YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator Features Description The YB1210R is a series of ultra-low-noise, low dropout (LDO) linear regulators with 2.0% output voltage accuracy. The YB1210R regulators achieve a low 320mV dropout at 300mA load current of 3.3V output and are available in voltages ranging from 1.2V to 3.6V with 0.1 V per step (custom voltage is considerable at request). The YB1210R regulators are optimized to work with low-ESR and low cost ceramic capacitors, reducing the amount of board space critical in portable devices. The YB1210R requires only 1.0 μF output capacitor for stability with any load and consumes less than 1μA in shutdown mode. Built-in thermal shutdown and short-circuit protect offer secure protection against fault operation. The YB1210R regulators are available in SOT-23 / SOT-25 / SOT-89 packages. • • • • • • • • • • • • High Accuracy Output Voltage : + 2% Wide Output Voltage Range : 1.2~3.6V Ultra-Low-Noise Low-Drop-Out Typical Output Current : 300 mA Low Quiescent Current: ~60μA 320mV Dropout at 300mA 3.3V Output Stable with 1.0μF Ceramic Capacitor Only Need Input and Output Capacitors Thermal Protection Shutdown Output Short-Circuit Current Limit Built-In Internal Soft-Start Green Package (RoHS) Available Applications • • • • • • • • PDA, Notebook, PC Computers DSC, Handset Camera Modules PCMCIA Cards, PC Cameras USB Based Portable Devices GSM/GPRS/3G RF Transceiver Wireless LANs Bluetooth Portable Radios Battery-Powered Devices Typical Application Circuitry YB1210R MRev. 1.4 www.yobon.com.tw 1 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator Pin Configuration Pin Description Table 1 Pin Name Pin Function VIN Unregulated Input Supply. Bypass with a capacitor to GND. GND Ground pin. EN Pull high to enable the regulator. N.C. or BYPASS Connect a 33nF capacitor to GND for low noise operation or N.C. VOUT Regulated Output Voltage. Bypass with a capacitor to GND. YB1210R MRev. 1.4 www.yobon.com.tw 2 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator Ordering Information Marking Information Absolute Maximum Ratings Recommended Operating Conditions Supply Voltage ................................................ -0.3V to 7.0V Input Supply Voltage.........................................2V to 6.0V Output Voltage ....................................... -0.3V to (VIN+0.3V) Operating Temperature............................ -40℃ to +85℃ Output Short-Circuit Duration.....................................Infinite ESD Susceptibility (HBM)...........................................2KV Junction Temperature Range ...................................+150℃ ESD Susceptibility (MM)........................................... 200V Storage Temperature Range..................... -65℃ to +150℃ Thermal Resistance (SOT-23/25, θJC) ...............140℃/W Lead Temperature ....................................................+250℃ Thermal Resistance (SOT-89, θJC) ......................46℃/W Thermal Resistance (SOT-23/25, θJA)................280℃/W Thermal Resistance (SOT-89, θJA).....................180℃/W Internal Power Dissipation (SOT-23/25, PD)............. 0.4W Internal Power Dissipation (SOT-89, PD)................ 0.55W YB1210R MRev. 1.4 www.yobon.com.tw 3 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator Electrical Characteristics Table 2 TA = 25℃, VIN = ( VOUT + 1 V ), CIN = COU T = 1.0μF, VEN = VIN, unless otherwise noted Function Parameter Conditions Max Units 2.0 6.0 V Predefined 1.2 3.6 V IOUT = 10mA, VOUT >= 1.3V -2.0 +2.0 % IOUT = 10mA, VOUT = 1.2V 0 +4.0 % Input Voltage Range Output Voltage Output Voltage Accuracy Output Current Limit Min Typ Short-circuit output 50 Vout = 3.6V, Iout = 300 mA 300 Vout = 3.0V, Iout = 300 mA 350 Vout = 2.5V, Iout = 300 mA 450 Vout = 1.5V, Iout = 300 mA 700 Vout = 1.2V, Iout = 300 mA 870 Ground Current Iground = Iin - Iout 60 Line Regulation Vin = (Vout + 1V) to 6V, Iout = 10 mA 0.30 0.40 %/V Load Regulation Iout = 1mA to 300 mA 1.0 1.5 % Shutdown Supply Current EN = 0.4V 0.01 Dropout Voltage (Note 1) Ripple Rejection (PSRR) Start Up Delay (Note 2) Shutdown Delay (Note 3) mA mV μA μA f = 1KHz, Iout = 1 mA 50 f = 10KHz, Iout = 1 mA 60 f = 100 KHz, Iout = 1 mA 40 Rload=100ohm,Cbypass=0nF 20 50 μS Rload=100 ohm, Cbypass=33nF 2 3.5 mS Rload=10K ohm, VOUT=1.5V 1 mS Rload=10K ohm, VOUT=1.2V 1 mS dB EN Logic Low Level Vin = 2.0V to 6.0V EN Logic High Level Vin = 2.0V to 6.0 V EN Input Bias Current Vin = EN = Vout + 1V 0.01 μA Thermal Shutdown Shutdown Temperature 160 °C 20 °C Thermal Hysteresis 1.2 0.4 V Vin V Note1 : The drop out voltage varies depending on output voltage selection. Dropout is defined as VIN–VOUT when VOUT is 100mV below VOUT where Vin=Vout + 1V for nominal VOUT. Note 2: Time needed for VOUT to reach 90% of final value. Note 3: Time needed for VOUT to discharge below 0.5V. YB1210R MRev. 1.4 www.yobon.com.tw 4 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator Typical Characteristics At TA=25℃, VIN=(VOUT+1V), CIN=COUT=1.0μF, VEN=VIN, unless otherwise noted. YB1210R MRev. 1.4 www.yobon.com.tw 5 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator YB1210R MRev. 1.4 www.yobon.com.tw 6 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator YB1210R MRev. 1.4 www.yobon.com.tw 7 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator Functional Block Diagram Functional Description The