19-3278; Rev 1; 7/04 150Mbps Automotive Fiber Optic Receivers The MAX3901/MAX3902 are optimized for low-cost polymer-clad silica (PCS) and plastic optical fiber (POF) automotive receivers. These parts operate over an extended -40°C to +140°C (junction) temperature range. The MAX3901 features a 1.2µA to 1mA input range, a +3.3V or +5V supply voltage, operation from 8Mbps to 50Mbps, and a TTL output compatible with common automotive optical network interfaces. The MAX3902 features a 1.2µA to 1mA input range, +3.3V supply voltage, operation from 40Mbps to 150Mbps, and a differential output compatible with LVDS, PECL, and IEEE 1394b (S100β). Both circuits provide an input power detect and lowpower standby mode with status output. No filter capacitors are required in the optical subassembly, thus enabling a low-cost receiver design. The circuits are available in die and wafer form. Features ♦ -40°C to +140°C Operating Junction Temperature ♦ Operation Up to 50Mbps (MAX3901) ♦ Operation Up to 150Mbps (MAX3902) ♦ +3.3V or +5.0V Power Supply (MAX3901) ♦ 1.2µAP-P Input Sensitivity ♦ 1mAP-P Input Overload ♦ Input Power Detect with Power-Reducing Standby Mode ♦ Active Output Pulldown During Standby Mode (MAX3901) ♦ Differential LVDS- or PECL-Compatible Output (MAX3902) ♦ TTL-Compatible Output (MAX3901) ♦ No Filter Capacitors Required in the Optical Subassembly Applications Ordering Information Automotive Fiber Optic Receivers IEEE 1394b (S100β) PART TEMP RANGE PIN-PACKAGE MAX3901E/D -40°C to +140°C Dice* MAX3902E/D -40°C to +140°C Dice* *Dice are designed to operate over a -40°C to +140°C junction temperature (Tj) range, but are tested and guaranteed at TA = +75°C. Typical Operating Circuits +5.0V VCC OPTICAL RECEIVER SUPPLY FILTER +3.3V OPTICAL RECEIVER VCC FILT +3.3V SWITCHED VCC STATUS STATUS FILT MAX3901 IN SUPPLY FILTER OUT_TTL STATUS MAX3902 RX DATA TTL INPUT (SP4 AUTOMOTIVE NETWORK INTERFACE) IN 82Ω OUT+ PECL INPUT OUT0.1µF GND GND 82Ω 0.1µF 130Ω 130Ω GND Typical Operating Circuits continued at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX3901/MAX3902 General Description MAX3901/MAX3902 150Mbps Automotive Fiber Optic Receiver ABSOLUTE MAXIMUM RATINGS Supply Voltage (VCC) ...............................................-0.5V to +6V Current into IN ....................................................................±3mA Voltage at OUT+, OUT- (MAX3902) .............................0V to +6V Current into OUT_TTL (MAX3901)....................................±10mA Current into FILT ..................................................................-3mA Voltage at STATUS .......................................-0.5V to (VCC + 0.5) Operating Junction Temperature Range ............-55°C to +150°C Storage Temperature Range .............................-65°C to +175°C Die Attach Temperature...................................................