19-1601; Rev 2; 11/05 KIT ATION EVALU LE B A IL A AV 622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET ____________________________Features The MAX3665 low-power transimpedance preamplifier for 622Mbps SDH/SONET applications consumes only 70mW at VCC = 3.3V. Operating from a single +3.3V or +5.0V supply, it converts a small photodiode current to a measurable differential voltage. A DC cancellation circuit provides a true differential output swing over a wide range of input current levels, thus reducing pulse-width distortion. The differential outputs are back-terminated with 50Ω per side. ♦ +3.3V or +5.0V Single-Supply Operation The overall transimpedance gain is nominally 8kΩ. For input signal levels beyond approximately 50µAp-p, the amplifier will limit the output swing to 250mV. The MAX3665’s low 55nA input noise provides a typical sensitivity of -33.2dBm in 1300nm, 622Mbps receivers. The MAX3665 is designed to be used in conjunction with the MAX3676 clock recovery and data retiming IC with limiting amplifier. Together they form a complete 3.3V or 5.0V 622Mbps SDH/SONET receiver. ♦ Differential Output Drives 100Ω Load In die form, the MAX3665 is designed to fit on a header with a PIN diode. It includes a filter connection that provides positive bias for the photodiode through a 1.5kΩ resistor to V CC. The device is available in an 8-pin µMAX® package. ________________________Applications ♦ 55nARMS Input-Referred Noise ♦ 70mW Power Consumption at VCC = 3.3V ♦ 8kΩ Gain ♦ 450µA Peak Input Current ♦ 260ps (max) Deterministic Jitter ♦ 470MHz Bandwidth _______________Ordering Information PART TEMP RANGE PIN-PACKAGE MAX3665EUA MAX3665E/D -40°C to +85°C (see Note) 8 µMAX Dice Note: Dice are designed to operate over a -40°C to +140°C junction temperature (Tj) range, but are tested and guaranteed at TA = +25°C. Pin Configuration appears at end of data sheet. SDH/SONET Receivers PIN Photodiode Preamplifiers and Receivers µMAX is a registered trademark of Maxim Integrated Products, Inc. Regenerators for SDH/SONET __________________________________________________Typical Application Circuit 3.3V 0.01µF RFILT 1.5kΩ VCC MAX3665 3.3V FILT CFILT OUT+ 50Ω 0.1µF IN 50Ω 0.1µF LIMITING AMP CLOCK AND DATA RECOVERY CLK DATA OUTMAX3676 GND ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX3665 ________________General Description MAX3665 622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET ABSOLUTE MAXIMUM RATINGS VCC ........................................................................-0.5V to +6.5V Continuous Current at IN ....................................................±5mA Voltage at OUT+, OUT- ...................(VCC - 1.5V) to (VCC + 0.5V) Voltage at FILT ...........................................-0.5V to (VCC + 0.5V) Continuous Power Dissipation (TA = +85°C) 8-Pin µMAX (derate 4.5mW/°C above +85°C) ...........295mW Operating Junction Temperature (die) ..............-55°C to +150°C Processing Temperature (die) .........................................+400°C Storage Temperature Range .............................-55°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (VCC = +3.3V ±10% or +5.0V ±10%, 100Ω load between OUT+ and OUT-, TA = -40°C to +85°C. Typical values are at VCC = +3.3V, TA = +25°C, unless otherwise noted.) PARAMETER Input Bias Voltage SYMBOL VIN Gain Nonlinearity CONDITIONS MIN IIN = 0 to 300µA IIN = 0 z21 Differential output 7 Output Common-Mode Voltage Maximum Output Voltage Filter Resistor 0.95 V ±5 % 30 mA 21 ICC Small-Signal Transimpedance Output Impedance (per side) MAX 0.8 IIN = 0 to 10µAP-P Supply Current Differential Output Offset TYP ∆VOUT VOUT(MAX) 8 kΩ VCC - 0.15 V ±5 IIN = 300µA 48 ZOUT IIN = 450µAP-P mV 50 52 Ω 260 450 mVP-P 1.5 RFILT UNITS kΩ AC ELECTRICAL CHARACTERISTICS (VCC = +3.3V ±10% or +5.0V ±10%, 100Ω load between OUT+ and OUT-, source capacitance = 0.5pF, TA = -40°C to +85°C. Typical values are at VCC = +3.3V, TA = +25°C, unless otherwise noted.) (Notes 1 and 2) PARAMETER Small-Signal Bandwidth SYMBOL BW-3dB CONDITIONS Relative to gain at 10MHz MIN TYP 404 470 MAX UNITS MHz Low-Frequency Cutoff -3dB with IIN = 5µA 20 40 Deterministic Jitter JD 213 - 1 PRBS with 100 CIDs 100 260 ps RMS Noise Referred to Input in 55 72 nA Power-Supply Rejection Ratio PSRR f < 1MHz, differential referred to output, ∆VCC = 30mVP-P (Note 3) 36 47 Note 1: AC characteristics are guaranteed by design. Note 2: Measured with a 3-pole filter at the output. CIN = 0.5pF, IIN = 0, CFILT = 1000pF. Note 3: PSRR = -20log (∆VOUT / ∆VCC). 