MAXIM MAX8971EWP+

19-4245; Rev 0; 1/12
EVALUATION KIT AVAILABLE
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
General Description
Benefits and Features
The MAX8971 is a compact, high-frequency, highefficiency switch-mode charger for a one-cell lithium-ion
(Li+) battery. It delivers up to 1.55A of current to the
battery from inputs up to 7.5V and withstands transient
inputs up to 22V. The 4MHz switch-mode charger is
ideally suited for small portable devices, such as headsets and ultra-portable media players. It minimizes
component size and heat.
Battery-protection features include: low-voltage prequalification, charge fault timer, die temperature monitoring,
and battery temperature monitoring. The battery
temperature monitoring adjusts the charge current and
termination voltage for safe use of secondary lithium-ion
batteries.
The IC accepts either a general DC input or USB.
It has programmable automatic input-current limiting to protect upstream charging sources such as USB.
Charge parameters are easily adjustable through an I2C
interface. Charge is terminated based on user-selectable
minimum current level. A safety timer with reset control
provides a safety backup for I2C interface. Charge status
is provided to the application processor through an interrupt pin.
The IC is available in a space-saving, 20-bump, 2.18mm
x 1.62mm WLP package.
SSwitch-Mode Charger
High-Efficiency
Low Heat
Fast Charge Time
SSmall and Simple
SPrecise
Up to Q5% Current Regulation and 0.5% Voltage
Regulation
SSafe
JEITA Battery Temperature Monitor
Over/Undervoltage Protection, Safety Timers,
Temperature Regulation
USB Friendly
SFlexible
Programmable Voltage/Current
Status/Interrupts Through I2C
Automatic Input Current Limit
SI2C Interface
Input Current Limit (100mA to 1500mA)
Fast-Charge / Termination Current (250mA to
1550mA)
Charge Voltage (4.1V, 4.15V, 4.2V, 4.35V)
Safety Timer
Termination Enable
S +22V Absolute Maximum Input Voltage Rating
S Up to 7.5V Maximum Operating Input Voltage
S 5V USB/Safeout LDO for USB PHY
S 2.3A GSM RF Test Mode (Factory Testing)
S Charge Current to Voltage Conversion (VICHG) for
Baseband ADC
S Reverse Battery Leakage Protection
S Input /Output Overvoltage Protection
S Interrupt Status Output
Applications
USB Charging
Headsets and Media Players
Smartphones
Digital Cameras
GPS, PDAs
Ordering Information appears at end of data sheet.
For related parts and recommended products to use with this part,
refer to www.maxim-ic.com/MAX8971.related.
Simplified Applications Circuit appears at end of data sheet.
����������������������������������������������������������������� Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
TABLE OF CONTENTS
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Package Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Typical Operating Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Typical Operating Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Typical Operating Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Typical Operating Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Bump Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Bump Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Detailed Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DC Input—Fast-Hysteretic
Step-Down Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Soft-Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
PVL and AVL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Thermistor Input (THM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Thermal Foldback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Charger States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Charger-Disabled State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Dead-Battery State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Dead-Battery + Prequalification State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Prequalification State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Fast-Charge Constant-Current State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Fast-Charge Constant Voltage State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Top-Off State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Done State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Timer Fault State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Overvoltage and Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Automatic Input Current
Limit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
VICHG Charging Current Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SAFEOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
JEITA Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Maxim Model Gauge M3 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Factory-Mode GSM Test Mode Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Applications Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Inductor Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Input Capacitor Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
����������������������������������������������������������������� Maxim Integrated Products 2
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
TABLE OF CONTENTS (continued)
Output Capacitor Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Charge Current Resistor Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
I2C Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Charger Interrupt Requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Charger Interrupt Masks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Charger Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
DETAILS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DETAILS2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
USB Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Input Voltage Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Fast-Charge Current and Timer Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Input-Current Limit and Charger Restart Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Done Current, Timer, GSM Test Mode, and Battery Regulation Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Temperature Regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Charger Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Simplified Applications Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Chip Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
LIST OF TABLES
Table 1. Trip Temperatures for Different Thermistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 2. Suggested Inductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 3. Charge Current Settings for 47mΩ and 68mΩ Sense Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 4. Topoff Current Settings for 47mΩ and 68mΩ Sense Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 5. High-Level I2C Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 6. CHGCC[4:0] Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 7. DCILMT[5:0] Bit Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
LIST OF FIGURES
Figure 1. Typical Application Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 2. Li/Li-Poly Charge Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 3. Functional State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 4. JEITA Safety Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 5. MAX8971 with MAX17047 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
����������������������������������������������������������������� Maxim Integrated Products 3
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
ABSOLUTE MAXIMUM RATINGS
BYP to PG_ ............................................................-0.3V to +22V
DC_ to BYP .............................................................-6V to +0.3V
I2CIN, VICHG, IRQB, SDA, SCL to GND..................-0.3V to +6V
BST to AVL.............................................................-0.3V to +16V
BST to LX_................................................................-0.3V to +6V
PVL, SFO, BAT, CS to PG_......................................-0.3V to +6V
AVL, THM to GND....................................................-0.3V to +6V
PG_ to GND...........................................................-0.3V to +0.3V
DC_, LX_, CS, BAT, BYP Continuous Current .............. 1.6ARMS
Continuous Power Dissipation (TA = +70NC)
WLP derate 21.7mW/NC above +70NC ......................1736mW
Operating Temperature Range........................... -40NC to +85NC
Junction Temperature......................................................+150NC
Storage Temperature Range............................. -65NC to +150NC
Soldering Temperature (reflow).......................................+260NC
*This device is constructed using a unique set of packaging techniques that impose a limit on the thermal profile the device can be
exposed to during board-level solder attach and rework. This limit permits only the use of the solder profiles recommended in the
industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR / VPR and Convection reflow. Preheating is required.
Hand or wave soldering is not allowed.
PACKAGE THERMAL CHARACTERISTICS (Note 1)
WLP
Junction-to-Ambient Thermal Resistance (qJA)...........46°C/W
Junction-to-Case Thermal Resistance (qJC)..................2°C/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDC = 5V, CBYP = 1FF, IFCHG = 500mA, CAVL = 4.7FF, VTHM = AVL/2, TA = -40NC to +85NC, unless otherwise noted. Typical values
are at TA = +25NC.) (Note 2)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VOVP
V
DC INPUT
DC Operating Voltage Range
DC Undervoltage Lockout
4.0
DC rising, 500mV hysteresis
3.6
3.8
4.0
V
DC Overvoltage Threshold (VOVP)* DC rising, 250mV hysteresis
7.25
7.5
7.75
V
100
mV
DC OVP Interrupt Delay
DC to BAT Shutdown Threshold
DC Supply Current
BST Leakage Current
16
When charging stops, VDC falling, 150mV hysteresis
Charger enabled, VDC = 5.5V
VBST = 5.5V, LX_ = PG_
LX_ Leakage Current
VLX_ = 0 or 5.5V
BAT Reverse Leakage Current
