Voltage Regulators AN80LxxRMS Series Positive output, low dropout voltage regulator (150 mA type) ■ Overview 0.65±0.15 Unit: mm 1.9±0.1 0.95 0.95 0.16 +0.10 −0.06 0.65±0.15 0.3+0.1 −0.05 1.45±0.1 2.9+0.2 −0.05 ■ Features 0 to 0.1 0.8 • Minimum input and output voltage difference: 0.4 V max. • High accuracy output voltage: (allowance: ±3%) • Built-in reset function terminal (high: active) • Built-in overcurrent limit circuit • Built-in rush current prevention circuit at input voltage rise • Output voltage: 1.8 V to 5.2 V 2.8 +0.2 −0.3 3 4 0.4±0.2 5 0.1 to 0.3 2 1.5 +0.25 −0.05 1 1.1 +0.2 −0.1 The AN80LxxRMS series is a 0.15 A, low dropout, positive voltage regulator with reset function. 20 classifications of output voltages, 1.8 V, 1.9 V, 2.0 V, 2.1 V, 2.2 V, 2.5 V, 2.8 V, 2.9 V, 3.0 V, 3.1 V, 3.2 V, 3.3 V, 3.4 V, 3.5 V, 3.6 V, 4.8 V, 4.9 V, 5.0 V, 5.1 V and 5.2 V are available. In addition, it is adopting the surface mounting type package, so that it is most suited for miniaturization and weight reduction of set equipment. MINI-5D On marking, see page 2 ■ Applications • Cellular phone, PHS, analog cordless phone, other small sized portable equipment ■ Block Diagram IN 1 2 OUT 3 N.C. Current source CONT 5 Start/Stop Error amp. Bandgap reference 4 GND 1 AN80LxxRMS Series Voltage Regulators Series ■ Output Voltage Characteristics at IOUT = 50 mA, Ta = 25°C Type No. Output V AN80L18RMS 1.8 AN80L19RMS 1.9 AN80L20RMS Conditions Min Type Max Unit Marking 1.746 1.8 1.854 V BA 2.9 1.843 1.9 1.957 V BB 2.0 3.0 1.940 2.0 2.060 V BC AN80L21RMS 2.1 3.1 2.037 2.1 2.163 V BD AN80L22RMS 2.2 3.2 2.134 2.2 2.266 V BE AN80L25RMS 2.5 3.5 2.425 2.5 2.575 V BW AN80L28RMS 2.8 3.8 2.716 2.8 2.884 V BF AN80L29RMS 2.9 3.9 2.813 2.9 2.987 V BG AN80L30RMS 3.0 4.0 2.910 3.0 3.090 V BH AN80L31RMS 3.1 4.1 3.007 3.1 3.193 V BJ AN80L32RMS 3.2 4.2 3.104 3.2 3.296 V BK AN80L33RMS 3.3 4.3 3.201 3.3 3.399 V BL AN80L34RMS 3.4 4.4 3.298 3.4 3.502 V BM AN80L35RMS 3.5 4.5 3.395 3.5 3.605 V BN AN80L36RMS 3.6 4.6 3.492 3.6 3.708 V BP AN80L48RMS 4.8 5.8 4.656 4.8 4.944 V BQ AN80L49RMS 4.9 5.9 4.753 4.9 5.047 V BR AN80L50RMS 5.0 6.0 4.850 5.0 5.150 V BS AN80L51RMS 5.1 6.1 4.947 5.1 5.253 V BT AN80L52RMS 5.2 6.2 5.044 5.2 5.356 V BU VIN = 2.8 V BA (Marking example: AN80L18RMS) ■ Pin Descriptions Pin No. Description 1 Input voltage pin 2 Output voltage pin 3 N.C. pin 4 Grounding pin 5 Control pin (High → operation, Low → stop) 2 Voltage Regulators AN80LxxRMS Series ■ Absolute Maximum Ratings Parameter Supply voltage *1 Symbol Rating Unit VCC 14.6 V ICC 300 mA PD 78 mW Topr −30 to +85 °C Tstg −55 to +150 °C Supply current Power dissipation *3 Operating ambient temperature Storage temperature *2 *2 Note) *1: There may be a case of the device destruction when the output (VOUT) and the grounding (GND), or the output (VOUT) and input (VIN) are short-circuited. *2: Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25°C. *3: Topr = Power dissipation for IC alone without heat sink at +85°C. ■ Recommended Operating Conditions Part No. Output voltage Operating supply voltage range (VCC) Unit AN80L18RMS 1.8 2.2 to 14.5 V AN80L19RMS 1.9 2.3 to 14.5 V AN80L20RMS 2.0 2.4 to 14.5 V AN80L21RMS 2.1 2.5 to 14.5 V AN80L22RMS 2.2 2.6 to 14.5 V AN80L25RMS 2.5 2.9 to 14.5 V AN80L28RMS 2.8 3.2 to 14.5 V AN80L29RMS 2.9 3.3 to 14.5 V AN80L30RMS 3.0 3.4 to 14.5 V AN80L31RMS 3.1 3.5 to 14.5 V AN80L32RMS 3.2 3.6 to 14.5 V AN80L33RMS 3.3 3.7 to 14.5 V AN80L34RMS 3.4 3.8 to 14.5 V AN80L35RMS 3.5 3.9 to 14.5 V AN80L36RMS 3.6 4.0 to 14.5 V AN80L48RMS 4.8 5.2 to 14.5 V AN80L49RMS 4.9 5.3 to 14.5 V AN80L50RMS 5.0 5.4 to 14.5 V AN80L51RMS 5.1 5.5 to 14.5 V AN80L52RMS 5.2 5.6 to 14.5 V 3 AN80LxxRMS Series Voltage Regulators Series ■ Electrical Characteristics at Ta = 25°C • AN80L18RMS (1.8 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 2.8 V, IOUT = 50 mA 1.746 1.8 1.854 V Line regulation 1 REGIN1 VIN = 2.8 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 2.8 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 2.8 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 2.8 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 2.8 V, IOUT = 0 mA 350 µA VIN = 2.8 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 1.5 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 62 70 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 1.5 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 2.1 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 2.8 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 2.8 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 2.8 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 38 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 2.8 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 2.8 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.10 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 4 Voltage Regulators AN80LxxRMS Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L19RMS (1.9 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 2.9 V, IOUT = 50 mA 1.843 1.9 1.957 V Line regulation 1 REGIN1 VIN = 2.9 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 2.9 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 2.9 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 2.9 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 2.9 V, IOUT = 0 mA 350 µA VIN = 2.9 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 1.6 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 62 70 