2 _______________________________________________________________________________________ kHz dB 622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET SMALL-SIGNAL GAIN vs. FREQUENCY 78 77 75 30 50 CIN = 1pF 73 CIN = 0.5pF CIN IS SOURCE CAPACITANCE PRESENTED TO DIE. IINCLUDES PACKAGE PARASITIC, PIN DIODE, AND PARASITIC INTERCONNECT CAPACITANCE. 0 20 15 71 10 70 5 69 -20 0 20 40 60 80 10k 100k 1M 10M 100M 1G -40 20 40 60 80 100 AMBIENT TEMPERATURE (°C) INPUT-REFERRED NOISE vs. DC INPUT CURRENT SMALL-SIGNAL TRANSIMPEDANCE vs. TEMPERATURE PULSE-WIDTH DISTORTION vs. TEMPERATURE (INPUT = 450µAP-P) 8100 MAX3665 toc04 150 100 VCC = 5.0V 8000 TRANSIMPEDANCE (Ω) 200 50 VCC = 3.3V 45 40 7900 35 7800 30 7700 25 20 VCC = 3.3V 15 7600 10 7500 0 7400 1 10 100 DC INPUT CURRENT (µA) -40 1000 BANDWIDTH vs. TEMPERATURE 525 500 475 450 60 AMBIENT TEMPERATURE (°C) 80 100 -20 0 20 40 60 80 100 AMBIENT TEMPERATURE (°C) AMBIENT TEMPERATURE (°C) DATA-DEPENDENT JITTER vs. INPUT SIGNAL AMPLITUDE OUTPUT COMMON-MODE VOLTAGE (REFERENCED TO VCC) vs. TEMPERATURE 60 40 0 -40 100 VCC = 5.0V 80 400 40 80 VCC = 3.3V 100 20 20 60 120 425 0 40 140 PEAK-TO-PEAK JITTER (ps) 550 20 -0.10 MAX3665-08 VCC = 3.3V or 5.0V 0 160 MAX2665 toc07 575 -20 -0.11 COMMON-MODE VOLTAGE (V) 0 VCC = 5.0V 5 MAX3665 toc09 50 -20 0 FREQUENCY (Hz) SOURCE CAPACITANCE = 0.5pF -40 -20 JUNCTION TEMPERATURE (°C) 250 0.1 VCC = 5.0V VCC = 3.3V 0 100 PWD (ps) -40 25 72 MAX3665 toc05 30 74 MAX3665 toc06 40 PWD (ps) 35 60 10 RMS NOISE CURRNENT (nA) 40 76 20 BANDWIDTH (MHz) 45 70 GAIN (dB) RMS NOISE CURRENT (nA) 80 50 MAX3665 toc02 CIN = 1.5pF 90 79 MAX3665 TOC01 100 PULSE-WIDTH DISTORTION vs. TEMPERATURE (INPUT = 100µAP-P) MAX3665 toc03 INPUT-REFERRED NOISE vs. TEMPERATURE -0.12 -0.13 VCC = 3.3V -0.14 -0.15 VCC = 5.0V -0.16 -0.17 -0.18 -0.19 -0.20 0 50 100 150 200 250 300 350 400 450 PEAK-TO-PEAK AMPLITUDE (µA) -40 -20 0 20 40 60 80 100 AMBIENT TEMPERATURE (°C) _______________________________________________________________________________________ 3 MAX3665 __________________________________________Typical Operating Characteristics (VCC = +3.3V, includes off-chip filter, see Figure 3b, TA = +25°C, unless otherwise noted.) _____________________________Typical Operating Characteristics (continued) (VCC = +3.3V, includes off-chip filter, see Figure 3b, TA = +25°C, unless otherwise noted.) DIFFERENTIAL OUTPUT AMPLITUDE vs. TEMPERATURE (INPUT = 450µAP-P) EYE DIAGRAM (INPUT = 450µAP-P) VCC = 5.0V VCC = 3.3V 250 MAX3665-11 50mV/div 300 15mV/div 350 MAX3665-12 EYE DIAGRAM (INPUT = 10µAP-P) MAX3665 toc10 400 PEAK-TO-PEAK AMPLITUDE (mV) MAX3665 622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET 200 INPUT: 213 - 1 PRBS CONTAINS 100 ZEROS 150 -40 -20 0 20 40 60 80 100 INPUT: 213 - 1 PRBS CONTAINS 100 ZEROS 200ps/div 200ps/div AMBIENT TEMPERATURE (°C) _____________________Pin Description PIN NAME 1 VCC +3.3V or +5.0V Supply Voltage 2 IN Signal Input (From Photodiode) 3 N.C. FUNCTION FILT On-Chip Resistor for Filtering Photodiode Supply Voltage 5, 8 GND Ground 6 OUT+ Noninverting Voltage Output. Current flowing into IN causes VOUT+ to increase. OUT- Inverting Voltage Output. Current flowing into IN causes VOUT- to decrease. 