VDC = 0V, VBAT = 4.2V
Input-Current Limit Range
0
50
ms
2
0.01
TA = +25°C
mA
10
0.1
TA = -40°C to +85°C
0.01
TA = +25°C
10
FA
0.1
TA = -40°C to +85°C
1
0.1
5
FA
1.5
A
����������������������������������������������������������������� Maxim Integrated Products 4
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
ELECTRICAL CHARACTERISTICS (continued)
(VDC = 5V, CBYP = 1FF, IFCHG = 500mA, CAVL = 4.7FF, VTHM = AVL/2, TA = -40NC to +85NC, unless otherwise noted. Typical values
are at TA = +25NC.) (Note 2)
PARAMETER
Input-Current Limit Accuracy
CONDITIONS
MIN
TYP
MAX
USB 100mA mode
90
95
100
USB 500mA mode
450
475
500
Input limit programmed to 1.5A, IFCHG = 1500mA
1350
1500
1650
Adaptive Input-Current Limit (AICL) DC voltage where charge current is regulated
(Note 4)
DC voltage where charge current is set to 75mA
4.5
Input Limit Switch
35
mA
V
4.4
VDC = 5.5V, IBYP = 100mA
UNITS
80
mI
BUCK OPERATION
Switching Frequency
VBAT = 3.6V
4
MHz
99.5
%
Minimum On-Time
55
ns
Maximum On-Time
10
µs
Minimum Off-Time
65
ns
Maximum Duty Cycle
Soft-Start Time
1.5
High-Side Resistance
Low-Side Resistance
Thermal Regulation Temperature
(TREG)
Thermal Regulation Gain
ILX = 100mA, VDC = 5.5V
ILX = 100mA, VDC = 5.5V
I2C programmable 2-bits (90, 105, 120, and disable
selections, 105 default)
Percentage decrease in IFCHG above the thermal
regulation temperature
ms
120
250
mI
150
220
mI
105
°C
5
%/°C
BATTERY CHARGER PRECHARGE
Battery-Prequalification Lower
Threshold (VPQLTH)
VBAT rising, 130mV hysteresis
2.1
V
Dead-Battery Charge Current
(IDBAT)
0V ≤ VBAT ≤ 2.1V
45
mA
Battery-Prequalification Upper
Threshold (VPQUTH)**
VBAT rising, 150mV hysteresis
2.5
V
Prequalification Charge Current
(IPQ)
Percentage of fast-charge current programmed
10
%
CONSTANT-CURRENT MODE
BAT Fast-Charge Current Range
(IFC)
Fast-Charge Current Accuracy
250
1550
mA
TA = +15NC to +45NC
-5
+5
%
JEITA safety region (Figure 6)
-65
-35
%
5 bits–50mA steps, RCS = 47mI
-50
����������������������������������������������������������������� Maxim Integrated Products 5
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
ELECTRICAL CHARACTERISTICS (continued)
(VDC = 5V, CBYP = 1FF, IFCHG = 500mA, CAVL = 4.7FF, VTHM = AVL/2, TA = -40NC to +85NC, unless otherwise noted. Typical values
are at TA = +25NC.) (Note 2)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
CONSTANT VOLTAGE MODE
-0.5
+0.5
TA = -40NC to +85NC
-1
+1
JEITA safety region,
percentage of battery
regulation voltage
(Note 6)
96
97
98
TA = +25NC
Battery Regulation Voltage
(VBATREG)
IBAT = 100mA, operating in
voltage-regulation mode, I2Cprogrammable 4.1V, 4.15V,
4.2V, and 4.35V selection
Battery Refresh Threshold
(Below regulation point), 100mV and 150mV selection,
default 150mV (Note 5)
120
150
185
VBAT threshold over regulation voltage to turn off
charger during charge (% of regulation voltage)
(Note 7)
102
103.5
105
Battery Overvoltage Protection
%
Hysteresis (VBAT falling) at 4.2V
Charge-Current Termination
Threshold (ITOPOFF)
Charge-Current Termination
Accuracy
Programmable topoff current independent of JEITA
functionality, default 50mA, 200mA hysteresis
%
1.4
50
Deglitch time
ITOPOFF = 200mA
mV
200
16
-20
mA
ms
+20
%
GSM TEST MODE
GSM Test-Mode Output Pulse
Current
VBAT capacitance ≥ 60FF, peak current pulse
frequency = 217Hz, on-duty cycle 12.5%
GSM Test-Mode Minimum Output
VBAT capacitance ≥ 60FF, current pulse
frequency = 217Hz, on-duty cycle 12.5%
(Note 3)
2.3
A
3.7
V
CHARGER TIMER
Prequalification Time (tPQ)
VBAT < VBATPQ_UT
45
Mins
Fast-Charge Time (tFC)
Default 5 hours, I2C programmable (4–10 hours and
disabled selection)
5
hrs
20
%
Timer Accuracy
Top-Off Time (tTOPOFF)
I2C programmable 0 to 70 mintues, 10-minute steps,
default 30 mintues
Top-Off Timer Accuracy
Timer-Extend Current Threshold
(Note 3)
Percentage of fast-charge current below which the
timer clock operates at half speed
0
70
Mins
20
%
50
%
����������������������������������������������������������������� Maxim Integrated Products 6
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
ELECTRICAL CHARACTERISTICS (continued)
(VDC = 5V, CBYP = 1FF, IFCHG = 500mA, CAVL = 4.7FF, VTHM = AVL/2, TA = -40NC to +85NC, unless otherwise noted. Typical values
are at TA = +25NC.) (Note 2)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
THERMISTOR MONITOR
THM Threshold, Cold, No Charge
(0°C)
VTHM/AVL rising, 1% hysterisis
(thermistor temperature falling)
71.06
74.56
78.06
%
THM Threshold, Cold, Current
Foldback (+15°C)
VTHM/AVL rising, 1% hysterisis
(thermistor temperature falling)
57.00
60.00
63.00
%
THM Threshold, Hot, Voltage
Foldback (+45°C)
VTHM/AVL falling, 1% hysterisis
(thermistor temperature rising)
32.68
34.68
36.68
%
THM Threshold, Hot, No Charge
(+60NC)
VTHM/AVL falling, 1% hysterisis
(thermistor temperature rising)
21.24
22.54
23.84
%
THM Input Bias Current
VTHM = VAVL or 0V
-0.2
0.01
+0.2
TA = +25NC
0.01
TA = +85NC
FA
VICHG
IBAT = 100mA
VICHG Output Voltage
150
IBAT = 1000mA
1260
IBAT = 1500mA
1400
mV
1540
2100
mV
mV
IRQB OUTPUT
Low-Level Output Saturation
Voltage
IIRQB =10mA, sinking current
High-Level Leakage Current
VIRQB = 5V
TA = +25NC
-1
0.01
0.4
V
+1
FA
0.1
TA = +85NC
FA
SAFEOUT OUTPUT
Regulated Output
ISFO = 30mA, VDC = 5.5V
Dropout Voltage
ISFO = 30mA
4.75
Current Limit
Maximum Output Current
5
5.25
mV
590
mA
100
POK Output Threshold
V
45
mA
2.7
V
5.05
V
5.05
V
PVL/AVL OUTPUT
PVL Output Voltage
AVL Output Voltage
5.5V < VDC < 7.5V, no load
5.5V < VDC < 7.5V, no load
LOGIC LEVELS AND TIMING CHARACTERISTICS (SCL, SDA)
Output Low Threshold
Io = 3mA, sink current (SDA)
Input Low Threshold
VI2CIN = 1.8V
Input High Threshold
VI2CIN = 1.8V
1.4
0.4
V
0.4
V
V
����������������������������������������������������������������� Maxim Integrated Products 7
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
ELECTRICAL CHARACTERISTICS (continued)
(VDC = 5V, CBYP = 1FF, IFCHG = 500mA, CAVL = 4.7FF, VTHM = AVL/2, TA = -40NC to +85NC, unless otherwise noted. Typical values
are at TA = +25NC.) (Note 2)
PARAMETER
Input Bias Current
CONDITIONS
MIN
TYP
VI2CIN = 1.8V, TA = +25°C
MAX
UNITS
1
µA
400
kHz
SCL Clock Frequency
100
Bus Free Time Between START
and STOP (Note 3)
1.3
µs
Hold Time REPEATED START
Condition (Note 3)
0.6
µs
SCL Low Period (Note 3)
1.3
µs
SCL High Period (Note 3)
0.6
µs
Setup Time REPEATED START
Condition (Note 3)
0.6
µs
SDA Hold Time (Note 3)
0
µs
SDA Setup Time (Note 3)
100
ns
Maximum Pulse Width of Spikes
(must be suppressed by the input
filter of both SDA and SCL signals)
(Note 3)
Setup Time for STOP Condition
(Note 3)
50
0.6
ns
µs
THERMAL REGULATION AND SHUTDOWN
Thermal Shutdown Temperature
(Note 3)
Thermal Shutdown Hysteresis
(Note 3)
+160
°C
15
°C
Note 2: Parameters are production tested at TA = +25NC. Limits over the operating temperature range are guaranteed through
correlation using statistical quality control (SQC) methods.
Note 3: Guaranteed by design, not production tested.
Note 4: Voltage for 4.35V battery mode increases by 100mV.
Note 5: Refresh voltage for 4.15V increases by 50mV.
Note 6: JEITA decreases by 1% for 4.15V termination voltage.
Note 7: Battery overvoltage increases by 1% for 4.15V termination voltage.
* = Contact factory for alternate thresholds (6.7V, 9.7V, and 14V available).
** = Contact the factory for 3.0V.
����������������������������������������������������������������� Maxim Integrated Products 8
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Typical Operating Characteristics
(VDC = 5V, CBYP = 1FF, CAVL = 4.7FF, VTHM = 2.5V, TA = -40NC to +85NC, unless otherwise noted. Typical values are at TA = +25NC.)
DC SUPPLY CURRENT
vs. TEMPERATURE
DC QUIESCENT CURRENT
vs. DC SUPPLY VOLTAGE
DC SUPPLY CURRENT (mA)
2.0
1.5
1.0
2.0
1.5
1.0
0.5
0.5
0
6
8
10
12
0
14
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90
DC VOLTAGE (V)
TEMPERATURE (°C)
BATTERY LEAKAGE CURRENT
vs. TEMPERATURE
FAST-CHARGE CURRENT
vs. DC SUPPLY VOLTAGE
600
1.6
1.4
FAST-CHARGE CURRENT (mA)
MAX8971 toc03
1.8
1.2
1.0
0.8
0.6
0.4
MAX8971 toc04
4
BATTERY LEAKAGE CURRENT (µA)
MAX8971 toc02
2.5
QUIESCENT CURRENT (mA)
2.5
MAX8971 toc01
3.0
500
400
300
200
VDC, FALLING
100
0.2
0
0
VDC, RISING
IFCHG = 500mA
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90
3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5
TEMPERATURE (°C)
DC VOLTAGE (V)
MEDIUM LOAD SWITCHING WAVEFROMS
HEAVY LOAD SWITCHING WAVEFROMS
MAX8971 toc06
MAX8971 toc07
20mV/div
AC-COUPLED
2V/div
VBAT
VLX
20mV/div
AC-COUPLED
VBAT
VLX
2V/div
0
ILX
0
200mA/div
ILX
IFCHG = 500mA
1A/div
IFCHG = 1.55A
200ns/div
400ns/div
����������������������������������������������������������������� Maxim Integrated Products 9
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Typical Operating Characteristics (continued)
(VDC = 5V, CBYP = 1FF, CAVL = 4.7FF, VTHM = 2.5V, TA = -40NC to +85NC, unless otherwise noted. Typical values are at TA = +25NC.)
AVL/PVL VOLTAGE
vs. DC SUPPLY VOLTAGE
CHARGER ENABLE SOFT-START TIME
5.1
500mA/div
IBAT
500mA/div
IDC
0
VDC
2V/div
2V/div
VBAT
5.0
AVL/PVL VOLTAGE (V)
0
MAX8971 toc09
5.2
MAX8971 toc08
4.9
VPVL
4.8
VAVL
4.7
4.6
4.5
0
4.4
4.3
4.0
400µs /div
4.5
5.0
5.5
6.0
6.5
7.0
7.5
DC VOLTAGE (V)
DC PLUG-IN TO 1A
DEFAULT FAST-CHARGE CURRENT
USB INSERTION INTO 500mA
DEFAULT FAST-CHARGE CURRENT
MAX8971 toc10
MAX8971 toc10a
500mA/div
5V/div
VUSB
VBAT
WITH AUTOMATIC
USB 100MA MODE
VLX
0
2V/div
IBAT
0
5V/div
0
IDC
0
500mA/div
WITH AUTOMATIC
USB 100mA MODE
0
2V/div
VBAT
2V/div
250mA/div
VDC
IBAT
0
0
IFCHG = 1.A
100ms /div
40ms/div
USB REMOVAL
BATTERY INSERTION/REMOVAL
(1A INPUT CURRENT LIMIT)
MAX8971 toc11
MAX8971 toc12
5V/div
VUSB
VBAT
0
2V/div
VLX
0
5V/div
VDC
VBAT
2V/div
2V/div
VLX
0
5V/div
0
LG LP-AHKM (950mAh)
ILIM = 1A
IFCHG = 500mA
0
IBAT
500mA/div
IBAT
100ms /div
500mA/div
0
10ms/div
���������������������������������������������������������������� Maxim Integrated Products 10
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Typical Operating Characteristics
(VDC = 5V, CBYP = 1FF, CAVL = 4.7FF, VTHM = 2.5V, TA = -40NC to +85NC, unless otherwise noted. Typical values are at TA = +25NC.)
