CY7C4421/4201/4211/4221 CY7C4231/4241/4251 64/256/512/1K/2K/4K/8K x 9 Synchronous FIFOs Features Functional Description • High-speed, low-power, First-In, First-Out (FIFO) memories — 64 × 9 (CY7C4421) — 256 × 9 (CY7C4201) — 512 × 9 (CY7C4211) — 1K × 9 (CY7C4221) — 2K × 9 (CY7C4231) — 4K × 9 (CY7C4241) — 8K × 9 (CY7C4251) • High-speed 100-MHz operation (10 ns Read/Write cycle time) • Low power (ICC = 35 mA) • Fully asynchronous and simultaneous Read and Write operation • Empty, Full, and Programmable Almost Empty and Almost Full status flags • TTL-compatible • Expandable in width • Output Enable (OE) pin • Independent Read and Write enable pins • Center power and ground pins for reduced noise • Width-expansion capability • Space saving 7 mm × 7 mm 32-pin TQFP • 32-pin PLCC • Pin-compatible and functionally equivalent to IDT72421, 72201, 72211, 72221, 72231, and 72241 These FIFOs have 9-bit input and output ports that are controlled by separate clock and enable signals. The input port is controlled by a free-running clock (WCLK) and two Write-enable pins (WEN1, WEN2/LD). When WEN1 is LOW and WEN2/LD is HIGH, data is written into the FIFO on the rising edge of the WCLK signal. While WEN1, WEN2/LD is held active, data is continually written into the FIFO on each WCLK cycle. The output port is controlled in a similar manner by a free-running Read clock (RCLK) and two Read-enable pins (REN1, REN2). In addition, the CY7C42X1 has an output enable pin (OE). The Read (RCLK) and Write (WCLK) clocks may be tied together for single-clock operation or the two clocks may be run independently for asynchronous Read/Write applications. Clock frequencies up to 100 MHz are achievable. Depth expansion is possible using one enable input for system control, while the other enable is controlled by expansion logic to direct the flow of data. D0- 8 Pin Configuration D1 D0 PAF PAE GND REN1 RCLK REN2 OE WCLK WEN1 WEN2/LD FLAG PROGRAM REGISTER Write CONTROL Dual Port RAM Array 64 x 9 Read POINTER RESET LOGIC THREE-STATE OUTPUTREGISTER Read CONTROL Cypress Semiconductor Corporation Document #: 38-06016 Rev. *A PAF PAE GND REN1 RCLK REN2 1 2 3 4 5 6 7 8 24 23 22 21 20 19 18 17 WEN1 WCLK WEN2/LD VCC Q8 Q7 Q6 Q5 9 10 11 12 13 14 15 16 OE EF RCLK REN1 REN2 • TQFP Top View 32 31 30 29 28 27 26 25 D1 D0 OE Q0- 8 RS WEN1 WCLK WEN2/LD VCC Q8 Q7 Q6 Q5 3901 North First Street • San Jose • Q3 Q4 8k x 9 Q2 RS EF PAE PAF FF 4 3 2 1 32 3130 29 5 28 6 27 7 26 8 9 25 10 24 11 23 12 22 21 13 14151617181920 D2 D 3 EF D 4 FF Q D5 0 Q1 D6 Q 2 D7 Q 3 D8 Q4 RS FLAG LOGIC Write POINTER PLCC Top View D2 D3 D4 D5 D6 D7 D8 INPUT REGISTER FF Q0 Q1 Logic Block Diagram The CY7C42X1 are high-speed, low-power FIFO memories with clocked Read and Write interfaces. All are 9 bits wide. The CY7C42X1 are pin-compatible to IDT722X1. Programmable features include Almost Full/Almost Empty flags. These FIFOs provide solutions for a wide variety of data buffering needs, including high-speed data acquisition, multiprocessor interfaces, and communications buffering. CA 95134 • 408-943-2600 Revised March 6, 2202 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Selection Guide -10 -15 -25 Unit 100 66.7 40 MHz Maximum Access Time 8 10 15 ns Minimum Cycle Time 10 15 25 ns Minimum Data or Enable Set-up 3 4 6 ns 0.5 1 1 ns 8 10 15 ns Commercial 35 35 35 ICC1 Industrial 40 40 40 Maximum Frequency Minimum Data or Enable Hold Maximum Flag Delay Active Power Supply Current Density CY7C4421 CY7C4201 CY7C4211 CY7C4221 CY7C4231 CY7C4241 CY7C4251 64 × 9 256 × 9 512 × 9 1K × 9 2K × 9 4K × 9 8K × 9 Functional Description The CY7C42X1 provides four status pins: Empty, Full, Almost Empty, Almost Full. The Almost Empty/Almost Full flags are programmable to single word granularity. The programmable flags default to Empty – 7 and Full – 7. The flags are synchronous, i.e., they change state relative to either the Read