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 1.6 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 2.2 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 2.9 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 2.9 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 2.9 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 40 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 2.9 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 2.9 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.10 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 5 AN80LxxRMS Series Voltage Regulators Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L20RMS (2.0 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 3.0 V, IOUT = 50 mA 1.940 2.0 2.060 V Line regulation 1 REGIN1 VIN = 3.0 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 3.0 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 3.0 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 3.0 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 3.0 V, IOUT = 0 mA 350 µA VIN = 3.0 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 1.7 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 62 70 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 1.7 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 2.3 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 3.0 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 3.0 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 3.0 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 42 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 3.0 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 3.0 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.10 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 6 Voltage Regulators AN80LxxRMS Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L21RMS (2.1 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 3.1 V, IOUT = 50 mA 2.037 2.1 2.163 V Line regulation 1 REGIN1 VIN = 3.1 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 3.1 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 3.1 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 3.1 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 3.1 V, IOUT = 0 mA 350 µA VIN = 3.1 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 1.8 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 61 69 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 1.8 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 2.4 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 3.1 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 3.1 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 3.1 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 44 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 3.1 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 3.1 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.10 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 7 AN80LxxRMS Series Voltage Regulators Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L22RMS (2.2 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 3.2 V, IOUT = 50 mA 2.134 2.2 2.266 V Line regulation 1 REGIN1 VIN = 3.2 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 3.2 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 3.2 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 3.2 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 3.2 V, IOUT = 0 mA 350 µA VIN = 3.2 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 1.9 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 61 69 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 1.9 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 2.4 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 3.2 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 3.2 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 3.2 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 46 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 3.2 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 3.2 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.10 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 8 Voltage Regulators AN80LxxRMS Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L25RMS (2.5 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 3.5 V, IOUT = 50 mA 2.425 2.5 2.575 V Line regulation 1 REGIN1 VIN = 3.5 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 3.5 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 3.5 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 3.5 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 3.5 V, IOUT = 0 mA 350 µA VIN = 3.5 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 2.2 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 60 68 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 2.2 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 2.6 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 3.5 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 3.5 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 3.5 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 58 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 3.5 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 3.15 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.10 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 9 AN80LxxRMS Series Voltage Regulators Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L28RMS (2.8 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 3.8 V, IOUT = 50 mA 2.716 