CYPRESS CY7C4291V-25JC

CY7C4281V/CY7C4291V CY7C4261V/CY7C4271V16K/32K/64K/128K x 9 Low-Voltage Deep Sync™ FIFOs
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
16K/32K/64K/128K x 9 Low-Voltage Deep Sync™ FIFOs
Features
• Pin-compatible density upgrade to CY7C42X1V family
• 3.3V operation for low power consumption and easy
integration into low-voltage systems
• High-speed, low-power, first-in first-out (FIFO)
memories
Functional Description
The CY7C4261/71/81/91V are high-speed, low-power FIFO
memories with clocked read and write interfaces. All are nine
bits wide. The CY7C4261/71/81/91V are pin-compatible to the
CY7C42x1V Synchronous FIFO family. Programmable
features include Almost Full/Almost Empty flags. These FIFOs
provide solutions for a wide variety of data buffering needs,
including high-speed data acquisition, multiprocessor interfaces, and communications buffering.
• 16K × 9 (CY7C4261V)
• 32K × 9 (CY7C4271V)
• 64K × 9 (CY7C4281V)
• 128K × 9 (CY7C4291V)
• 0.35-micron CMOS for optimum speed/power
• High-speed 100-MHz operation (10-ns read/write cycle
times)
• Low power
— ICC = 25 mA
— ISB = 4 mA
• Fully asynchronous and simultaneous read and write
operation
• Empty, Full, and programmable Almost Empty and
Almost Full status flags
• Output Enable (OE) pin
• Independent read and write enable pins
• Supports free-running 50% duty cycle clock inputs
• Width- Expansion capability
• Pin-compatible 3.3V solutions for CY7C4261/71/81/91
These FIFOs have 9-bit input and output ports that are
controlled by separate clock and enable signals. The input port
is controlled by a free-running clock (WCLK) and two
write-enable pins (WEN1, WEN2/LD).
When WEN1 is LOW and WEN2/LD is HIGH, data is written
into the FIFO on the rising edge of the WCLK signal. While
WEN1 and WEN2/LD are held active, data is continually
written into the FIFO on each WCLK cycle. The output port is
controlled in a similar manner by a free-running read clock
(RCLK) and two read enable pins (REN1, REN2). In addition,
the CY7C4261/71/81/91V has an output enable pin (OE). The
read (RCLK) and write (WCLK) clocks may be tied together for
single-clock operation or the two clocks may be run independently for asynchronous read/write applications. Clock
frequencies up to 100 MHz are achievable. Depth expansion
is possible using one enable input for system control, while the
other enable is controlled by expansion logic to direct the flow
of data.
D0–8
Pin Configuration
D2
D1
D0
PAF
PAE
GND
FLAG
PROGRAM
REGISTER
WRITE
CONTROL
RS
4 3 2 1 32 31 30
29
28
CY7C4261V
CY7C4271V
CY7C4281V
CY7C4291V
READ
POINTER
27
26
25
24
23
22
21
14 15 16 17 18 19 20
EF
FF
Q0
Q1
Q2
WRITE
POINTER
FLAG
LOGIC
Dual Port
RAM Array
16K/32K
64K/128K
x9
REN1
RCLK
REN2
OE
EF
PAE
PAF
FF
5
6
7
8
9
10
11
12
13
RS
WEN1
WCLK
WEN2/LD
VCC
Q8
Q7
Q6
Q5
Q3
Q4
WCLK WEN1 WEN2/LD
D4
D5
D6
D7
D8
PLCC
Top View
INPUT
REGISTER
D3
LogicBlock Diagram
• Pb-Free Packages Available
RESET
LOGIC
THREE-STATE
OUTPUT REGISTER
READ
CONTROL
OE
Q0–8
Cypress Semiconductor Corporation
Document #: 38-06013 Rev. *B
RCLK REN1 REN2
•
3901 North First Street
•
San Jose, CA 95134
•
408-943-2600
Revised August 2, 2005
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Selection Guide
7C4261/71/81/91V-10
7C4261/71/81/91V-15
7C4261/71/81/91V-25
Unit
100
66.7
40
MHz
8
10
15
ns
Minimum Cycle Time
10
15
25
ns
Minimum Data or Enable Set-up
3.5
4
6
ns
Maximum Frequency
Maximum Access Time
Minimum Data or Enable Hold
0
0
1
ns
Maximum Flag Delay
8
10
15
ns
25
25
mA
Active Power Supply
Current (ICC1)
Commercial
25
Industrial
30
CY7C4261V
CY7C4271V
CY7C4281V
CY7C4291V
Density
16K x 9
32K x 9
64K x 9
128K x 9
Package
32-pin PLCC
32-pin PLCC
32-pin PLCC
32-pin PLCC
Pin Definitions
Signal Name
Description
I/O
Description
D0−8
Data Inputs
I
Data Inputs for 9-bit bus.