FAST-CHARGE CURRENT
vs. TEMPERATURE
520
510
500
490
480
470
MAX8971 toc14
530
FAST-CHARGE CURRENT (mA)
540
FAST-CHARGE CURRENT (mA)
600
MAX8971 toc13
550
FAST-CHARGE CURRENT
vs. BATTERY VOLTAGE
500
400
300
200
100
460
0
450
0.5
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90
1.0
1.5
2.0
2.5
3.0
3.5
TEMPERATURE (°C)
BATTERY VOLTAGE (V)
FAST CHARGE TO SUSPEND
BATTERY REGULATION VOLTAGE
vs. TEMPERATURE
MAX8971 toc15
VLX
5V/div
0
ILX
200mA/div
4.220
MAX8971 toc16
VSDA
5V/div
0
5V/div
4.215
BATTERY VOLTAGE (V)
VBAT
4.0
4.210
4.205
4.200
4.195
0
4.190
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90
400ms/div
TEMPERATURE (°C)
BATTERY CHARGER EFFICIENCY
vs. BATTERY VOLTAGE
IBAT = 0.5A
90
90
85
80
75
IBAT = 1.25A
IBAT = 1.5A
70
65
85
VBAT = 3.6V
80
VBAT = 3V
75
70
65
60
55
VBAT = 4.2V
95
EFFICIENCY (%)
EFFICIENCY (%)
100
MAX8971 toc18
95
MAX8971 toc17
100
BATTERY CHARGER EFFICIENCY
vs. CHARGE CURRENT
60
VDC = 5V, PREQ = 2.5V, VBAT = 4.2V
50
2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3
BATTERY VOLTAGE (V)
55
50
0
200
400
600
800 1000 1200 1400
CHARGE CURRENT (mA)
���������������������������������������������������������������� Maxim Integrated Products 11
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Typical Operating Characteristics
(VDC = 5V, CBYP = 1FF, CAVL = 4.7FF, VTHM = 2.5V, TA = -40NC to +85NC, unless otherwise noted. Typical values are at TA = +25NC.)
CHARGE PROFILE FOR 1830mAh
4.35V BATTERY CHARGED AT 0.55C
BATTERY CHARGER EFFICIENCY
vs. BATTERY VOLTAGE
90
BATTERY VOLTAGE (V)
EFFICIENCY (%)
80
70
60
50
ICHG = 500mA, PREQ = 2.5V
40
30
900
3.5
800
600
2.5
500
2.0
400
1.5
10
0.5
IBAT = 0.5A
700
3.0
1.0
0
300
200
100
0
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
0
30
CHARGE PROFILE FOR 1500mAh
4.2V BATTERY WITH 70mA
CONSTANT LOAD CHARGED AT 0.6C
BATTERY VOLTAGE (V)
60
90
120
150
TIME (MINUTES)
BATTERY VOLTAGE (V)
MAX8971 toc21
4.5
1000
4.0
20
IBAT = 0.5A
MAX8971 toc20
4.5
MAX8971 toc19
100
AUTOMATIC INPUT CURRENT LIMIT
4.0
800
3.5
700
600
3.0
500
2.5
400
2.0
1.5
500mA/div
500mA/div
IBAT
VDC
200
VBAT
100
0.5
0
0
IDC
300
1.0
0
MAX8971 toc22
900
0
2V/div
2V/div
0
-100
0
30
60
90
120
150
180
10ms /div
TIME (MINUTES)
AUTOMATIC INPUT CURRENT LIMIT
(2I CABLE RESISTANCE)
AUTOMATIC INPUT CURRENT LIMIT
(1I CABLE RESISTANCE)
MAX8971 toc23
MAX8971 toc24
500mA/div
IBAT
0
500mA/div
200mA/div
IBAT
0
500mA/div
IDC
0
VBAT
2V/div
VDC
0
2V/div
0
100ms /div
0
IDC
2V/div
0
2V/div
0
VBAT
VDC
4ms/div
���������������������������������������������������������������� Maxim Integrated Products 12
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Typical Operating Characteristics
(VDC = 5V, CBYP = 1FF, CAVL = 4.7FF, VTHM = 2.5V, TA = -40NC to +85NC, unless otherwise noted. Typical values are at TA = +25NC.)
SFO OUTPUT VOLTAGE
vs. INPUT VOLTAGE
SFO OUTPUT VOLTAGE
vs. LOAD CURRENT
5.00
IFSO = 100mA
4.95
5.05
SFO VOLTAGE (V)
IFSO = 50mA
4.90
MAX8971 toc26
5.05
SFO OUTPUT VOLTAGE (V)
5.10
MAX8971 toc25
5.10
5.00
VDC = 7V
4.95
4.90
4.85
4.85
4.80
4.80
VDC = 5V
IFCHG = 500mA
4.75
4.75
5.5
6.0
6.5
7.0
30 40 50 60 70 80 90 100
LOAD CURRENT (mA)
VICHG GAIN vs. CHARGE CURRENT
CHARGE CURRENT
vs. AMBIENT TEMPERATURE
600
MAX8971 toc27
500
CHARGE CURRENT (mA)
1.7
VICHG GAIN (V/V)
10 20
INPUT VOLTAGE (V)
1.8
1.6
1.5
1.4
1.3
400
300
200
100kI, β = 4250 THERMISTOR
IFCHG = 500mA, SAFETY REGION 1
100
0
1.2
100
300
500
700
900 1100 1300 1500
0
5
10
15
20
25
CHARGE CURRENT (mA)
FALLING AMBIENT TEMPERATURE (°C)
CHARGE CURRENT
vs. AMBIENT TEMPERATURE
GSM TEST MODE
30
100kI, β = 4250 THERMISTOR
IFCHG = 500mA, SAFETY REGION 1
600
MAX8971 toc29
MAX8971 toc30
700
CHARGE CURRENT (mA)
0
7.5
MAX8971 toc28
5.0
500
IBATT
400
300
200
VBATT
100
VDC
0
40
45
50
55
60
65
2ms/div
RISING AMBIENT TEMPERATURE (°C)
���������������������������������������������������������������� Maxim Integrated Products 13
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Bump Configuration
TOP VIEW
(BUMP SIDE DOWN)
+
A
B
C
D
MAX8971
1
2
3
4
5
PG1
PG2
VICHG
CS
BAT
A1
A2
A3
A4
A5
LX1
LX2
IRQB
I2CIN
THM
B1
B2
B3
B4
B5
BYP
BST
GND
SCL
SDA
C1
C2
C3
C4
C5
DC1
DC2
PVL
SFO
AVL
D1
D2
D3
D4
D5
WLP
Bump Description
PIN
NAME
FUNCTION
A1, A2
PG1, PG2
A3
VICHG
A4
CS
Current-Sense Input Power Pin
A5
BAT
Battery Connection. Connect to a single-cell Li+ battery.
B1, B2
LX1, LX2
Power Ground for Step-Down Low-Side FET
Battery-Charging Current Monitor Output. This pin is an analog representation of the charger current
at 1.4mV/mA.
Buck Inductor Connection. Connect the inductor between LX_ and CS. The LX1 and LX2 pins must
be connected together externally.
B3
IRQB
Open-Drain Host Processor Interrupt Pin
B4
I2CIN
I2C Interface Supply
B5
THM
Thermistor Input. Connect a negative temperature coefficient (NTC) thermistor from THM to GND.
Connect a resistor equal to the thermistor +25°C resistance from THM to AVL. Charging is
suspended when the thermistor is outside the hot and cold limits. Connect THM to GND to disable
the thermistor temperature sensor. If the thermistor function is disable through I2C, connect THM to
GND.
C1
BYP
Connection Point Between Reverse Blocking MOSFET and High-Side Switching MOSFET. Bypass to
PG_ with a minimum 1FF ceramic capacitor.
C2
BST
High-Side FET Driver Supply. Bypass BST to LX with a 0.1FF ceramic capacitor.
C3
GND
Analog Ground. GND is the low-noise ground connection for the internal circuitry.
���������������������������������������������������������������� Maxim Integrated Products 14
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Bump Description (continued)
PIN
NAME
C4
SCL
I2C Interface Clock. Connect a 10kI resistor from SCL to I2CIN.
FUNCTION
C5
SDA
I2C interface Data. Connect a 10kI resistor from SDA to I2CIN.
D1, D2
DC1, DC2
High-Current Charger Input Supply Pin(s). Bypass to PG_ with a 2.2FF ceramic capacitor. DC is
capable of delivering up to 1.5A to BYP. DC supports both AC adapter and USB inputs. Short DC1
and DC2 together externally.
D3
PVL
Internal Bias Regulator High-Current Output Bypass Pin. Supports internal noisy and high-current
gate drive loads. Bypass to PGND with a minimum 1FF ceramic capacitor. Do not use PVL to power
external loads.
D4
SFO
5V Regulated LDO Output. Bypass SFO to GND with a 1FF or larger ceramic capacitor. SFO can be
used to supply low-voltage rated USB systems.