2.8 2.884 V Line regulation 1 REGIN1 VIN = 3.8 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 3.8 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 3.8 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 3.8 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 3.8 V, IOUT = 0 mA 350 µA VIN = 3.8 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 2.5 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 60 68 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 2.5 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 2.9 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 3.8 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 3.8 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 3.8 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 58 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 3.8 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 3.8 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.10 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 10 Voltage Regulators AN80LxxRMS Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L29RMS (2.9 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 3.9 V, IOUT = 50 mA 2.813 2.9 2.987 V Line regulation 1 REGIN1 VIN = 3.9 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 3.9 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 3.9 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 3.9 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 3.9 V, IOUT = 0 mA 350 µA VIN = 3.9 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 2.6 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 60 68 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 2.6 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 3.0 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 3.9 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 3.9 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 3.9 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 60 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 3.9 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 3.9 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.12 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 11 AN80LxxRMS Series Voltage Regulators Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L30RMS (3.0 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 4.0 V, IOUT = 50 mA 2.910 3.0 3.090 V Line regulation 1 REGIN1 VIN = 4.0 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 4.0 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 4.0 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 4.0 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 4.0 V, IOUT = 0 mA 350 µA VIN = 4.0 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 2.7 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 60 68 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 2.7 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 3.1 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 4.0 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 4.0 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 4.0 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 62 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 4.0 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 4.0 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.12 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 12 Voltage Regulators AN80LxxRMS Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L31RMS (3.1 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 4.1 V, IOUT = 50 mA 3.007 3.1 3.193 V Line regulation 1 REGIN1 VIN = 4.1 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 4.1 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 4.1 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 4.1 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 4.1 V, IOUT = 0 mA 350 µA VIN = 4.1 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 2.8 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 59 67 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 2.8 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 3.2 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 4.1 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 4.1 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 4.1 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 64 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 4.1 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 4.1 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.12 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 13 AN80LxxRMS Series Voltage Regulators Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L32RMS (3.2 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 4.2 V, IOUT = 50 mA 3.104 3.2 3.296 V Line regulation 1 REGIN1 VIN = 4.2 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 4.2 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 4.2 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 4.2 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 4.2 V, IOUT = 0 mA 350 µA VIN = 4.2 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 2.9 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 59 67 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 2.9 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 3.3 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 4.2 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 4.2 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 4.2 