Q0−8
Data Outputs
O
Data Outputs for 9-bit bus.
WEN1
Write Enable 1
I
The only write enable when device is configured to have programmable flags.
Data is written on a LOW-to-HIGH transition of WCLK when WEN1 is asserted and FF
is HIGH. If the FIFO is configured to have two write enables, data is written on a
LOW-to-HIGH transition of WCLK when WEN1 is LOW and WEN2/LD and FF are HIGH.
WEN2/LD
Write Enable 2
Dual Mode Pin
Load
I
If HIGH at reset, this pin operates as a second write enable. If LOW at reset, this
pin operates as a control to write or read the programmable flag offsets. WEN1 must be
LOW and WEN2 must be HIGH to write data into the FIFO. Data will not be written into
the FIFO if the FF is LOW. If the FIFO is configured to have programmable flags,
WEN2/LD is held LOW to write or read the programmable flag offsets.
REN1, REN2
Read Enable
Inputs
I
Enables the device for Read operation. Both REN1 and REN2 must be asserted to
allow a read operation.
WCLK
Write Clock
I
The rising edge clocks data into the FIFO when WEN1 is LOW and WEN2/LD is
HIGH and the FIFO is not Full. When LD is asserted, WCLK writes data into the
programmable flag-offset register.
RCLK
Read Clock
I
The rising edge clocks data out of the FIFO when REN1 and REN2 are LOW and
the FIFO are not Empty. When WEN2/LD is LOW, RCLK reads data out of the programmable flag-offset register.
EF
Empty Flag
O
When EF is LOW, the FIFO is empty. EF is synchronized to RCLK.
FF
Full Flag
O
When FF is LOW, the FIFO is full. FF is synchronized to WCLK.
PAE
Programmable
Almost Empty
O
When PAE is LOW, the FIFO is almost empty based on the almost empty offset
value programmed into the FIFO. PAE is synchronized to RCLK.
PAF
Programmable
Almost Full
O
When PAF is LOW, the FIFO is almost full based on the almost full offset value
programmed into the FIFO. PAF is synchronized to WCLK.
RS
Reset
I
Resets device to empty condition. A reset is required before an initial read or write
operation after power-up.
OE
Output Enable
I
When OE is LOW, the FIFO’s data outputs drive the bus to which they are
connected. If OE is HIGH, the FIFO’s outputs are in High Z (high-impedance) state.
Document #: 38-06013 Rev. *B
Page 2 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Functional Description (continued)
The CY7C4261/71/81/91V provides four status pins: Empty,
Full, Programmable Almost Empty, and Programmable
Almost Full. The Almost Empty/Almost Full flags are programmable to single word granularity. The programmable flags
default to Empty + 7 and Full – 7.
The flags are synchronous, i.e., they change state relative to
either the read clock (RCLK) or the write clock (WCLK). When
entering or exiting the Empty and Almost Empty states, the
flags are updated exclusively by the RCLK. The flags denoting
Almost Full, and Full states are updated exclusively by WCLK.
The synchronous flag architecture guarantees that the flags
maintain their status for at least one cycle
All configurations are fabricated using an advanced 0.35µ
CMOS technology. Input ESD protection is greater than
2001V, and latch-up is prevented by the use of guard rings.
Architecture
The CY7C4261/71/81/91V consists of an array of 16K, 32K,
64K, or 128K words of nine bits each (implemented by a
dual-port array of SRAM cells), a read pointer, a write pointer,
control signals (RCLK, WCLK, REN1, REN2, WEN1, WEN2,
RS), and flags (EF, PAE, PAF, FF).
Resetting the FIFO
Upon power-up, the FIFO must be reset with a Reset (RS)
cycle. This causes the FIFO to enter the Empty condition
signified by EF being LOW. All data outputs (Q0–8) go LOW
tRSF after the rising edge of RS. In order for the FIFO to reset
to its default state, the user must not read or write while RS is
LOW. All flags are guaranteed to be valid tRSF after RS is taken
LOW.