YB1210R is an ultra-low-noise, low-quiescent current, low-dropout linear regulator. It is supplied in a SOT-23 / SOT-25 / SOT-89 package for different applications. YB1210R can supply loads up to 300mA (typical operation, not maximum) and output voltages are preset and ranging from 1.2V to 3.6V. than the reference voltage, the gate of the pass-transistor is pulled low. This allows more current to pass to the output and increases the output voltage. If the feedback voltage is too high, the gate of the pass transistor is pulled high, allowing less current to pass to the output. As shown in the Functional Block Diagram, the YB1210R consists of a reference and noise bypass circuit, error amplifier, output drive transistor, internal feedback voltage divider, thermal sensor, and short circuit current limiter. The YB1210R is a high performance LDO emphasizing stability with low output capacitance. It is able to maintain stability with an output capacitor as low as 1.0 uF. The output capacitor can also be increased to optimize performance. The YB1210R will remain stable and in regulation with no load, unlike many other voltage regulators. The internal reference is connected to the error amplifier’s inverting input. The error amplifier compares this reference with the feedback voltage and amplifies the difference. If the feedback voltage is lower YB1210R MRev. 1.4 Stability Internal P-Channel Pass Transistor The YB1210R features a low impedance www.yobon.com.tw 8 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator P-channel MOSFET pass transistor. This provides several advantages over similar designs using a PNP pass transistor, including low operating power and longer battery life. The YB1210R consumes only 60µA of quiescent current under most conditions. Output Short-Circuit Current Limit The YB1210R includes a current limiter, which monitors and controls the pass transistor’s gate voltage, limiting the output current to about 200mA, for example, in a short-circuit output situation. Shutdown The YB1210R also features a low-power active shutdown mode. It has a switch that turns off the device when disabled. This allows the output capacitor and load to discharge and de-energize the load. In the shutdown mode, the internal functional blocks, such as voltage reference and the error amplifier, are turned off completely, and the quiescent current is less than 1µA. Thermal Protection Shutdown The thermal protection shutdown function protects the device from operating in over temperature condition. When the junction temperature exceeds +160°C, the thermal sensor signals the shutdown logic, turning off the pass transistor and allowing the IC to cool down. The thermal sensor turns the pass transistor on again after the IC’s junction temperature drops to +140°C. from abnormal operation at the beginning of shutdown mode. Soft-Start Circuitry The YB1210R includes a soft-start circuitry to limit inrush current at turn-on. During power up, the output capacitor and output load are charged with a reduced output current. Shortly after the initial power up, the soft-start feature is terminated and normal operation is resumed. Application Information Enable/Shutdown The YB1210R comes with an active-high enable pin that allows the regulator to be enabled. Forcing the enable pin low disables the regulator and puts it into the shutdown mode. This pin cannot be left floating as it may cause an undetermined state. Input/Output Capacitor It is recommended to use a 1.0µF capacitor on the YB1210R input and a 1.0µF capacitor on the output. For high regulation performance, larger input capacitor values and lower ESRs provide better noise rejection and line-transient response. The output noise, load-transient response, stability, and power-supply rejection can be improved by using large output capacitors. Low ESR ceramic capacitors provide optimal performance and save space. Auto-Discharge Circuitry The YB1210R deploys a NMOS connecting between VOUT and ground. When EN pin is pulled low, the NMOS is activated by an inverted signal from EN. The charge kept on output capacitor is discharged quickly through the NMOS. It prevents the system YB1210R MRev. 1.4 www.yobon.com.tw 9 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator SOT-25 Package Information YB1210R MRev. 1.4 www.yobon.com.tw 10 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator SOT-23 Package Information NOTE: 1. ALL DIMENSIONS ARE IN MILLIMETERS. 2. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSION OR GATE BURRS SHALL NOT EXCEED 0.25mm PER END. DIMENSION E1 DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 PER SIDE. 3. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM. DIMENSIONS D AND E1 ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, THE BAR BURRS. GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETEEN THE TOP AND BOTTOM OF THE PLASTIC BODY.. 4. DIMENSION“b＂DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08mm TOTAL IN EXCESS OF THE “b＂DIMENSION AT MAXIMUM MATERIAL CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OF THE FOOT . MINMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT LEAD SHALL NOT BE LESS THAN 0.07mm 5. LEAD FRAME MATERIAL:EFTEC 64T YB1210R MRev. 1.4 www.yobon.com.tw 11 YB1210R 300mA, Ultra-Low-Noise, High PSRR LDO Regulator SOT-89 Package Information YB1210R MRev. 1.4 www.yobon.com.tw 12