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 66 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 4.2 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 4.2 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.12 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 14 Voltage Regulators AN80LxxRMS Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L33RMS (3.3 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 4.3 V, IOUT = 50 mA 3.201 3.3 3.399 V Line regulation 1 REGIN1 VIN = 4.3 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 4.3 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 4.3 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 4.3 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 4.3 V, IOUT = 0 mA 350 µA VIN = 4.3 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 3.0 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 59 67 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 3.0 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 3.4 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 4.3 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 4.3 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 4.3 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 68 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 4.3 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 4.3 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.12 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 15 AN80LxxRMS Series Voltage Regulators Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L34RMS (3.4 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 4.4 V, IOUT = 50 mA 3.298 3.4 3.502 V Line regulation 1 REGIN1 VIN = 4.4 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 4.4 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 4.4 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 4.4 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 4.4 V, IOUT = 0 mA 350 µA VIN = 4.4 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 3.1 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 58 66 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 3.1 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 3.5 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 4.4 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 4.4 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 4.4 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 70 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 4.4 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 4.4 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.12 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 16 Voltage Regulators AN80LxxRMS Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L35RMS (3.5 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 4.5 V, IOUT = 50 mA 3.395 3.5 3.605 V Line regulation 1 REGIN1 VIN = 4.5 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 4.5 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 4.5 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 4.5 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 4.5 V, IOUT = 0 mA 350 µA VIN = 4.5 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 3.2 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 58 66 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 3.2 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 3.6 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 4.5 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 4.5 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 4.5 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 72 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 4.5 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 4.5 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.12 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 17 AN80LxxRMS Series Voltage Regulators Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L36RMS (3.6 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 4.6 V, IOUT = 50 mA 3.492 3.6 3.708 V Line regulation 1 REGIN1 VIN = 4.6 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 4.6 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 4.6 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 4.6 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 4.6 V, IOUT = 0 mA 350 µA VIN = 4.6 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 3.3 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 58 66 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 3.3 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 3.7 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 4.6 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 4.6 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 4.6 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 74 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 4.6 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 4.6 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.12 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 18 Voltage Regulators AN80LxxRMS Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L48RMS (4.8 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 5.8 V, IOUT = 50 mA 4.656 4.8 4.944 V Line regulation 1 REGIN1 VIN = 5.8 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 5.8 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 5.8 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 5.8 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 5.8 V, IOUT = 0 mA 350 µA