RT9179 Preliminary Adjustable, 200mA LDO Regulator with Enable Features General Description 200mV Dropout @ 200mA 150µ µA Low Ground Pin Current Excellent Line and Load Regulation <1µ µA Standby Current in Shutdown Mode Guaranteed 200mA Output Current Stable with 1µF input and output ceramic capacitor Adjustable Output Voltage Ranges from 1.175V to 4.5V Over-Temperature/Over-Current Protection The RT9179 is a high performance linear voltage regulator with enable high function and adjustable output with a 0.8V reference voltage. It operates from an input of 3V to 5.5V and provides output current up to 200mA with two external resistors to set the output voltage ranges from 1.175V to 4.5V. The RT9179 has superior regulation over variations in line and load. Also it provides fast respond to step changes in load. Other features include over-current and overtemperature protection. The device has enable pin to reduce power consumption in shutdown mode. Applications The devices is available in the popular 5-lead SOT-25 package. Battery-Powered Equipment Graphic Card Peripheral Cards PCMCIA Card Ordering Information RT9179 Pin Configurations Package Type B : SOT- 25 TOP VIEW Operating Temperature Range C : Commercial Standard Marking Information Prat Number Marking RT9179CB XA DS9179-00 VIN 1 GND 2 EN 3 5 VOUT 4 ADJ SOT-25 July 2003 1 RT9179 Preliminary Typical Appoication Circuit VIN VIN RT9179CB VOUT VOUT R1 ON Enable C1 C3 0.1uF EN GND ADJ R2 1uF C2 1uF OFF Figure 1. Adjustable Operation V OUT = 1.175 x ( 1+ Note: The external feedback resistors are in hundreds of OHM to hundreds of kOHM ranges. Pin Description PIN No. Pin Name Pin Function 1 VIN Supply Input 2 GND Common Ground 3 EN 4 ADJ Chip Enable Control Input. Enable High Note that the device will be in the unstable state if the pin is not connected. The output voltage is set by the internal feedback resistors when this pin grounded. If external feedback resistors are applied, the output voltage will be: VOUT = 1.175 × (1 + 5 VOUT R1 R2 ) Volts Regulator Output Function Block Diagram EN Current-Limit and Thermal Protection Shutdown and Logic Control VIN Thermal SHDN 1.175V VREF +_ MOS Driver VOUT Error Amplifier ADJ GND 2 R1 ) Volts R2 RT9179 Preliminary Absolute Maximum Ratings (Note 1) Supply Input Voltage ------------------------------------------------------------------------------------------------- 6V Power Dissipation, PD @ TA = 25°C SOT-25 ------------------------------------------------------------------------------------------------------------------ 0.25W Lead Temperature (Soldering, 10 sec.) -------------------------------------------------------------------------- 260°C Junction Temperature ------------------------------------------------------------------------------------------------ 150°C Storage Temperature Range ---------------------------------------------------------------------------------------- – 65°C to 150°C ESD Susceptibility (Note 2) HBM --------------------------------------------------------------------------------------------------------------------- 2kV MM ----------------------------------------------------------------------------------------------------------------------- 200V Recommended Operating Conditions (Note 3) Supply Input Voltage ------------------------------------------------------------------------------------------------- 3V to 5.5V Shutdown Input Voltage --------------------------------------------------------------------------------------------- 0V to 5.5V Junction Temperature Range --------------------------------------------------------------------------------------- −40°C to 125°C Electrical Characteristics (VIN = VOUT + 0.7V, IOUT = 10mA, CIN =COUT = 1µF (Ceramic), TA = 25°C unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Units Reference Voltage Tolerance VREF 1.163 1.175 1.187 V Adjust Pin Current IADJ -- -- 10 nA Output Voltage Range VOUT 0.8 -- 4.5 V Quiescent Current (Note 5) IQ Disable, IOUT = 0mA -- 150 -- µA Standby Current (Note 6) ISTBY VIN = 5.5V, Shutdown -- -- 1 µA Current Limit ILIM 0.5 -- -- A Dropout Voltage (Note 4) VDROP IOUT = 10mA -- 10 -- IOUT = 200mA -- 200 - Line Regulation ∆VLINE VOUT + 0.7V < VIN < 5.5V -- 0.001 -- %/V Thermal Shutdown Temperature TSD -- 170 -- °C Thermal Shutdown Hysteresis ∆TSD -- 40 -- °C -- -- 0.4 EN Threshold EN Current Logic-Low Voltage VIL VIN = 3.3V, Shutdown Logic-High Voltage VIH VIN = 3.3V, Enable 2.0 -- -- IEN VIN = 5.5V, Enable -- -- 10 3 mV V nA RT9179 Preliminary Note 1. Stresses beyond those listed under “ Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note 2. Devices are ESD sensitive. Handling precaution recommended. The human body model is a 100pF capacitor discharged through a 1.5KΩ resistor into each pin. Note 3. The device is not guaranteed to function outside its operating conditions. Note 4. Dropout voltage is defined as the input to output differential at which the reference voltage drops 12mV below its nominal value measured at 0.7V differential. Note 5. Quiescent, or ground current, is the difference between input and output currents. It is defined by IQ = IIN − IOUT under no load condition (IOUT = 0mA). The total current drawn from the supply is the sum of the load current plus the ground pin current. Note 6. Standby current is the input current drawn by a regulator when the output voltage is disabled by a shutdown signal (VEN ≤ 0.4V). It is measured with VIN = 5.5V. 4 RT9179 Preliminary Typical Operating Characteristics Output Voltage vs. Temperature 3.29 V IN =5V R1=1.8KΩ V IN =5V 1.19 ADJ Pin Voltage (V) 3.28 Output Voltage (V) ADJ Pin Voltage vs. Temperature 1.2 R2=1KΩ 3.27 3.26 3.25 1.18 1.17 1.16 1.15 1.14 3.24 -50 -25 0 25 50 75 100 -50 125 -25 0 Quiescent Current vs. Temperature V IN =5V 150 140 130 75 100 125 140 130 120 120 -50 -25 0 25 50 75 100 3 125 3.5 Temperature (° C) -30 VOUT=3.3V Dropout Voltage (mV) 240 -40 -50 -60 -70 V IN =4V -90 IL= 10mA 10 100 1000 1K 10000 10K 5 5.5 Tj=125°C 200 Tj=25°C 160 120 Tj=-40°C 80 40 COUT = 1uF (X7R) -100 4.5 Dropout Voltage vs. Io 280 -80 4 Input Voltage (V) PSRR -20 PSRR (dB) 50 Quiescent Current vs. Input Voltage 150 Quiescent Current (uA) Quiescent Current (uA) 160 25 Temperature (° C) Temperature (° C) 0 100000 100K Frequency (Hz) 5 0 40 80 120 Io (mA) 160 200 RT9179 Preliminary Current Limit vs. Temperature 1 V IN 4 =5V 2 Source Current (A) 0.95 Current Limit (A) Output Short-Circuit Protection 0.9 0.85 0.8 1 0.8 0.6 0.4 V IN =5V R1=1.8kΩ R2=1kΩ CIN =1uF CO=1uF 0.2 0.75 0 0.7 -50 -25 0 25 50 75 100 125 Time (1ms/Div) Temperature (°C) Load Regulation 5 4 10 0 ILOAD VOUT Transient(mV) 20 -10 - 20 Transiend(mV) R1=1.8KΩ R2=1KΩ CIN=1uF(Electrolytic) CO=1uF(Electrolytic) VIN=4V to 5V ILOAD:150mA Transiend(A) 6 60 VOUT 40 -20 0.2 0.1 0 -0.1 Time (100us/Div) Enable Threshold Voltage vs. Temperature 0.9 VOUT TURN ON VOUT TURN OFF 0.6 Enable Response EN Transient(v) Enable Threshold Voltage (V) 1 0.7 CIN=1uF(Ceramic) CO=2.2uF(Ceramic) 0 Time (100us/Div) 0.8 V IN =5V R1=1.8KΩ R2=1KΩ 20 6 Vout Transient(v) V IN Transient(V) Line Regulation 7 3 VIN =5V R1 =1.8kΩ R2 =1kΩ CIN =1uF CO =1uF 4 2 0 2 1 0 ILOAD:150mA 0.5 -50 -25 0 25 50 75 100 125 Time (100us/Div) Temperature (° C) 6 RT9179 Preliminary Application Information Like any low-dropout regulator, the RT9179 requires input and output decoupling capacitors. These capacitors must be correctly selected for good performance (see Capacitor Characteristics Section). Please note that linear regulators with a low dropout voltage have high internal loop gains which require care in guarding against oscillation caused by insufficient decoupling capacitance. Region of Stable Cout ESR vs. Load Current Region of Stable Cout ESR(Ω) 100 INPUT CAPACITOR An input capacitance of ≅1µF is required between the device input pin and ground directly (the amount of the capacitance may be increased without limit). The input capacitor MUST be located less than 1 cm from the device to assure input stability (see PCB Layout Section). A lower ESR capacitor allows the use of less capacitance, while higher ESR type (like aluminum electrolytic) require more capacitance. Region of Instable 10 1 Region of Stable 0.1 0.01 Region of Instable 0.001 0 40 80 120 Load Current (mA) 160 200 INPUT-OUTPUT (DROPOUT) VOLTAGE A regulator's minimum input-to-output voltage differential (dropout voltage) determines the lowest usable supply voltage. In battery-powered systems, this determines the useful end-of-life battery voltage. Because the device uses a PMOS, its dropout voltage is a function of drain-to-source on-resistance, RDS(ON), multiplied by the load current: Capacitor types (aluminum, ceramic and tantalum) can be mixed in parallel, but the total equivalent