clock (RCLK) or the Write clock (WCLK). When entering or exiting the Empty and Almost Empty states, the flags are updated exclusively by the RCLK. The flags denoting Almost Full, and Full states are updated exclusively by WCLK. The synchronous flag architecture guarantees that the flags maintain their status for at least one cycle. All configurations are fabricated using advanced 0.65µ N-Well CMOS technology. Input ESD protection is greater than 2001V, and latch-up is prevented by the use of guard rings. Architecture The CY7C42X1 consists of an array of 64 to 8K words of 9 bits each (implemented by a dual-port array of SRAM cells), a Read pointer, a Write pointer, control signals (RCLK, WCLK, REN1, REN2, WEN1, WEN2, RS), and flags (EF, PAE, PAF, FF). Resetting the FIFO Upon power-up, the FIFO must be reset with a Reset (RS) cycle. This causes the FIFO to enter the Empty condition signified by EF being LOW. All data outputs (Q0–8) go LOW tRSF after the rising edge of RS. In order for the FIFO to reset to its default state, a falling edge must occur on RS and the user must not read or Write while RS is LOW. All flags are guaranteed to be valid tRSF after RS is taken LOW. active. REN1 and REN2 must set up tENS before RCLK for it to be a valid Read function. WEN1 and WEN2 must occur tENS before WCLK for it to be a valid Write function. An output enable (OE) pin is provided to three-state the Q0–8 outputs when OE is asserted. When OE is enabled (LOW), data in the output register will be available to the Q0–8 outputs after tOE. The FIFO contains overflow circuitry to disallow additional writes when the FIFO is full, and underflow circuitry to disallow additional reads when the FIFO is empty. An empty FIFO maintains the data of the last valid Read on its Q0–8 outputs even after additional reads occur. Write Enable 1 (WEN1). If the FIFO is configured for programmable flags, Write Enable 1 (WEN1) is the only Write enable control pin. In this configuration, when Write Enable 1 (WEN1) is LOW, data can be loaded into the input register and RAM array on the LOW-to-HIGH transition of every Write clock (WCLK). Data is stored is the RAM array sequentially and independently of any on-going Read operation. Write Enable 2/Load (WEN2/LD). This is a dual-purpose pin. The FIFO is configured at Reset to have programmable flags or to have two Write enables, which allows for depth expansion. If Write Enable 2/Load (WEN2/LD) is set active HIGH at Reset (RS = LOW), this pin operates as a second Write enable pin. If the FIFO is configured to have two Write enables, when Write Enable (WEN1) is LOW and Write Enable 2/Load (WEN2/LD) is HIGH, data can be loaded into the input register and RAM array on the LOW-to-HIGH transition of every Write clock (WCLK). Data is stored in the RAM array sequentially and independently of any on-going Read operation. FIFO Operation Programming When the WEN1 signal is active LOW and WEN2 is active HIGH, data present on the D0–8 pins is written into the FIFO on each rising edge of the WCLK signal. Similarly, when the REN1 and REN2 signals are active LOW, data in the FIFO memory will be presented on the Q0–8 outputs. New data will be presented on each rising edge of RCLK while REN1 and REN2 are When WEN2/LD is held LOW during Reset, this pin is the load (LD) enable for flag offset programming. In this configuration, WEN2/LD can be used to access the four 8-bit offset registers contained in the CY7C42X1 for writing or reading data to these registers. Document #: 38-06016 Rev. *A Page 2 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 When the device is configured for programmable flags and both WEN2/LD and WEN1 are LOW, the first LOW-to-HIGH transition of WCLK writes data from the data inputs to the empty offset least significant bit (LSB) register. The second, third, and fourth LOW-to-HIGH transitions of WCLK store data in the empty offset most significant bit (MSB) register, full offset LSB register, and full offset MSB register, respectively, when WEN2/LD and WEN1 are LOW. The fifth LOW-to-HIGH transition of WCLK while WEN2/LD and WEN1 are LOW writes data to the empty LSB register again. Figure 1 shows the registers sizes and default values for the various device types. 