+400°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS—MAX3901 (VCC = +3.135V to +5.25V, CPD = 2pF; Tj = -40°C to +140°C. Typical values are at VCC = +5.0V and TA = +25°C, unless otherwise noted.) PARAMETER SYMBOL CONDITION MIN TYP MAX UNIT POWER SUPPLY Operating Power-Supply Current ICC Standby Current ISTBY Power-Up Time tPU TJ < +100°C 14 TJ < +140°C 22 28 TJ < +85°C 10 TJ < +125°C 20 80 From valid VCC to STATUS low 0.06 mA µA 1 ms 50 Mbps 0.4 1.2 µAP-P 0.8 1.0 -0.35 -0.45 INPUT PARAMETERS Data Rate Input Extinction Ratio Er Input Sensitivity 8 10log (P1 / P0) 3 (Notes 1, 2) IIN ≤ 600µA Input Overload Input Bias Voltage Maximum 3 CIDs dB 1.0 VIN mAP-P V FILT PIN Voltage at FILT VFILT Filter Resistor RFILT IFILT = -600µA, referenced to VCC 100 V kΩ DATA OUTPUT (OUT_TTL) RLOAD = 50kΩ to GND, COUT = 15pF Output High VOH Output Low VOL Output Voltage During Standby 2.5 STATUS = high, IOUT = 30µA Output Switching Time tr, tf 10% to 90%, data rate ≤ 45Mbps Pulse-Width Variation PWV 45Mbps (Notes 1, 3), 1.2µAP-P ≤ iIN ≤ 1mAP-P 0.86 Average Pulse-Width Distortion PWD 45Mbps (Notes 1, 3) -0.07 Data-Dependent Jitter DDJ (Notes 1, 4) iIN ≥ 1.2µAP-P (Note 1) Uncorrelated Jitter (Random Jitter) RJ 2.7 V 0.3 0.4 V 0.06 0.4 V 5 8.5 ns 1.14 UI +0.07 UI 0.035 0.082 UI 0.007 0.015 UIRMS POWER DETECT (STATUS) Input for STATUS High ISTH Standby mode Input for STATUS Low ISTL Operating mode STATUS Low Voltage VSTATUS-L ISTATUS < 1mA STATUS High Voltage 2 VSTATUS-H ISTATUS > -25µA ISTATUS > -20µA, VCC ≥ 4.75V 50 160 210 2.4 4 _______________________________________________________________________________________ nA 630 nA 0.4 V V 150Mbps Automotive Fiber Optic Receiver (VCC = +3.135V to +5.25V, CPD = 2pF; Tj = -40°C to +140°C. Typical values are at VCC = +5.0V and TA = +25°C, unless otherwise noted.) PARAMETER SYMBOL STATUS Resistance CONDITION MIN TYP MAX 10 16 24 kΩ Transition to operating mode (Note 5) 0.2 0.5 ms Transition to standby mode (Note 6) 16 100 µs RSTATUS tOP Power-Detect Time tSTBY UNIT Note 1: Guaranteed by design and characterization. Note 2: BER = 1E-9, biphase-coded data containing three consecutive, identical digits. Waveform shaped by 39MHz four-pole filter. Note 3: See Figure 1. VTH is 1.5V for the MAX3901, 0V for (AC-coupled) differential output from the MAX3902. Data is biphase-coded with three consecutive, identical digits added. Data input to the MAX3901 is shaped by a 39MHz four-pole filter. Data input to the MAX3902 is shaped by a 117MHz four-pole filter. Maximum PWV = MAX [t1max, t2max - 1UI, t3max - 2UI]. Minimum PWV = MIN [t1min, t2min - 1UI, t3min - 2UI]. Minimum PWD = MIN [(tn-max + tn-min -2 x n x UI)/2], where n = 1, 2, 3. Maximum PWD = MAX [(tn-max + t+n-min -2 x n x UI)/2], where n = 1, 2, 3. Note 4: Data-dependent jitter is measured as shown in MOST Specification of Physical Layer, Version 1.1, data rate = 45Mbps. Note 5: Time from IIN > ISTL to STATUS = low, CSTATUS < 10pF. Note 6: Time from IIN < ISTH to STATUS = high, CSTATUS < 10pF. t3max t2max t1max VTH t1min t2min t3min TRIGGER ON RISING EDGE Figure 1. PWV and PWD Timing Diagrams _______________________________________________________________________________________ 3 MAX3901/MAX3902 ELECTRICAL CHARACTERISTICS—MAX3901 (continued) MAX3901/MAX3902 150Mbps Automotive Fiber Optic Receiver ELECTRICAL CHARACTERISTICS—MAX3902 (VCC = +3.0V to +3.6V, CPD = 2pF; Tj = -40°C to +140°C. Typical values are at VCC = +3.3V and TA = +25°C, unless otherwise noted.) PARAMETER SYMBOL CONDITION MIN TYP MAX UNIT 26 35 mA POWER SUPPLY Operating Power-Supply Current ICC Standby Current