MAXIM MAX9770ETI

19-3134; Rev 0; 5/04
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
The MAX9770 combines a mono, filterless, Class D
speaker amplifier and stereo DirectDrive headphone
amplifiers in a single device. The MAX9770 operates
from a single 2.5V to 5.5V supply and includes features
that reduce external component count, system cost,
board space, and offer improved audio reproduction.
The speaker amplifier makes use of Maxim’s patented
Class D architecture, providing Class AB performance
with Class D efficiency, conserving board space, and
extending battery life. The speaker amplifier delivers
1.2W into an 8Ω load while offering efficiencies above
85%. A spread-spectrum scheme reduces radiated
emissions caused by the modulation frequency.
Furthermore, the MAX9770 oscillator can be synchronized to an external clock through the SYNC input,
avoiding possible problem frequencies inside a system.
The speaker amplifier features a low 0.025% THD+N,
high 70dB PSRR, and SNR in excess of 90dB.
The headphone amplifiers feature Maxim’s patented
DirectDrive architecture that produces a ground-referenced output from a single supply, eliminating the need
for large DC-blocking capacitors. The headphone amplifiers deliver up to 80mW into a 16Ω load, feature low
0.015% THD+N, high 80dB PSRR, and ±8kV ESD-protected outputs. A headphone sense input detects the
presence of a headphone, and automatically configures
the amplifiers for either speaker or headphone mode.
The MAX9770 includes internally set, logic-selectable
gain, and a comprehensive input multiplexer/mixer, allowing multiple audio sources to be selected and for true
mono reproduction of a stereo source in speaker mode.
Industry-leading click-and-pop suppression eliminates
audible transients during power and shutdown cycles. A
low-power shutdown mode decreases supply current
consumption to 0.1µA, further extending battery life.
The MAX9770 is offered in space-saving, thermally efficient 28-pin TQFN (5mm x 5mm x 0.8mm) and 28-pin
TSSOP packages. The MAX9770 features thermal-overload and output short-circuit protection, and is specified
over the extended -40°C to +85°C temperature range.
Applications
Cellular Phones
PDAs
Compact Notebooks
Features
♦ 1.2W Filterless Class D Amplifier Passes FCC
Class B Radiated Emissions Standards with
100mm of Cable
♦ Unique Spread-Spectrum Mode Offers 5dB
Emissions Improvement Over Conventional
Methods
♦ 80mW DirectDrive Headphone Amplifier
Eliminates Bulky DC-Blocking Capacitors
♦ High 80dB PSRR at 217Hz
♦ 85% Efficiency
♦ Low 0.015% THD+N
♦ Industry-Leading Click-and-Pop Suppression
♦ Integrated 3-Way Input Mixer/Multiplexer
♦ Logic-Selectable Gain
♦ Short-Circuit and Thermal Protection
♦ ±8kV ESD-Protected Headphone Outputs
♦ Low-Power Shutdown Mode
♦ Available in Space-Saving, Thermally Efficient
Packages
28-Pin TQFN (5mm x 5mm x 0.8mm)
28-Pin TSSOP
Ordering Information
TEMP RANGE
PIN-PACKAGE
MAX9770ETI†
PART
-40oC to +85oC
28 TQFN-EP*
MAX9770EUI
-40oC to +85oC
28 TSSOP
†Lead-free package.
*EP = Exposed paddle.
Simplified Block Diagram
VDD
DirectDrive
STEREO
HEADPHONE
L1IN
L2IN
MONO
R1IN
R2IN
GAIN SEL
INPUT SEL
MUTE
SHDN
HPS
CLASS
D
SPKR
(MONO)
MAX9770
Pin Configuration appears at end of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX9770
General Description
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
ABSOLUTE MAXIMUM RATINGS
GND to PGND to CPGND......................................-0.3V to +0.3V
VDD to PVDD to CPVDD..........................................-0.3V to +0.3V
VDD to GND..............................................................................6V
PVDD to PGND .........................................................................6V
CPVDD to CPGND ....................................................................6V
CPVSS to CPGND....................................................................-6V
SVSS to GND ...........................................................................-6V
C1N..........................................(PVSS - 0.3V) to (CPGND + 0.3V)
HPOUT_ to GND ....................................................................±3V
All other pins to GND..................................-0.3V to (VDD + 0.3V)
Continuous Current Into/Out of:
PVDD, PGND, OUT_ ......................................................600mA
PVSS ..............................................................................260mA
Duration of HPOUT_ Short Circuit to VDD, PVDD,
GND, PGND ...........................................................Continuous
Duration of Short Circuit between
HPOUTL and HPOUTR ..........................................Continuous
Duration of OUT_ Short Circuit to VDD, PVDD, GND, PGND ..10s
Duration of Short Circuit Between OUT+ and OUT-...............10s
Continuous Power Dissipation (TA = +70°C)
28-Pin TQFN (derate 20.8mW/°C above +70°C) .......1667mW
28-Pin TSSOP (derate 12.8mW°C above +70°C) ......1026mW
Junction Temperature ......................................................+150°C
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = PVDD = CPVDD = 3.3V, GND = PGND = CPGND = 0V, SHDN = 3.3V, C1 = C2 = 1µF, CBIAS = 0.047µF, SYNC = GND, RL = ∞,
speaker load connected between OUT+ and OUT-, headphone load connected between HPOUT_ and GND, TA = TMIN to TMAX,
unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
5.5
V
GENERAL
Supply Voltage Range
VDD
Quiescent Supply Current
IDD
Shutdown Supply Current
ISHDN
Shutdown to Full Operation
tON
Input Impedance
RIN
Bias Voltage
Inferred from PSRR test
No load
2.5
Headphone mode
5.5
10
Speaker mode
5.2
7.5
0.1
10
SHDN = HPS = GND
50
(Note 3)
MONO
7
10
INL_, INR_
14
20
1.1
1.25
VBIAS
From any unselected input to any output,
f = 10kHz
Feedthrough
mA
µA
ms
kΩ
1.4
70
V
dB
SPEAKER AMPLIFIER (GAIN1 = GAIN2 = VDD, HPS = GND)
Output Offset Voltage
±15
VOS
VDD = 2.5V to 5.5V
Power-Supply Rejection Ratio
PSRR
(Note 4)
50
VRIPPLE = 200mVP-P, f = 217Hz
70
VRIPPLE = 200mVP-P, f = 1kHz
68
VRIPPLE = 200mVP-P, f = 20kHz
Output Power