64 × 9 8 It is not necessary to write to all the offset registers at one time. A subset of the offset registers can be written; then by bringing the WEN2/LD input HIGH, the FIFO is returned to normal Read and Write operation. The next time WEN2/LD is brought LOW, a Write operation stores data in the next offset register in sequence. The contents of the offset registers can be read to the data outputs when WEN2/LD is LOW and both REN1 and REN2 are LOW. LOW-to-HIGH transitions of RCLK Read register contents to the data outputs. Writes and reads should not be preformed simultaneously on the offset registers. 256 × 9 0 6 5 8 Empty Offset (LSB) Reg. Default Value = 007h 8 Empty Offset (LSB) Reg. Default Value = 007h 0 8 512 × 9 0 7 8 Empty Offset (LSB) Reg. Default Value = 007h 0 1 0 7 8 Empty Offset (LSB) Reg. Default Value = 007h 0 8 1K × 9 0 7 8 (MSB) 0 8 0 6 5 8 Full Offset (LSB) Reg Default Value = 007h 0 7 8 Full Offset (LSB) Reg Default Value = 007h 0 8 8 Full Offset (LSB) Reg Default Value = 007h 0 8 (MSB) 00 0 7 0 7 Full Offset (LSB) Reg Default Value = 007h 0 1 8 8 0 7 8 0 7 8 Full Offset (LSB) Reg Default Value = 007h 8 (MSB) 000 (MSB) 00000 0 7 8 8 0 7 Full Offset (LSB) Reg Default Value = 007h 0 3 0 4 8 Full Offset (LSB) Reg Default Value = 007h 0 2 0 7 (MSB) 0000 0 7 8 Empty Offset (LSB) Reg. Default Value = 007h 0 3 8 (MSB) 000 8 8K × 9 Empty Offset (LSB) Reg. Default Value = 007h 0 2 8 (MSB) 00 4K × 9 Empty Offset (LSB) Reg. Default Value = 007h 0 1 8 (MSB) 0 2K × 9 0 1 8 (MSB) 0000 0 4 (MSB) 00000 Figure 1. Offset Register Location and Default Values Document #: 38-06016 Rev. *A Page 3 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Programmable Flag (PAE, PAF) Operation (256 – m), CY7C4211 (512 – m), CY7C4221 (1K – m), CY7C4231 (2K – m), CY7C4241 (4K – m), and CY7C4251 (8K – m). PAF is set HIGH by the LOW-to-HIGH transition of WCLK when the number of available memory locations is greater than m. Whether the flag offset registers are programmed as described in Table 1 or the default values are used, the programmable almost-empty flag (PAE) and programmable almost-full flag (PAF) states are determined by their corresponding offset registers and the difference between the Read and Write pointers. Table 1. Writing the Offset Registers The number formed by the empty offset least significant bit register and empty offset most significant register is referred to as n and determines the operation of PAE. PAE is synchronized to the LOW-to-HIGH transition of RCLK by one flip-flop and is LOW when the FIFO contains n or fewer unread words. PAE is set HIGH by the LOW-to-HIGH transition of RCLK when the FIFO contains (n + 1) or greater unread words. WCLK[1] LD WEN 0 0 Empty Offset (LSB) Empty Offset (MSB) Full Offset (LSB) Full Offset (MSB) 0 1 No Operation 1 0 Write Into FIFO 1 1 No Operation The number formed by the full offset least significant bit register and full offset most significant bit register is referred to as m and determines the operation of PAF. PAE is synchronized to the LOW-to-HIGH transition of WCLK by one flip-flop and is set LOW when the number of unread words in the FIFO is greater than or equal to CY7C4421. (64 – m), CY7C4201 Selection Table 2. Status Flags Number of Words in FIFO CY7C4421 CY7C4201 0 1 to n CY7C4211 0 [2] FF PAF PAE EF H H L L [2] 0 1 to n [2] H H L H (n + 1) to 32 (n + 1) to 128 1 to n (n + 1) to 256 H H H H 33 to (64 – (m + 1)) 129 to (256 – (m + 1)) 257 to (512 – (m + 1)) H H H H (64 – m)[3] to 63 (256 – m)[3] to 255 (512 – m)[3] to 511 H