VIN = 5.8 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 4.5 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 57 65 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 4.5 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 4.9 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 5.8 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 5.8 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 5.8 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 100 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 5.8 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 5.8 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.20 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 19 AN80LxxRMS Series Voltage Regulators Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L49RMS (4.9 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 5.9 V, IOUT = 50 mA 4.753 4.9 5.047 V Line regulation 1 REGIN1 VIN = 5.9 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 5.9 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 5.9 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 5.9 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 5.9 V, IOUT = 0 mA 350 µA VIN = 5.9 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 4.6 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 57 65 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 4.6 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 5.0 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 5.9 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 5.9 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 5.9 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 102 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 5.9 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 5.9 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.20 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 20 Voltage Regulators AN80LxxRMS Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L50RMS (5.0 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 6.0 V, IOUT = 50 mA 4.850 5.0 5.150 V Line regulation 1 REGIN1 VIN = 6.0 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 6.0 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 6.0 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 6.0 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 6.0 V, IOUT = 0 mA 350 µA VIN = 6.0 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 4.7 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 56 64 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 4.7 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 5.1 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 6.0 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 6.0 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 6.0 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 104 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 6.0 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 6.0 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.20 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 21 AN80LxxRMS Series Voltage Regulators Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L51RMS (5.1 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 6.1 V, IOUT = 50 mA 4.947 5.1 5.253 V Line regulation 1 REGIN1 VIN = 6.1 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 6.1 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 6.1 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 6.1 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 6.1 V, IOUT = 0 mA 350 µA VIN = 6.1 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 4.8 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 56 64 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 4.8 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 5.2 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 6.1 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 6.1 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 6.1 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 106 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 6.1 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 6.1 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.20 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 22 Voltage Regulators AN80LxxRMS Series ■ Electrical Characteristics at Ta = 25°C (continued) • AN80L52RMS (5.2 V type) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 µF, COUT = 10 µF Parameter Symbol Min Typ Max Unit VIN = 6.2 V, IOUT = 50 mA 5.044 5.2 5.356 V Line regulation 1 REGIN1 VIN = 6.2 V → 14.5 V, IOUT = 50 mA 10 50 mV Line regulation 2 REGIN2 VIN = 6.2 V → 9 V, IOUT = 50 mA 5 20 mV REGLOA VIN = 6.2 V, IOUT = 0 mA → 150 mA 50 150 mV IPEAK VIN = 6.2 V, The output current value when VOUT decreases by 5% from its value at IOUT = 50 mA. 180 240 mA IBIAS VIN = 6.2 V, IOUT = 0 mA 350 µA VIN = 6.2 V, IOUT = 0 mA → 150 mA 5 mA Output voltage VOUT Load regulation *1 Peak output current *2 Bias current under no load Conditions Bias current fluctuation to load ∆IBIAS Standby consumption current ISTB VIN = 10 V, VCONT = 0 V 0.1 µA Bias current before starting regulation IRUSH VIN = 4.9 V, IOUT = 0 mA 1.5 5 mA 1 V[rms], f = 120 Hz, IOUT = 10 mA 56 64 dB Ripple rejection ratio RR Minimum input/ output voltage difference 1 VDIF(min)1 VIN = 4.9 V, IOUT = 0 mA 0.1 0.2 V Minimum input/ output voltage difference 2 VDIF(min)2 VIN = 5.3 V, IOUT = 150 mA 0.4 V Control terminal threshold high voltage VCONTH