Total Harmonic Distortion Plus
Noise
2
POUT
THD+N
f = 1kHz,
THD+N = 1%,
GAIN1 = 1,
GAIN2 = 0
VDD = 3.3V
VDD = 5V
±70
mV
70
dB
50
RL = 8Ω
550
RL = 4Ω
900
RL = 8Ω
1200
RL = 8Ω, POUT = 300mW, f = 1kHz
0.025
RL = 4Ω, POUT = 300mW, f = 1kHz
0.03
_______________________________________________________________________________________
mW
%
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
(VDD = PVDD = CPVDD = 3.3V, GND = PGND = CPGND = 0V, SHDN = 3.3V, C1 = C2 = 1µF, CBIAS = 0.047µF, SYNC = GND, RL = ∞,
speaker load connected between OUT+ and OUT-, headphone load connected between HPOUT_ and GND, TA = TMIN to TMAX,
unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1, 2)
PARAMETER
Signal-to-Noise Ratio
Output Switching Frequency
SYMBOL
SNR
FS
CONDITIONS
MIN
RL = 8Ω, VOUT = 2VRMS, A-weighted
Gain
980
1100
1220
SYNC = FLOAT
1280
1450
1620
2000
PO = 1000mW, f = 1kHz
85
GAIN1 = 0, GAIN2 = 0
6
GAIN1 = 0, GAIN2 = 1
3
GAIN1 = 1, GAIN2 = 0
9
GAIN1 = 1, GAIN2 = 1
0
HPS = VDD, headphone amplifier active,
f = 1kHz
kHz
%
dB
±5
Gain Accuracy
Speaker Path Off-Isolation
kHz
1220
±120kHz
800
AV
UNITS
dB
SYNC = GND
SYNC Frequency Lock Range
η
MAX
85.9
SYNC = VDD
Efficiency
TYP
102
%
dB
HEADPHONE AMPLIFIER (GAIN1 = 1, GAIN2 = 0, HPS = VDD )
Output Offset Voltage
±5
VOS
VDD = 2.5V to 5.5V
Power-Supply Rejection Ratio
PSRR
(Note 3)
65
85
VRIPPLE = 200mVP-P, f = 1kHz
82
Output Power
POUT
f = 1kHz,
THD+N = 1%
VDD = 3.3V
VDD = 5V
RL = 32Ω
mV
76
VRIPPLE = 200mVP-P, f = 217kHz
VRIPPLE = 200mVP-P, f = 20kHz
±10
dB
56
40
55
RL = 16Ω
40
RL = 32Ω
60
RL = 16Ω
80
mW
RL = 32Ω, POUT = 50mW, f = 1kHz
0.015
RL = 16Ω, POUT = 35mW, f = 1kHz
0.03
RL = 32Ω, VOUT = 300mVRMS,
BW = 22Hz to 22kHz
101
dB
Crosstalk
Between channels, f = 1kHz,
VIN = 200mVP-P
80
dB
Headphone Off-Isolation
HPS = GND, speaker amplifier active,
f = 1kHz
96
dB
Total Harmonic Distortion Plus
Noise
Signal-to-Noise Ratio
THD+N
SNR
%
_______________________________________________________________________________________
3
MAX9770
ELECTRICAL CHARACTERISTICS (continued)
ELECTRICAL CHARACTERISTICS (continued)
(VDD = PVDD = CPVDD = 3.3V, GND = PGND = CPGND = 0V, SHDN = 3.3V, C1 = C2 = 1µF, CBIAS = 0.047µF, SYNC = GND, RL = ∞,
speaker load connected between OUT+ and OUT-, headphone load connected between HPOUT_ and GND, TA = TMIN to TMAX,
unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1, 2)
PARAMETER
SYMBOL
Capacitive-Load Drive
CONDITIONS
MIN
TYP
CL
Gain
MAX
1000
AV
GAIN1 = 0, GAIN2 = 0
7
GAIN1 = 0, GAIN2 = 1
4
GAIN1 = 1, GAIN2 = 0
-2
GAIN1 = 1, GAIN2 = 1
1
dB
±2.5
ESD Protection
%
±8
HPOUTR, HPOUTL, IEC Air Discharge
UNITS
pF
Gain Accuracy
kV
DIGITAL INPUTS (SHDN, SYNC, HPS, GAIN_, SEL_)
Input Voltage High
VIH
Input Voltage Low
VIL
2
V
0.8
Input Leakage Current
HPS Input Current
SYNC input
±25
All other logic inputs
±1
HPS = GND
-10
V
µA
µA
Note 1: All devices are 100% production tested at +25°C. All temperature limits are guaranteed by design.
Note 2: Speaker amplifier testing performed with a resistive load in series with an inductor to simulate an actual speaker load. For
RL = 4Ω, L = 47µH. For RL = 8Ω, L = 68µH.
Note 3: Guaranteed by design, not production tested.
Note 4: PSRR is specified with the amplifier inputs connected to GND through CIN.
Typical Operating Characteristics
(VDD = 3.3V, BW = 22Hz to 22kHz, GAIN1 = 1, GAIN2 = 0, spread-spectrum mode, headphone outputs in phase.)
VDD = +5V
RL = 4Ω
RL = 4Ω
1
RL = 8Ω
1
POUT = 25mW
0.1
POUT = 100mW
0.1
0.01
POUT = 1000mW
0.001
THD+N (%)
THD+N (%)
1
0.01
100
1k
FREQUENCY (Hz)
10k
100k
POUT = 40mW
0.1
0.01
POUT = 500mW
POUT = 400mW
0.001
0.001
10
4
10
MAX9770 toc02
10
MAX9770 toc01
10
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (SPEAKER MODE)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (SPEAKER MODE)
MAX9770 toc03
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (SPEAKER MODE)
THD+N (%)
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
10
100
1k
FREQUENCY (Hz)
10k
100k
10
100
1k
FREQUENCY (Hz)
_______________________________________________________________________________________
10k
100k
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT POWER (SPEAKER MODE)
VDD = 5V
POUT = 1W
RL = 8Ω
100
MAX9770 toc05
100
MAX9770 toc04
10
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT POWER (SPEAKER MODE)
VDD = 5V
RL = 8Ω
10
MAX9770 toc06
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (SPEAKER MODE)
RL = 4Ω
10
FFM MODE
f = 20Hz
0.1
0.01
10
100
10k
1k
400
800
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT POWER (SPEAKER MODE)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT POWER (SPEAKER MODE)
f = 20Hz
0.01
SSM MODE
0.1
200
400
600
800
0
400
800
OUTPUT POWER
vs. LOAD RESISTANCE (SPEAKER MODE)
OUTPUT POWER
vs. SUPPLY VOLTAGE (SPEAKER MODE)
f = 1kHz
RL = 8Ω
THD+N = 10%
0.6
0.4
THD+N = 1%
100
EFFICIENCY vs. OUTPUT POWER
90
80
1.5
1.0
70
60
50
40
30
THD+N = 1%
0.5
0.2
10
100
EFFICIENCY (%)
OUTPUT POWER (W)
THD+N = 10%
0.50
1
MAX9770 toc11
2.0
MAX9770 toc10
0.8
THD+N = 1%
LOAD RESISTANCE (Ω)
OUTPUT POWER (mW)
f = 1kHz
0.75
1600
1200
OUTPUT POWER (mW)
1.0
1.00
0
0.001
0
THD+N = 10%
1.25
0.25
FFM MODE
0.001
VDD = 5V
f = 1kHz
RL = 8Ω
20
10
0
0
0
1
10
LOAD RESISTANCE (Ω)
100
1000
VDD = 5V
f = 1kHz
1.50
0.01
f = 10kHz
800
600
400
OUTPUT POWER (mW)
1.75
MAX9770 toc08
1
200
OUTPUT POWER
vs. LOAD RESISTANCE (SPEAKER MODE)
OUTPUT POWER (W)
f = 1kHz
VDD = 5V
f = 1kHz
RL = 8Ω
10
THD+N (%)
1
0.1
100
MAX9770 toc07
10
f = 10kHz
0
OUTPUT POWER (mW)
RL = 8Ω
OUTPUT POWER (W)
1600
1200
FREQUENCY (Hz)
100
f = 1kHz
f = 20Hz
0.1
0.001
0
100k
1
0.01
f = 10kHz
0.001
0.001
THD+N (%)
f = 1kHz
MAX9770 toc09
0.01
1
MAX9770 toc12
SSM MODE
THD+N (%)
0.1
THD+N (%)
THD+N (%)
1
2.5
3.0
3.5
4.0
4.5
SUPPLY VOLTAGE (V)
5.0
5.5
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
OUTPUT POWER (W)
_______________________________________________________________________________________
5
MAX9770
Typical Operating Characteristics (continued)
(VDD = 3.3V, BW = 22Hz to 22kHz, GAIN1 = 1, GAIN2 = 0, spread-spectrum mode, headphone outputs in phase.)