L H H 64 256 512 L L H H Number of Words in FIFO CY7C4221 0 1 to n CY7C4231 0 [2] 1 to n (n + 1) to 512 CY7C4241 0 [2] 0 [2] (n + 1) to 1024 CY7C4251 [2] 1 to n 1 to n (n + 1) to 2048 (n + 1) to 4096 513 to (1024 – (m + 1)) 1025 to (2048 – (m + 1)) 2049 to (4096 – (m + 1)) 4097 to (8192 – (m + 1)) (1024 – m) 1024 [3] to 1023 (2048 – m) 2048 [3] to 2047 (4096 – m) 4096 [3] to 4095 (8192 – m) 8192 [3] to 8191 FF PAF PAE EF H H L L H H L H H H H H H H H H H L H H L L H H Notes: 1. The same selection sequence applies to reading from the registers. REN1 and REN2 are enabled and a Read is performed on the LOW-to-HIGH transition of RCLK. 2. n = Empty Offset (n = 7 default value). 3. m = Full Offset (m = 7 default value). Document #: 38-06016 Rev. *A Page 4 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Width Expansion Configuration Flag Operation Word width may be increased simply by connecting the corresponding input controls signals of multiple devices. A composite flag should be created for each of the end-point status flags (EF and FF). The partial status flags (PAE and PAF) can be detected from any one device. Figure 2 demonstrates a 18-bit word width by using two CY7C42X1s. Any word width can be attained by adding additional CY7C42X1s. The CY7C42X1 devices provide four flag pins to indicate the condition of the FIFO contents. Empty, Full, PAE, and PAF are synchronous. Full Flag The Full Flag (FF) will go LOW when device is full. Write operations are inhibited whenever FF is LOW regardless of the state of WEN1 and WEN2/LD. FF is synchronized to WCLK, i.e., it is exclusively updated by each rising edge of WCLK. When the CY7C42X1 is in a Width Expansion Configuration, the Read Enable (REN2) control input can be grounded (See Figure 2). In this configuration, the Write Enable 2/Load (WEN2/LD) pin is set to LOW at Reset so that the pin operates as a control to load and read the programmable flag offsets. Empty Flag The Empty Flag (EF) will go LOW when the device is empty. Read operations are inhibited whenever EF is LOW, regardless of the state of REN1 and REN2. EF is synchronized to RCLK, i.e., it is exclusively updated by each rising edge of RCLK. RESET (RS) DATA IN (D) 18 Write Write Write RESET (RS) 9 9 Read CLOCK (RCLK) CLOCK (WCLK) Read ENABLE 1 (REN1) ENABLE 1 (WEN1) OUTPUT ENABLE (OE) ENABLE 2/LOAD (WEN2/LD) CY7C42X1 PROGRAMMABLE (PAF) CY7C42X1 EF EMPTY FLAG (EF) #2 EF FULL FLAG (FF) # 1 PROGRAMMABLE (PAE) EMPTY FLAG (EF) #1 FF FF 9 FULL FLAG (FF) # 2 DATA OUT (Q) 18 9 Read Enable 2 (REN2) Read Enable 2 (REN2) 42X1–16 Figure 2. Block Diagram of 64 x 9, 256 x 9, 512 x 9, 1024 x 9, 2048 x 9, 4096 x 9, 8192 x 9 Synchronous FIFO Memory Used in a Width Expansion Configuration Document #: 38-06016 Rev. *A Page 5 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Output Current into Outputs (LOW)............................. 20 mA Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ...................................–65°C to +150°C Ambient Temperature with Power Applied...............................................–55°C to +125°C Static Discharge Voltage .......................................... > 2001V (per MIL-STD-883, Method 3015) Latch-up Current..................................................... > 200 mA Operating Range Supply Voltage to Ground Potential ............... –0.5V to +7.0V Range Ambient Temperature VCC DC Voltage Applied to Outputs in High-Z State ............................................... –0.5V to +7.0V Commercial 0°C to +70°C 5V ±10% –40°C to +85°C 5V ±10% DC Input Voltage............................................ –3.0V to +7.0V Industrial [4] Pin Definitions Pin Name I/O Description D0–8 Data Inputs I Data Inputs for 9-bit Bus Q0–8 Data Outputs O Data Outputs for 9-bit Bus WEN1 Write Enable 1 I The only Write enable to have programmable flags when device is configured. Data is written on a LOW-to-HIGH transition of WCLK when WEN1 is asserted and FF is HIGH. If the FIFO is configured to have two Write enables, data is written on a LOW-to-HIGH transition of WCLK when WEN1 is LOW and WEN2/LD and FF are HIGH. WEN2/LD Dual Write Enable 2 Mode Pin Load I If HIGH at reset, this pin operates as a second Write enable. If LOW at reset, this pin operates as a control to Write or Read the programmable flag offsets. WEN1 must be LOW and WEN2 must be HIGH to write data into the FIFO. Data will not be written into the FIFO if the FF is LOW. If the FIFO is configured to have programmable flags, WEN2/LD is held LOW to write or read the programmable flag offsets. REN1, REN2 Read Enable Inputs I Enables Device for Read Operation WCLK Write Clock I The rising edge clocks data into the FIFO when WEN1 is LOW, WEN2/LD is HIGH, and the FIFO is not Full. When LD is asserted, WCLK writes data into the programmable flag-offset register. RCLK Read Clock I The rising edge clocks data out of the FIFO when REN1 and REN2 are LOW and the FIFO is not Empty. When WEN2/LD is LOW, RCLK reads data out of the programmable flag-offset register. EF Empty Flag O When EF is LOW, the FIFO is empty. EF is synchronized to RCLK. FF Full Flag O When FF is LOW, the FIFO is full. FF is synchronized to WCLK. PAE Programmable Almost Empty O When PAE is LOW, the FIFO is almost empty based on the almost empty offset value programmed into the FIFO. PAF Programmable Almost Full O When PAF is LOW, the FIFO is almost full based on the almost full offset value programmed into the FIFO. RS Reset I Resets device to empty condition. A reset is required before an initial Read or Write operation after power-up. OE Output Enable I When OE is LOW, the FIFO’s data outputs drive the bus to which they are connected. If OE is HIGH, the FIFO’s outputs are in High-Z (high-impedance) state. I Note: 4. TA is the “instant on” case temperature. Document #: 38-06016 Rev. *A Page 6 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Electrical Characteristics Over the Operating Range[5] -10 Parameter Description Test Conditions Min. -15 Max. VOH Output HIGH Voltage VCC = Min., IOH = –2.0 mA VOL Output LOW Voltage VCC = Min., IOL = 8.0 mA VIH Input HIGH Voltage VIL Input LOW Voltage IIX Input Leakage Current VCC = Max. IOS[6] Output Short Circuit Current VCC = Max., VOUT = GND –90 IOZL IOZH Output OFF, High-Z Current OE > VIH, VSS < VO < VCC –10 ICC1[7] Active Power Supply Current Commercial 35 Industrial ICC2[8] Average Standby Current Commercial Industrial Min. 2.4 -25 Max. 2.4 Max. V 0.4 VCC 2.2 –3.0 0.8 –10 +10 Unit 2.4 0.4 2.2 Min. 0.4 V VCC V VCC 2.2 –3.0 0.8 –3.0 0.8 V –10 +10 –10 +10 µA –90 +10 –90 –10 +10 mA –10 +10 mA 35 35 mA 40 40 40 mA 10 10 10 mA 15 15 15 mA Capacitance[9] Parameter Description Input Capacitance Output Capacitance CIN COUT Test Conditions TA = 25°C, f = 1 MHz, VCC = 5.0V Max. 5 7 Unit pF pF AC Test Loads and Waveforms[10, 11] R1 1.1 KΩ ALL INPUT PULSES 5V OUTPUT 3.0V R2 680Ω CL INCLUDING JIG AND SCOPE Equivalent to: GND ≤ 3 ns THÉVENIN EQUIVALENT 420Ω OUTPUT 90% 10% 90% 10% ≤ 3 ns 1.91V Switching Characteristics Over the Operating Range -10 Parameter Description Min. -15 Max. Min. 100 -25 Max. Min. Unit 40 MHz 15 ns tS Clock Cycle Frequency tA Data Access Time tCLK Clock Cycle Time 10 15 25 ns tCLKH Clock HIGH Time 4.5 6 10 ns tCLKL Clock LOW Time 4.5 6 10 ns tDS Data Set-up Time 3 4 6 ns 2 8 66.7 Max. 2 10 2 Notes: 5. See the last page of this specification for Group A subgroup testing information. 6. Test no more than one output at a time for not more than one second. 7. Outputs open. Tested at Frequency = 20 MHz. 8. All inputs = VCC – 0.2V, except WCLK and RCLK, which are switching at 20 MHz. 9. Tested initially and after any design or process changes that may affect these parameters. 