D5
AVL
Internal-Bias-Regulator Quiet Analog Bypass Pin. Internal 10I connection between PVL and AVL
forms a lowpass filter with external bypass capacitor to GND. Do not use AVL to power
external loads.
-0.3V TO +22V
TOLERANT
4.0V TO 10V OPERATIONAL
DC
C7
4.7µF
6.3V
0402
DC1,
DC2
C1
2.2µF
25V
0603
BYP
BST
C6
0.1µF
0402
BYP
SFO
C3
1µF
6.3V
0402
C4
4.7µF
6.3V
0402
AVL
GND
L1, 1µH
2520
LX1,
LX2
PVL
C2
1µF
25V
0603
MAX8971
PG1,
PG2
CS
VICHG
R1, 47mI
0402
I2CIN
BAT+
BAT
C5
2.2µF
6.3V
0603
IRQB
µP
BATSYSTEM
LOAD
THM
RTB
0402
SDA
SCL
R2,
100kI
AVL
Figure 1. Typical Application Circuit
���������������������������������������������������������������� Maxim Integrated Products 15
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Detailed Description
The MAX8971 is a JEITA-compliant Li+ switching
battery charger that safely charges a single Li+ cell
in accordance with JEITA specifications. The IC
accepts an input supply range from 4V to 7.5V, but
disables charging if the supply voltage exceeds +7.5V,
protecting against unqualified or faulty AC adapters.
The step-down converter supplies up to 1.5A to the battery. The IC includes charger features thermistor monitor,
charger status and fault outputs. Also included are interrupt
signals to the processor. Flexibility is maintained with
adjustable charge current, input current limit, and a
minimum battery voltage (when charging is scaled back
to hold the battery voltage up) through an I2C interface.
DC Input—Fast-Hysteretic
Step-Down Regulator
If a valid DC input is present, battery charging is
supplied by the high-frequency step-down regulator from
DC. The step-down regulation point is then controlled
by three feedback signals: maximum step-down output
current programmed by the input current limit, maximum charger current programmed for the fast-charge
current, and maximum die temperature. The feedback
signal requiring the smallest current controls the average
output current in the inductor. This scheme minimizes
total power dissipation for battery charging, and allows
the battery to absorb any load transients with minimum
voltage disturbance.
A proprietary hysteretic current PWM control scheme
ensures fast switching and physically tiny external
components. The feedback control signal that requires
the smallest input current, controls the center of the peak
and valley currents in the inductor. The ripple current
is internally set to provide 4MHz operation. When the
input voltage decreases near the output voltage, very
high duty cycle occurs. Due to minimum off-time, 4MHz
operation is not achievable. The controller then provides
minimum off-time, peak current regulation. Similarly,
when the input voltage is too high to allow 4MHz operation due to the minimum off-time, the controller becomes
a minimum on-time, valley current regulator. In this
way, ripple current in the inductor is always as small as
possible to reduce ripple voltage-on battery for a given
capacitance. The ripple current is made to vary with
input voltage and output voltage in a way that reduces
frequency variation. However, the frequency still varies
somewhat with operating conditions.
Soft-Start
To prevent input current transients, the rate of change
of the input current (di/dt) and charge current is
limited. When the input is valid the charge current ramps
from 0mA to the fast-charge current value in 1.5ms.
Charge current also soft-starts when transitioning from
the prequalification state to the fast-charge state. There
is no di/dt limiting when transitioning from the done state
to the fast-charge state.
PVL and AVL
PVL is a 5V linear regulator that the IC uses to power the
gate drivers for its step-down charger. PVL also charges
the BST capacitor. The PVL linear regulator is on when
DC is greater than ~2.5V, otherwise it is off. Bypass PVL
with a 1FF ceramic capacitor to PG. Powering external
loads from PVL is not recommended.
As shown in Figure 1, AVL is a filtered output from the
PVL linear regulator that the IC uses to power
its internal analog circuits. The filter consists of an
internal 10I resistor, and the AVL external bypass
capacitor (4.7FF). This filter creates a 100kHz lowpass filter that cleans the 4MHz switching noise from the analog
portion of the IC. Connect a 4.7FF ceramic capacitor
from AVL to GND. Powering external loads with AVL is
not recommended.
Thermistor Input (THM)
The THM input connects to an external negative
temperature coefficient (NTC) thermistor to monitor
battery or system temperature. Charging is suspended
when the thermistor temperature is out of range. The
charge timers are suspended and hold their state, but no
fault is indicated. When the thermistor comes back into
range, charging resumes and the charge timer continues
from where it left.
Since the thermistor monitoring circuit employs an
external bias resistor from THM to AVL, the thermistor
is not limited only to 10kI (at +25NC). Any resistance
thermistor can be used as long as the value is equivalent
to the thermistors +25NC resistance. For example, with a
���������������������������������������������������������������� Maxim Integrated Products 16
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
10kI at RTB resistor, the charger enters a temperature
suspend state when the thermistor resistance falls below
3.97kI (too hot) or rises above 28.7kI (too cold). This
corresponds to the 0NC to +50NC range when using a
10kI NTC thermistor with a beta of 3500. The general
relation of thermistor resistance to temperature is defined
by the following equation:
Note that since AVL is active whenever valid input power
is connected at DC, thermistor bias current flows at all
times. Using a 10kI thermistor and a 10kI pullup to
AVL, results in an additional 250FA load. This load can
be reduced to 25FA by instead using a 100kI thermistor
and 100kI pullup resistor.
RT = R25 x e{A((1/(T+273)) x (1/298))}
Thermal foldback maximizes the battery charge current
while regulating the IC's junction temperature. When
the die temperature exceeds TREG, a thermal limiting
circuit reduces the battery charge-current target until the
charge current reaches 10% of the fast-charge current
setting. The charger maintains 10% of the fast-charge
current until the die temperature reaches TSHDN. Please
note that the IC is rated for a maximum ambient temperature of +85NC. Furthermore, although the maximum
die temperature of the MAX8971 is +150NC, it is common
industry practice to design systems in such a way that
the die temperature never exceeds +125NC. Limiting the
maximum die temperature to +125NC extends long-term
reliability.
Thermal Foldback
where:
RT = the resistance in I of the thermistor at temperature T in celsius
R25= the resistance in I of the thermistor at +25NC
A = the material constant of the thermistor, which typically ranges from 3000k to 5000k
T = the temperature of the thermistor in NC
Some designs might prefer other thermistor temperature
limits. Threshold adjustment can be accommodated by
changing RTB, connecting a resistor in series and/or in
parallel with the thermistor, or using a thermistor with
different A. For example, a +45NC hot threshold and 0NC
cold threshold can be realized by using a thermistor with
a A to 4250, and connecting 120kI in parallel. Since the
thermistor resistance near 0NC is much higher than it is
near +50NC, a large parallel resistance lowers the cold
threshold, while only slightly lowering the hot threshold.
Conversely, a small series resistance raises the cold
threshold, while only slightly raising the hot threshold.
Raising RTB, lowers both the hot and cold threshold,
while lowering RTB raises both thresholds.
Charger States
The IC utilizes several charging states to safely and
quickly charge batteries as shown in Figure 3.
Figure 2 shows an exaggerated view of a Li+/Li-Poly
battery progressing through the following charge states
when the die and battery are close to room temperature:
dead battery ➝ prequalification ➝ fast charge ➝ top-off
➝ done.
Table 1. Trip Temperatures for Different Thermistors
THERMISTOR
TEMPERATURE
RTHM at TA=+25°C
Thermistor Beta (AI)
10,000
10,000
10,000
47,000
47,000
100,000
100,000
3380
3940
3940
4050
4050
4250
4250
RTB (I)
10,000
10,000
10,000
47,000
47,000
100,000
100,000
RTP (I)
Open
Open
301,000
Open
1,200,000
Open
1,800,000
RTS (I)
Short
Short
499
Short
2,400
Short
6,800
Resistance at T1_n15
(I)
61,788
61,788
77,248
290,410
380,716
617,913
934,027
Resistance at T1_0(I)
29,308
29,308
31,971
137,750
153,211
293,090
343,283
���������������������������������������������������������������� Maxim Integrated Products 17
BATTERY VOLTAGE
DONE
TOP-OFF
FAST-CHARGE
(CONSTANT VOLTAGE)
FAST-CHARGE
(CONSTANT CURRENT)
PREQUALIFICATION
DEAD BATTERY +
PREQUALIFICATION
DEAD
BATTERY
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
VBATREG
VPLTH
VDBAT
VPLTH
BATTERY CHARGE CURRENT
TIME
IFCHG
IPQ + IDBAT
IPQ
IDBAT
0
TIME
Figure 2. Li/Li-Poly Charge Profile
���������������������������������������������������������������� Maxim Integrated Products 18
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
NO PWR
CHARGER DISABLED
VDC > VUVLO
AND VDC > VBAT
AND TJ < TSHDN
VIN TOO HIGH
IRBQ = LOW
IBAT = 0
VDC < VOVLO
TIMER = RESUME
VDC > VOVLO
TIMER = SUSPEND
DEAD BAT
IRBQ = LOW
CHECK
CHGINT,
CHGSTAT, AND DETAILS
REGISTER
IBAT = IDBAT
VBAT >
VPQLTH
ANY CHARGING
STATE DEAD BAT,
PREQUAL, FAST
CHARGE OR TOPOFF
THERMISTOR < T1
TIMER = SUSPEND
THERMISTOR > T1
TIMER = RESUME
BATTERY COLD
IRBQ = LOW,
IBAT = 0, IF
VBAT > VDBAT
DEADBAT+ PREQUAL
CHECK
CHG_DTLS[3:0]
IBAT = IBAT + IPREQ
VBAT > VDBAT
VBAT < VDBAT
PREQUAL
CHECK
CHG_DTLS[3:0]
IBAT = IPREQ
THERMISTOR < T4
TIMER = RESUME
THERMISTOR > T4
TIMER = SUSPEND
VBAT <
VPQLTH
SET TIMER = 0
BATTERY HOT
IRBQ = LOW,
IBAT = 0, IF
VBAT > VDBAT
VBAT >
VPQUTH
SOFT-START SET
TIMER = 0
TIMER FAULT
IRBQ = LOW
CHECK CHGINT,
CHGSTAT, AND DETAILS
REGISTER
IBAT = 0
TIMER >
TFCHG
FAST CHG
CHECK
CHG_DTLS[3:0]
IBAT = IFC
IBAT < ITOPOFF
BATTERY COOL
IBAT = 50%, *IFCHG
IF VBAT > VDBAT
VBAT <
VPQUTH
TIMER >
TPREQ
IBAT > ITOPOFF + 200mA
SET TIMER = 0
TOPOFF
IRBQ = LOW
CHECK
CHGINT,
CHGSTAT, AND DETAILS
REGISTER
VBAT <
VRESTR
SET TIMER = 0
TIMER >
tTOPOFF
BATTERY WARM
IRBQ = LOW,
VBAT_TERM = VBAT
125mF, IF
VBAT > VDBAT
DONE
IRBQ = LOW
CHECK
CHG_DTLS[3:0]
IBAT = 0
Figure 3. Functional State Diagram
���������������������������������������������������������������� Maxim Integrated Products 19
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Charger-Disabled State
When DC is low or the input voltage is out of range, the IC
disables the charger. To exit this state, the input voltage
must be within its valid range.
