S-AU86 TOSHIBA RF POWER AMPLIFIER MODULE S-AU86 ○RF POWER AMPLIFIER MODULE for 800MHz Digital MCA ABSOLUTE MAXIMUM RATINGS (Tc = 25℃, ZG = ZL = 50Ω) CHARACTERISTIC SYMBOL RATING UNIT DC Supply Voltage VDD 17 V DC Supply Voltage VGG 9 V Pi 320 mW Tc (opr) -30~100 ℃ Tstg -40~110 ℃ Input Power Operating Case Temperature Range Storage Temperature Range Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Caution: This absolute maximum rating given in a sheet guarantees each item independently. When two items or more of maximum rated items joins a device at once. It becomes the outside of a guarantee. Please design in circuit to make it always operate within this regulation also on the worst condition. PACKAGE OUTLINE 1 2007-11-01 S-AU86 ELECTRICAL CHARACTERISTICS (Tc = 25℃, ZG = 50Ω) CHARACTERISTIC SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT frange — 889 — 915 MHz Output Power Po VDD = 12.0V, IDD = 1.7A (VGG = adjust) Po = 20dBmW, ZL = 50Ω 40 — — dBmW Input Power Pi VDD = 12.0V, IDD = 1.7A (VGG = adjust) Po = 35dBmW ZL = 50Ω — — 7 dBmW Gate Bias Voltage VGG VDD = 12.0V, IDD = 1.7A (VGG = adjust) Po = 35dBmW (Pi= adjust), ZL = 50Ω — — 8 V Gate Bias Current IGGBias VDD = 12.0V, IDD = 1.7A (VGG = adjust) Po = 35dBmW (Pi= adjust), ZL = 50Ω After that Pi OFF — — 10 mA ACP VDD = 12.0V, IDD = 1.7A (VGG = adjust) Po = 35dBmW (Pi= adjust), ZL = 50Ω Modulated Wave :ππ/4·DQPSK (α=0.5, 32kbps) Band Width : 16kHz Frequency Offset : 25kHz — — -39 dB — — -30 dB — — -30 dB — — -35 dB — — ±5 ° Frequency Range Adjacent-Channel Power Ratio Second Harmonic Third Harmonic Harmonic 2nd HRM 3rd HRM VDD = 12.0V, IDD = 1.7A (VGG = adjust) Po = 35dBmW (Pi= adjust), ZL = 50Ω HRM Ralative Phase Variation — VDD= 12.0V, IDD = 1.7A (VGG = adjust) ZL = 50Ω,0° (@Po = 35dBmW) Po = 5 to 40dBmW Load Mismatch — VDD = 12.0V, IDD = 1.7A (VGG = adjust) Pi = 40dBmW (Pi= adjust, @ZL = 50Ω VSWR LOAD 20: 1 ALL PHASE No Degradation — Stability — VDD = 10.0 to 16.0V, VGG = 1.0 to 9.0V Pi = -40 to 25dBmW VSWR LOAD 6: 1 ALL PHASE All spurious output than 60dB below desired signal — Caution ･ This product has intersetting cap. Please pay attention for exceeding stress and foreign matter in your application. And not to take away the cap. ･ Do not break, cut, crush or dissolve chemically. Dispose of this product properly according to law. Do not intermingle with normal industrial or domestic waste. ･ This product is electrostatic sensitivity, please handle with caution. 2 2007-11-01 S-AU86 SCHEMATIC ④ Po ZL=50Ω ① Pi ZG=50Ω ② VGG ③ VDD TEST FIXTURE ⑤ GROUND (FRANGE) C:10000pF,10μF PARALLEL L:φ 0.8 ENAMEL WIRE､5T､3ID 3 2007-11-01 S-AU86 RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 4 2007-11-01