10. CL = 30 pF for all AC parameters except for tOHZ. 11. CL = 5 pF for tOHZ. Document #: 38-06016 Rev. *A Page 7 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Switching Characteristics Over the Operating Range -10 Parameter Description Min. -15 Max. Min. -25 Max. Min. Max. Unit tDH Data Hold Time tENS Enable Set-up Time 0.5 1 1 ns 3 4 6 ns tENH Enable Hold Time 0.5 tRS Reset Pulse Width[12] 10 1 1 ns 15 25 ns tRSS Reset Set-up Time 8 tRSR Reset Recovery Time 8 10 15 ns 10 15 ns tRSF Reset to Flag and Output Time tOLZ Output Enable to Output in Low-Z[13] 0 tOE Output Enable to Output Valid 3 7 3 8 3 12 ns tOHZ Output Enable to Output in High-Z[13] 3 7 3 8 3 12 ns tWFF Write Clock to Full Flag 8 10 15 ns tREF Read Clock to Empty Flag 8 10 15 ns tPAF Clock to Programmable Almost-Full Flag 8 10 15 ns tPAE Clock to Programmable Almost-Full Flag 8 10 15 ns tSKEW1 Skew Time between Read Clock and Write Clock for Empty Flag and Full Flag 5 6 10 ns tSKEW2 Skew Time between Read Clock and Write Clock for Almost-Empty Flag and Almost-Full Flag 10 15 18 ns 10 15 0 25 0 ns ns Switching Waveforms Write Cycle Timing tCLK tCLKH tCLKL WCLK tDS tDH D0 –D8 tENS tENH WEN1 NO OPERATION NO OPERATION WEN2 (if applicable) tWFF tWFF FF tSKEW1 [14] RCLK REN1,REN2 Notes: 12. Pulse widths less than minimum values are not allowed. 13. Values guaranteed by design, not currently tested. Document #: 38-06016 Rev. *A Page 8 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Switching Waveforms (continued) Read Cycle Timing tCKL tCLKH tCLKL RCLK tENS tENH REN1,REN2 NO OPERATION tREF tREF EF tA Q0 –Q8 VALID DATA tOLZ tOHZ tOE OE tSKEW1 [15] WCLK WEN1 WEN2 Reset Timing[16] tRS RS tRSS tRSR tRSS tRSR tRSS tRSR REN1, REN2 WEN1 WEN2/LD [17] tRSF EF,PAE tRSF FF,PAF, tRSF OE=1 [18] Q0 - Q8 OE=0 Notes: 14. tSKEW1 is the minimum time between a rising RCLK edge and a rising WCLK edge to guarantee that FF will go HIGH during the current clock cycle. If the time between the rising edge of RCLK and the rising edge of WCLK is less than tSKEW1, then FF may not change state until the next WCLK rising edge. 15. tSKEW1 is the minimum time between a rising WCLK edge and a rising RCLK edge to guarantee that EF will go HIGH during the current clock cycle. It the time between the rising edge of WCLK and the rising edge of RCLK is less than tSKEW1, then EF may not change state until the next RCLK rising edge. Document #: 38-06016 Rev. *A Page 9 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Switching Waveforms (continued) First Data Word Latency after Reset with Simultaneous Read and Write WCLK t DS D0–D8 D0 (FIRSTVALID Write) D1 tENS D2 D3 [20] tA D4 [19] tFRL WEN1 WEN2 (if applicable) tSKEW1 RCLK tREF EF tA REN1, REN2 Q0 –Q8 D0 D1 tOLZ tOE OE Empty Flag Timing WCLK tDS tDS DATAWRITE2 DATAWRITE1 D0 –D8 tENH tENS tENH tENS WEN1 WEN2 (if applicable) tENS tENH tFRL tENS [19] tENH tFRL [19] RCLK tSKEW1 tREF tREF tREF tSKEW1 EF REN1, REN2 LOW OE tA Q0 –Q8 DATA IN OUTPUT REGISTER DATA Read Notes: 16. The clocks (RCLK, WCLK) can be free-running during reset. 17. Holding WEN2/LD HIGH during reset will make the pin act as a second enable pin. Holding WEN2/LD LOW during reset will make the pin act as a load enable for the programmable flag offset registers. 18. After reset, the outputs will be LOW if OE = 0 and three-state if OE=1. 19. When tSKEW1 > minimum specification, tFRL (maximum) = tCLK + tSKEW1. When tSKEW1 < minimum specification, tFRL (maximum) = either 2*tCLK + tSKEW1 or tCLK + tSKEW1. The Latency Timing applies only at the Empty Boundary (EF = LOW). 