Dead-Battery State
When a deeply discharged battery is inserted with a
voltage of less than VPQLTH, the IC disables the switching charger and linearly charges with IDBAT. Once VBAT
increases beyond VPQLTH, the IC clears the prequalification timer, and transitions to the dead battery + prequalification state. This state prevents the IC from dissipating
excessive power in the event of a shorted battery. The
dead-battery linear charge remains on, except when
in the charger disabled state, timer fault state, thermal
shutdown and VBAT > VDBAT.
Dead-Battery + Prequalification State
The dead battery + prequalification state occurs when
the battery voltage is greater than VPQLTH, and less
than VDBAT. In this state, both the linear dead-battery
charger and the switching charger are on, delivering
current to the battery. The total battery current is IDBAT
+ IPQ. If the IC remains in this state for longer than
tPQ, the IC transitions to the timer fault state. A normal
battery typically stays in this state for several minutes
or less. When the battery voltage rises above VDBAT
the IC transitions to the prequalification states. The
dead-battery linear charger remains on except when
in the charger disabled state, timer fault state, thermal
shutdown and VBAT > VDBAT.
Prequalification State
The prequalification state occurs when the battery
voltage is greater than VDBAT and less than VPQUTH.
In this state, the linear dead-battery charger is turned
off. Only the switching charger is on and delivering
current to the battery. The total battery current is IPQ. If
the IC remains in this state for longer than tPQ, then the
IC transitions to the timer fault state. A normal battery
typically stays in the prequalification state for several
minutes or less. When the battery voltage rises above
VPQUTH, the IC transitions to the fast-charge constantcurrent state.
Fast-Charge Constant-Current State
The fast-charge constant-current state occurs when
the battery voltage is greater than VPQUTH and less
than VBATREG. In this state, the switching charger is on
and delivering current to the battery. The total battery
current is IFC. If the IC remains in this state and
the fast-charge constant voltage state for longer than
tFC, then the IC transitions to the timer fault state.
When the battery voltage rises to VBATREG, the IC
transitions to the fast-charge constant voltage state.
The fast-charge constant-current is set to 50% of
programmed value when 0NC < THM <+15NC, and 100%
of programmed value when +15NC < THM <+60NC.
The MAX8971 dissipates the most power in the fastcharge constant-current state. This power dissipation
causes the internal die temperature to rise. If the die
temperature exceeds TREG, IFC is reduced.
If there is low input-voltage headroom (VIN - VBAT), then
IFC decreases due to the impedance from IN to BAT.
Fast-Charge Constant Voltage State
The fast-charge constant voltage state occurs when the
battery voltage is at the VBATREG, and the charge current is greater than ITOPOFF. In this state, the switching
charge is on and delivering current to the battery. The IC
maintains VBATREG and monitors the charge current to
detect when the battery consumes less than the TOPOFF
current. When the charge current decreases below the
TOPOFF threshold, the IC transitions to the top-off state.
If the IC remains in the fast-charge constant-current state
for longer than tFC, then it transitions to the timer fault
state.
Top-Off State
The top-off state occurs when the battery voltage is
at VBATREG and the battery current decreases below
TOPOFF current. In this state, the switching charger is on and delivers current to the battery. The IC
maintains VBATREG for a specified time. When this
time expires, the IC transitions to the DONE state.
If the charging current increases to ITOPOFF + 200mA
before this time expires, then the charge reenters the
fast-charge constant voltage state.
Done State
The IC enters its done state after the charge has been in
the top-off state for tTOPOFF. In this state, the switching
charger is off and no current is delivered to the battery. If
the system load presented to the battery is low << 10FA,
then a typical system can remain in the done state for
many days. If left in the done state long enough, the battery voltage decays below the restart threshold and the
IC transitions back into the fast-charge state. There is no
soft-start (di/dt limiting) during the done-to-fast-charge
state transition.
���������������������������������������������������������������� Maxim Integrated Products 20
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Timer Fault State
The timer fault state occurs when either the prequalification or fast-charge timers expire. In this state, the charger
is off. The charger can exit this timer fault state by cycling
input power.
Overvoltage and Protection
The IC provides for a +22V absolute maximum positive
input voltage, and a -0.3V absolute maximum negative
input voltage. Excursions to the absolute maximum voltage levels should be on a transient basis only, but can
be withstood by the IC indefinitely.
Situations that typically require extended input voltage
ratings include, but are not limited to the following:
U Inductive kick
U Charge source failure
U Power surge
U Improperly wired wall adapter
U Improperly set universal wall adapter
U Wall adapter with the correct plug, but wrong voltage
U Home-built computer with USB wiring harness connected backwards (negative voltage)
U USB connector failure
U Excessive ripple voltage on a switch-mode wall charger
U USB-powered hub that is powered by a wall charger
(typically through a barrel connector) that has any of
the aforementioned issues
U Unregulated charger
Automatic Input Current
Limit Protection
The IC includes an input-current-limiting feature. The
amplifiers required for sensing the currents and associated logic circuitry for making decisions and changing
the battery-charger current are fully integrated in the ICs.
This not only helps in reducing cost, but also improves
the speed of system response.
The IC works by monitoring the current being drawn
from the AC adapter and comparing it to the programmed current limit. The current limit should be set
based on the current-handling capability of the AC
adapter. Generally, this limit is chosen to optimally
fulfill the system-power requirements while achieving
a satisfactory charging time for the batteries. If the
AC-adapter current exceeds its output capability, the
charger responds by cutting back on the charger
current, thereby keeping the current drawn from the AC
adapter within its capability. With such a battery charger,
the AC adapter doesn’t need to be oversized to meet
maximum system and battery-charging requirements
simultaneously, thereby reducing AC adapter cost.
The input current limit has two control inputs, one based
on voltage and one based on current. The voltage input
monitors the input voltage, and when it drops below the
desired input (4.5V), it generates a flag (AICL) to decrement the fast-charge current.
When the voltage comparator initially trips at 4.5V, fastcharge current decrements at a slow rate, allowing the
charger output to settle until the voltage on DC returns
above this voltage threshold. Once the DC voltage
resolves itself, the current delivery of the adapter is maximized. In the event of a limited input current source, an
example being a 500mA adaptor plugged into a 1A input
current limit setting, a second voltage comparator set at
4.4V triggers and throttles the fast-charge current to a
minimum of 75mA. Once the DC voltage corrects itself to
above 4.5V, the fast-charge level is checked every 16ms
to allow the system to recover if the available input power
increases.
The current-limit input monitors the current through the
input FET and generates a flag (DC_I) to decrement the
fast-charge current when the input limit is exceeded. The
fast-charge current is slowly decremented until the inputlimit condition is cleared. At this point, the fast-charge
current is maintained for 16ms and is then sampled
again.
���������������������������������������������������������������� Maxim Integrated Products 21
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
VICHG Charging Current Monitor
VICHG is a buffered output that can be interpreted to the
charge current (VICHG = 1400mV/IFCHG). See the Typical
Operating Characteristics section for the VICHG curve.
The IC JEITA-compliant switching Li+ battery charger
safely charges a single Li+ cell in accordance with JEITA
specifications. The IC monitors the battery temperature
while charging, and automatically adjusts the fast-charge
current and/or charge termination voltage as the battery
temperature varies.
In safety region 1, the IC automatically reduces the
fast-charging current for TBAT < +10NC, and reduces
the charge termination voltage from 4.200V (Q25mV)
to 4.075V (Q25mV) for TBAT > +45NC. The fast-charge
current is reduced to 50% of the nominal fast-charge
current with options for 25% and 75%. JEITA never
specifically states one or the other. When battery charge
current is reduced by 50%, the timer is doubled.
T1
CHARGE TERMINATION VOLTAGE
JEITA Description
SAFETY REGION 2
4.2V
4.1V
4.075V
Figure 5 illustrates how the IC can easily integrate with
Maxim’s Model gauge M3 MAX17047 chip. The user just
needs to add a Schottky diode between VBATT and VTT
on the MAX17047.
0°C
10°C
25°C
45°C
60°C
85°C
60°C
85°C
TEMPERATURE
T2
T1
C
0.5C
0°C
10°C
25°C
45°C
TEMPERATURE
Figure 4. JEITA Safety Region
DC
BATT
MAX8971
Factory-Mode GSM Test Mode Support
The IC supports GSM pulse programming scheme. When
DC is inserted with no battery operation, the IC soft-starts
and cycles through dead-battery, prequalification, and
fast charge, settling at constant voltage-mode operation,
and regulating to the termination voltage (4.2V default).