1.5kΩ D2 VCC RF R1 50Ω VCC OUT+ Q2 VCC IN Q1 VCC PARAPHASE AMP R2 50Ω Q3 R6 The MAX3665 is a transimpedance amplifier designed for 622Mbps SDH/SONET applications. It comprises a transimpedance amplifier, a paraphase amplifier with CML differential outputs, and a DC cancellation loop. Figure 1 shows a functional diagram of the MAX3665. The signal current at IN flows into the summing node of a high-gain amplifier. Shunt feedback through RF converts this current to a voltage. Diodes D1 and D2 clamp the output voltage for large input currents. Q5 REFERENCE AMP R4 Q4 R3 DC CANCELLATION AMP MAX3665 GND Figure 1. Functional Diagram 4 R5 OUT- R7 ________________Detailed Description Transimpedance Amplifier FILT D1 No Connection. Not internally connected. 4 7 VCC _______________________________________________________________________________________ 622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET DC Cancellation Loop The DC cancellation loop removes the DC component of the input signal by using low-frequency feedback. This feature centers the signal within the MAX3665’s dynamic range, reducing pulse-width distortion on large input signals. The output of the transimpedance amplifier is sensed through resistors R3 and R4 and then filtered, amplified, and fed back to the base of transistor Q4. The transistor draws the DC component of the input signal away from the transimpedance amplifier’s summing node. Connect a 400pF or larger capacitor (CFILT) between FILT and case ground for TO header, die-mounted operation. Increasing CFILT improves PSRR. The DC cancellation loop can sink up to 300µA of current at the input. The MAX3665 minimizes pulse-width distortion for data sequences that exhibit a 50% mark density. A mark density other than 50% causes the device to generate pulse-width distortion. 375MHz and 622MHz. Lower bandwidth causes pattern-dependent jitter and a lower signal-to-noise ratio, while higher bandwidth increases thermal noise. The MAX3665 typical bandwidth is 470MHz, making it ideal for 622Mbps applications. The preamplifier’s transimpedance must be high enough to ensure that expected input signals generate output levels exceeding the sensitivity of the limiting amplifier (quantizer) in the following stage. The MAX3676 clock recovery and limiting amplifier IC has an input sensitivity of 3.6mV P-P , which means that 3.6mVP-P is the minimum signal amplitude required to produce a fully limited output. Therefore, when used with the MAX3665, which has an 8kΩ transimpedance, the minimum detectable photodetector current is 450nAP-P. It is common to relate peak-to-peak input signals to average optical power. The relationship between optical input power and output current for a photodetector is called the responsivity (ρ), with units amperes per watt (A/W). The photodetector peak-to-peak current is related to the peak-to-peak optical power as follows: IP-P = (PP-P)(ρ) Based on the assumption that SDH/SONET signals maintain a 50% mark density, the following equations relate peak-to-peak optical power to average optical power and extinction ratio (Figure 2): Average Optical Power = PAVG = (P0 + P1) / 2 Extinction Ratio = re = P1 / P0 Peak-to-Peak Signal Amplitude = PP-P = P1 - P0 DC cancellation current is drawn from the input and adds noise. For low-level signals with little or no DC component, this is not a problem. Preamplifier noise will increase for signals with a significant DC component. ___________Applications Information The MAX3665 is a low-noise, wide-bandwidth transimpedance amplifier that is ideal for 622Mbps SDH/ SONET receivers. Its features allow easy design into a fiber optic module, in three simple steps. Step 1: Selecting a Preamplifier for a 622Mbps Receiver Fiber optic systems place requirements on the bandwidth, gain, and noise of the transimpedance preamplifier. The MAX3665 optimizes these characteristics for SDH/SONET receiver applications that operate at 622Mbps. In general, the bandwidth of a fiber optic preamplifier should be 0.6 to 1 times the data rate. Therefore, in a 622Mbps system, the bandwidth should be between POWER P1 PAVG P0 TIME Figure 2. Optical Power Definitions _______________________________________________________________________________________ 