ICM532B CIF Color CMOS Sensor with USB Output Outline Spec, V 1.1 November, 2002 ICM532B CIF Color CMOS Image Sensor With USB Output Outline Specification V1.1 November, 2002 IC Media Corporation IC Media Technology Corporation 545 East Brokaw Road San Jose, CA 95112, U.S.A. Phone: (408) 451-8838 Fax: (408) 451-8839 Email: [email protected] Web Site: www.ic-media.com 6F, No. 61, ChowTze Street., NeiHu District Taipei, Taiwan, R.O.C. Phone: 886-2-2657-7898 Fax: 886-2-2657-8751 Email: [email protected] Web Site: www.ic-media.com.tw Important notice: This document contains information of a new product. IC Media Corp reserves the right to make any changes without further notice to any product herein to improve design, function or quality and reliability. No responsibility is assumed by IC Media Corp for its use, nor for any infringements of patents of third parties, which may result from its use. ©2000, 2001,2002 IC Media Corporation & IC Media Technology Corp page 1 7/25/2003 Company Confidential ICM532B CIF Color CMOS Sensor with USB Output Outline Spec, V 1.1 November, 2002 Features • • • • • • • • • • • • • • • • • • CIF format (352x288) pixels, used with 1/7” optical system. QVGA format (320x240) pixels, used with 1/7” optical system QCIF format (176x144) pixels, cropped or subsampled, up to 37.5 fps. Progressive readout Output data format: compressed 8-bit raw data Image processing and decompression supported with proprietary software. Image processing functions include color interpolation, color correction, auto white balance, auto exposure, auto anti-flickering, and sharpening. Proprietary data compression Input/Output interface: USB 1.1 Full Speed Electronic exposure control On-chip 9-bit ADC Correlated double sampling Dead pixel and dead column removal Power down/Suspend mode 8 User Programmable GPIO pins Optional 3.3V Serial EEPROM register loading during power-up (24C02/04/08/16) Automatic optical black compensation Mirror image Single 3.3 V power supply Key Parameters • • • • • • • • • • • • • • • • • • Number of Active Pixels: up to 352x288 Number of Physical Pixels: 362x298 Frame Rate: up to 30 fps ( 35 fps QCIF ) Pixel Size: 6.0 µm x 6.0 µm Sensor Area: 2.2 mm x 1.8 mm Single Crystal Frequency: 6 MHz Exposure Time: 125 µs (@ 25 fps, 1 line) ~ 8 s (@ 12 fps) Sensitivity: 1.0 V/lux-sec (555 nm) Quantum Efficiency: 38 % (555 nm) Dynamic Range: 53 dB (analog), 48 dB (digital) Fill Factor: 36% S/N Ratio: 45 dB @ 75% full signal level Sensitive to infrared illumination source Digital Gain: 1 ~ 64 x @ 2N for all pixels RGB Gain: 1/256 ~ 64 x for individual Bayer pattern pixels Power Supply: 3.3 V Power consumption: 130mW typ. Packages: SPLCC48 ©2000, 2001,2002 IC Media Corporation & IC Media Technology Corp page 2 7/25/2003 Company Confidential ICM532B CIF Color CMOS Sensor with USB Output Outline Spec, V 1.1 November, 2002 General Description ICM-532B is a single-chip, CIF resolution, digital color PC camera with integrated data compression, line buffer and Full Speed USB 1.1 interface. All the image processing functions (color interpolation, color correction, auto white balance, auto exposure, auto anti-flickering, sharpening) are performed by software in the host computer. It incorporates a 352x288 sensor array operating at 6 ~ 30 frames per second in progressive manner. Each pixel is covered by a color filter, which forms a “Bayer pattern.” Correlated double sampling is performed by the internal ADC and timing circuitry. The raw data can be adjusted with digital gain. The raw data is compressed using a proprietary compression scheme. The compression allows video out in 8-bit compressed data format through USB 1.1 with 30 frames per second video capability. For higher frame-rates, sub-sampled or cropped QCIF (176x144) modes are available that support 35 frames per second. 8 Pins are supplied that can be programmed by the driver as general purpose I/O pins, with individually selectable output enables. During power-up, the internal control registers can be loaded from an external serial EEPROM. This allows customization of Vendor ID and Product ID, as well as initialization of other device parameters. The 48 MHz clock required for the ICM-532B is provided by an on-chip phase-lock loop that is driven by an external 6 MHz crystal oscillator. Using a PLL reduces power dissipation, electrical noise and the cost of the crystal. It also reduces the need for EMI shielding that would be required if a 48 MHz oscillator were used. The highest frequency external signal is the 12Mbps on the differential USB data pins. Software Support • • Computer & OS requirements: 750 MHz, 64M memory for 30 fps; 300 MHz, 64M memory for 12 fps. Windows 98, Windows ME, Windows 2000 Macintosh OS 9. Driver support • WDM USB driver • TWAIN • DirectShow • VFW extension driver • Proprietary DirectShow decoder • Installation software Applications • • PC camera Embedded Solutions (Notebooks, LCD monitors) ©2000, 2001,2002 IC