At this time, when B4 of register 0x08 is sent, the part
can now support GSM pulse. See the Typical Operating
Characteristics section.
Q25mV
4.0V
In safety region 2, the IC automatically reduces the
charge termination voltage from 4.200V (Q25mV) to
4.075V (Q25mV) for TBAT < +10NC and for TBAT > +45NC.
The fast-charge current is not changed in safety region 2.
Maxim Model Gauge M3 Support
T2
Q25mV
FAST-CHARGE CURRENT
SAFEOUT
SAFEOUT is a linear regulator that provides an output
voltage of 5V and can be used to supply low-voltage rated
USB systems. The SFO linear regulator turns on when
VIN > 2.5V.
SAFETY REGION 1
BYP
AVL
LX
PVL
PGND
SFO
MAX17047
THRM
RTD
AIN
THM
VICHG
SDA
SCL
I2CIN
RT
(BATTERY)
BATT
VT T
AGND
VSS
Figure 5. MAX8971 with MAX17047
���������������������������������������������������������������� Maxim Integrated Products 22
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
The battery node should have enough capacitance to
hold the battery voltage to some minimum acceptable
system value (VSYS) during the done to fast-charge state
transition time of 100us (tDONE2FC).
is recommended. For optimum noise immunity and low
input ripple, the input capacitor value can be increased.
Note that some ceramic dielectrics exhibit large capacitance and ESR variation with temperature and DC bias.
Ceramic capacitors with Z5U or Y5V temperature characteristics should be avoided.
CBAT ≥ ILOAD x tDONE2FC/(VBATREG - VSYS)
For example, if the maximum system load without a battery is 400mA (ILOAD), and the minimum acceptable system voltage is 3.4V (VSYS), then the battery node should
have at least 40µF.
Output Capacitor Selection
For the charger, the output capacitor keeps the output
voltage ripple small and ensures regulation loop stability. The output capacitor must have low impedance at
the switching frequency. Ceramic capacitors with X5R or
X7R temperature characteristics are highly recommended due to their small size, low ESR, and small temperature coefficients. A 4.7FF capacitor is recommended. For
optimum load-transient performance and very low output
ripple, increase the output capacitor value.
CBAT ≥ 400mA x 100µs/(4.2V - 3.4V) = 40µF.
Applications Information
Inductor Selection
The charger operates with a switching frequency of
4MHz and uses a 1FH or 2.2FH inductor. This operating
frequency allows the use of physically small inductors
while maintaining high efficiency.
Charge Current Resistor Selection
Both the top-off current range and fast-charge current range depends on the sensing resistor (RSNS).
The default resistor recommended is a 47mI, 0.125W
resistor. Select a 0.125W,47mI 2% sense resistor, e.g.,
Panasonic ERJ2BWGR047. This is a standard value.
The inductor’s DC current rating only needs to match
the maximum load of the application because the IC
features zero current overshoot during startup and load
transients. For optimum transient response and high efficiency, choose an inductor with DC series resistance in
the 40mI to 120mI range. See Table 2 for suggested
inductors and manufacturers.
PRSNS = ICHARGE2 x RSNS
PRSNS = 1.52 x 0.047
PRSNS = 0.105W
Input Capacitor Selection
The charge current step (ICHARGE) is calculated using
equation below:
The input capacitor reduces the current peaks drawn
from the input power source and reduces switching noise
in the IC. The impedance of the input capacitor at the
switching frequency should be kept very low. Ceramic
capacitors with X5R or X7R temperature characteristics
are highly recommended due to their small size, low ESR,
and small temperature coefficients. A 4.7FF capacitor
ICHARGE_STEP = V(CHGCC<>)/RSNS
Table 3 below shows the charge current settings for two
sensing resistors.
ICHARGE_CURRENT_STEP = V(TOPOFF<>)/RSNS
Table 2. Suggested Inductors
MANUFACTURER
SERIES
INDUCTANCE
(µH)
ESR (I)
CURRENT
RATING
(mA)
DIMENSIONS
FDK
MIPSA2520D1R0
1.0
0.08
1500
2.5mm x 2.0mm x 1.2mm = 6mm3
Murata
LQM2HPN_G0
1.0
0.05
1600
2.5mm x 2.0mm x 0.6mm = 3mm3
Coilcraft
EPL2014
1.0
0.059
1600
2.0mm x 2.0mm x 1.4mm = 5.6mm3
TDK
MLP2520S
1.0
0.06
1500
2.0mm x 2.5mm x 1.0mm = 5mm3
TOKO
MIPF2520
2.2
0.05
1500
2.5mm x 2.0mm x 1.0mm = 5mm3
TOKO
DFE252012C
1
0.06
2500
2.5 x 2.0 x 1.2 = 6mm3
Murata
LQM32PN1R0MG0
1
0.06
1800
3.2 x 2.5 x 0.9 = 7.2mm3
���������������������������������������������������������������� Maxim Integrated Products 23
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Table 3. Charge Current Settings for 47mΩ and 68mΩ Sense Resistors
BIT
VIREG (mV)
ICHARGE (mA)
RSNS = 47mI
ICHARGE (mA)
RSNS = 68mI
V(CHGCC<11110>)
70.5
1500
1037
V(CHGCC<10100>)
47
1000
691
V(CHGCC<01010>)
23.5
500
345
Table 4. Topoff Current Settings for 47mΩ and 68mΩ Sense Resistors
BIT
V(TOPOFF)
I(TOPOFF) (mA)
RSNS = 47mI
I(TOPOFF) (mA)
RSNS = 68mI
V(TOPOFF<>)
9.4
200
138.2
V(TOPOFF<>)
4.7
100
69.1
V(TOPOFF<>)
2.35
50
34.5
Table 5. High-Level I2C Register Map
REGISTER
NAME
REGISTER
R/W
ADDRESS
RESET
CONDITION
B7
B6
B5
B4
B3
B2
B1
CHGINT
0x0F
R
VSTBY or
rising edge of
SFO_POK
AICL_I
TOPOFF
DC_
OVP
DC_
UVP
CHG_I
BAT_I
CHGINT_MSK
0x01
R/W
VSTBY or
rising edge of
SFO_POK
AICL_M
TOPOFF_
M
DC_
OVP_M
DC_
UVP_M
CHG_M
BAT_M THM_M
CHG_STAT
0x02
R
VSTBY or
rising edge of
SFO_POK
DCV_OK DCI_OK
DETAILS1
0x03
R
VSTBY or
rising edge of
SFO_POK
DC_V
DC_I
DETAILS2
0x04
R
VSTBY or
rising edge of
SFO_POK
RSVD
RSVD
DCOVP_ DCUVP_
CHG_OK
OK
OK
DC_OVP DC_UVP
BAT_DT[1:0]
RSVD
BAT_
OK
B0
THM_I POWERUP
THM_
OK
—
—
THM_D[2:0]
CHG_D[2:0]
���������������������������������������������������������������� Maxim Integrated Products 24
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Table 5. High-Level I2C Register Map (continued)
REGISTER
NAME
REGISTER
R/W
ADDRESS
RESET
CONDITION
B7
B6
B5
B4
B3
B2
B1
B0
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
DCMON_
DIS
USB_
SUS
CHGCNTL1
0x05
R/W
VSTBY or
rising edge of
SFO_POK
FCHGCRNT
0x06
R/W
VSTBY or
rising edge of
SFO_POK
DCCRNT
0x07
R/W
VSTBY or
rising edge of
SFO_POK
TOPOFF
0x08
R/W
VSTBY or
rising edge of
SFO_POK
TEMPREG
0x09
R/W
VSTBY or
rising edge of
SFO_POK
PROTCMD
0x0A
R/W
VSTBY or
rising edge of
SFO_POK
FCHGT[2:0]
RSVD
CHGCC[3:0]
CHGR
STRT
DCILMT[5:0]
TOPOFFT[2:0]
RTEMP[1:0]
RSVD
RSVD
IFST2P8
THM
CNFG
RSVD
RSVD
RSVD
TOFFS[1:0]
RSVD
CHGCV[1:0]
THMRES
C_PROT[1:0]
RSVD
SAFE
REG
RSVD
���������������������������������������������������������������� Maxim Integrated Products 25
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
I2C Registers
Charger Interrupt Requests
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
RESET
VALUE
ACCESS
TYPE
SPECIAL
FEATURES
RESET CONDITION
CHGINT
0x6A
0x0F
0x01
R
Cleared upon
read
VSTBY INVALID or
rising edge of SFO_POK
BITS
NAME
B7
B6
B5
B4
B3
B2
B1
B0
AICL_I
TOPOFF
DC_OVP
DC_UVP
CHG_I
BAT_I
THM_I
POWERUP
BIT
NAME
BIT DESCRIPTION
DEFAULT
B7
AICL_I
DC Interrupt
0 = The DC status has not changed since the last time this bit was read.
1 = The DC status has changed since the last time this bit was read.
0
B6
TOPOFF
Topoff Interrrupt
0 = The charger topoff status has not changed since the last time this bit
was read.
1 = The charger has entered topoff.
0
B5
DC_OVP
DC Overvoltage Interrupt
0 = The DC status has not changed since the last time this bit was read.
1 = The DC status has changed since the last time this bit was read.
0
B4
DC_UVP
DC Undervoltage Interrupt
0 = The DC status has not changed since the last time this bit was read.
1 = The DC status has changed since the last time this bit was read.
0
B3
CHG_I
Charge Current Interrupt
0 = The charger status has not changed since the last time this bit was read.
1 = The charger status has changed since the last time this bit was read.
0
B2
BAT_I
Battery Interrupt
0 = The battery status has not changed since the last time this bit was read.
1 = The battery status has changed since the last time this bit was read.
0
B1
THM_I
Thermistor Interrupt
0 = The THM status has not changed since the last time this bit was read.