20. The first word is available the cycle after EF goes HIGH, always. Document #: 38-06016 Rev. *A Page 10 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Switching Waveforms (continued) Full Flag Timing NO Write NO Write NO Write WCLK tSKEW1 [14] tSKEW1 [14] tDS DATA Write DATA Write D0 –D8 tWFF tWFF tWFF FF WEN1 WEN2 (if applicable) RCLK tENH OE tENH tENS REN1, REN2 tENS LOW tA Q0 –Q8 tA DATA Read DATA IN OUTPUT REGISTER NEXT DATA Read Programmable Almost Empty Flag Timing tCLKL tCLKH WCLK tENS tENH WEN1 WEN2 (if applicable) tENS tENH PAE tSKEW2 [21] Note 22 N + 1 WORDS INFIFO tPAE Note 23 tPAE RCLK tENS tENS tENH REN1, REN2 Document #: 38-06016 Rev. *A Page 11 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Switching Waveforms (continued) Programmable Almost Full Flag Timing Note 24 tCLKL tCLKH WCLK tENS tENH WEN1 Note 25 WEN2 (if applicable) tPAF tENS tENH PAF FULL − M WORDS IN FIFO [26] FULL − M+1 WORDS IN FIFO tSKEW2 [27] tPAF RCLK tENS tENS tENH REN1, REN2 Write Programmable Registers tCLK tCLKL tCLKH WCLK tENS tENH WEN2/LD tENS WEN1 tDS tDH D0 –D8 PAE OFFSET LSB PAE OFFSET MSB PAF OFFSET LSB PAF OFFSET MSB Notes: 21. tSKEW2 is the minimum time between a rising WCLK and a rising RCLK edge for PAE to change state during that clock cycle. If the time between the edge of WCLK and the rising RCLK is less than tSKEW2, then PAE may not change state until the next RCLK. 22. PAE offset = n. 23. If a Read is performed on this rising edge of the Read clock, there will be Empty + (n – 1) words in the FIFO when PAE goes LOW. 24. If a Write is performed on this rising edge of the Write clock, there will be Full – (m – 1) words of the FIFO when PAF goes LOW. 25. PAF offset = m. 26. 64-m words for CY7C4421, 256 – m words in FIFO for CY7C4201, 512 – m words for CY7C4211, 1024 – m words for CY7C4221, 2048 – m words for CY7C4231, 4096 – m words for CY7C4241, 8192 – m words for CY7C4251. 27. tSKEW2 is the minimum time between a rising RCLK edge and a rising WCLK edge for PAF to change during that clock cycle. If the time between the rising edge of RCLK and the rising edge of WCLK is less than tSKEW2, then PAF may not change state until the next WCLK. Document #: 38-06016 Rev. *A Page 12 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Switching Waveforms (continued) Read Programmable Registers tCLK tCLKL tCLKH RCLK tENS tENH WEN2/LD tENS PAF OFFSET MSB REN1, REN2 tA Q0 –Q8 Document #: 38-06016 Rev. *A UNKNOWN PAE OFFSET LSB PAE OFFSET MSB PAF OFFSET LSB Page 13 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Typical AC and DC Characteristics NORMALIZED SUPPLY CURRENT vs. SUPPLY VOLTAGE NORMALIZED SUPPLY CURRENT vs. AMBIENT TEMPERATURE 1.20 1.2 1.0 VIN = 3.0V TA = 25°C f = 100 MHz 0.8 0.6 4 4.5 5.5 5 1.10 1.00 0.90 25 NORMALIZED tA vs. SUPPLY VOLTAGE 0 1.0 0.9 5.5 35 25 0 1 2 3 OUTPUT VOLTAGE (V) Document #: 38-06016 Rev. *A 4 OUTPUT SINK CURRENT (mA) 45 100 TYPICAL t A CHANGE vs. OUTPUT LOADING 40 1.00 0.75 25 10 VCC = 5.0V TA = 25°C 25 125 AMBIENT TEMPERATURE (°C) 55 75 1.25 SUPPLY VOLTAGE (V) OUTPUT SOURCE CURRENT vs. OUTPUT VOLTAGE 50 VCC = 5.0V 0.50 −55 6 25 FREQUENCY (MHz) Delta t A (ns) NORMALIZED tA NORMALIZED t A 1.1 0.8 OUTPUT SOURCE CURRENT (mA) 0.60 125 1.50 5 0.80 NORMALIZED tA vs. AMBIENT TEMPERATURE 1.2 4.5 0.90 AMBIENT TEMPERATURE (°C) SUPPLY VOLTAGE (V) 4 VCC = 5.0V TA = 25°C VIN = 3.0V 1.00 0.70 0.80 −55 6 1.10 VIN = 3.0V VCC = 5.0V f = 100 MHz NORMALIZED I CC NORMALIZED I CC NORMALIZED I CC 1.4 NORMALIZED SUPPLY CURRENT vs. FREQUENCY 0 0 200 400 600 800 1000 CAPACITANCE (pF) OUTPUT SINK CURRENT vs. OUTPUT VOLTAGE 160 140 120 100 80 60 40 20 0 0 1 2 3 4 OUTPUT VOLTAGE (V) Page 14 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Ordering Information 64 x 9 Synchronous FIFO Speed (ns) 10 15 Ordering Code CY7C4421-10AC Package Name Package Type A32 32-lead Thin Quad Flatpack CY7C4421-10JC J65 32-lead Plastic Leaded Chip Carrier CY7C4421-15AC A32 32-lead Thin Quad Flatpack CY7C4421-15JC J65 32-lead Plastic Leaded Chip Carrier Operating Range Commercial Commercial 256 x 9 Synchronous FIFO Speed (ns) 10 15 25 Ordering Code Package Name Package Type CY7C4201-10AC A32 32-lead Thin Quad Flatpack CY7C4201-10JC J65 32-lead Plastic Leaded Chip Carrier CY7C4201-15AC A32 32-lead Thin Quad Flatpack CY7C4201-15JC