FIFO Operation
When the WEN1 signal is active LOW, WEN2 is active HIGH,
and FF is active HIGH, data present on the D0–8 pins is written
into the FIFO on each rising edge of the WCLK signal.
Similarly, when the REN1 and REN2 signals are active LOW
and EF is active HIGH, data in the FIFO memory will be
presented on the Q0-8 outputs. New data will be presented on
each rising edge of RCLK while REN1 and REN2 are active.
REN1 and REN2 must set up tENS before RCLK for it to be a
valid read function. WEN1 and WEN2 must occur tENS before
WCLK for it to be a valid write function.
An output enable (OE) pin is provided to three-state the Q0–8
outputs when OE is asserted. When OE is enabled (LOW),
Document #: 38-06013 Rev. *B
data in the output register will be available to the Q0-8 outputs
after tOE. If devices are cascaded, the OE function will only
output data on the FIFO that is read enabled.
The FIFO contains overflow circuitry to disallow additional
writes when the FIFO is full, and underflow circuitry to disallow
additional reads when the FIFO is empty. An empty FIFO
maintains the data of the last valid read on its Q0-8 outputs
even after additional reads occur.
Write Enable 1 (WEN1). If the FIFO is configured for programmable flags, Write Enable 1 (WEN1) is the only write enable
control pin. In this configuration, when Write Enable 1 (WEN1)
is LOW, data can be loaded into the input register and RAM
array on the LOW-to-HIGH transition of every write clock
(WCLK). Data is stored is the RAM array sequentially and
independently of any on-going read operation.
Write Enable 2/Load (WEN2/LD). This is a dual-purpose pin.
The FIFO is configured at Reset to have programmable flags
or to have two write enables, which allows for depth
expansion. If Write Enable 2/Load (WEN2/LD) is set active
HIGH at Reset (RS = LOW), this pin operates as a second
write enable pin.
If the FIFO is configured to have two write enables, when Write
Enable (WEN1) is LOW and Write Enable 2/Load (WEN2/LD)
is HIGH, data can be loaded into the input register and RAM
array on the LOW-to-HIGH transition of every write clock
(WCLK). Data is stored in the RAM array sequentially and
independently of any on-going read operation.
Programming
When WEN2/LD is held LOW during Reset, this pin is the load
(LD) enable for flag offset programming. In this configuration,
WEN2/LD can be used to access the four 9-bit offset registers
contained in the CY7C4261/71/81/91V for writing or reading
data to these registers.
When the device is configured for programmable flags and
both WEN2/LD and WEN1 are LOW, the first LOW-to-HIGH
transition of WCLK writes data from the data inputs to the
empty offset least significant bit (LSB) register. The second,
third, and fourth LOW-to-HIGH transitions of WCLK store data
in the empty offset most significant bit (MSB) register, full
offset LSB register, and full offset MSB register, respectively,
when WEN2/LD and WEN1 are LOW. The fifth LOW-to-HIGH
transition of WCLK while WEN2/LD and WEN1 are LOW
writes data to the empty LSB register again. Figure 1 shows
the registers sizes and default values for the various device
types.
Page 3 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
8
0
7
8
Empty Offset (LSB) Reg.
Default Value = 007h
0
5
0
7
Empty Offset (LSB) Reg.
Default Value = 007h
8
6
8
0
8
7
Full Offset (LSB) Reg
Default Value = 007h
8
128k x 9
0
8
Empty Offset (LSB) Reg.
Default Value = 007h
0
(MSB)
Default Value = 000h
0
8
Full Offset (LSB) Reg
Default Value = 007h
(MSB)
Default Value = 000h
WEN
WCLK
Selection
0
0
0
1
No Operation
1
0
Write Into FIFO
1
1
No Operation
Empty Offset (LSB)
Empty Offset (MSB)
Full Offset (LSB)
Full Offset (MSB)
0
7
Full Offset (LSB) Reg
Default Value = 007h
0
8 7
LD
0
8
(MSB)
Default Value = 000h
8 7
0
7
Empty Offset (LSB) Reg.