1 = The THM status has changed since the last time this bit was read.
0
B0
POWERUP
Power-Up OK Interrupt
0 = The I2C registers have not been reset since the last time this bit was read.
1 = The I2C registers have been reset since the last time this bit was read.
1
���������������������������������������������������������������� Maxim Integrated Products 26
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Charger Interrupt Masks
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
RESET
VALUE
ACCESS
TYPE
SPECIAL
FEATURES
RESET CONDITION
CHGINT_MASK
0x6A
0x01
0x00
R/W
N/A
VSTBY INVALID or
rising edge of SFO_POK
BITS
NAME
BIT
B7
B6
B5
B4
B3
B2
B1
B0
AICL_M
TOPOFF_M
DC_
OVP_M
DC_
UVP_M
CHG_M
BAT_M
THM_M
—
NAME
BIT DESCRIPTION
DEFAULT
DC Interrupt Mask
0 = unmask
1 = mask
0
B7
AICL_M
B6
TOPOFF_M
Topoff Interrupt Mask
0 = unmask
1 = mask
0
B5
DC_OVP_M
DC Overvoltage Interrupt Mask
0 = unmask
1 = mask
0
B4
DC_UVP_M
DC Undervoltage Interrupt Mask
0 = unmask
1 = mask
0
B3
CHG_M
Charger-Current Interrupt Mask
0 = unmask
1 = mask
0
B2
BAT_M
Battery Interrupt Mask
0 = unmask
1 = mask
0
B1
THM_M
Thermistor Interrupt Mask
0 = unmask
1 = mask
0
���������������������������������������������������������������� Maxim Integrated Products 27
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Charger Status
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
RESET
VALUE
CHG_STAT
0x6A
0x02
R
BITS
NAME
BIT
ACCESS
TYPE
SPECIAL
FEATURES
RESET CONDITION
VSTBY INVALID or rising
edge of SFO_POK
N/A
B7
B6
B5
B4
B3
B2
B1
B0
DCV_OK
DCI_OK
DCOVP_
OK
DCUVP_
OK
CHG_OK
BAT_OK
THM_OK
—
NAME
BIT DESCRIPTION
B7
DCV_OK
Single-Bit DC Input Status Indicator. See DC_DTLS[1:0] for more information.
1 = The DC input is invalid. DC_V = 1.
0 = The DC input is valid. DC_DTLS[1:0]=DC_V=0.
B6
DCI_OK
1 = The DC input is invalid. DC_I = 1.
0 = The DC input is valid. DC_DTLS[1:0] =DCI=0.
B5
DCOVP_OK
1 = The DC input is invalid. DC_OVP = 1.
0 = The DC input is valid. DC_DTLS[1:0] =DC_OVP=0.
B4
DCUVP_OK
1 = The DC UVP is invalid.
0 = The DC input is valid. DC_DTLS[1:0] =DC_UVP=0.
B3
B2
B1
CHG_OK
Single-Bit Charger Status Indicator. See CHG_DTLS[3:0] for more information.
1 = The charger has suspended charging. CHG_DTLS[3:0 ] = 0b0101 or 0b0110 or 0b0111 or
0b1000.
0 = The charger is okay. CHG_DTLS[3:0] ≠ 0b0101 or 0b0110 or 0b0111 or 0b1000.
BAT_OK
Single-Bit Battery Status Indicator. See BAT_DTLS[1:0] for more information.
1 = The battery has an issue and the charger has been suspended. BAT_DTLS[1:0]=0b01 or
0b11.
0 = The battery is okay. BAT_DTLS[1:0]=0b10 or 0b00.
THM_OK
Single-Bit Thermistor Status Indicator. See the THM_DTLS[2:0] for more information.
1 = The thermistor temperature is outside of the allowable range for charging. THM_DTLS[2:0] ≠
0b100 or 0b101.
0 = The thermistor temperature is inside of the allowable range for charging. THM_DTLS[2:0] =
0b100 or 0b101.
���������������������������������������������������������������� Maxim Integrated Products 28
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
DETAILS1
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
ACCESS TYPE
SPECIAL
FEATURES
RESET CONDITION
DETAILS1
0x6A
0x03
R
N/A
VSTBY INVALID or
rising edge of
SFO_POK
BITS
NAME
BIT NAME
B7
B6
B5
B4
B3
DC_V
DC_I
DC_OVP
DC_UVP
RSVD
DESCRIPTION
B2
B1
B0
THM_D[2:0]
DEFAULT
DC_V
DC Details
0b0= VDC is in AICL mode. 3V < VDC < 4.5
0b1= VDC is valid. VDC > 4.5
Valid
DC_I
DC Details
0b0 = IDC is valid. IDC < Input current limit
0b1 = IDC is invalid. IDC > Input current limit
Valid
DC_OVP
DC Details
0b0 = VDC is valid. VDC < VDCOVLO
0b1 = VDC is invalid. VDC > VDCOVLO
Valid
DC_UVP
DC Details
0b0 = VDC is valid. VDC > VDCUVLO
0b1 = VDC is invalid. VDC < VDCUVLO
Valid
RSVD
THM_D[2:0]
Reserved
Thermistor Details
0b001 = Low temperature and charging suspended (cold, < 0°C)
0b010 = Low temperature charging (cool, > 0°C and < 10°C)
0b011 = Standard temperature charging (normal, > 10°C and < 45°C)
0b100 = High temperature charging (warm, > 45°C and < 60°C)
0b101 = High temperature and charging suspended (> 60°C)
—
Valid
���������������������������������������������������������������� Maxim Integrated Products 29
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
DETAILS2
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
ACCESS TYPE
SPECIAL
FEATURES
RESET CONDITION
DETAILS2
0x6A
0x04
R
N/A
VSTBY INVALID or rising
edge of SFO_POK
BITS
B7
B6
NAME
B5
B4
BAT_D[1:0]
NAME
B3
B2
B1
B0
CHG_D[3:0]
DESCRIPTION
DEFAULT
BAT_D[1:0]
Battery Details
0b00 = VBAT < 2.1V. This condition is also reported in the CHG_DTLS[3:0] as 0b0000
0b01 = The battery is taking longer than expected to charge. This could be due to high system
currents, an old battery, a damaged battery or something else. Charging has suspended and
the charger is in its timer fault mode. This condition is also reported in the CHG_DTLS[3:0] as
0b0110.
0b10 = The battery is OK.
0b11=The battery voltage is greater than the battery overvoltage flag threshold (BATOV),
BATOV is set to a percentage above the VBATREG target as programmed by CHGCV.
Note that this flag is only generated when there is a valid DC input.
N/A
CHG_D[3:0]
Charger Details
0b0000 = Charger is in dead-battery region.
0b0001 = Charger is in prequalification mode.
0b0010 = Charger is in fast-charge constant-current mode.
0b0011 = Charger is in fast-charge constant voltage mode.
0b0100 = Charger is in top-off mode.
0b0101 = Charger is in done mode.
0b0110 = Charger is in timer fault mode.
0b0111 = Charger is in temperature suspend mode, see THM_DTLS[2:0].
0b1000 = Charger is off, DC is invalid and/or charger is disabled.
0b1001 = Charger is in prequalification, fast-charge or top-off modes and is operating with its
thermal loop active (i.e., the junction temperature is greater than the value set by
REGTEMP[1:0].
N/A
���������������������������������������������������������������� Maxim Integrated Products 30
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
USB Suspend
Input Voltage Disable
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
ACCESS TYPE
SPECIAL
FEATURES
RESET CONDITION
CHGCNTL1
0x6A
0x05
R/W
N/A
VSTBY INVALID or rising
edge of SFO_POK
B7
BITS
NAME
B6
B5
B4
B3
B2
B1
DCMON_DIS
B0
USB_SUS
BIT NAME
BIT DESCRIPTION
DEFAULT
­—
—
0
—
—
0
—
—
0
—
—
0
—
—
0
—
0
—
DCMON_DIS
USB_SUS
DCMON_DIS, disabled the monitoring of input voltage by the input power limiter
0
USB suspend, low-quiescent current standby mode
0
Fast-Charge Current and Timer Control
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
ACCESS TYPE
SPECIAL
FEATURES
RESET CONDITION
FCHGCRNT
0x6A
0x06
R/W
Protected with
CPROT[1:0]
VSTBY INVALID or rising
edge of SFO_POK
BITS
NAME
BIT
B4–B0
B7, B6, B5
B7
NAME
B6
FCHGT[2:0]
B5
B4
B3
B2
CHGCC[4:0]
B1
DESCRIPTION
B0
DEFAULT
CHGCC[4:0]
Fast-Charge Current Selection
When the charger is enabled, the charge current limit is set by these bits. These
bits range from 250mA to 1.55A in 50mA steps. See Table 6 for a complete
listing of codes for CHGCC[4:0]
500mA
FCHGT[2:0]
Fast-Charge Timer Duration (tFC)
0x00 = 0b000 = disable
0x01 = 0b001 = 4hrs
0x02 = 0b010 = 5hrs
0x03 = 0b011 = 6hrs
0x04 = 0b100 = 7hrs
0x05 = 0b101 = 8hrs
0x06 = 0b110 = 9hrs
0x07 = 0b111 = 10hrs
0b010
���������������������������������������������������������������� Maxim Integrated Products 31
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Table 6. CHGCC[4:0] Decoding
CHARGE CURRENT with
47mΩ Sense
(mA)
250
250
250
250
250
250
300
350
400
450
500
550
600
650
700
750
CHGCC[4:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
CHGCC[4:0]
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
CHARGE CURRENT with
47mΩ Sense
(mA)
800
850
900
950
1000
1050
1100
1150
1200
1250
1300
1350
1400
1450
1500
1550
Input-Current Limit and Charger Restart Threshold
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
ACCESS TYPE
SPECIAL
FEATURES
RESET CONDITION
DCCRNT
0x6A
0x07
R/W
Protected with
CPROT[1:0]
VSTBY INVALID or rising edge
of SFO_POK
BITS
NAME
B7
B6
CHGRSTRT
B5
NAME
B4
B3
B2
DCILMT[5:0]
DESCRIPTION
CHGRSTRT
Fast-Charge Restart Threshold
0b0 = -150mV
0b1 = -100mV
DCILMT[5:0]
Input-Current Limit Selection
When the DC-DC converter is on, the VDC input current limit is set by this
register. The bits set 100mA, to 1.5A in 25mA steps. See Table 7 for a complete
listing of the codes for DCILMT[5:0].