ISTBY Power-Up Time tPU TJ < +85°C 9 TJ < +125°C 18 80 From valid VCC to STATUS low 0.06 µA 1 ms 150 Mbps 1.2 µAP-P INPUT PARAMETERS Data Rate Input Extinction Ratio Er Maximum 5 CIDs 40 10log (P1 / P0) 3 Input Sensitivity (Notes 1, 7) Input Overload IIN ≤ 600µA Input Bias Voltage dB 1.0 VIN mAP-P 0.75 1.0 V -0.35 -0.45 V FILT PIN PARAMETERS Voltage at FILT VFILT Filter Resistor RFILT IFILT = -600µA, referenced to VCC 100 kΩ DIFFERENTIAL OUTPUT Differential Signal Output VOUT Total signal measured between the two outputs 600 800 1000 Output Resistance ROUT Single ended 85 mVP-P 100 115 Ω Output Switching Time tr, tf 10% to 90%, iIN ≥ 2µAP-P 1.5 2.5 ns Deterministic Jitter DJ (Notes 1, 8) 0.03 0.10 UI iIN = 2.0µAP-P, Er = 3dB, input filter 117MHz (Note 1) 135 215 iIN = 2µAP-P, Er = 10dB, input filter = 117MHz 122 Random Jitter RJ Pulse-Width Variation PWV (Notes 1, 3) 2µAP-P ≤ iIN ≤ 1mAP-P Average Pulse-Width Distortion PWD (Notes 1, 3) Data-Dependent Jitter DDJ (Notes 1, 4) Input for STATUS High ISTH Standby mode Input for STATUS Low ISTL Operating mode STATUS Low Voltage VSTATUS-L ISTATUS < 1mA STATUS High Voltage VSTATUS-H ISTATUS > -25µA psRMS 0.88 -0.045 0.01 1.12 UI +0.042 UI 0.071 UI 630 nA 0.4 V 24 kΩ POWER DETECT (STATUS) STATUS Resistance Power-Detect Time RSTATUS tOP tSTBY 50 160 210 nA 2.4 10 V 16 Transition to operating mode (Note 5) 0.2 0.5 ms Transition to standby mode (Note 6) 16 100 µs Note 7: BER = 1E-9, test pattern is K28.5 (00111110101100000101), waveform shaped by a 117MHz four-pole filter. Note 8: Tested with K28.5 pattern at 45Mbps and 150Mbps, 2.0µAP-P < iIN < 1mAP-P, waveform shaped by 117MHz four-pole filter. Deterministic jitter (DJ) is the peak-to-peak deviation from ideal time crossings, measured at the zero-level crossings of the differential output. 4 _______________________________________________________________________________________ 150Mbps Automotive Fiber Optic Receiver 25 20 15 10 5 300 INPUT CURRENT (nA) 30 SUPPLY CURRENT (µA) 30 350 MAX3901/02 toc02 35 MAX3901/02 toc01 35 25 20 15 10 0 20 40 60 80 100 120 140 200 150 STATUS = HIGH -40 -20 TEMPERATURE (°C) 0 20 40 60 -40 -20 80 100 120 140 0 FILTER VOLTAGE vs. FILTER CURRENT 400 350 OUTPUT VOLTAGE (mV) 4.6 40 60 80 100 120 140 OUTPUT VOLTAGE vs. OUTPUT CURRENT IN STANDBY MODE MAX3901/02 toc04 5.0 20 TEMPERATURE (°C) TEMPERATURE (°C) 4.2 3.8 MAX3901/02 toc05 0 250 50 0 -40 -20 STATUS = LOW 100 5 FILTER VOLTAGE (V) SUPPLY CURRENT (mA) STATUS THRESHOLDS vs. TEMPERATURE SUPPLY CURRENT DURING STANDBY vs. TEMPERATURE MAX3901/02 toc03 SUPPLY CURRENT vs. TEMPERATURE 300 250 200 150 100 3.4 50 3.0 0 1µ 10µ 100µ FILTER CURRENT (A) 1m 0 20 40 60 80 100 120 OUTPUT CURRENT (µA) _______________________________________________________________________________________ 5 MAX3901/MAX3902 MAX3901 Typical Operating Characteristics (VCC = +5.0V, CPD = 2pF, test pattern is biphase-coded data with 3 CIDs at 50Mbps, TA = +25°C, unless otherwise noted.) MAX3901 Typical Operating Characteristics (continued) (VCC = +5.0V, CPD = 2pF, test pattern is biphase-coded data with 3 CIDs at 50Mbps, TA = +25°C, unless otherwise noted.) 