Default Value = 007h
8 7
Table 1. Writing the Offset Registers[1]
(MSB)
Default Value = 000h
64k x 9
7
0
0
6
8
(MSB)
Default Value = 000h
8
0
Full Offset (LSB) Reg
Default Value = 007h
0
5
Programmable Flag (PAE, PAF) Operation
Whether the flag offset registers are programmed as
described in Table 1 or the default values are used, the
programmable almost-empty flag (PAE) and programmable
almost-full flag (PAF) states are determined by their corresponding offset registers and the difference between the read
and write pointers.
(MSB)
Default Value = 000h
(MSB)
Default Value = 000h
8 7
contents to the data outputs. Writes and reads should not be
performed simultaneously on the offset registers.
32k x 9
16k x 9
0
8
(MSB)
Default Value = 000h
Figure 1. Offset Register Location and Default Values
It is not necessary to write to all the offset registers at one time.
A subset of the offset registers can be written; then by bringing
the WEN2/LD input HIGH, the FIFO is returned to normal read
and write operation. The next time WEN2/LD is brought LOW,
a write operation stores data in the next offset register in
sequence.
The contents of the offset registers can be read to the data
outputs when WEN2/LD is LOW and both REN1 and REN2
are LOW. LOW-to-HIGH transitions of RCLK read register
The number formed by the empty offset least significant bit
register and empty offset most significant bit register is
referred to as n and determines the operation of PAE. PAF is
synchronized to the LOW-to-HIGH transition of RCLK by one
flip-flop and is LOW when the FIFO contains n or fewer unread
words. PAE is set HIGH by the LOW-to-HIGH transition of
RCLK when the FIFO contains (n+1) or greater unread words.
The number formed by the full offset least significant bit
register and full offset most significant bit register is referred to
as m and determines the operation of PAF. PAE is synchronized
to the LOW-to-HIGH transition of WCLK by one flip-flop and is
set LOW when the number of unread words in the FIFO is
greater than or equal to CY7C4261V (16k – m), CY7C4271V
(32k – m), CY7C4281V (64k – m) and CY7C4291V
(128k – m). PAF is set HIGH by the LOW-to-HIGH transition
of WCLK when the number of available memory locations is
greater than m.
Note:
1. The same selection sequence applies to reading from the registers. REN1 and REN2 are enabled and a read is performed on the LOW-to-HIGH transition of RCLK.
Document #: 38-06013 Rev. *B
Page 4 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Table 2. Status Flags
Number of Words in FIFO
CY7C4261V
CY7C4271V
CY7C4281V
CY7C4291V
FF PAF PAE EF
0
0
0
0
H
H
L
L
1 to n[2]
1 to n[2]
1 to n[2]
1 to n[2]
H
H
L
H
H
H
H
H
(n + 1) to (1638 − (m + 1)) (n + 1) to (32768 − (m + 1)) (n + 1) to (65536 − (m + 1)) (n + 1) to (131072 −
(m + 1))
(16384 − m)[3] to 16383
(32768 − m)[3] to 32767
(65536 − m)[3] to 65535
(131072 − m)[3] to 131071 H
L
H
H
16384
32768
65536
131072
L
H
H
L
Width-Expansion Configuration
Flag Operation
Word width may be increased simply by connecting the corresponding input controls signals of multiple devices. A
composite flag should be created for each of the end-point
status flags (EF and FF). The partial status flags (PAE and
PAF) can be detected from any one device. Figure 2 demonstrates a 18-bit word width by using two CY7C42x1Vs. Any
word width can be attained by adding additional CY7C42x1Vs.
The CY7C4261/71/81/91V devices provide five flag pins to
indicate the condition of the FIFO contents. Empty, Full, PAE,
and PAF are synchronous.
When the CY7C42x1V is in a Width-Expansion Configuration,
the Read Enable (REN2) control input can be grounded (see
Figure 2). In this configuration, the Write Enable 2/Load
(WEN2/LD) pin is set to LOW at Reset so that the pin operates
as a control to load and read the programmable flag offsets.
Full Flag
The Full Flag (FF) will go LOW when the device is full. Write
operations are inhibited whenever FF is LOW regardless of the
state of WEN1 and WEN2/LD. FF is synchronized to WCLK,
i.e., it is exclusively updated by each rising edge of WCLK.
Empty Flag
The Empty Flag (EF) will go LOW when the device is empty.
