Nippon Motorola, Ltd. Ordering Information Ordering Code PI3B16232A PI3B16232V Packaging Code A V Desctiption 240-mil TSSOP 300-mil SSOP Notes: 1. Thermal characteristics can be found on the company web site at http://www.pericom.com/packaging/ 2. Number of Transistors = TBD Pericom Semiconductor Corporation • 1-800-435-2336 • http://www.pericom.com 5 PS8178C 02/18/04