150 BIT ERROR RATE 200 Er = 3dB Er = 10dB 100 1.0E-07 1.0E-08 1.0E-09 50 1.0E-10 0 10µ 100µ 1m SILICON PHOTODIODE 850nm SOURCE, Er >10dB, BER = 1E-9 -25 -27 -29 -31 -33 -35 1.0E-11 1µ -37 -33 -32.5 -32 -31.5 -31 -40 OPTICAL INPUT (dBm OMA) INPUT AMPLITUDE (AP-P) OUTPUT EYE DIAGRAM (+3dBm OMA OPTICAL INPUT AT +25°C SILICON PHOTODIODE WITH 850nm SOURCE) -20 0 20 OUTPUT EYE DIAGRAM (-27dBm OMA OPTICAL INPUT AT +25°C SILICON PHOTODIODE WITH 850nm SOURCE) 6 MAX3901/02 toc10 500mV/div 4ns/div 40 60 TEMPERATURE (°C) MAX3901/02 toc09 500mV/div MAX3091/02 toc08 1.0E-06 -23 OPTICAL POWER (dBm OMA) 250 SILICON PHOTODIODE 850nm SOURCE, Er >10dB MAX3901/02 toc07 1.0E-05 MAX3901/02 toc06 300 OPTICAL SENSITIVITY vs. TEMPERATURE BER vs. OPTICAL INPUT UNCORRELATED (RANDOM) JITTER vs. INPUT AMPLITUDE UNCORRELATED (RANDOM) JITTER (psRMS) MAX3901/MAX3902 150Mbps Automotive Fiber Optic Receiver 4ns/div _______________________________________________________________________________________ 80 100 150Mbps Automotive Fiber Optic Receiver 20 15 10 400 350 300 250 +140°C -40°C 200 150 100 5 -21 +25°C -40 -20 0 20 40 60 80 100 120 140 10µ 100µ OUTPUT EYE DIAGRAM (2µAP-P ELECTRICAL INPUT AT TJ = -40°C) -27 -29 -40 -20 0 20 40 60 80 100 TEMPERATURE (°C) OUTPUT EYE DIAGRAM (2µAP-P ELECTRICAL INPUT AT TJ = +140°C) MAX3901/02 toc15 MAX3901/02 toc16 MAX3901/02 toc14 1.0E-05 -25 1m BER vs. OPTICAL INPUT 1.0E-04 BIT ERROR RATE 1µ INPUT AMPLITUDE (A) SILICON PHOTODIODE 850nm SOURCE, Er >10dB -23 -33 0 JUNCTION TEMPERATURE (°C) 1.0E-03 SILICON PHOTODIODE 850nm SOURCE, BER = 1E-9, Er >10dB -31 50 0 MAX3091/02 toc13 450 OPTICAL POWER (dBm) 25 -19 MAX3901/02 toc12 SUPPLY CURRENT (mA) 30 500 DETERMINISTIC JITTER (ps) MAX3901/02 toc11 35 OPTICAL SENSITIVITY vs. TEMPERATURE DETERMINISTIC JITTER vs. INPUT AMPLITUDE SUPPLY CURRENT vs. TEMPERATURE 1.0E-06 125mV/div 1.0E-07 125mV/div 1.0E-08 1.0E-09 1.0E-10 1.0E-11 -30 -29 -28 1.25ns/div 1.25ns/div OUTPUT EYE DIAGRAM (-27.7dBm OMA OPTICAL INPUT AT TJ = +25°C) SILICON PHOTODIODE WITH 850nm SOURCE OUTPUT EYE DIAGRAM (+3dBm OMA OPTICAL INPUT AT TJ = +25°C) SILICON PHOTODIODE WITH 850nm SOURCE -27 OPTICAL INPUT (dBm OMA) OUTPUT EYE DIAGRAM (1mAP-P ELECTRICAL INPUT AT TJ = +25°C) 125mV/div 125mV/div 125mV/div 1.25ns/div MAX3901/02 toc19 MAX3901/02 toc18 MAX3901/02 toc17 1.25ns/div 1.25ns/div _______________________________________________________________________________________ 7 MAX3901/MAX3902 MAX3902 Typical Operating Characteristics (VCC = +5.0V, CPD = 2pF, test pattern is K28.5 at 150Mbps, TA = +25°C, unless otherwise noted.) 150Mbps Automotive Fiber Optic Receiver MAX3901/MAX3902 Pad Description BOND PAD MAX3901 NAME MAX3902 NAME FUNCTION 1 FILT FILT Filter Pin. Must be connected to photodiode cathode for the IC to operate. This pin provides connection to an integrated photodiode filter. 2 IN IN 3, 4, 13, 14, 15 N.C. N.C. No Connection Data Input. Connect photodiode anode to this pin. 5, 6, 7 VCC VCC Supply Voltage 8, 16, 17 GND GND Circuit Ground 9 N.C. OUT+ Noninverting Data Output. Current flowing into IN causes the voltage at OUT+ to increase. 10 N.C. OUT- Inverting Data Output. Current flowing into IN causes the voltage at OUT- to decrease. 