Read operations are inhibited whenever EF is LOW,
regardless of the state of REN1 and REN2. EF is synchronized
to RCLK, i.e., it is exclusively updated by each rising edge of
RCLK.
RESET (RS)
DATA IN (D) 18
RESET (RS)
9
9
READ CLOCK (RCLK)
WRITECLOCK (WCLK)
READ ENABLE 1 (REN1)
WRITE ENABLE 1(WEN1)
OUTPUT ENABLE (OE)
WRITE ENABLE 2/LOAD
(WEN2/LD)
CY7C4261V
CY7C4271V
CY7C4281V
CY7C4291V
PROGRAMMABLE(PAF)
FULL FLAG (FF) # 1
FF
CY7C4261V
CY7C4271V
CY7C4281V
CY7C4291V
FF
EF
PROGRAMMABLE(PAE)
EMPTY FLAG (EF) #1
EMPTY FLAG (EF) #2
EF
9
FULL FLAG (FF) # 2
DATA OUT (Q)
18
9
Read Enable 2 (REN2)
Read Enable 2 (REN2)
Figure 2. Block Diagram of 16k/32k/64k/128k x 9 Low-Voltage Deep Sync FIFO Memory
Used in a Width-Expansion Configuration
Notes:
2. n = Empty Offset (n = 7 default value).
3. m = Full Offset (m = 7 default value).
Document #: 38-06013 Rev. *B
Page 5 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Maximum Ratings
DC Input Voltage ................................... –0.5V to VCC + 0.5V
Output Current into Outputs (LOW)............................. 20 mA
(Above which the useful life may be impaired. For user guidelines, not tested.)
Static Discharge Voltage........................................... > 2001V
(per MIL-STD-883, Method 3015)
Storage Temperature ...................................–65°C to +150°C
Latch-up Current..................................................... > 200 mA
Ambient Temperature with
Power Applied...............................................–55°C to +125°C
Operating Range
Supply Voltage to Ground Potential ............... –0.5V to +3.6V
Range
DC Voltage Applied to Outputs
in High-Z State .......................................–0.5V to VCC + 0.5V
VCC[4]
Ambient Temperature
0°C to +70°C
3.3V ±300 mV
−40°C to +85°C
3.3V ±300 mV
Commercial
Industrial
Electrical Characteristics Over the Operating Range
7C4261/71/81/91V- 7C4261/71/81/91V- 7C4261/71/81/91V10
15
25
Parameter
Description
Test Conditions
Min.
2.4
Max.
Min.
Max.
VOH
Output HIGH
Voltage
VCC = Min., IOH = −1.0 mA
VCC = 3.0V, IOH = −2.0 mA
VOL
Output LOW
Voltage
VCC = Min., IOL = 4.0 mA
VCC = 3.0V, IOL = 8.0 mA
VIH
Input HIGH
Voltage
2.0
VCC
2.0
VCC
VIL
Input LOW
Voltage
−0.5
0.8
−0.5
IIX
Input Leakage
Current
VCC = Max.
−10
+10
IOZL
IOZH
Output OFF,
High Z Current
OE > VIH,
VSS < VO< VCC
−10
+10
ICC1[5]
Active Power
Supply Current
Com’l
Average
Standby Current
Com’l
ISB[6]
Min.
2.4
.04
Max.
2.4
Unit
V
0.4
0.4
V
2.0
VCC
V
0.8
−0.5
0.8
V
−10
+10
−10
+10
µA
−10
+10
−10
+10
µA
25
mA
25
25
Ind
30
4
mA
4
Ind
4
mA
4
mA
Capacitance[7]
Parameter
Description
CIN
Input Capacitance
COUT
Output Capacitance
Test Conditions
TA = 25°C, f = 1 MHz,
VCC = 3.3V
Max.
Unit
5
pF
7
pF
AC Test Loads and Waveforms (-15 and -25)[8, 9]
R1 = 330Ω
All Input Pulses
3.3V
OUTPUT
Equivalent to:
CL
R2=510Ω
INCLUDING
JIG AND
SCOPE
THÉVENIN EQUIVALENT
200 Ω
OUTPUT
2.0V
3.0V
90%
10%
GND
≤ 3 ns
90%
10%
≤ 3 ns
Notes:
4. VCC Range for commercial -10 ns is 3.3V ±150mV.
5. Input signals switch from 0V to 3V with a rise/fall time of less than 3 ns, clocks and clock enables switch at maximum frequency of 20 MHz, while data inputs
switch at 10 MHz. Outputs are unloaded.)
