Tube Liquid Sensor OPB350 Series Features: “N” Package • Can identify if liquid is present in clear tubes that have an outside diameter of 1/8" (3.2mm), 3/16" (4.8mm) or 1/4" (6.3mm) • Opaque plastic housing enhances ambient light rejection • Printed circuit board mounting or 24” (610 mm) wires Product Photo Here “T” Package Description: The OPB350 series liquid sensor is designed to work with 1/8” (3.2mm), 3/16” (4.8mm) and 1/4” (6.3mm) outside diameter clear tubes. When output reference circuitry is added, multiple output states such as “fluid present,” “no fluid present” and “no tube present” can be recognized. Clear liquid present causes the phototransistor to sink the maximum current, while dark liquid present causes it to sink the minimum current. As bubbles pass through the tube, the signal will vary between the “liquid present” and “no liquid” states. If no liquid is present, the phototransistor sinks only a small amount of current. If no tube is present, the phototransistor sinks a larger current than in the “no liquid” state. Smaller outside diameter tubes can be used when the tube is sized up to one of the standard sizes and is fitted properly in the housing opening. For example, fluid in a 1/16” (1.6mm) outside diameter tube can be sensed when a piece of tubing with a 1/8” (3.2mm) outside diameter and a 1/16” (1.6mm) inside diameter is used as an adapter. Ordering Information Applications: • • • • • • Non-contact fluid sensing Part Number Package IV fluid LED Peak Wavelength Tube Size Sensor 0.125" OPB350 Oils and other petroleum products Colored fluids 0.187" N OPB350L187 Toner fluids 890 nm OPB350L250 Water Lead Length / Spacing Transistor 0.330” / 0.320” 0.250" 0.187" OPB350W187Z T 24" / 26 AWG Wire 0.250" OPB350W250Z Typical Application Circuit R3=750 R1=1K R1=500 Vcc 4 Vth 1 Vth 2 R4=2K Gnd Vcc OPB350 LM339 or LM393 R2=2K C1=0.1 uf R4=2.5K Vth 1 C1=0.1 uf Output 1 LM339 or LM393 Opto Switch Output 2 Vth 2 Gnd RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.4 02/06 Page 1 of 4 Tube Liquid Sensor OPB350 Series OPB350 Pin # LED 1 Anode Pin # Transistor 3 Collector 2 Cathode 4 Emitter 1 3 2 Dot 4 OPB350L187 and OPB350L250 Pin # LED 1 Anode 3 Collector 2 Cathode 4 Emitter 1 Pin # Transistor 3 Dot Dot 2 4 OPB350W187Z and OPB350W250Z Pin # LED Pin # Transistor Red Anode White Collector Black Cathode Green Emitter Red-1 White-3 Black-2 Green-4 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 02/06 Page 2 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Tube Liquid Sensor OPB350 Series Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage Temperature -40° C to +100° C Operating Temperature -40° C to +85° C Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] (2) 260° C LED Forward DC Current 50 mA Peak Forward Current (2 µs pulse width, 0.1% duty cycle) 1A Reverse DC Voltage 2V Power Dissipation 100 mW Output Phototransistor Collector-Emitter Voltage 25 or 30 V Collector DC Current 50 mA Power Dissipation 100 mW Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input LED (See OPB245 for additional information — for reference only) VF Forward Voltage - - 1.8 V IF = 20 mA IR Reverse Current - - 100 µA VR = 2.0 V Output Phototransistor (See OPB555 [PB350] & OP750 [-187 & -250] for additional information — for reference only) V(BR)CEO ICEO Collector-Emitter Breakdown Voltage OPB350 -187 & -250 Collector-Emitter Dark Current 30 25 - - V IC = 100 µA, EE = 0 mw/cm2 - - 100 nA VCE = 10 V, IF = 0, EE = 0 mw/cm2 Coupled (Tested using clear 0.125” O.D., 0.062 I.D. nylon tubing) VCE(SAT) IC(ON) On/Off Ratio Collector-Emitter Saturation Voltage On-State Collector Current OPB350 OPB350L187 & OPB350W187 OPB350L250 & OPB350W250 OPB350 OPB350L187 & OPB350W187 OPB350L250 & OPB350W250 - - 0.4 V IC = 100 µA, IF = 5 mA 1 1 0.75 3.5 2 1.5 6 4 3 mA mA mA VCE = 0.4 V, IF = 5 mA VCE = 0.4 V, IF = 5 mA VCE = 0.4 V, IF = 5 mA - 3 2.3 2.3 - - VCE = 0.4 V, IF = 5 mA , I.D.=0.0625” VCE = 0.4 V, IF = 5 mA , I.D.=0.0870” VCE = 0.4 V, IF = 5 mA , I.D.=0.1250” Notes: (1) All parameters tested using pulse technique. (2) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (3) Methanol or isopropanol are recommended as cleaning agents. The plastic housing is soluble in chlorinated hydrocarbons and keytones. (4) Derate linearly 1.33 mW/° C above 25° C. (5) Ee(APT) is a measurement of the average apertured radiant energy incident upon a sensing area 0.250” (6.350 mm) in diameter, which is perpendicular to and centered to the mechanical axis of the emitting surface at a distance of 0.466” (11.837 mm). Ee(APT) is not necessarily uniform within the measured area. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.4 02/06 Page 3 of 4 Tube Liquid Sensor OPB350 Series ( Typical VSAT vs Temperature 1.2 0.09 ) Normalized IC(ON) vs Temperature Normalized @ T=20°C 0.08 1.0 0.06 Relative I C(ON) V SAT (Volts) 0.07 0.05 0.04 0.03 0.8 0.6 0.4 0.02 0.2 0.01 Normalized @ IF = 5mA, ICE = 100uA 0.0 0.00 -40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100 Temperature (°C) Temperature (°C) Rise & Fall Time vs Load Resistance Test Circuit (Rise & Fall Time) 300 VR2 = 1.0 Rise & Fall Time (usec) 250 Fall 200 150 100 50 Rise 0 1 2 3 4 5 6 7 8 9 10 Load Resistance (,000 Ohms) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 02/06 Page 4 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com