J65 32-lead Plastic Leaded Chip Carrier CY7C4201-25AC A32 32-lead Thin Quad Flatpack CY7C4201-25JC J65 32-lead Plastic Leaded Chip Carrier CY7C4201-25AI A32 32-lead Thin Quad Flatpack Operating Range Commercial Commercial Commercial Industrial 512 x 9 Synchronous FIFO Speed (ns) 10 15 25 Ordering Code CY7C4211-10AC Package Name Package Type Operating Range A32 32-lead Thin Quad Flatpack Commercial CY7C4211-10JC J65 32-lead Plastic Leaded Chip Carrier CY7C4211-10AI A32 32-lead Thin Quad Flatpack CY7C4211-10JI J65 32-lead Plastic Leaded Chip Carrier CY7C4211-15AC A32 32-lead Thin Quad Flatpack CY7C4211-15JC J65 32-lead Plastic Leaded Chip Carrier CY7C4211-15AI A32 32-lead Thin Quad Flatpack Industrial CY7C4211-25AC A32 32-lead Thin Quad Flatpack Commercial CY7C4211-25JC J65 32-lead Plastic Leaded Chip Carrier Industrial Commercial 1K x 9 Synchronous FIFO Speed (ns) 10 15 25 Ordering Code CY7C4221-10AC Package Name Package Type A32 32-lead Thin Quad Flatpack CY7C4221-10JC J65 32-lead Plastic Leaded Chip Carrier CY7C4221-15AC A32 32-lead Thin Quad Flatpack CY7C4221-15JC J65 32-lead Plastic Leaded Chip Carrier CY7C4221-25AC A32 32-lead Thin Quad Flatpack CY7C4221-25JC J65 32-lead Plastic Leaded Chip Carrier Operating Range Commercial Commercial Commercial 2K x 9 Synchronous FIFO Speed (ns) 10 15 Ordering Code CY7C4231-10AC Package Name Package Type A32 32-lead Thin Quad Flatpack CY7C4231-10JC J65 32-lead Plastic Leaded Chip Carrier CY7C4231-15AC A32 32-lead Thin Quad Flatpack Document #: 38-06016 Rev. *A Operating Range Commercial Commercial Page 15 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 2K x 9 Synchronous FIFO (continued) Speed (ns) 25 Ordering Code Package Name Package Type CY7C4231-15JC J65 32-lead Plastic Leaded Chip Carrier CY7C4231-25AC A32 32-lead Thin Quad Flatpack CY7C4231-25JC J65 32-lead Plastic Leaded Chip Carrier Operating Range Commercial 4K x 9 Synchronous FIFO Speed (ns) 10 15 25 Ordering Code Package Name Package Type Operating Range CY7C4241-10AC A32 32-lead Thin Quad Flatpack CY7C4241-10JC J65 32-lead Plastic Leaded Chip Carrier Commercial CY7C4241-10JI J65 32-lead Plastic Leaded Chip Carrier Industrial CY7C4241-15AC A32 32-lead Thin Quad Flatpack Commercial CY7C4241-15JC J65 32-lead Plastic Leaded Chip Carrier CY7C4241-25AC A32 32-lead Thin Quad Flatpack CY7C4241-25JC J65 32-lead Plastic Leaded Chip Carrier CY7C4241-25JI J65 32-lead Plastic Leaded Chip Carrier Commercial Industrial 8K x 9 Synchronous FIFO Speed (ns) 10 15 25 Ordering Code CY7C4251-10AC Package Name Package Type Operating Range A32 32-lead Thin Quad Flatpack CY7C4251-10JC J65 32-lead Plastic Leaded Chip Carrier CY7C4251-10AI A32 32-lead Thin Quad Flatpack Industrial CY7C4251-15AC A32 32-lead Thin Quad Flatpack Commercial CY7C4251-15JC J65 32-lead Plastic Leaded Chip Carrier CY7C4251-25AC A32 32-lead Thin Quad Flatpack CY7C4251-25JC J65 32-lead Plastic Leaded Chip Carrier CY7C4251-25AI A32 32-lead Thin Quad Flatpack Document #: 38-06016 Rev. *A Commercial Commercial Industrial Page 16 of 18 CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Package Diagrams 32-lead Thin Plastic Quad Flatpack 7 × 7 × 1.0 mm A32 51-85063-B 32-Lead Plastic Leaded Chip Carrier J65 51-85002-B All product and company names mentioned in this document may be the trademarks of their respective holders. Document #: 38-06016 Rev. *A Page 17 of 18 © Cypress Semiconductor Corporation, 2002. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY7C4421/4201/4211/4221 CY7C4231/4241/4251 Document Title: CY7C4421/4201/4211/4221, CY7C4231/4241/4251 64/256/512/1K/2K/4K/8K x 9 Synchronous FIFOs Document Number: 38-06016 REV. ECN NO. Issue Date Orig. of Change ** 106477 09/10/01 SZV Change from Spec number: 38-00419 to 38-06016 *A 110725 03/20/02 FSG Change Input Leakage current IIX unit from mA to µA (typo) Document #: 38-06016 Rev. *A Description of Change Page 18 of 18