6. All inputs = VCC − 0.2V, except WCLK and RCLK (which are at frequency = 0 MHz). All outputs are unloaded.
7. Tested initially and after any design or process changes that may affect these parameters.
8. CL = 30 pF for all AC parameters except for tOHZ.
9. CL = 5 pF for tOHZ.
Document #: 38-06013 Rev. *B
Page 6 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
AC Test Loads and Waveforms (continued) (-10)
VCC/2
All Input Pulses
50Ω
3.0V
I/O
Z0 = 50Ω
90%
10%
90%
10%
GND
≤ 3 ns
≤ 3 ns
Switching Characteristics Over the Operating Range
7C4261/71/81/91V- 7C4261/71/81/91V- 7C4261/71/81/91V10
15
25
Parameter
Description
Min.
Max.
Min.
100
Max.
Min.
Unit
40
MHz
Clock Cycle Frequency
tA
Data Access Time
2
tCLK
Clock Cycle Time
10
tCLKH
Clock HIGH Time
4.5
6
10
ns
tCLKL
Clock LOW Time
4.5
6
10
ns
tDS
Data Set-up Time
3.5
4
6
ns
tDH
Data Hold Time
0
0
1
ns
tENS
Enable Set-up Time
3.5
4
6
ns
tENH
Enable Hold Time
0
0
1
ns
tRS
Reset Pulse Width[10]
10
15
25
ns
tRSS
Reset Set-up Time
8
10
15
ns
tRSR
Reset Recovery Time
8
tRSF
Reset to Flag and Output Time
tOLZ
Output Enable to Output in Low Z[11]
0
tOE
Output Enable to Output Valid
3
8
66.7
Max.
tS
2
2
0
3
7
3
ns
25
0
10
3
8
3
ns
ns
15
15
7
15
25
10
10
Z[11]
10
15
ns
ns
12
ns
tOHZ
Output Enable to Output in High
tWFF
Write Clock to Full Flag
tREF
Read Clock to Empty Flag
8
10
15
ns
tPAF
Clock to Programmable Almost-Full Flag
8
10
15
ns
tPAE
Clock to Programmable Almost-Full Flag
15
ns
tSKEW1
Skew Time between Read Clock and Write
Clock for Empty Flag and Full Flag
5
6
10
ns
tSKEW2
Skew Time between Read Clock and Write
Clock for Almost-Empty Flag and
Almost-Full Flag
10
15
18
ns
3
8
10
8
10
12
ns
15
ns
Notes:
10. Pulse widths less than minimum values are not allowed.
11. Values guaranteed by design, not currently tested.
Document #: 38-06013 Rev. *B
Page 7 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Switching Waveforms
Write Cycle Timing
tCLK
tCLKH
tCLKL
WCLK
tDS
tDH
D0 –D17
tENS
tENH
WEN1
NO OPERATION
NO OPERATION
WEN2
(if applicable)
tWFF
tWFF
FF
tSKEW1 [12]
RCLK
REN1, REN2
Read Cycle Timing
tCKL
tCLKH
tCLKL
RCLK
tENS
tENH
REN1, REN2
NO OPERATION
tREF
tREF
EF
tA
Q0 –Q17
VALID DATA
tOLZ
tOHZ
tOE
OE
tSKEW1[13]
WCLK
WEN1
WEN2
Notes:
12. tSKEW1 is the minimum time between a rising RCLK edge and a rising WCLK edge to guarantee that FF will go HIGH during the current clock cycle. If the time
between the rising edge of RCLK and the rising edge of WCLK is less than tSKEW1, then FF may not change state until the next WCLK rising edge.
13. tSKEW1 is the minimum time between a rising WCLK edge and a rising RCLK edge to guarantee that EF will go HIGH during the current clock cycle. It the time
between the rising edge of WCLK and the rising edge of RCLK is less than tSKEW2, then EF may not change state until the next RCLK rising edge.