Typical Operating Characteristics (continued)
(VDD = 3.3V, BW = 22Hz to 22kHz, GAIN1 = 1, GAIN2 = 0, spread-spectrum mode, headphone outputs in phase.)
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY (SPEAKER MODE)
50
40
-40
-50
30
20
f = 1kHz
10
0.6
0.8
-120
-140
10
1.0
100
1k
10k
OUTPUT POWER (W)
FREQUENCY (Hz)
OUTPUT SPECTRUM
(SPEAKER MODE)
OUTPUT SPECTRUM
(SPEAKER MODE)
RL = 8Ω
f = 1kHz
SSM MODE
VIN = -60dBV
-20
-40
-20
-80
-60
0
-20
-80
-100
-30
-40
-50
-60
-70
-120
-140
-90
-160
-100
5
15
10
FREQUENCY (kHz)
-80
0
20
5
15
10
FREQUENCY (kHz)
1M
20
10M
100M
FREQUENCY (Hz)
STARTUP WAVEFORM
(SPEAKER MODE)
WIDEBAND OUTPUT SPECTRUM
(SPEAKER MODE)
MIXER OUTPUT
MAX9770 toc21
SSM MODE
RBW = 10kHz
-10
-20
MAX9770 toc19
MAX9770 toc20
0
SHDN
IN_1
10kHz
1V/div
IN_2
4kHz
1V/div
MONO
1kHz
2V/div
2V/div
-30
-40
-50
-60
-70
500mV/div
OUT+ - OUT-
-80
OUT
RL = 8Ω
f = 1kHz
-90
1V/div
-100
1M
10M
100M
4ms/div
400µs/div
FREQUENCY (Hz)
6
20
FFM MODE
RBW = 10kHz
-10
-120
0
15
10
FREQUENCY (kHz)
0
-100
-140
5
WIDEBAND OUTPUT SPECTRUM
(SPEAKER MODE)
RL = 8Ω
f = 1kHz
SSM MODE
A-WEIGHTED
VIN = -60dBV
-40
-60
100k
0
MAGNITUDE (dB)
0
-80
-70
MAGNITUDE (dB)
0.4
-60
-100
MAX9770 toc17
0.2
MAX9770 toc16
0
-40
-60
-80
0
MAGNITUDE (dB)
-30
MAX9770 toc18
60
MAGNITUDE (dB)
RL = 4Ω
RL = 8Ω
f = 1kHz
FFM MODE
VIN = -60dBV
-20
-20
70
PSRR (dB)
EFFICIENCY (%)
80
VRIPPLE = 200mVP-P
RL = 8Ω
-10
0
MAX9770 toc14
RL = 8Ω
90
0
MAX9770 toc13
100
OUTPUT SPECTRUM
(SPEAKER MODE)
MAX9770 toc15
EFFICIENCY vs. OUTPUT POWER
MAGNITUDE (dB)
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
_______________________________________________________________________________________
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
VDD = 5V
RL = 32Ω
RL = 16Ω
1
THD+N (%)
POUT = 10mW
0.1
THD+N (%)
1
1
POUT = 10mW
0.1
0.01
0.01
0.01
POUT = 50mW
0.001
0.001
1k
100
POUT = 35mW
POUT = 50mW
0.001
10
POUT = 10mW
0.1
10k
10
100k
1k
100
10k
10
100k
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
FREQUENCY (Hz)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (HEADPHONE MODE)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT POWER (HEADPHONE MODE)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT POWER (HEADPHONE MODE)
RL = 32Ω
VDD = 5V
RL = 16Ω
10
100
MAX9770 toc26
100
MAX9770 toc25
10
MAX9770 toc27
THD+N (%)
10
MAX9770 toc24
VDD = 5V
RL = 16Ω
MAX9770 toc23
10
MAX9770 toc22
10
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (HEADPHONE MODE)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (HEADPHONE MODE)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (HEADPHONE MODE)
VDD = 5V
RL = 32Ω
10
POUT = 10mW
0.1
THD+N (%)
THD+N (%)
THD+N (%)
1
1
f = 10kHz
f = 1kHz
0.1
1
f = 1kHz
f = 10kHz
0.1
0.01
0.01
0.01
POUT = 50mW
f = 20Hz
0.001
0.001
10
100
10k
1k
100k
20
40
60
80
100
0
20
40
60
80
FREQUENCY (Hz)
OUTPUT POWER (mW)
OUTPUT POWER (mW)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT POWER (HEADPHONE MODE)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT POWER (HEADPHONE MODE)
OUTPUT POWER
vs. LOAD RESISTANCE (HEADPHONE MODE)
1
f = 10kHz
f = 1kHz
0.1
0.01
1
f = 10kHz
f = 1kHz
0.1
0
10
30
40
OUTPUT POWER (mW)
50
60
70
THD+N = 10%
60
50
THD+N = 1%
40
30
0
0.001
20
VDD = 5V
f = 1kHz
10
f = 20Hz
f = 20Hz
90
80
20
0.01
0.001
100
MAX9770 toc30
10
THD+N (%)
10
RL = 32Ω
OUTPUT POWER (mW)
RL = 16Ω
MAX9770 toc29
100
MAX9770 toc28
100
THD+N (%)
f = 20Hz
0.001
0
0
20
40
60
OUTPUT POWER (mW)
80
10
100
1000
LOAD RESISTANCE (Ω)
_______________________________________________________________________________________
7
MAX9770
Typical Operating Characteristics (continued)
(VDD = 3.3V, BW = 22Hz to 22kHz, GAIN1 = 1, GAIN2 = 0, spread-spectrum mode, headphone outputs in phase.)
Typical Operating Characteristics (continued)
(VDD = 3.3V, BW = 22Hz to 22kHz, GAIN1 = 1, GAIN2 = 0, spread-spectrum mode, headphone outputs in phase.)