11 STATUS STATUS 12 OUT_TTL N.C. Status Monitor. STATUS is TTL low when the receiver is in operating mode. STATUS is TTL high when the receiver is in standby mode. TTL Data Output. Current flowing into IN causes the voltage at OUT_TTL to increase. Detailed Description The MAX3901/MAX3902 receivers are optimized for automotive fiber optic applications. The MAX3901 is a single-ended TTL output receiver. The MAX3902 is a differential CML output receiver. The MAX3901/ MAX3902 are both comprised of a transimpedance amplifier, a voltage-gain amplifier, an output buffer, a DC cancellation circuit, and a power detector with status monitor, as shown in Figure 2. CML Output Buffer The output buffer for the MAX3902 is a differential CML output designed to drive a 100Ω differential load between OUT+ and OUT- (Figure 3). For optimum supply noise rejection, the MAX3902 should be terminated with a differential load. If a single-ended output is required, both the used and the unused outputs should be terminated in a similar manner. Signal Path The signal path consists of a transimpedance amplifier, a voltage-gain amplifier, and a DC cancellation circuit. The transimpedance amplifier converts input current to voltage. The voltage-gain amplifier converts single-ended to differential voltage. The DC cancellation circuit uses lowfrequency feedback to remove the DC component of the input signal. This feature centers the input signal within the transimpedance amplifier’s linear range, thereby reducing pulse-width distortion. The highpass response of the DC cancellation circuit limits the number of consecutive identical digits that can be tolerated. TTL Output Buffer The output buffer for the MAX3901 is a single-ended TTL output designed to drive a high-impedance load. Output capacitance should be less than 15pF to ensure stable operation. The TTL output is not compatible with 50Ω test equipment. Use a high-impedance probe to monitor the output. During standby mode, the TTL output is actively pulled to a low state. VCC MAX3901 MAX3902 FILT POWER DETECTOR STATUS VCC INTERNAL VOLTAGE AMPLIFIER IN TIA OUT+ (MAX3902) CML OUT(MAX3902) DC CANCELLATION TTL Figure 2. Functional Diagram 8 _______________________________________________________________________________________ OUT_TTL (MAX3901) 150Mbps Automotive Fiber Optic Receiver VCC ROUT Status Monitor ROUT OUT+ VCC OUT- The MAX3901/MAX3902 include a status monitor (Figure 4). The average current at the FILT (Figure 5) pad determines whether the MAX3901/MAX3902 are in operating or standby mode. STATUS is TTL low when the receiver is in operating mode. STATUS is TTL high when the receiver is in standby mode. Applications Information Optical Power Relations Many of the MAX3901/MAX3902 specifications relate to the input signal amplitude. Figure 6 and Table 1 show relations that are helpful for converting optical power to input signal when designing with the MAX3901/ MAX3902. MAX3902 Wire Bonding Figure 3. MAX3902 CML Output VCC RSTATUS 16kΩ STATUS MAX3901 MAX3902 For high-current density and reliable operation, the MAX3901 and MAX3902 use gold metalization. For best results, use gold-wire ball-bonding techniques. Use caution if attempting wedge bonding. Bond-pad size is 94.4µm x 94.4µm, and bond-pad metal thickness is 1.2µm. Refer to Maxim Application Note, HFAN08.0.1: Understanding Bonding Coordinates and Physical Die Size for additional information. Table 1. Optical Power Relations* PARAMETER SYMBOL RELATION Average Power PAVE PAVE = (P0 + P1) / 2 Extinction Ratio Er 2PAVE + OMA 2PAVE − OMA Optical Power of a “1” P1 P1 = 2PAVE Optical Power of a “0” P0 P0 = 2PAVE / Er + 1 Er = P1 / P0 Figure 4. STATUS Monitor Output VCC 100kΩ Optical Modulation Amplitude MAX3901 MAX3902 FILT OMA Er Er + 1 E -1 OMA = P1 − P0 = 2PAVE r Er + 1 *Assuming a 50% average mark density. 