input capacitance/ ESR must be defined as above to stable operation. There are no requirements for the ESR on the input capacitor, but tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will be ≅ 1µF over the entire operating temperature range. VDROPOUT = VIN - VOUT = RDS(ON) × IOUT CURRENT LIMIT OUTPUT CAPACITOR The RT9179 monitors and controls the PMOS’ gate voltage, minimum limiting the output current to 0.5A. The output can be shorted to ground for an indefinite period of time without damaging the part. The RT9179 is designed specifically to work with very small ceramic output capacitors. The recommended minimum capacitance (temperature characteristics X7R or X5R) is 1µF to 4.7µF range with 10mΩ to 50mΩ range ceramic capacitor between LDO output and GND for transient stability, but it may be increased without limit. Higher capacitance values help to improve transient. The output capacitor's ESR is critical because it forms a zero to provide phase lead which is required for loop stability. (When using the Y5V dielectric, the minimum value of the input/output capacitance that can be used for stable over full operating temperature range is 3.3µF.) SHORT-CIRCUIT PROTECTION The device is short circuit protected and in the event of a peak over-current condition, the short-circuit control loop will rapidly drive the output PMOS pass element off. Once the power pass element shuts down, the control loop will rapidly cycle the output on and off until the average power dissipation causes the thermal shutdown circuit to respond to servo the on/off cycling to a lower frequency. Please refer to the section on thermal information for power dissipation calculations. NO LOAD STABILITY The device will remain stable and in regulation with no external load. This is specially important in CMOS RAM keep-alive applications 7 RT9179 Preliminary CAPACITOR CHARACTERISTICS Tantalum: It is important to note that capacitance tolerance and variation with temperature must be taken into consideration when selecting a capacitor so that the minimum required amount of capacitance is provided over the full operating temperature range. In general, a good tantalum capacitor will show very little capacitance variation with temperature, but a ceramic may not be as good (depending on dielectric type). Solid tantalum capacitors are recommended for use on the output because their typical ESR is very close to the ideal value required for loop compensation. They also work well as input capacitors if selected to meet the ESR requirements previously listed. Tantalums also have good temperature stability: a good quality tantalum will typically show a capacitance value that varies less than 10~15% across the full temperature range of 125°C to -40°C. ESR will vary only about 2X going from the high to low temperature limits. Aluminum electrolytics also typically have large temperature variation of capacitance value. Equally important to consider is a capacitor's ESR change with temperature: this is not an issue with ceramics, as their ESR is extremely low. However, it is very important in Tantalum and aluminum electrolytic capacitors. Both show increasing ESR at colder temperatures, but the increase in aluminum electrolytic capacitors is so severe they may not be feasible for some applications. The increasing ESR at lower temperatures can cause oscillations when marginal quality capacitors are used (if the ESR of the capacitor is near the upper limit of the stability range at room temperature). Aluminum: This capacitor type offers the most capacitance for the money. The disadvantages are that they are larger in Ceramic: For values of capacitance in the 10µF to 100µF range, ceramics are usually larger and more costly than tantalums but give superior AC performance for by-passing high frequency noise because of very low ESR (typically less than 10mΩ). However, some dielectric types do not have good capacitance characteristics as a function of voltage and temperature. physical size, not widely available in surface mount, and have poor AC performance (especially at higher frequencies) due to higher ESR and ESL. Compared by size, the ESR of an aluminum electrolytic is higher than either Tantalum or ceramic, and it also varies greatly with temperature. A typical aluminum electrolytic can exhibit an ESR increase of as much as 50X when going from 