Document #: 38-06013 Rev. *B
Page 8 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Switching Waveforms (continued)
Reset Timing[14]
RS
tRS
tRSS
tRSR
tRSS
tRSR
tRSS
tRSR
REN1,
REN2
WEN1
WEN2/LD
[16]
tRSF
EF,PAE
tRSF
FF, PAF
tRSF
Q0 − Q8
[15]
OE = 1
OE=0
Notes:
14. The clocks (RCLK, WCLK) can be free-running during reset.
15. After reset, the outputs will be LOW if OE = 0 and three-state if OE=1.
16. Holding WEN2/LD HIGH during reset will make the pin act as a second enable pin. Holding WEN2/LD LOW during reset will make the pin act as a load enable
for the programmable flag offset registers.
Document #: 38-06013 Rev. *B
Page 9 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Switching Waveforms (continued)
First Data Word Latency after Reset with Read and Write
WCLK
tDS
D0 –D8
D0(FIRST VALID WRITE)
D1
D2
D3
D4
tENS
tFRL [17]
WEN1
WEN2
(if applicable)
tSKEW1
RCLK
tREF
EF
tA
tA [18]
REN1,
REN2
Q0 –Q8
D0
tOLZ
D1
tOE
OE
Notes:
17. When tSKEW1 > minimum specification, tFRL (maximum) = tCLK + tSKEW2. When tSKEW1 < minimum specification, tFRL (maximum) = either 2*tCLK + tSKEW1 or tCLK
+ tSKEW1. The Latency Timing applies only at the Empty Boundary (EF = LOW).
18. The first word is available the cycle after EF goes HIGH, always.
Document #: 38-06013 Rev. *B
Page 10 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Switching Waveforms (continued)
Empty Flag Timing
WCLK
tDS
tDS
DATA WRITE 2
DATA WRITE 1
D0 –D8
tENH
tENS
tENH
tENS
WEN1
tENS
tENH
tENS
tENH
WEN2
(if applicable)
tFRL [17]
tFRL [17]
RCLK
tSKEW1
tREF
tREF
tREF
tSKEW1
EF
REN1,
REN2
LOW
OE
tA
Q0 –Q8
DATA IN OUTPUT REGISTER
Document #: 38-06013 Rev. *B
DATA READ
Page 11 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Switching Waveforms (continued)
Full Flag Timing
NO WRITE
NO WRITE
WCLK
tSKEW1[12]
tSKEW1[12]
tDS
DATA WRITE
DATA WRITE
D0 –D8
tWFF
tWFF
tWFF
FF
WEN1
WEN2
(if applicable)
RCLK
tENS
REN1,
REN2
OE
tENH
tENS
LOW
tA
Q0 –Q8
tENH
tA
DATA READ
DATA IN OUTPUT REGISTER
NEXT DATA READ
Programmable Almost Empty Flag Timing
tCLKL
tCLKH
WCLK
tENS tENH
WEN1
WEN2
(if applicable)
tENS tENH
Note 20
PAE
N + 1 WORDS
IN FIFO
tSKEW2 [19]
tPAE
Note21
tPAE
RCLK
tENS
tENS tENH
REN1,
REN2
Notes:
19. tSKEW2 is the minimum time between a rising WCLK and a rising RCLK edge for PAE to change state during that clock cycle. If the time between the edge of
WCLK and the rising RCLK is less than tSKEW2, then PAE may not change state until the next RCLK.
20. PAE offset = n.
21. If a read is performed on this rising edge of the read clock, there will be Empty + (n−1) words in the FIFO when PAE goes LOW.
Document #: 38-06013 Rev. *B
Page 12 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Switching Waveforms (continued)
Programmable Almost Full Flag Timing
tCLKL
tCLKH
Note 22
WCLK
tENS tENH
WEN1
Note 23
WEN2
(if applicable)
tPAF
tENS tENH
PAF
(FULL −M) WORDS
IN FIFO [24]
FULL − (M+1)WORDS
IN FIFO
tSKEW2 [25]
tPAF
RCLK
tENS
tENS tENH
REN1,
REN2
Write Programmable Registers
tCLK
tCLKL
tCLKH
WCLK
tENS
tENH
WEN2/LD
tENS
WEN1
tDS
tDH
D0 –D8
PAE OFFSET
LSB
PAE OFFSET
MSB
PAF OFFSET
LSB
PAF OFFSET
MSB
Notes:
22. If a write is performed on this rising edge of the write clock, there will be Full − (m−1) words of the FIFO when PAF goes LOW.
23. PAF offset = m.
24. 16K − m words for CY7C4261V, 32K – m words for CY7C4271V, 64K − m words for CY7C4281V, and 128K − m words for CY4291V.