B1
B0
DEFAULT
0b0
500mA
���������������������������������������������������������������� Maxim Integrated Products 32
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Table 7. DCILMT[5:0] Bit Code
TARGET INPUT LIMIT
(mA)
DCILMT[5:0]
0
0
0
0
0
0
100
0
0
0
0
0
1
100
0
0
0
0
1
0
100
0
0
0
0
1
1
100
0
0
0
1
0
0
100
0
0
0
1
0
1
100
0
0
0
1
1
0
100
0
0
0
1
1
1
100
0
0
1
0
0
0
100
0
0
1
0
0
1
100
0
0
1
0
1
0
250
0
0
1
0
1
1
275
0
0
1
1
0
0
300
0
0
1
1
0
1
325
0
0
1
1
1
0
350
0
0
1
1
1
1
375
0
1
0
0
0
0
400
0
1
0
0
0
1
425
0
1
0
0
1
0
450
0
1
0
0
1
1
475
0
1
0
1
0
0
500
0
1
0
1
0
1
525
0
1
0
1
1
0
550
0
1
0
1
1
1
575
0
1
1
0
0
0
600
0
1
1
0
0
1
625
0
1
1
0
1
0
650
0
1
1
0
1
1
675
0
1
1
1
0
0
700
0
1
1
1
0
1
725
0
1
1
1
1
0
750
0
1
1
1
1
1
775
1
0
0
0
0
0
800
1
0
0
0
0
1
825
1
0
0
0
1
0
850
1
0
0
0
1
1
875
1
0
0
1
0
0
900
1
0
0
1
0
1
925
1
0
0
1
1
0
950
1
0
0
1
1
1
975
1
0
1
0
0
0
1000
���������������������������������������������������������������� Maxim Integrated Products 33
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Table 7. DCILMT[5:0] Bit Code (continued)
TARGET INPUT LIMIT
(mA)
DCILMT[5:0]
1
0
1
0
0
1
1025
1
0
1
0
1
0
1050
1
0
1
0
1
1
1075
1
0
1
1
0
0
1100
1
0
1
1
0
1
1125
1
0
1
1
1
0
1150
1
0
1
1
1
1
1175
1
1
0
0
0
0
1200
1
1
0
0
0
1
1225
1
1
0
0
1
0
1250
1
1
0
0
1
1
1275
1
1
0
1
0
0
1300
1
1
0
1
0
1
1325
1
1
0
1
1
0
1350
1
1
0
1
1
1
1375
1
1
1
0
0
0
1400
1
1
1
0
0
1
1425
1
1
1
0
1
0
1450
1
1
1
0
1
1
1475
1
1
1
1
0
0
1500
1
1
1
1
1
1
Disable
Note: DCILIM threshold is 95% of target.
���������������������������������������������������������������� Maxim Integrated Products 34
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Done Current, Timer, GSM Test Mode, and Battery Regulation Voltage
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
ACCESS TYPE
SPECIAL
FEATURES
RESET CONDITION
TOPOFF
0x6A
0x08
R/W
Protected with
CPROT[1:0]
VSTBY INVALID or rising
edge of SFO_POK
B4
B3
B7
BITS
B6
TOFFT[2:0] NAME
NAME
TOFFT[2:0]
B5
IFST2p8
B2
TOFFS[1:0]
DESCRIPTION
Topoff Timer Setting
0x00 = 0b000 = 0min
0x01 = 0b001 = 10min
0x02 = 0b010 = 20min
0x03 = 0b011 = 30min
0x04 = 0b100 = 40min
0x05 = 0b101 = 50min
0x06 = 0b110 = 60min
0x07 = 0b111 = 70min
B1
B0
CHGCV[1:0]
DEFAULT
0b011
Scales Maximum Fast-Charge Current to 2.8A
This is used as a pulsed customer test mode and the part cannot run 2.8A
continuously.
0b0
TOFFS[1:0]
Topoff Current Threshold
Topoff timer starts when ICHG reaches this current setting.
0x0 = 0b00 = 50mA
0x1 = 0b01 = 100mA
0x2 = 0b10 = 150mA
0x3 = 0b11 = 200mA
0b00
CHGCV[1:0]
Charge Termination Voltage Setting
0x00 = 0b00 = 4.2V
0x01 = 0b01 = 4.10V
0x02 = 0b10 = 4.35V
0x03 = 0b11 = 4.15V
0b00
IFST2P8
���������������������������������������������������������������� Maxim Integrated Products 35
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Temperature Regulation
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
ACCESS
TYPE
SPECIAL
FEATURES
RESET CONDITION
TEMPREG
0x6A
0x09
R/W
Protected with
CPROT[1:0]
VSTBY INVALID or rising
edge of SFO_POK
B7
BITS
B6
REGTEMP[1:0]
NAME
B5
B4
B3
THM_CNFG
—
— NAME
B2
B1
THMRES[1:0] BIT DESCRIPTION
B0
SAFETYREG
DEFAULT
Die-Temperature Thermal Regulation Loop Setpoint
0x0 = 0b00 = 105°C
0x1 = 0b01 = 90°C
0x2 = 0b10 =120°C
0x3 = 0b11 = Disabled
0b00
Thermistor Monitor Configuration
0b0 = The thermistor is continuously monitored.
0b1 = The thermistor is not being monitored.
0b1
Reserved
Reserved
NA
Reserved
Reserved
NA
JEITA Safety Region Selection
0 = Safety region 1
1 = Safety region 2
0b0
REGTEMP[1:0]
THM_CNFG
SAFETYREG
Charger Protection
REGISTER
NAME
I2C SLAVE
ADDRESS
REGISTER
ADDRESS
ACCESS TYPE
SPECIAL
FEATURES
RESET CONDITION
PROTCMD
0x6A
0x0A
R/W
N/A
VSTBY INVALID or rising
edge of SFO_POK
BITS
B7
B6
B5
B4
NAME
—
—
—
—
NAME
CPROT[1:0]
B3
B2
CPROT[1:0]
DESCRIPTION
Charger-Setting Protection Bits
Writing 11 to these bits unlocks the settings for the above registers. Writing any
value besides 11 locks these registers.
0b00 = locked
0b01 = locked
0b10 = locked
0b11 = unlocked
B1
B0
—
—
DEFAULT
0b00
���������������������������������������������������������������� Maxim Integrated Products 36
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Simplified Applications Circuit
-0.3V TO +22V
TOLERANT
4.0V TO 10V OPERATIONAL
DC
DC1,
DC2
BST
BYP
SFO
PVL
AVL
GND
MAX8971
VICHG
LX1,
LX2
PG1,
PG2
CS
I2CIN
BAT+
BAT
IRQB
µP
BAT+
SYSTEM
LOAD
SDA
THM
SCL
AVL
Ordering Information
PART
MAX8971EWP+
TEMP RANGE
PIN-PACKAGE
-40NC to +85NC
20-Bump WLP
(0.4mm pitch)
Chip Information
PROCESS: BiCMOS
+Denotes a lead(Pb)-free/RoHS-compliant package.
���������������������������������������������������������������� Maxim Integrated Products 37
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Package Information
For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains
to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
OUTLINE
NO.
LAND
PATTERN NO.
20 WLP
W201B2-1
21-0544
Refer to Application Note 1891
E
PIN 1
INDICATOR
COMMON DIMENSIONS
MARKING
1
A3
A
A1
AAAA
D
A2
0.05 S
0.64
0.05
A1
0.19
0.03
0.45 REF
A2
A
0.025 BASIC
A3
0.27
b
S
See Note 7
SIDE VIEW
TOP VIEW
A
E1
SE
0.03
D1
1.20 BASIC
E1
1.60 BASIC
e
0.40 BASIC
SD
0.20
BASIC
SE
0.00
BASIC
e
B
E
D
C
B
SD
D1
A
1
2
3
4
5
b
0.05 M
S
AB
D
DEPOPULATED
BUMPS
PKG. CODE
MIN
MAX
MIN
MAX
W201A2+1
2.33
2.36
1.92
1.95
NONE
W201B2+1
2.16
2.19
1.60
1.63
NONE
W201C2+1
2.01
2.04
1.61
1.64
NONE
W201D2+1
2.08
2.11
1.71
1.74
NONE
A
BOTTOM VIEW
NOTES:
1. Terminal pitch is defined by terminal center to center value.
2. Outer dimension is defined by center lines between scribe lines.
3. All dimensions in millimeter.
4. Marking shown is for package orientation reference only.
5. Tolerance is ± 0.02 unless specified otherwise.
6. All dimensions apply to PbFree (+) package codes only.
7. Front - side finish can be either Black or Clear.
-DRAWING NOT TO SCALE-
TITLE
APPROVAL
PACKAGE OUTLINE
20 BUMPS, WLP PKG. 0.4mm PITCH
DOCUMENT CONTROL NO.
21-0544
REV.
B
1
1
���������������������������������������������������������������� Maxim Integrated Products 38
MAX8971
Industry's Smallest 1.55A
1-Cell Li+ DC-DC Charger
Revision History
REVISION
NUMBER
REVISION
DATE
0
1/12
DESCRIPTION
Initial release
PAGES
CHANGED
—
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2012
Maxim Integrated Products 39
Maxim is a registered trademark of Maxim Integrated Products, Inc.