25°C down to -40°C. Z5U and Y5V dielectric ceramics have capacitance that drops severely with applied voltage. A typical Z5U or Y5V capacitor can lose 60% of its rated capacitance with half of the rated voltage applied to it. The Z5U and Y5V also exhibit a severe temperature effect, losing more than 50% of nominal capacitance at high and low limits of the temperature range. It should also be noted that many aluminum electrolytics only specify impedance at a frequency of 120Hz, which indicates they have poor high frequency performance. Only aluminum electrolytics that have an impedance specified at a higher frequency (between 20kHz and 100kHz) should be used for the device. Derating must be applied to the manufacturer's ESR specification, since it is typically only valid at room temperature. X7R and X5R dielectric ceramic capacitors are strongly recommended if ceramics are used, as they typically maintain a capacitance range within ± 20% of nominal over full operating ratings of temperature and voltage. Of course, they are typically larger and more costly than Z5U/Y5U types for a given voltage and capacitance. Any applications using aluminum electrolytics should be thoroughly tested at the lowest ambient operating temperature where ESR is maximum. 8 RT9179 Preliminary Using a single point ground technique for the regulator and it's capacitors fixed the problem. Since high current THERMAL CONSIDERATIONS The RT9179 can deliver a current of up to 200mA over the full operating junction temperature range. However, the maximum output current must be derated at higher ambient temperature to ensure the junction temperature does not exceed 125°C. With all possible conditions, the junction temperature must be within the range specified under operating conditions. Power dissipation can be calculated based on the output current and the voltage drop across regulator. flows through the traces going into VIN and coming from VOUT, Kelvin connect the capacitor leads to these pins so there is no voltage drop in series with the input and output capacitors. Optimum performance can only be achieved when the device is mounted on a PC board according to the diagram below: ADJ PD = (VIN - VOUT) IOUT + VIN IGND The final operating junction temperature for any set of conditions can be estimated by the following thermal equation: GND VOUT + PD (MAX) = ( TJ (MAX) - TA ) / θJA Where TJ (MAX) is the maximum junction temperature of the die (125°C) and TA is the maximum ambient temperature. The junction to ambient thermal resistance (θJA) for SOT25 package at recommended minimum footprint is 250°C/ W (θ JA is layout dependent). Visit our website in which“ Recommended Footprints for Soldering Surface Mount Packages” for detail. GND EN + + VIN PCB LAYOUT SOT-25 Board Layout Good board layout practices must be used or instability can be induced because of ground loops and voltage drops. The input and output capacitors MUST be directly connected to the input, output, and ground pins of the device using traces which have no other currents flowing through them. The best way to do this is to layout CIN and COUT near the device with short traces to the VIN, VOUT, and ground pins. The regulator ground pin should be connected to the external circuit ground so that the regulator and its capacitors have a “ single point ground” . It should be noted that stability problems have been seen in applications where “ vias“ to an internal ground plane were used at the ground points of the device and the input and output capacitors. This was caused by varying ground potentials at these nodes resulting from current flowing through the ground plane. 9 RT9179 Conceptual Outline Dimension H D L B C b A A1 e Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A 0.889 1.295 0.035 0.051 A1 0.000 0.152 0.000 0.006 B 1.397 1.803 0.055 0.071 b 0.356 0.559 0.014 0.022 C 2.591 2.997 0.102 0.118 D 2.692 3.099 0.106 0.122 e 0.838 1.041 0.033 0.041 H 0.102 0.254 0.004 0.010 L 0.356 0.610 0.014 0.024 SOT- 25 Surface Mount Package RICHTEK TECHNOLOGY CORP. RICHTEK TECHNOLOGY CORP. Headquarter Taipei Office (Marketing) 5F, No. 20, Taiyuen Street, Chupei City 8F-1, No. 137, Lane 235, Paochiao Road, Hsintien City Hsinchu, Taiwan, R.O.C. Taipei County, Taiwan, R.O.C. Tel: (8863)5526789 Fax: (8863)5526611 Tel: (8862)89191466 Fax: (8862)89191465 Email: [email protected] 10