25. tSKEW2 is the minimum time between a rising RCLK edge and a rising WCLK edge for PAF to change during that clock cycle. If the time between the rising edge
of RCLK and the rising edge of WCLK is less than tSKEW2, then PAF may not change state until the next WCLK.
Document #: 38-06013 Rev. *B
Page 13 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Switching Waveforms (continued)
Read Programmable Registers
tCLK
tCLKL
tCLKH
RCLK
tENS
tENH
WEN2/LD
tENS
PAF OFFSET
MSB
REN1,
REN2
tA
UNKNOWN
Q0 –Q15
PAE OFFSET LSB
PAE OFFSET MSB
PAF OFFSET
LSB
Ordering Information
16Kx9 Low-voltage Deep Sync FIFO
Speed (ns)
10
15
25
Ordering Code
Package Name
Package Type
Operating Range
CY7C4261V-10JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
CY7C4261V-10JXC
J65
32-Lead Pb-Free Plastic Leaded Chip Carrier
Commercial
CY7C4261V-15JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
CY7C4261V-15JXC
J65
32-Lead Pb-Free Plastic Leaded Chip Carrier
Commercial
CY7C4261V-15JI
J65
32-Lead Plastic Leaded Chip Carrier
Industrial
CY7C4261V-25JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
32Kx9 Low-voltage Deep Sync FIFO
Speed (ns)
10
15
25
Ordering Code
Package Name
Package Type
Operating Range
CY7C4271V-10JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
CY7C4271V-10JXC
J65
32-Lead Pb-Free Plastic Leaded Chip Carrier
Commercial
CY7C4271V-15JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
CY7C4271V-15JI
J65
32-Lead Plastic Leaded Chip Carrier
Industrial
CY7C4271V-25JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
64kx9 Low-voltage Deep Sync FIFO
Speed (ns)
10
15
25
Ordering Code
Package Name
Package Type
Operating Range
CY7C4281V-10JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
CY7C4281V-10JXC
J65
32-Lead Pb-Free Plastic Leaded Chip Carrier
Commercial
CY7C4281V-15JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
CY7C4281V-15JI
J65
32-Lead Plastic Leaded Chip Carrier
Industrial
CY7C4281V-25JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
128kx9 Low-voltage Deep Sync FIFO
Speed (ns)
10
15
25
Ordering Code
Package Name
Package Type
Operating Range
CY7C4291V-10JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
CY7C4291V-10JXC
J65
32-Lead Pb-Free Plastic Leaded Chip Carrier
Commercial
CY7C4291V-15JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
CY7C4291V-15JXC
J65
32-Lead Pb-Free Plastic Leaded Chip Carrier
Commercial
CY7C4291V-15JI
J65
32-Lead Plastic Leaded Chip Carrier
Industrial
CY7C4291V-25JC
J65
32-Lead Plastic Leaded Chip Carrier
Commercial
Document #: 38-06013 Rev. *B
Page 14 of 16
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Package Diagram
32-Lead Plastic Leaded Chip Carrier J65
32-Lead Pb-Free Plastic Leaded Chip Carrier J65
51-85002-*B
Deep Sync is a trademark of Cypress Semiconductor. All product and company names mentioned in this document are the
trademarks of their respective holders.
Document #: 38-06013 Rev. *B
Page 15 of 16
© Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY7C4261V/CY7C4271V
CY7C4281V/CY7C4291V
Document History Page
Document Title: CY7C4261V/CY7C4271V/CY7C4281V/CY7C4291V 16K/32K/64K/128K/X9 Low-Voltage Deep Sync FIFO
Document Number: 38-06013
REV.
ECN NO. Issue Date
Orig. of
Change
Description of Change
**
106474
09/15/01
SZV
Changed Spec number from 38-00656 to 38-06013
*A
127858
09/04/03
FSG
Changed: tSKEW2 to tSKEW1 in Switching Waveforms “Empty Flag Timing” diagram
Fixed flag timing diagram in Switching Waveforms section
*B
386127
See ECN
ESH
Added Pb-Free logo to top of front page
Added CY7C4291V-15JXC, CY7C91V-10JXC, CY7C4281V-10JXC,
CY7C4271V-10JXC, CY7C4261V-10JXC, CY7C4261V-15JXC to ordering information.
Document #: 38-06013 Rev. *B
Page 16 of 16