35pF Figure 5. FILT pad _______________________________________________________________________________________ 9 MAX3901/MAX3902 The coupling capacitor should be 0.1µF or larger. Refer to Application Note HFAN-1.1: Choosing AC-Coupling Capacitors for a more detailed discussion. VCC Table 2 gives center pad coordinates for the MAX3901 and MAX3902 bond pads. Table 2. Bond-Pad Information P1 NAME PAD OPTICAL POWER MAX3901/MAX3902 150Mbps Automotive Fiber Optic Receiver PAVE P0 TIME Figure 6. Optical Power Relations Chip Information TRANSISTOR COUNT: 1175 PROCESS: Silicon Bipolar, CB30HM Die Thickness: 12 mils (300µm) COORDINATES (µm) MAX3901 MAX3902 X Y BP1 FILT FILT 51.0 1302.0 BP2 IN IN 51.0 1128.0 BP3 N.C. N.C. 51.0 825.0 BP4 N.C. N.C. 51.0 399.0 BP5 VCC VCC 51.0 225.0 BP6 VCC VCC 51.0 51.0 -30.0 BP7 VCC VCC 291.0 BP8 GND GND 918.0 -30.0 BP9 N.C. OUT+ 1140.0 -30.0 -30.0 BP10 N.C. OUT- 1359.0 BP11 STATUS STATUS 1548.0 -30.0 BP12 OUT_TTL N.C. 1581.0 279.0 BP13 N.C. N.C. 936.0 1338.0 BP14 N.C. N.C. 762.0 1338.0 BP15 N.C. N.C. 585.0 1338.0 BP16 GND GND 408.0 1338.0 BP17 GND GND 231.0 1338.0 Coordinate 0,0 is the lower left corner of the passivation opening for pad 6. Table 3. Typical Optical Receiver Performance RECEIVER CONFIGURATION PCS 850nm ρ = 0.5A/W MAX3901 Receiver POF 650nm ρ = 0.3A/W MAX3901 Receiver PCS 850nm ρ = 0.5A/W MAX3902 Receiver Worst-Case Sensitivity BER = 1E - 9 and STATUS = Low -26.2dBm OMA -27dBm -26.2dBm OMA Expected Typical Sensitivity -31.5dBm OMA -29dBm -30.5dBm OMA +3dBm OMA +5dBm +3dBm OMA -35dBm -37dBm -35dBm -32.5dBm -34.5dBm -32.5dBm OPTICAL PARAMETER Optical Overload Typical Input for Standby Mode Typical Input for Operating Mode 10 ______________________________________________________________________________________ 150Mbps Automotive Fiber Optic Receiver +3.3V SUPPLY FILTER OPTICAL RECEIVER VCC FILT STATUS 5kΩ 25Ω LVDS INPUT OUT+ IN MAX3902 100Ω OUT- 0.1µF 100Ω 0.1µF 25Ω GND 5kΩ ______________________________________________________________________________________ 11 MAX3901/MAX3902 Typical Operating Circuits (continued) 150Mbps Automotive Fiber Optic Receiver FILT 1 IN 2 N.C. 3 GND GND N.C. N.C. N.C. MAX3901/MAX3902 MAX3901 Chip Topography 17 16 15 14 13 1.65mm 65mils N.C. 4 6 VCC 7 8 9 10 N.C. VCC N.C. 5 GND 12 VCC 11 1.80mm 71mils 12 ______________________________________________________________________________________ OUT_TTL STATUS 150Mbps Automotive Fiber Optic Receiver 1 IN 2 N.C. 3 N.C. 15 N.C. 16 N.C. GND GND 17 FILT 14 13 1.63mm 64.17mils N.C. 4 5 VCC 6 GND 8 VCC (0, 0) 7 9 10 OUT- VCC OUT+ 12 11 N.C. STATUS 1.78mm 70.08mils Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © 2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. MAX3901/MAX3902 MAX3902 Chip Topography