5 MAX3665 Paraphase Amplifier The paraphase amplifier converts single-ended inputs to differential outputs, and introduces a voltage gain. This signal drives a differential pair of transistors, Q2 and Q3, which form the output stage. Resistors R1 and R2 provide back-termination at the output, absorbing reflections between the MAX3665 and its load. The differential outputs are designed to drive a 100Ω load between OUT+ and OUT-. They can also drive higher output impedances, resulting in increased gain and output voltage swing. MAX3665 622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET Therefore, PAVG = PP-P (1 / 2)[(re + 1) / (re - 1)] Sensitivity is a key specification of the receiver module. The ITU/Bellcore specifications for SDH/SONET receivers require a link sensitivity of -27dBm with a bit error rate (BER) of 10-10. There is an additional 1dB power penalty to accommodate various system losses; therefore, the sensitivity of a 622Mbps receiver must be better than -28dBm. Although several parameters affect sensitivity (such as the quantizer sensitivity and preamplifier gain, as previously discussed), most fiber optic receivers are designed so that noise is the dominant factor. Noise from the highgain transimpedance amplifier, in particular, determines the sensitivity. The noise generated by the MAX3665 can be modeled with a Gaussian distribution. In this case, a BER of 10 -10 corresponds to a peak-to-peak signal amplitude to RMS noise ratio (SNR) of 12.7. The MAX3665’s typical input-referred noise, in, (bandwidthlimited to 470MHz) is 55nARMS. Therefore, the minimum input for a BER of 10-10 is (12.7 · 55nA) = 699nAP-P. Rearranging the previous equations in these terms results in the following relationship: Optical Sensitivity (dBm) = 10log[(in / ρ)(SNR)(1/2)(re + 1) / (re - 1)(1000)] At room temperature, with re = 10, SNR = 12.7, in = 55nA, and ρ = 0.9A/W, the MAX3665 sensitivity is -33.2dBm. For worst-case conditions, noise increases to 72nA and sensitivity decreases to -32.1dBm. The MAX3665 provides 5.1dB margin over the SDH/SONET specifications, even at +85°C. The MAX3665’s overload current (IMAX) is greater than 450µAP-P. The pulse-width distortion and input current are closely related. If the clock recovery circuit can accept more pulse-width distortion, a higher input current might be acceptable. For worst-case responsivity and extinction ratio, ρ = 1A/W and re = ∞, the input overload is: Overload (dBm) = -10log (IMAX)(1 / 2)(1000) For IMAX = 450µA, the MAX3665 overload is -6.5dBm. Step 2: Designing Filters The MAX3665’s noise performance is a strong function of the circuit’s bandwidth, which changes over temperature and varies from lot to lot. The receiver sensitivity can be improved by adding filters to limit this bandwidth. Filter designs can range from a one-pole filter using a single capacitor, to more complex filters using inductors. Figure 3 illustrates two examples: the simple filter provides moderate roll-off with minimal compo- 6 nents, while the complex filter provides a sharper rolloff. Parasitics on the PC board will affect the filter characteristics. Refer to the MAX3665 EV kit data sheet for a layout example of the filter shown in Figure 3b. Supply voltage noise at the cathode of the photodiode produces a current I = CPHOTO (∆V/∆t), which reduces the receiver sensitivity. C PHOTO is the photodiode capacitance. The FILT resistor of the MAX3665, combined with an external capacitor (see Typical Operating Circuit) can be used to reduce this noise. The external capacitor (C FILT ) is placed in parallel with the photodiode. Current generated by supply noise is divided between CFILT and CPHOTO. The input noise current due to supply noise is (assuming the filter capacitor is much larger than the photodiode capacitance): INOISE = (VNOISE )(CPHOTO ) (RFILT )(CFILT ) a) SIMPLE, 1-POLE, 530MHz FILTER MAX3665 50Ω C1 5pF 1.2pF RL 100Ω 50Ω b) 3-POLE, 515MHz FILTER MAX3665 22nH 50Ω 1.2pF 4pF 