THD+N = 10%
40
THD+N = 1%
30
20
70
THD+N = 10%
60
50
40
THD+N = 1%
30
100
1000
40
30
0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
2.5
3.0
3.5
4.0
4.5
5.0
LOAD RESISTANCE (Ω)
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
POWER DISSIPATION
vs. OUTPUT POWER (HEADPHONE MODE)
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY (HEADPHONE MODE)
CROSSTALK vs. FREQUENCY
(HEADPHONE MODE)
-10
-20
PSRR (dB)
-40
150
100
-50
-60
RL = 32Ω
50
f = 1kHz
POUT = POUTL + POUTR
0
30
60
90
120
-70
-80
-80
-90
-100
-100
10
100
1k
10k
10
100k
100
1k
10k
OUTPUT POWER
vs. CHARGE-PUMP CAPACITANCE
OUTPUT SPECTRUM
(HEADPHONE MODE)
60
C1 = C2 = 1µF
50
40
C1 = C2 = 0.47µF
30
20
10
1k
FREQUENCY (Hz)
10k
100k
-40
-60
-80
-120
f = 1kHz
THD+N = 1%
0
100
RL = 32Ω
f = 1kHz
VIN = -60dBV
-20
100k
-100
SPEAKER MODE
-100
0
MAGNITUDE (dB)
MAX9770 toc37
-80
10
RIGHT TO LEFT
FEEDTHROUGH vs. FREQUENCY
HEADPHONE MODE
-90
LEFT TO RIGHT
FREQUENCY (Hz)
-50
-70
-60
-70
150
-40
-60
-50
-90
OUTPUT POWER (mW)
-30
-40
FREQUENCY (Hz)
SEL1 = 0
SEL2 = 1
IN1_ = GND
IN2_ = DRIVEN
VIN = 2VP-P
-20
-30
OUTPUT POWER (mW)
0
-10
-20
MAX9770 toc38
0
RL = 32Ω
f = 1kHz
VIN = 200mVP-P
-10
CROSSTALK (dB)
-30
RL = 16Ω
200
VDD = 5V
VRIPPLE = 200mVP-P
RL = 32Ω
5.5
MAX9770 toc36
250
0
MAX9770 toc35
0
MAX9770 toc34
300
POWER DISSIPATION (mW)
THD+N = 1%
50
0
10
8
60
10
10
0
THD+N = 10%
20
20
10
RL = 32Ω
f = 1kHz
70
MAX9770 toc33
80
OUTPUT POWER (mW)
OUTPUT POWER (mW)
60
80
OUTPUT POWER (mW)
70
RL = 16Ω
f = 1kHz
90
OUTPUT POWER
vs. SUPPLY VOLTAGE (HEADPHONE MODE)
MAX9770 toc32
f = 1kHz
50
100
MAX9770 toc31
80
OUTPUT POWER
vs. SUPPLY VOLTAGE (HEADPHONE MODE)
MAX9770 toc39
OUTPUT POWER
vs. LOAD RESISTANCE (HEADPHONE MODE)
FEEDTHROUGH (dB)
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
20
30
40
LOAD (Ω)
-140
50
0
5
10
15
FREQUENCY (kHz)
_______________________________________________________________________________________
20
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
EXITING SHUTDOWN
(HEADPHONE MODE)
ENTERING SHUTDOWN
(HEADPHONE MODE)
MAX9770 toc40
MAX9770 toc41
RL = 32Ω
RL = 32Ω
SHDN
2V/div
SHDN
2V/div
OUT_
10mV/div
OUT_
10mV/div
2µs/div
2µs/div
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
SHUTDOWN SUPPLY CURRENT
vs. SUPPLY VOLTAGE
6
HEADPHONE MODE
4
0.4
SUPPLY CURRENT (µA)
SPEAKER MODE
MAX9770 toc43
8
SUPPLY CURRENT (mA)
0.5
MAX9770 toc42
10
0.3
0.2
0.1
2
0
0
2.5
3.5
4.5
5.5
2.5
3.5
4.5
5.5
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Pin Description
PIN
TQFN
1
TSSOP
4
2
3
NAME
FUNCTION
BIAS
Common-Mode Bias Voltage. Bypass with a 0.047µF capacitor to GND.
5
VDD
Power Supply
6
HPOUTR
Right-Channel Headphone Output
4
7
HPOUTL
Left-Channel Headphone Output
5
8
SVSS
Headphone Amplifier Negative Power Supply
6
9
HPS
Headphone Sense Input
_______________________________________________________________________________________
9
MAX9770
Typical Operating Characteristics (continued)
(VDD = 3.3V, BW = 22Hz to 22kHz, GAIN1 = 1, GAIN2 = 0, spread-spectrum mode, headphone outputs in phase.)
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
Pin Description (continued)
PIN
NAME
FUNCTION
TQFN
7
TSSOP
10
CPVDD
Positive Charge-Pump Power Supply
8
11
CPVSS
Charge-Pump Output. Connect to SVSS.
9
12
C1N
Charge-Pump Flying Capacitor Negative Terminal
Charge-Pump Flying Capacitor Positive Terminal
10
13
C1P
11
14
CPGND
12
15
SEL1
Select Stereo Channel 1 Inputs. Digital input. Drive SEL1 high to select inputs IN1_L and
IN1_R.
13
16
SEL2
Select Stereo Channel 2 Inputs. Digital input. Drive SEL2 high to select inputs IN2_L and
IN2_R.
14
17
SELM
Select Mono Channel Input. Digital input. Drive SELM high to select the MONO input.
15
18
SHDN
Shutdown. Drive SHDN low to disable the device. Connect SHDN to VDD for normal
operation.
Charge-Pump Ground
16
19
SYNC
Frequency Select and External Clock Input.
SYNC = GND: fixed-frequency PWM mode with fS = 1100kHz.
SYNC = Float: fixed-frequency PWM mode with fS = 1450kHz.
SYNC = VDD: spread-spectrum PWM mode with fS = 1220kHz ± 120kHz.
SYNC = Clocked: fixed-frequency PWM mode with fS = external clock frequency.
17
20
PGND
Speaker Amplifier Power Ground
18
21
OUT+
Speaker Amplifier Positive Output
19
22
OUT-
Speaker Amplifier Negative Output
20
23
PVDD
Speaker Amplifier Power Supply
21
24
GAIN2
Gain Control Input 2
22
25
GAIN1
Gain Control Input 1
23
26
MONO
Mono Channel Input
24
27
IN2_L
Stereo Channel 2, Left Input
25
28
IN1_L
Stereo Channel 1, Left Input
26
1
GND
Ground
27
2
IN2_R
Stereo Channel 2, Right Input
28
3
IN1_R
EP
—
EP
Stereo Channel 1, Right Input
Exposed Paddle. Can be left floating or tied to GND.
Detailed Description
The MAX9770 combines a mono 1.2W Class D speaker
amplifier and stereo 80mW DirectDrive headphone
amplifiers with integrated headphone sensing and
comprehensive click-and-pop suppression. A
mixer/multiplexer allows for selection and mixing
between two stereo input sources and a single mono
source. The MAX9770 features a high 80dB PSRR, low
0.015% THD+N, industry-leading click/pop performance, and a low-power shutdown mode.
10
Class D Speaker Amplifier
The MAX9770 Class D amplifier features a true filterless, low EMI, switch-mode architecture that provides
Class AB-like performance with Class D efficiency.
Comparators monitor the MAX9770 input and compare
the input voltage to a sawtooth waveform. The comparators trip when the input magnitude of the sawtooth
exceeds the corresponding input voltage. The comparator resets at a fixed time after the rising edge of the
second comparator trip point, generating a minimum-
______________________________________________________________________________________
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
Operating Modes
The switching frequency of the charge pump is 1/2 the
switching frequency of the Class D amplifier, regardless of the operating mode. When SYNC is driven externally, the charge pump switches at 1/2 fSYNC. When
SYNC = VDD, the charge pump switches with a spreadspectrum pattern.
Table 1. Operating Modes
SYNC INPUT
MODE
GND
FFPWM with fS = 1100kHz
FLOAT
FFPWM with fS = 1450kHz
VDD
Clocked
SSPWM with fS = 1220kHz ±120kHz
FFPWM with fS = external clock frequency
Fixed-Frequency Modulation (FFM) Mode
The MAX9770 features two FFM modes. The FFM
modes are selected by setting SYNC = GND for a
1.1MHz switching frequency, and SYNC = FLOAT for a
1.45MHz switching frequency. In FFM mode, the frequency spectrum of the Class D output consists of the
tSW
VIN-
VIN+
OUT-
OUT+
tON(MIN)
VOUT+ - VOUT-
Figure 1. MAX9770 Outputs with an Input Signal Applied
______________________________________________________________________________________
11
MAX9770
width pulse tON(min) at the output of the second comparator (Figure 1). As the input voltage increases or
decreases, the duration of the pulse at one output
increases (the first comparator trip point) while the
other output pulse duration remains at tON(min). This
causes the net voltage across the speaker (VOUT+ VOUT-) to change.
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
fundamental switching frequency and its associated
harmonics (see the Wideband FFT graph in the Typical
Operating Characteristics). The MAX9770 allows the
switching frequency to be changed by +32% should
the frequency of one or more harmonics fall in a sensitive band. This can be done during operation and does
not affect audio reproduction.
Spread-Spectrum Modulation (SSM) Mode
The MAX9770 features a unique, patented spreadspectrum mode that flattens the wideband spectral
components, improving EMI emissions radiated by the
speaker and cables by 5dB. Proprietary techniques
tSW
tSW
ensure that the cycle-to-cycle variation of the switching
period does not degrade audio reproduction or efficiency (see the Typical Operating Characteristics).
Select SSM mode by setting SYNC = V DD . In SSM
mode, the switching frequency varies randomly by
±120kHz around the center frequency (1.22MHz). The
modulation scheme remains the same, but the period
of the sawtooth waveform changes from cycle-to-cycle
(Figure 2). Instead of a large amount of spectral energy
present at multiples of the switching frequency, the
energy is now spread over a bandwidth that increases
with frequency. Above a few MHz, the wideband spectrum looks like white noise for EMI purposes (Figure 3).
tSW
tSW
VIN-
VIN+
OUT-
OUT+
tON(MIN)
VOUT+ - VOUT-
Figure 2. MAX9770 Output with an Input Signal Applied (SSM mode)
12
______________________________________________________________________________________
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
MAX9770
50.0
AMPLITUDE (dBµV/m)
45.0
40.0
35.0
30.0
25.0
20.0
15.0
10.0
30.0
60.0
80.0 100.0 120.0 140.0 160.0 180.0 200.0 220.0 240.0 260.0 280.0 300.0
FREQUENCY (MHz)
Figure 3. MAX9770 EMI with 75mm of Speaker Cable
synchronizes the switching frequency of both the Class
D and charge pump. The period of the SYNC clock can
be randomized, enabling the MAX9770 to be synchronized to another spread-spectrum Class D amplifier
operating in SSM mode.
VIN = 0V
Filterless Modulation/Common-Mode Idle
The MAX9770 uses Maxim’s unique, patented modulation
scheme that eliminates the LC filter required by traditional
Class D amplifiers, improving efficiency, reducing component count, conserving board space and system cost.
Conventional Class D amplifiers output a 50% duty cycle
square wave when no signal is present. With no filter, the
square wave appears across the load as a DC voltage,
resulting in finite load current, increasing power consumption. When no signal is present at the device input,
the outputs switch as shown in Figure 4. Because the
MAX9770 drives the speaker differentially, the two outputs cancel each other, resulting in no net idle mode voltage across the speaker, minimizing power consumption.
OUT-
OUT+
VOUT+ - VOUT- = 0V
Figure 4. MAX9770 Output with No Signal Applied
External Clock Mode
The SYNC input allows the MAX9770 to be synchronized to a system clock (allowing a fully synchronous
system), or allocating the spectral components of the
switching harmonics to insensitive frequency bands.
Applying an external clock of 800kHz to 2MHz to SYNC
Efficiency
Efficiency of a Class D amplifier is attributed to the
region of operation of the output stage transistors. In a
Class D amplifier, the output transistors act as currentsteering switches and consume negligible additional
power. Any power loss associated with the Class D output stage is mostly due to the I*R loss of the MOSFET
on-resistance, and quiescent current overhead.
______________________________________________________________________________________
13
The theoretical best efficiency of a linear amplifier is
78%; however, that efficiency is only exhibited at peak
output powers. Under normal operating levels (typical
music reproduction levels), efficiency falls below 30%,
whereas the MAX9770 still exhibits >80% efficiencies
under the same conditions (Figure 5).
DirectDrive
Traditional single-supply headphone drivers have their
outputs biased about a nominal DC voltage (typically
half the supply) for maximum dynamic range. Large
coupling capacitors are needed to block this DC bias
from the headphone. Without these capacitors, a significant amount of DC current flows to the headphone,
resulting in unnecessary power dissipation and possible damage to both headphone and headphone driver.
Maxim’s patented DirectDrive architecture uses a charge
pump to create an internal negative supply voltage. This
allows the headphone outputs of the MAX9770 to be
biased about GND, almost doubling dynamic range
while operating from a single supply. With no DC component, there is no need for the large DC-blocking capacitors. Instead of two large (220µF, typ) tantalum
capacitors, the MAX9770 charge pump requires two
small ceramic capacitors, conserving board space,
reducing cost, and improving the frequency response of
the headphone driver. See the Output Power vs. ChargePump Capacitance and Load Resistance graph in the
Typical Operating Characteristics for details of the possible capacitor sizes. There is a low DC voltage on the driver outputs due to amplifier offset. However, the offset of
the MAX9770 is typically 5mV, which, when combined
with a 32Ω load, results in less than 160µA of DC current
flow to the headphones.
In addition to the cost and size disadvantages of the DCblocking capacitors required by conventional headphone amplifiers, these capacitors limit the amplifier’s
low-frequency response and can distort the audio signal.
Previous attempts at eliminating the output-coupling
capacitors involved biasing the headphone return
(sleeve) to the DC bias voltage of the headphone
amplifiers. This method raises some issues:
1) When combining a microphone and headphone on
a single connector, the microphone bias scheme
typically requires a 0V reference.
2) The sleeve is typically grounded to the chassis.
Using the midrail biasing approach, the sleeve must
be isolated from system ground, complicating product design.
3) During an ESD strike, the driver’s ESD structures are
the only path to system ground. Thus, the driver
must be able to withstand the full ESD strike.
14
EFFICIENCY vs. OUTPUT POWER
100
90
80
EFFICIENCY (%)
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
70
MAX9770
60
50
40
30
CLASS AB
20
VDD = 3.3V
f = 1kHz
RL - 8Ω
10
0
0
0.1
0.2
0.3
0.4
0.5
0.6
OUTPUT POWER (W)
Figure 5. MAX9770 Efficiency vs. Class AB Efficiency
4) When using the headphone jack as a line out to
other equipment, the bias voltage on the sleeve may
conflict with the ground potential from other equipment, resulting in possible damage to the drivers.
Charge Pump
The MAX9770 features a low-noise charge pump. The
switching frequency of the charge pump is 1/2 the
switching frequency of the Class D amplifier, regardless
of the operating mode. When SYNC is driven externally,
the charge pump switches at 1/2 fSYNC. When SYNC =
VDD, the charge pump switches with a spread-spectrum
pattern. The nominal switching frequency is well beyond
the audio range, and thus does not interfere with the
audio signals, resulting in an SNR of 101dB. The switch
drivers feature a controlled switching speed that minimizes noise generated by turn-on and turn-off transients. By limiting the switching speed of the charge
pump, the di/dt noise caused by the parasitic bond wire
and trace inductance is minimized. Although not typically required, additional high-frequency noise attenuation
can be achieved by increasing the size of C2 (see
Typical Application Circuit). The charge pump is active
in both speaker and headphone modes.
Input Multiplexer/Mixer
The MAX9770 features an input multiplexer/mixer that
allows three different audio sources to be selected/
mixed. Driving a SEL_ input high selects the input channel (see Table 2), and the audio signal is output to the
active amplifier. When a stereo path is selected in
speaker mode (SEL1 or SEL2 = 1), the left and right
______________________________________________________________________________________
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
MAX9770
Table 2. Multiplexer/Mixer Settings
SEL1
HEADPHONE MODE
SEL2 SELM
HPOUTL
SPEAKER MODE
HPOUTR
0
0
0
MUTE
MUTE
MUTE
1
0
0
IN1_L
IN1_R
(IN1_L + IN1_R) / 2
0
1
0
IN2_L
IN2_R
(IN2_L + IN2_R) / 2
0
0
1
MONO
MONO
MONO
1
1
0
(IN1_L + IN2_L) / 2
(IN1_R + IN2_R) / 2
(IN1_L + IN1_R + IN2_L + IN2_R) / 4
1
0
1
(IN1_L + MONO) /2
(IN1_R + MONO) / 2
(IN1_L + IN1_R + MONO x 2) / 4
0
1
1
(IN2_L + MONO) / 2
(IN2_R + MONO) / 2
(IN2_L + IN2_R + MONO x 2) / 4
1
1
1
(IN1_L + IN2_L + MONO) / 3
(IN1_R + IN2_R + MONO) / 3
(IN1_L + IN1_R + IN2_L + IN2_R + MONO x 2) / 6
inputs are attenuated by 6dB and mixed together, resulting in a true mono reproduction of a stereo signal. When
more than one signal path is selected, the sources are
attenuated before mixing to preserve overall amplitude.
Selecting two sources results in 6dB attenuation, selecting three sources results in 9.5dB attenuation.
Headphone Sense Input (HPS)
The headphone sense input (HPS) monitors the headphone jack, and automatically configures the device
based upon the voltage applied at HPS. A voltage of
less than 0.8V sets the device to speaker mode. A voltage of greater than 2V disables the bridge amplifiers
and enables the headphone amplifiers.
For automatic headphone detection, connect HPS to
the control pin of a 3-wire headphone jack as shown in
Figure 6. With no headphone present, the output
impedance of the headphone amplifier pulls HPS to
less than 0.8V. When a headphone plug is inserted into
the jack, the control pin is disconnected from the tip
contact and HPS is pulled to VDD through the internal
800kΩ pullup. When driving HPS from an external logic
source, ground HPS when the MAX9770 is shut down.
Place a 10kΩ resistor in series with HPS and the headphone jack to ensure ±8kV ESD protection.
Table 2 shows the output amplitude of the selected
channels multiplied by the gain.
BIAS
The MAX9770 features an internally generated, powersupply independent, common-mode bias voltage referenced to GND. BIAS provides both click-and-pop
suppression and sets the DC bias level for the amplifiers.
Choose the value of the bypass capacitor as described
in the BIAS Capacitor section. No external load should
be applied to BIAS. Any load lowers the BIAS voltage,
affecting the overall performance of the device.
VDD
MAX9770
800kΩ
SHUTDOWN
CONTROL
HPS
HPOUTL
HPOUTR
10kΩ
10kΩ
Figure 6. HPS Configuration
Gain Selection
The MAX9770 features a logic-selectable, internally set
gain. GAIN1 and GAIN2 set the gain of the MAX9770
speaker and headphone amplifiers as shown in Table 3.
The MAX9770 can be configured to automatically
switch between two gain settings depending on
whether the device is in speaker or headphone mode.
By driving one or both gain inputs with HPS, the gain of
the device changes when a headphone is inserted or
removed. For example, the block diagram shows HPS
connected to GAIN2, while GAIN1 is connected to VDD.
In this configuration, the gain in speaker mode is 9dB,
while the gain in headphone mode is 1dB. The gain
settings with the HPS connection are shown in Table 4.
______________________________________________________________________________________
15
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
Table 3. Gain Selection
HEADPHONE
GAIN
(dB)
SPEAKER
OUTPUT
POWER
(VIN = 0.707VRMS)
(mW)
SPEAKER
OUTPUT
POWER
(VIN = 1VRMS)
(mW)
HEADPHONE
OUTPUT
POWER
(VIN = 0.707VRMS)
(mW)
HEADPHONE
OUTPUT
POWER
(VIN = 1VRMS)
(mW)
7
500 / 4Ω
500 / 8Ω
60* / 32Ω
60* / 32Ω
60* / 32Ω
GAIN1
GAIN2
SPEAKER
GAIN
(dB)
0
0
6
0
1
3
4
250 / 4Ω
500 / 4Ω
78 / 16Ω
1
0
9
-2
500 / 8Ω
1000 / 8Ω
19 / 16Ω
39 / 16Ω
1
1
0
1
124 / 4Ω
250 / 4Ω
39 / 16Ω
78 / 16Ω
*Output power limited to 60mW due to output voltage swing.
Table 4. Gain Settings with HPS
Connection
GAIN1
GAIN2
SPEAKER MODE
GAIN
(HPS = 0)
HEADPHONE
MODE GAIN
(HPS = 1)
HPS
0
6
-2
HPS
1
3
1
0
HPS
6
4
1
HPS
9
1
HPS
HPS
6
1
0
0
6
7
0
1
3
4
1
0
9
-2
1
1
0
1
Shutdown
The MAX9770 features a 0.1µA, low-power shutdown
mode that reduces quiescent current consumption and
extends battery life. Drive SHDN low to disable the
drive amplifiers, bias circuitry, and charge pump. Bias
is driven to GND and the headphone amplifier output
impedance is 10kΩ in shutdown. Connect SHDN to
VDD for normal operation.
Headphone Amplifier
In conventional single-supply headphone drivers, the
output-coupling capacitor is a major contributor of
audible clicks and pops. Upon startup, the driver
charges the coupling capacitor to its bias voltage, typically half the supply. Likewise, during shutdown, the
capacitor is discharged to GND. This results in a DC
shift across the capacitor, which in turn, appears as an
audible transient at the speaker. Since the MAX9770
headphone amplifier does not require output-coupling
capacitors, this does not arise.
Additionally, the MAX9770 features extensive click-andpop suppression that eliminates any audible transient
sources internal to the device. The Power-Up/PowerDown Waveform in the Typical Operating Characteristics
shows that there are minimal spectral components in the
audible range at the output upon startup or shutdown.
In most applications, the output of the preamplifier driving the MAX9770 has a DC bias of typically half the
supply. During startup, the input-coupling capacitor is
charged to the preamplifier’s DC bias voltage through
the RF of the MAX9770, resulting in a DC shift across the
capacitor and an audible click/pop. An internal delay of
50ms eliminates the click/pop caused by the input filter.
Applications Information
Click-and-Pop Suppression
Filterless Operation
Speaker Amplifier
The MAX9770 speaker amplifier features comprehensive
click-and-pop suppression that eliminates audible transients on startup and shutdown. While in shutdown, the
H-bridge is in a high-impedance state. During startup or
power-up, the input amplifiers are muted and an internal
loop sets the modulator bias voltages to the correct levels, preventing clicks and pops when the H-bridge is
subsequently enabled. For 30ms following startup, a
soft-start function gradually unmutes the input amplifiers.
Traditional Class D amplifiers require an output filter to
recover the audio signal from the amplifier’s output. The
filters add cost, increase the solution size of the amplifier, and can decrease efficiency. The traditional PWM
scheme uses large differential output swings (2 x VDD
peak-to-peak) at idle and causes large ripple currents.
Any parasitic resistance in the filter components results
in a loss of power, lowering efficiency.
16
______________________________________________________________________________________
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
Output Offset
Unlike Class AB amplifiers, the output offset voltage of a
Class D amplifier does not noticeably increase quiescent
current draw when a load is applied. This is due to the
power conversion of the Class D amplifier. For example, a
15mV DC offset across an 8Ω load results in 1.9mA extra
current consumption in a Class AB device. In the Class D
case, a 15mV offset into 8Ω equates to an additional
power drain of 28µW. Due to the high efficiency of the
Class D amplifier, this represents an additional quiescent
current draw of 28µW/(VDD / 100 x η), which is on the
order of a few microamps.
Power Supplies
The MAX9770 has different supplies for each portion of
the device, allowing for the optimum combination of
headroom and power dissipation and noise immunity.
The speaker amplifiers are powered from PVDD. PVDD
ranges from 2.5V to 5.5V. The headphone amplifiers
are powered from VDD and SVSS. VDD is the positive
supply of the headphone amplifiers and ranges from
2.5V to 5.5V. SVSS is the negative supply of the headphone amplifiers. Connect SVSS to CPVSS. The charge
pump is powered by CPVDD. CPVDD ranges from 2.5V
to 5.5V and should be the same potential as VDD. The
charge pump inverts the voltage at CPVDD, and the
resulting voltage appears at CPVSS. The remainder of
the device is powered by VDD.
Component Selection
removes the DC bias from an incoming signal (see the
Typical Application Circuit). The AC-coupling capacitor
allows the amplifier to bias the signal to an optimum DC
level. Assuming zero-source impedance, the -3dB point
of the highpass filter is given by:
f−3dB =
1
2πRINCIN
RIN is the amplifier’s internal input resistance value
given in the Electrical Characteristics. Be aware that
the MONO input has a higher input impedance than the
other inputs. Choose CIN such that f-3dB is below the
lowest frequency of interest. Setting f -3dB too high
affects the amplifier’s low-frequency response. Setting
f-3dB too low can affect the click-and-pop performance.
Use capacitors with low-voltage coefficient dielectrics,
such as tantalum or aluminum electrolytic. Capacitors
with high-voltage coefficients, such as ceramics, may
result in increased distortion at low frequencies.
Output Filter
The MAX9770 speaker amplifier does not require an output filter for normal operation and audio reproduction. The
device passes FCC Class B radiated emissions standards with 100mm of unshielded speaker cables.
However, output filtering can be used if a design is failing
radiated emissions due to board layout or cable length,
or if the circuit is near EMI-sensitive devices. Use a common-mode choke connected in series with the speaker
outputs if board space is limited and emissions are a
concern. Use of an LC filter is necessary if excessive
speaker cable is used.
BIAS Capacitor
BIAS is the output of the internally generated DC bias
voltage. The BIAS bypass capacitor, CBIAS improves
PSRR and THD+N by reducing power supply and other
noise sources at the common-mode bias node, and
also generates the clickless/popless, startup/shutdown
DC bias waveforms for the speaker amplifiers. Bypass
BIAS with a 0.047µF capacitor to GND. Large values of
CBIAS result in poor click/pop performance, and smaller values of CBIAS result in degradation of PSRR and
increased output noise.
Input Filter
The input capacitor (CIN), in conjunction with the amplifier input resistance (RIN), forms a highpass filter that
______________________________________________________________________________________
17
MAX9770
The MAX9770 does not require an output filter. The
device relies on the inherent inductance of the speaker
coil and the natural filtering of both the speaker and the
human ear to recover the audio component of the
square-wave output. Eliminating the output filter results
in a smaller, less costly, and more efficient solution.
Because the frequency of the MAX9770 output is well
beyond the bandwidth of most speakers, voice coil
movement due to the square-wave frequency is minimal. Although this movement is small, a speaker not
designed to handle the additional power may be damaged. For optimum results, use a speaker with a series
inductance >10µH. Typical small 8Ω speakers exhibit
series inductances in the range of 20µH to 100µH.
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
Table 5. Suggested Capacitor Manufacturers
SUPPLIER
Taiyo Yuden
TDK
PHONE
800-348-2496
807-803-6100
FAX
847-925-0899
847-390-4405
Charge-Pump Capacitor Selection
Use capacitors with an ESR less than 100mΩ for optimum performance. Low-ESR ceramic capacitors minimize the output resistance of the charge pump. Most
surface-mount ceramic capacitors satisfy the ESR
requirement. For best performance over the extended
temperature range, select capacitors with an X7R
dielectric. Table 5 lists suggested manufacturers.
Flying Capacitor (C1)
The value of the flying capacitor (C1) affects the load
regulation and output resistance of the charge pump. A
C1 value that is too small degrades the device’s ability to
provide sufficient current drive, which leads to a loss of
output voltage. Increasing the value of C1 may improve
load regulation and reduces the charge-pump output
resistance to an extent. Above 1µF, the on-resistance of
the switches and the ESR of C1 and C2 dominate.
Output Capacitor (C2)
The output capacitor value and ESR directly affect the
ripple at CPVSS. Increasing the value of C2 reduces
output ripple. Likewise, decreasing the ESR of C2
reduces both ripple and output resistance. Lower
capacitance values can be used in systems with low
maximum output power levels. See the Output Power
vs. Charge Pump Capacitance and Load Resistance
graph in the Typical Operating Characteristics.
CPVDD Bypass Capacitor
The CPVDD bypass capacitor (C3) lowers the output
impedance of the power supply and reduces the
impact of the MAX9770’s charge-pump switching transients. Bypass CPVDD with C3, the same value as C1,
and place it physically close to the CPVDD and PGND
(refer to the MAX9770 EV kit for a suggested layout).
18
WEBSITE
www.t-yuden.com
www.component.tdk.com
Layout and Grounding
Proper layout and grounding are essential for optimum
performance. Use large traces for the power-supply
inputs and amplifier outputs to minimize losses due to
parasitic trace resistance, as well as route the head
away from the device. Good grounding improves audio
performance, minimizes crosstalk between channels,
and prevents any switching noise from coupling into
the audio signal. Connect CPGND, PGND, and GND
together at a single point on the PC board. Route
CPGND and all traces that carry switching transients
away from GND, PGND, and the traces and components in the audio signal path.
Connect all components associated with the charge
pump (C2 and C3) to the CPGND plane. Connect SVSS
and CPVSS together at the device. Place the chargepump capacitors (C1, C2, and C3) as close to the
device as possible. Bypass VDD and PVDD with a 1µF
capacitor to GND. Place the bypass capacitors as
close to the device as possible.
Use large, low-resistance output traces. As load impedance decreases, the current drawn from the device outputs increase. At higher current, the resistance of the
output traces decrease the power delivered to the load.
Large output, supply, and GND traces also improve the
power dissipation of the device.
The MAX9770 thin QFN package features an exposed
thermal pad on its underside. This pad lowers the package’s thermal resistance by providing a direct heat conduction path. Due to the high efficiency of the MAX9770’s
Class D amplifier, additional heatsinking is not required. If
additional heatsinking is required, connect the exposed
paddle to GND. See the MAX9770 EV kit data sheet for
suggested component values and layout guidelines.
______________________________________________________________________________________
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
2.5V TO 5.5V
1µF
VDD
2
(5)
16
SYNC (19)
VDD
LEFT-CHANNEL
AUDIO INPUT 1
RIGHT-CHANNEL
AUDIO INPUT 1
MONO
AUDIO INPUT
LEFT-CHANNEL
AUDIO INPUT 2
CIN
0.47µF
25
IN1_L (28)
CIN
0.47µF
28
IN1_R (3)
CIN
0.47µF
23
MONO (26)
CIN
0.47µF
24
IN2_L (27)
OSCILLATOR
CLASS D
MODULATOR
21
HPS GAIN2 (24)
22
GAIN1 (25)
VDD
14
(17)
SELM
VDD
12
SEL1 (15)
GND
13
SEL2 (16)
GND
15
SHDN (18)
VDD
H-BRIDGE
MIXER/
MUX/GAIN
CONTROL
2.5V TO 5.5V
0.1µF
18
(21) OUT+
19
(22) OUT17
(20) PGND
1
(4) BIAS
CBIAS
0.047µF
VDD
27
IN2_R (2)
CIN
0.47µF
RIGHT-CHANNEL
AUDIO INPUT 2
20
(23) PVDD
6
(9) HPS
MUX AND
GAIN CONTROL
4
(7) HPOUTL
HEADPHONE
DETECTION
3
(6) HPOUTR
SHUTDOWN
CONTROL
7
CPVDD (10)
VDD
10
C1P (13)
1µF
C1
1µF
9
(12)
MAX9770
CHARGE
PUMP
OSC/2
C1N
11
CPGND (14)
8
(11)
CPVSS
26
(1)
5
(8)
SVSS
GND
C2
1µF
( ) TSSOP PIN.
______________________________________________________________________________________
19
MAX9770
Block Diagram
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
MAX9770
System Diagram
2.5V TO 5.5V
1µF
1µF
VDD
PVDD
0.47µF
OUT+
IN1_R
MP3 DAC
OUTIN1_L
0.47µF
MAX9770
HPOUTL
0.47µF
HPS
IN2_R
HPOUTR
FM RADIO
MODULE
IN2_L
0.47µF
CPVSS
VSS
0.47µF
CPGND
MONO
C1P
BASEBAND
PROCESSOR
SHDN
SEL1
SEL2
SELM
VDD
GAIN1
VDD
GAIN2
1µF
1µF
C1N
CPVDD
2.5V TO 5.5V
BIAS
0.047µF
GND
20
1µF
PGND
______________________________________________________________________________________
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
IN1_R
IN2_R
GND
IN1_L
IN2_L
MONO
GAIN1
28
27
26
25
24
23
22
TOP VIEW
GND 1
28 IN1_L
IN2_R 2
27 IN2_L
IN1_R 3
26 MONO
BIAS 4
25 GAIN1
BIAS
1
21
GAIN2
VDD 5
24 GAIN2
VDD
2
20
PVDD
HPOUTR
3
19
OUT-
HPOUTL
4
18
OUT+
HPOUTR 6
MAX9770
23 PVDD
HPOUTL 7
22 OUT-
SVSS 8
21 OUT+
HPS 9
20 PGND
SVSS
5
17
PGND
CPVDD 10
19 SYNC
HPS
6
16
SYNC
CPVSS 11
18 SHDN
CPVDD
7
15
SHDN
C1N 12
17 SELM
C1P 13
16 SEL2
CPGND 14
15 SEL1
TSSOP
13
14
SELM
11
CPGND
SEL2
10
C1P
12
9
C1N
SEL1
8
CPVSS
MAX9770
TQFN
Chip Information
TRANSISTOR COUNT: 7020
PROCESS: BiCMOS
______________________________________________________________________________________
21
MAX9770
Pin Configurations
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
D2
0.15 C A
D
b
CL
0.10 M C A B
D2/2
D/2
PIN # 1
I.D.
QFN THIN.EPS
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
k
0.15 C B
PIN # 1 I.D.
0.35x45∞
E/2
E2/2
CL
(NE-1) X e
E
E2
k
L
DETAIL A
e
(ND-1) X e
DETAIL B
e
L1
L
CL
CL
L
L
e
e
0.10 C
A
C
A1
0.08 C
A3
PACKAGE OUTLINE
16, 20, 28, 32, 40L, THIN QFN, 5x5x0.8mm
21-0140
E
1
2
Note: The MAX9770 thin QFN package features an exposed thermal pad on its underside. This pad lowers the package’s thermal resistance by providing a direct heat conduction path. Due to the high efficiency of the MAX9770’s Class D amplifier, additional
heatsinking is not required. The voltage of the exposed paddle is -VDD and it is important that the exposed paddle is NOT connected to the ground plane. It should be either left floating or can be tied to the CPVSS pin. See the MAX9770 EV kit data sheet for
suggested component values and layout guidelines.
22
______________________________________________________________________________________
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
COMMON DIMENSIONS
EXPOSED PAD VARIATIONS
PKG.
16L 5x5
20L 5x5
28L 5x5
32L 5x5
40L 5x5
SYMBOL MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX.
A
A1
A3
b
D
E
L1
0
0.20 REF.
0.02 0.05
0
0.20 REF.
0.02 0.05
0
0.02 0.05
0.20 REF.
0.20 REF.
0
-
0.05
0.20 REF.
0.25 0.30 0.35 0.25 0.30 0.35 0.20 0.25 0.30 0.20 0.25 0.30 0.15 0.20 0.25
4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10
4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10
e
k
L
0.02 0.05
0.65 BSC.
0.80 BSC.
0.50 BSC.
0.50 BSC.
0.40 BSC.
- 0.25 - 0.25
- 0.25 0.35 0.45
0.25 - 0.25 0.30 0.40 0.50 0.45 0.55 0.65 0.45 0.55 0.65 0.30 0.40 0.50 0.40 0.50 0.60
-
-
-
-
-
N
ND
NE
16
4
4
20
5
5
JEDEC
WHHB
WHHC
-
-
-
-
-
-
WHHD-1
-
0.30 0.40 0.50
32
8
8
40
10
10
WHHD-2
-
28
7
7
E2
DOWN
BONDS
MIN.
NOM. MAX.
T1655-1
T1655-2
3.00
3.00
3.10 3.20 3.00
3.10 3.20 3.00
3.10 3.20
3.10 3.20
T2055-2
T2055-3
3.00
3.00
3.10 3.20 3.00
3.10 3.20 3.00
3.10 3.20
3.10 3.20
T2055-4
T2855-1
T2855-2
T2855-3
T2855-4
T2855-5
T2855-6
T2855-7
T3255-2
T3255-3
T3255-4
3.00
3.15
2.60
3.15
2.60
2.60
3.15
2.60
3.00
3.00
3.00
3.10
3.25
2.70
3.25
2.70
2.70
3.25
2.70
3.10
3.10
3.10
3.10
3.25
2.70
3.25
2.70
2.70
3.25
2.70
3.10
3.10
3.10
T4055-1
3.20
3.30 3.40 3.20
0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80
0
D2
PKG.
CODES
3.20
3.35
2.80
3.35
2.80
2.80
3.35
2.80
3.20
3.20
3.20
MIN.
3.00
3.15
2.60
3.15
2.60
2.60
3.15
2.60
3.00
3.00
3.00
NOM. MAX. ALLOWED
3.20
3.35
2.80
3.35
2.80
2.80
3.35
2.80
3.20
3.20
3.20
3.30 3.40
NO
YES
NO
YES
NO
NO
NO
YES
YES
NO
NO
YES
NO
YES
NO
YES
NOTES:
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1
SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE
ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE.
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.25 mm AND 0.30 mm
FROM TERMINAL TIP.
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220, EXCEPT EXPOSED PAD DIMENSION FOR T2855-1,
T2855-3 AND T2855-6.
10. WARPAGE SHALL NOT EXCEED 0.10 mm.
PACKAGE OUTLINE
16, 20, 28, 32, 40L, THIN QFN, 5x5x0.8mm
21-0140
E
2
2
______________________________________________________________________________________
23
MAX9770
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
TSSOP4.40mm.EPS
MAX9770
1.2W Low-EMI, Filterless, Mono Class D Amplifier
with Stereo DirectDrive Headphone Amplifiers
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
24 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2004 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.