Media Corporation & IC Media Technology Corp page 3 7/25/2003 Company Confidential ICM532B CIF Color CMOS Sensor with USB Output Outline Spec, V 1.1 November, 2002 1. Pin Assignments Pin # 36 37 40 39 3,5,34 44 2 1 Name DN DP XIN XOUT Reserved Test Clock_S Data_S Class B,IO B,IO A,I A,O D,O D, I, N D, IO D, IO Function USB D- connection USB D+ connection 6 MHz Crystal Input 6 MHz Crystal Output Leave Unconnected Leave Unconnected Serial clock, for external serial EEPROM Serial data, for external serial EEPROM 16 8 15 RSET RSTN RAMP A,I D,SI,U A,O Resistor to Ground = 75 ΚΩ Chip Reset, active low Analog Test Output 46 47 48 10 11 12 13 14 GPIO 0 GPIO 1 GPIO 2 GPIO 3 GPIO 4 GPIO 5 GPIO 6 GPIO 7 D,IO D,IO D,IO D,IO D,IO D,IO D,IO D,IO User Programmable I/O, Requires External Pull-up User Programmable I/O, Requires External Resistor User Programmable I/O, Requires External Pull-up User Programmable I/O User Programmable I/O User Programmable I/O User Programmable I/O User Programmable I/O 7,27,31 9,28,30 19 17 4,26,33, 38,41,43 6,29,32, 35,42,45 18 VDDA GNDA VDDD GNDD VDDK P P P P P Sensor & PLL Analog Power Sensor & PLL Analog Ground Sensor Digital Power Sensor Digital Ground Digital Power GNDK P Digital Ground GNDS P Substrate Ground Class Code: A – Analog signal, D – Digital signal, I – Input, SI – Schmitt Input, O – Output, IO – Bidirectional, P – Power or ground, U – Internal pull-up, N – Internal pull-down, B – USB Pad 2. Functional Description ICM-532B is a single-chip USB digital color imaging device. It includes a 352x288 sensor array, 352 column–level ADC, and correlated double sampling circuitry. All the programmable parameters are set by writing through the USB interface which can address the register file consisting of 8-bit registers. The internal CIF image sensor is based upon the ICM-102B. The output format is USB 1.1 compatible compressed video data using a single ISOCHRONOUS channel. Dead pixels and dead columns are ©2000, 2001,2002 IC Media Corporation & IC Media Technology Corp page 4 7/25/2003 Company Confidential ICM532B CIF Color CMOS Sensor with USB Output Outline Spec, V 1.1 November, 2002 removed, to generate a high quality image. 5X Proprietary 1/7” lens ICM-102B Compression USB CIF Image Sensor USB Enabled Computer Line Buffer Figure 1. Block Diagram 3. Electrical Characteristics 3.1. DC Characteristics 1. General DC Characteristics Symbol Parameter IDD Operating Current @ VCC=3.3 V, 25 °C Suspend Current @ VCC=3.3 V, 25 °C Input Low Current Input High Current Tri-state Leakage Current Input Capacitance Output Capacitance Bi-directional Buffer IDDS IIL IIH IOZ CIN COUT CBID Minimum Rating Typical 40 Maximum Units mA 500 uA -1 1 µA -1 1 µA -10 10 µA 3 pF 3 pF 3 pF ©2000, 2001,2002 IC Media Corporation & IC Media Technology Corp page 5 7/25/2003 Company Confidential ICM532B CIF Color CMOS Sensor with USB Output Outline Spec, V 1.1 November, 2002 Capacitance USB Output Impedance Input Pull-up/down Resistance RO RL 6 Ω 18 50 KΩ Rating Typical 3.3 Units 2. Electrical DC Characteristics Symbol Parameter VCC Operating Power Supply Output High Voltage USB Output Low Voltage USB Output High Voltage VOH VUL VUH Minimum 3.0 Maximum 3.6 2.4 V V 0.3 2.8 V V 3.2. AC Characteristics Symbol Parameter TRISE/FALL USB Switching Times USB Cross Point VCR Minimum 4 Rating Typical 10 Units 1.3 90% Maximum 20 ns 2.0 V 90% VUH VCR VUL 10% TRISE TFALL 10% Figure 3. DP/DN Timing ©2000, 2001,2002 IC Media Corporation & IC Media Technology Corp page 6 7/25/2003 Company Confidential ICM532B CIF Color CMOS Sensor with USB Output Outline Spec, V 1.1 November, 2002 4. Mechanical Information ICM532B supports SPLCC (Plastic Shrunk LCC48 Packaging) packaging. Note that pin 1 should face up when a lens and the default driver are used. Figure 4. SPLCC48 Packaging 5. Board Design Information Components: • ICM-532B • 6MHz Crystal • RSET resistor • USB connector or cable with 1.5kΩ pull-up on DP. • 3.3v voltage regulator and associated components • Power Supply filter capacitors • Pull-up for SDA, SCL, GPIO0 GPIO1, and GPIO2 • If desired: Reset circuitry. A 0.1uF capacitor on RSTN is sufficient for power-on reset. ©2000, 2001,2002 IC Media Corporation & IC Media Technology Corp page 7 7/25/2003 Company Confidential ICM532B CIF Color CMOS Sensor with USB Output Outline Spec, V 1.1 November, 2002 6. Ordering Information Part number for different package: Description Shrunk Plastic LCC48 package packaged, USB CIF resolution sensor (3.3 V) Part Number ICM-532Bsa Contact Addresses: IC Media Corporation IC Media Technology 545 East Brokaw Road San Jose, CA 95112, U.S.A. Phone: (408) 451-8838 Fax: (408) 451-8839 Email: [email protected] Web Site: www.ic-media.com 6F, No. 61, ChowTze Street., NeiHu District Taipei, Taiwan, R.O.C. Phone: 886-2-2657-7898 Fax: 886-2-2657-8751 Email: [email protected] Web Site: www.ic-media.com ©2000, 2001,2002 IC Media Corporation & IC Media Technology Corp page 8 7/25/2003 Company Confidential