VIN = 6.2 V, IOUT = 50 mA 1.50 V Control terminal threshold low voltage VCONTL VIN = 6.2 V, IOUT = 50 mA 0.30 V 30 µA Control terminal current ICONT VIN = 6.2 V, IOUT = 50 mA VCONT = 1.8 V Note) *1: 1.0 Ω *2: Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time when the output current is 50 mA due to the overcurrent protection. • Design reference data Note) The following values are typical and not guaranteed values. Parameter Min Typ Max Unit 10 Hz ≤ f ≤ 100 kHz, IOUT = 10 mA 108 µV 1 dVOUT Output voltage tempera· ture coefficient VOUT dT VIN = 6.2 V, IOUT = 0 mA −30°C ≤ Ta ≤ +85°C 90 ppm/°C Output rise time * VIN = 6.2 V, IOUT = 50 mA VCONT = 0 V → 1.8 V, CIN = 0.1 µF COUT = 10 µF, VOUT = 90% 0.20 ms Output noise voltage Symbol VNO tON Conditions Note) *: Refer to "■ Application Notes 3. Output rise-time characteristics". 23 AN80LxxRMS Series Voltage Regulators Series ■ Application Notes 1. PD Ta curves of MINI-5D package PD T a 0.500 Power dissipation PD (W) 0.400 Mounted on standard board (glass epoxy: 50 mm × 50 mm × t1.6 mm) Rth(j-a) = 416.6 °C/W 0.300 0.200 0.150 0.100 Independent IC without a heat sink Rth(j-a) = 833.3 °C/W 0.000 0 25 50 75 100 125 150 Ambient temperature Ta (°C) 2. ESR characteristics Oscillation 50 ESR (Ω) 40 30 Stable 20 10 0.1 1 10 100 COUT (µF) • Test circuit IN CONT OUT GND N.C. Load resistance (0 mA to 150 mA) ESR COUT 0 V to 14.5 V Note) 1. Not guaranteed values. 2. The capacitance value used for COUT must be 0.22 µF or more and 100 µF or less. The recommended value is 10 µF. 3. Use a capacitor having ESR (equivalent series resistance of capacitor) of 35 Ω or less (at Ta = −30°C to +85°C). 24 Voltage Regulators AN80LxxRMS Series ■ Application Notes (continued) 3. Output rise-time characteristics tON VOUT: 90% VOUT 1.8 V CONT 0V Time 4. Main characteristics • AN80L18RMS VOUT Ta VOUT Ta 1.89 1.89 Input voltage: 9.0 V 1.87 1.85 1.85 1.83 IOUT = 0 mA 1.81 1.79 IOUT = 150 mA IOUT = 50 mA 1.77 Output voltage VOUT (V) Output voltage VOUT (V) Input voltage: 2.8 V 1.87 1.83 1.81 IOUT = 0 mA IOUT = 150 mA 1.79 1.77 1.75 1.75 1.73 1.73 1.71 −40 −30 −20 −10 0 10 20 30 40 50 60 70 80 90 1.71 −40 −30 −20 −10 0 10 20 30 40 50 60 70 80 90 Temperature Ta (°C) Temperature Ta (°C) • AN80L20RMS VOUT Ta VOUT Ta 2.1 2.1 Input voltage: 9.0 V 2.05 2 IOUT = 0 mA IOUT = 150 mA IOUT = 50 mA 1.95 1.9 −40 −30 −20 −10 0 10 20 30 40 50 60 70 80 90 Temperature Ta (°C) Output voltage VOUT (V) Input voltage: 3.0 V Output voltage VOUT (V) IOUT = 50 mA 2.05 IOUT = 0 mA 2 IOUT = 150 mA IOUT = 50 mA 1.95 1.9 −40 −30 −20 −10 0 10 20 30 40 50 60 70 80 90 Temperature Ta (°C) 25 AN80LxxRMS Series Voltage Regulators Series ■ Application Notes (continued) 4. Main characteristics (continued) • AN80L33RMS VOUT Ta VOUT Ta 3.435 3.435 Input voltage: 9.0 V Input voltage: 4.3 V 3.385 3.335 Output voltage VOUT (V) Output voltage VOUT (V) 3.385 IOUT = 0 mA 3.285 IOUT = 150 mA IOUT = 50 mA 3.235 3.335 3.285 IOUT = 0 mA IOUT = 150 mA IOUT = 50 mA 3.235 3.185 3.185 3.135 −40 −30 −20 −10 0 10 20 30 40 50 60 70 80 90 3.135 −40 −30 −20 −10 0 10 20 30 40 50 60 70 80 90 Temperature Ta (°C) Temperature Ta (°C) • AN80L36RMS VOUT IOUT 3.73 Output voltage VOUT (V) 3.68 VIN = 14.5 V 3.63 VIN = 9.0 V VIN = 4.6 V 3.58 3.53 3.48 0 20 40 60 80 100 120 140 160 180 200 Output current IOUT (mA) ■ Application Circuit Example 1 IN 2 OUT Current source 10 µF 5 Start/Stop 10 µF Error amp. SW Bandgap reference Output off at Low Output on at High 26 3 4 N.C. Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuit examples of the products. It does not constitute the warranting of industrial property, the granting of relative rights, or the granting of any license. (3) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (4) The products and product specifications described in this material are subject to change without notice for reasons of modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, redundant design is recommended, so that such equipment may not violate relevant laws or regulations because of the function of our products. (6) When using products for which dry packing is required, observe the conditions (including shelf life and after-unpacking standby time) agreed upon when specification sheets are individually exchanged. (7) No part of this material may be reprinted or reproduced by any means without written permission from our company. Please read the following notes before using the datasheets A. These materials are intended as a reference to assist customers with the selection of Panasonic semiconductor products best suited to their applications. Due to modification or other reasons, any information contained in this material, such as available product types, technical data, and so on, is subject to change without notice. Customers are advised to contact our semiconductor sales office and obtain the latest information before starting precise technical research and/or purchasing activities. B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but there is always the possibility that further rectifications will be required in the future. Therefore, Panasonic will not assume any liability for any damages arising from any errors etc. that may appear in this material. C. These materials are solely intended for a customer's individual use. Therefore, without the prior written approval of Panasonic, any other use such as reproducing, selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited. 2001 MAR