5pF RL 100Ω 50Ω 22nH REFER TO THE MAX3665 EV KIT DATA SHEET FOR THE FILTER LAYOUT EXAMPLE. Figure 3. Filter Design Examples _______________________________________________________________________________________ 622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET CFILT = (VNOISE )(CPHOTO ) (RFILT )(INOISE ) For example, with maximum noise voltage = 100mVP-P, CPHOTO = 0.5pF, RFILT = 1.5kΩ, and INOISE selected to be 6nA (1/10 of MAX3665 input-referred noise): ( )( ) ( )( ) CFILT = 0.1 0.5 ⋅ 10−12 / 1500 6 ⋅ 10−4 = 5.6nF Figure 4 shows the suggested layout for a TO-46 header Step 3: Designing a Low-Capacitance Input Noise performance and bandwidth are adversely affected by stray capacitance on the input node. Select a low-capacitance photodiode and use good high-frequency design and layout techniques to minimize capacitance on this pin. The MAX3665 is optimized for 0.5pF of capacitance on the input—approximately the capacitance of a photodetector diode sharing a common header with the MAX3665 in die form. Photodiode capacitance changes significantly with bias voltage. With a +3.3V supply voltage, the reverse voltage on the PIN diode is only 2.5V. If a higher voltage supply is available, apply it to the diode to significantly reduce capacitance. Take great care to reduce input capacitance. With the µMAX version of the MAX3665, the package capacitance is about 0.3pF, and the PC board between the MAX3665 input and the photodiode can add parasitic capacitance. Keep the input line short, and remove power and ground planes beneath it. Packaging the MAX3665 into a header with the photodiode provides the best possible performance. It reduces parasitic capacitance to a minimum, resulting in the lowest noise and the best bandwidth. Wire Bonding For high current density and reliable operation, the MAX3665 uses gold metallization. Make connections to the die with gold wire only, and use ball-bonding techniques (wedge-bonding is not recommended). Die-pad size is 4 mils square. Die thickness is 16 mils. VCC and Ground Use good high-frequency design and layout techniques. The use of a multilayer circuit board with separate ground and VCC planes is recommended. Take care to bypass VCC and to connect the GND pin to the ground plane with the shortest possible traces. _______________________________________________________________________________________ 7 MAX3665 If the amount of tolerable noise is known, then the filter capacitor can be easily selected: MAX3665 622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET TOP VIEW OF TO-46 HEADER VCC GND PHOTODIODE CFILT CVCC OUT+ IN FILT OUT- MAX3665 PHOTODIODE IS MOUNTED ON CFILT. CASE IS GROUND. Figure 4. Suggested Layout for TO-46 Header 8 _______________________________________________________________________________________ 622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET FILT IN TOP VIEW VCC 1 8 GND IN 2 7 OUT- 6 OUT+ 5 GND N.C. 3 MAX3665 FILT 4 MAX3665 ___________________Pin Configuration ___________________Chip Topography VCC µMAX GND GND 0.05" (1.27mm) IN OUT+ OUT0.03" (0.76mm) TRANSISTOR COUNT: 443 SUBSTRATE CONNECTED TO GND _______________________________________________________________________________________ 9 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) 4X S 8 E Ø0.50±0.1 8 INCHES DIM A A1 A2 b H c D e E H 0.6±0.1 1 L 1 α 0.6±0.1 S BOTTOM VIEW D MIN 0.002 0.030 MAX 0.043 0.006 0.037 0.014 0.010 0.007 0.005 0.120 0.116 0.0256 BSC 0.120 0.116 0.198 0.188 0.026 0.016 6° 0° 0.0207 BSC 8LUMAXD.EPS MAX3665 622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET MILLIMETERS MAX MIN 0.05 0.75 1.10 0.15 0.95 0.25 0.36 0.13 0.18 2.95 3.05 0.65 BSC 2.95 3.05 4.78 5.03 0.41 0.66 0° 6° 0.5250 BSC TOP VIEW A1 A2 e A α c b L SIDE VIEW FRONT VIEW PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, 8L uMAX/uSOP APPROVAL DOCUMENT CONTROL NO. 21-0036 REV. J 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 10 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc.