ISL54504, ISL54505 ® Data Sheet August 29, 2007 FN6552.1 +1.8V to +5.5V, 2.5Ω, Single SPST Analog Switches Features The Intersil ISL54504 and ISL54505 devices are low ON-resistance, low voltage, bidirectional, single pole/single throw (SPST) analog switches designed to operate from a single +1.8V to +5.5V supply. Targeted applications include battery powered equipment that benefit from low rON resistance (2.5Ω), excellent rON flatness (0.6Ω), and fast switching speeds (tON = 25ns, tOFF = 15ns). The digital logic input is 1.8V CMOS compatible when using a single +3V supply. • rON flatness (+4.5V Supply) . . . . . . . . . . . . . . . . . . . . . . 0.6Ω Cell phones, for example, often face ASIC functionality limitations. The number of analog input or GPIO pins may be limited and digital geometries are not well suited to analog switch performance. This family of parts may be used to switch in additional functionality while reducing ASIC design risk. The ISL54054, ISL54055 are offered in a 6 Ld 1.2mmx1.0mmx0.4mm pitch µTDFN package, alleviating board space limitations. The ISL54504 has one normally open (NO) switch and ISL54505 has one normally closed (NC) switch. TABLE 1. FEATURES AT A GLANCE ISL54504 ISL54505 Number of Switches 1 1 SW NO NC 1.8V rON 6Ω 6Ω 1.8V tON/tOFF 65ns/40ns 65ns/40ns 3V rON 4Ω 4Ω 3V tON/tOFF 30ns/20ns 30ns/20ns 5V rON 2.5Ω 2.5Ω 5V tON/tOFF 25ns/15ns 25ns/15ns Package • ON-resistance (rON) - VCC = +5.0V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5Ω - VCC = +3.0V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0Ω - VCC = +1.8V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0Ω • Single supply operation . . . . . . . . . . . . . . . . . +1.8V to +5.5V • Fast switching action (+4.5V Supply) - tON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25ns - tOFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15ns • ESD HBM rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6kV • 1.8V CMOS logic compatible (+3V supply) • Available in 6 Ld µTDFN Package • Pb-free available (RoHS compliant) Applications • Battery powered, handheld, and portable equipment - Cellular/mobile phones - Pagers - Laptops, notebooks, palmtops • Portable Test and Measurement • Medical Equipment • Audio and video switching Related Literature • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” 6 Ld µTDFN 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2007. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL54504, ISL54505 Ordering Information PART NUMBER (Note) PART MARKING TEMP. RANGE (°C) PACKAGE (Pb-Free) PKG. DWG. # ISL54504IRUZ-T* 4 -40 to +85 6 Ld μTDFN (Tape and Reel) L6.1.2x1.0A ISL54505IRUZ-T* 5 -40 to +85 6 Ld μTDFN (Tape and Reel) L6.1.2x1.0A *Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. Pinouts (Note 1) ISL54505 (6 LD μTDFN) TOP VIEW ISL54504 (6 LD μTDFN) TOP VIEW NO 1 6 IN N.C. 1 6 IN GND 2 5 V+ GND 2 5 V+ N.C. 3 4 COM NC 3 4 COM NOTE: 1. Switches Shown for Logic “0” Input. Truth Table NOTE: Pin Descriptions LOGIC ISL54504 ISL54505 0 Off On 1 On Off Logic “0” ≤0.5V. Logic “1” ≥1.4V with a 3V supply. PIN NAME V+ System Power Supply Input (+1.8V to +5.5V) GND Ground Connection IN Digital Control Input COM 2 FUNCTION Analog Switch Common Pin NO Analog Switch Normally Open Pin NC Analog Switch Normally Closed Pin N.C. No Connect FN6552.1 August 29, 2007 ISL54504, ISL54505 Absolute Maximum Ratings Thermal Information V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 6.5V Input Voltages NO, NC, IN (Note 2). . . . . . . . . . . . . . . . . . . . -0.5V to ((V+) + 0.5V) Output Voltages COM (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to ((V+) + 0.5V) Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . . ±300mA Peak Current NO, NC, or COM (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . . ± 600mA ESD Rating Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>6kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>300V Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . .>1400V Thermal Resistance (Typical, Notes 3, 4) θJA (°C/W) θJC (°C/W) 6 Ld µTDFN Package . . . . . . . . . . . . . 239.2 111.6 Maximum Junction Temperature (Plastic Package). . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions V+ (Positive DC Supply Voltage) . . . . . . . . . . . . . . . . . 1.8V to 5.5V Analog Signal Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to V+ VIN (Digital Logic Input Voltage (IN) . . . . . . . . . . . . . . . . . 0V to V+ Temperature Range ISL54504IRUZ, ISL54505IRUZ . . . . . . . . . . . . . . -40°C to +85°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 2. Signals on NC, NO, IN, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings. 3. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 4. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications - 5V Supply PARAMETER Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.0V, VINL = 0.8V (Note 5), Unless Otherwise Specified TEST CONDITIONS TEMP (°C) MIN (Notes 6, 7) Full 0 - V+ V 25 - 2.2 2.5 Ω Full - - 3 Ω 25 - 0.6 0.65 Ω Full - - 0.7 Ω 25 -25 1.5 25 nA Full -150 - 150 nA TYP MAX (Notes 6, 7) UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG ON-Resistance, rON V+ = 4.5V, ICOM = 100mA, VNO or VNC = 0V to V+, (Note 9, See Figure 4) rON Flatness, rFLAT(ON) V+ = 4.5V, ICOM = 100mA, VNO or VNC = 0V to V+, (Notes 8, 9) NO or NC OFF Leakage Current, INO(OFF) or INC(OFF) V+ = 5.5V, VCOM = 0.3V, 5V, VNO or VNC = 5V, 0.3V COM ON Leakage Current, ICOM(ON) V+ = 5.5V, VCOM = 0.3V, 5V, or VNO or VNC = 0.3V, 5V, or Floating 25 -30 2.8 30 nA Full -300 - 300 nA V+ = 4.5V, VNO or VNC = 3.0V, RL = 50Ω, CL = 35pF (See Figure 1, Note 9) 25 - 25 - ns Full - 25 - ns V+ = 4.5V, VNO or VNC = 3.0V, RL = 50Ω, CL = 35pF (See Figure 1, Note 9) 25 - 15 - ns Full - 16 - ns Break-Before-Make Time Delay, tD V+ = 5.5V, VNO or VNC = 3.0V, RL = 50Ω, CL = 35pF (See Figure 3, Note 9) Full - 15 - ns DYNAMIC CHARACTERISTICS Turn-ON Time, tON Turn-OFF Time, tOFF Charge Injection, Q VG = 0V, RG = 0Ω, CL = 1.0nF (See Figure 2) 25 - 24 - pC OFF Isolation RL = 50Ω, CL = 5pF, f = 1MHz, VCOM = 1VP-P (See Figure 3) 25 - 70 - dB Total Harmonic Distortion f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 32Ω 25 - 0.15 - % Total Harmonic Distortion f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 600Ω 25 - 0.014 - % -3dB Bandwidth Signal = 0dBm, RL = 50Ω 25 - 250 - MHz NO or NC OFF Capacitance, COFF V+ = 4.5V, f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 5) 25 - 7 - pF COM ON Capacitance, CCOM(ON) V+ = 4.5V, f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 5) 25 - 18 - pF 3 FN6552.1 August 29, 2007 ISL54504, ISL54505 Electrical Specifications - 5V Supply PARAMETER Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.0V, VINL = 0.8V (Note 5), Unless Otherwise Specified (Continued) TEST CONDITIONS TEMP (°C) MIN (Notes 6, 7) Full 1.8 - 5.5 V 25 - 0.028 0.1 μA Full - 1.1 2.5 μA TYP MAX (Notes 6, 7) UNITS POWER SUPPLY CHARACTERISTICS Power Supply Range Positive Supply Current, I+ V+ = 5.5V, VIN = 0V or V+ DIGITAL INPUT CHARACTERISTICS Input Voltage Low, VINL Full - - 0.8 V Input Voltage High, VINH Full 2.4 - - V Full -0.1 0.053 0.1 μA Input Current, IINH, IINL V+ = 5.5V, VIN = 0V or V+ Electrical Specifications - 3V Supply PARAMETER Test Conditions: V+ = +2.7V to +3.6V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Note 5), Unless Otherwise Specified TEST CONDITIONS TEMP (°C) MIN (Notes 6, 7) TYP Full 0 - 25 - Full - MAX (Notes 6, 7) UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG ON-Resistance, rON rON Flatness, rFLAT(ON) V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+, (Note 9, See Figure 4) V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+, (Notes 7, 9) V+ V 3.3 3.5 Ω - 4.5 Ω 25 - 1 1.1 Ω Full - - 1.2 Ω DYNAMIC CHARACTERISTICS Turn-ON Time, tON V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF (See Figure 1, Note 9) 25 - 30 - ns Full - 30 - ns 25 - 20 - ns Turn-OFF Time, tOFF V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF (See Figure 1, Note 9) Full - 20 - ns Charge Injection, Q VG = 0V, RG = 0Ω,CL = 1.0nF (See Figure 2) 25 - 16 - pC OFF Isolation RL = 50Ω, CL = 5pF, f = 1MHz, VCOM = 1VP-P (See Figure 3) 25 - -70 - dB Total Harmonic Distortion f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 32Ω 25 - 0.36 - % Total Harmonic Distortion f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 600Ω 25 - 0.03 - % -3dB Bandwidth Signal = 0dBm, RL = 50Ω 25 - 250 - MHz NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 5) 25 - 6 - pF COM OFF Capacitance, CCOM(OFF) f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 5) 25 - 15 - pF COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 5) 25 - 18 - pF 25 - 0.013 - μA Full - 0.7 - μA Input Voltage Low, VINL Full - - 0.5 V Input Voltage High, VINH Full 1.4 - - V Full -0.1 0.058 0.1 μA POWER SUPPLY CHARACTERISTICS Positive Supply Current, I+ V+ = 3.6V, VIN = 0V or V+ DIGITAL INPUT CHARACTERISTICS Input Current, IINH, IINL V+ = 3.6V, VIN = 0V or V+ 4 FN6552.1 August 29, 2007 ISL54504, ISL54505 Electrical Specifications - 1.8V Supply PARAMETER Test Conditions: V+ = +1.8V, GND = 0V, VINH = 1V, VINL = 0.4V (Note 5), Unless Otherwise Specified TEST CONDITIONS TEMP (°C) MIN (Notes 6, 7) Full 0 - V+ V 25 - 6 6.5 Ω Full - - 7 Ω 25 - 65 - ns TYP MAX (Notes 6, 7) UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG ON-Resistance, rON V+ = 1.8V, ICOM = 10mA, VNO or VNC = 0V to V+ (Note 9, See Figure 4) DYNAMIC CHARACTERISTICS Turn-ON Time, tON V+ = 1.8V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF (See Figure 1, Note 9) Turn-OFF Time, tOFF V+ = 1.8V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF (See Figure 1, Note 9) VG = V+/2, RG = 0Ω, CL = 1.0nF (See Figure 2) Charge Injection, Q Full - 95 - ns 25 - 40 - ns Full - 65 - ns 25 - 8.2 - pC DIGITAL INPUT CHARACTERISTICS Input Voltage Low, VINL Full - - 0.4 V Input Voltage High, VINH Full 1 - - V NOTES: 5. VIN = input voltage to perform proper function. 6. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 7. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested. 8. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range. 9. Limits established by characterization and are not production tested. Test Circuits and Waveforms V+ LOGIC INPUT V+ tr < 20ns tf < 20ns 50% 0V tOFF SWITCH INPUT SWITCH INPUT VNO VOUT 90% SWITCH OUTPUT C VOUT NO OR NC COM IN 90% 0V LOGIC INPUT GND RL 50Ω CL 35pF tON Logic input waveform is inverted for switches that have the opposite logic sense. Repeat test for all switches. CL includes fixture and stray capacitance. RL --------------------------V OUT = V (NO or NC) R + r L ( ON ) FIGURE 1A. MEASUREMENT POINTS FIGURE 1B. TEST CIRCUIT FIGURE 1. SWITCHING TIMES 5 FN6552.1 August 29, 2007 ISL54504, ISL54505 Test Circuits and Waveforms (Continued) V+ SWITCH OUTPUT VOUT ΔVOUT RG C NO OR NC VOUT COM VINH ON ON LOGIC INPUT VG OFF GND IN CL VINL LOGIC INPUT Q = ΔVOUT x CL FIGURE 2A. MEASUREMENT POINTS FIGURE 2B. TEST CIRCUIT FIGURE 2. CHARGE INJECTION V+ C V+ rON = V1/I1 * C NO OR NC SIGNAL GENERATOR NO OR NC VNX IN IN V1 I1 0V OR V+ VINL OR VINH 100mA COM GND COM ANALYZER GND RL * I = 10mA AT V+ = 1.8V 1 FIGURE 4. rON TEST CIRCUIT FIGURE 3. OFF ISOLATION TEST CIRCUIT V+ C NO OR NC IN VINL OR VINH IMPEDANCE ANALYZER COM GND FIGURE 5. CAPACITANCE TEST CIRCUIT 6 FN6552.1 August 29, 2007 ISL54504, ISL54505 Detailed Description Supply Sequencing And Overvoltage Protection The ISL54504 and ISL54505 are bidirectional, single pole/single throw (SPST) analog switches. They offer precise switching capability from a single 1.8V to 5.5V supply with low ON-resistance (2.5Ω) and high speed operation (tON = 25ns, tOFF = 15ns). The devices are especially well suited for portable battery powered equipment due to their low operating supply voltage (1.8V), low power consumption (0.15µW), low leakage currents (300nA max) and tiny µTDFN package. With any CMOS device, proper power supply sequencing is required to protect the device from excessive input currents, which might permanently damage the IC. All I/O pins contain ESD protection diodes from the pin to V+ and to GND (see Figure 7). To prevent forward biasing these diodes, V+ must be applied before any input signals, and the input signal voltages must remain between V+ and GND. The ISL54504 is a single normally open (NO) SPST analog switch. The ISL54505 is a single normally closed (NC) SPST analog switch. External V+ Series Resistor For improved ESD and latch-up immunity, Intersil recommends adding a 100Ω resistor in series with the V+ power supply pin of the ISL54050 IC (see Figure 6). During an overvoltage transient event (such as occurs during system level IEC 61000 ESD testing), substrate currents can be generated in the IC that can trigger parasitic SCR structures to turn ON, creating a low impedance path from the V+ power supply to ground. This will result in a significant amount of current flow in the IC, which can potentially create a latch-up state or permanently damage the IC. The external V+ resistor limits the current during this over-stress situation and has been found to prevent latch-up or destructive damage for many overvoltage transient events. Under normal operation the sub-microamp IDD current of the IC produces an insignificant voltage drop across the 100Ω series resistor resulting in no impact to switch operation or performance. V+ OPTIONAL PROTECTION RESISTOR If these conditions cannot be guaranteed then precautions must be implemented to prohibit the current and voltage at the logic pin and signal pins from exceeding the maximum ratings of the switch. The following two methods can be used to provide additional protection to limit the current in the event that the voltage at a signal pin or logic pin goes below ground or above the V+ rail. Logic inputs can easily be protected by adding a 1kΩ resistor in series with the input (see Figure 7). The resistor limits the input current below the threshold that produces permanent damage and the sub-microamp input current produces an insignificant voltage drop during normal operation. This method is not acceptable for the signal path inputs. Adding a series resistor to the switch input defeats the purpose of using a low rON switch. Connecting Schottky diodes to the signal pins (as shown in Figure 7) will shunt the fault current to the supply or to ground, thereby protecting the switch. These Schottky diodes must be sized to handle the expected fault current. OPTIONAL SCHOTTKY DIODE V+ OPTIONAL PROTECTION RESISTOR C INX VNX VCOM 100Ω GND NO COM NC OPTIONAL SCHOTTKY DIODE IN FIGURE 7. OVERVOLTAGE PROTECTION GND Power-Supply Considerations FIGURE 6. V+ SERIES RESISTOR FOR ENHANCED ESD AND LATCH-UP IMMUNITY 7 The ISL54504/ISL54505 construction is typical of most single supply CMOS analog switches in that they have two supply pins: V+ and GND. V+ and GND drive the internal CMOS switches and set their analog voltage limits. Unlike switches with a 4V maximum supply voltage, the ISL54504/ISL54505 5.5V maximum supply voltage provides plenty of room for the 10% tolerance of 3.6V supplies, as well as room for overshoot and noise spikes. FN6552.1 August 29, 2007 ISL54504, ISL54505 The minimum recommended supply voltage is 1.8V but the part will operate with a supply below 1.8V. It is important to note that the input signal range, switching times, and ON-resistance degrade at lower supply voltages. Refer to the “Electrical Specifications” tables starting on page 3 and the “Typical Performance Curves” starting on page 8 for details. V+ and GND also power the internal logic and level shiftier. The level shiftier converts the input logic levels to switched V+ and GND signals to drive the analog switch gate terminals. An OFF switch behaves like a capacitor and passes higher frequencies with less attenuation, resulting in signal feedthrough from a switch’s input to output. Off isolation is the resistance of this signal feedthrough. Figure 16 details the high off isolation provided by the ISL54504/ISL54505. At 1MHz, off isolation is about 70dB in 50Ω systems, decreasing approximately 20dB per decade as frequency increases. Higher load impedances decrease off isolation due to the voltage divider action of the switch OFF impedance and the load impedance. Leakage Considerations Reverse ESD protection diodes are internally connected between each analog-signal pin and both V+ and GND. One of these diodes conducts if any analog signal exceeds V+ or GND. This family of switches cannot be operated with bipolar supplies because the input switching point becomes negative in this configuration. Logic-Level Thresholds This switch family is 1.8V CMOS compatible (0.5V and 1.4V) over a supply range of 2V to 3.6V (see Figure 14). At 3.6V the VIH level is about 0.95V. This is still below the 1.8V CMOS guaranteed high output minimum level of 1.4V, but noise margin is reduced. The digital input stages draw supply current whenever the digital input voltage is not at one of the supply rails. Driving the digital input signals from GND to V+ with a fast transition time minimizes power dissipation. High-Frequency Performance In 50Ω systems, the ISL54504/ISL54505 has a -3dB bandwidth of 250MHz (see Figure 15). The frequency response is very consistent over a wide V+ range and for varying analog signal levels. Virtually all the analog leakage current comes from the ESD diodes to V+ or GND. Although the ESD diodes on a given signal pin are identical and therefore fairly well balanced, they are reverse biased differently. Each is biased by either V+ or GND and the analog signal. This means their leakages will vary as the signal varies. The difference in the two diode leakages to the V+ and GND pins constitutes the analogsignal-path leakage current. All analog leakage current flows between each pin and one of the supply terminals, not to the other switch terminal. This is why both sides of a given switch can show leakage currents of the same or opposite polarity. There is no connection between the analog signal paths and V+ or GND. Typical Performance Curves TA = +25°C, Unless Otherwise Specified. 4.0 3.0 ICOM = 100mA 3.5 2.5 V+ = 2.7V 3.0 +85°C 2.0 rON (Ω) 2.5 rON (Ω) 2.0 V+ = 3V V+ = 4.5V 1.5 +25°C 1.5 -40°C 1.0 V+ = 5V 1.0 V+ = 4.5V ICOM = 100mA 0.5 0.5 0.0 0.0 0 1 2 3 4 VCOM (V) FIGURE 8. ON-RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE 8 5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 VCOM (V) FIGURE 9. ON-RESISTANCE vs SWITCH VOLTAGE FN6552.1 August 29, 2007 ISL54504, ISL54505 Typical Performance Curves TA = +25°C, Unless Otherwise Specified. (Continued) 5.0 8 V+ = 2.7V ICOM = 100mA 4.5 7 4.0 6 +85°C +85°C 3.0 rON (Ω) rON (Ω) 3.5 +25°C 2.5 5 +25°C 4 -40°C -40°C 3 2.0 2 1.5 1.0 V+ = 1.8V ICOM = 10mA 0 0.5 1.0 1.5 2.0 1 2.5 0 0.2 0.4 0.6 0.8 1.0 1.2 VCOM (V) VCOM (V) FIGURE 10. ON-RESISTANCE vs SWITCH VOLTAGE 1.4 1.6 1.8 2.0 FIGURE 11. ON-RESISTANCE vs SWITCH VOLTAGE 100 70 -40°C -40°C 90 60 80 70 50 +25°C tOFF (ns) tON (ns) 60 50 40 +85°C 40 +25°C 30 +85°C 30 20 20 10 10 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 0 6.0 1.5 2.0 2.5 3.0 V+ (V) FIGURE 12. TURN-ON TIME vs SUPPLY VOLTAGE 3.5 4.0 V+ (V) 4.5 5.0 5.5 6.0 FIGURE 13. TURN-OFF TIME vs SUPPLY VOLTAGE 1.4 0 -1 -2 1.2 NORMALIZED GAIN (dB) VINH AND VINL (V) -3 1.0 VINH 0.8 VINL 0.6 V+ = 1.8V TO 5.5V VCOM = 1VP-P -4 -5 -6 -7 -8 -9 -10 0.4 -11 -12 0.2 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 V+ (V) FIGURE 14. DIGITAL SWITCHING POINT vs SUPPLY VOLTAGE 9 -13 100k 1M 10M 100M 1G FREQUENCY (Hz) FIGURE 15. FREQUENCY RESPONSE FN6552.1 August 29, 2007 ISL54504, ISL54505 Typical Performance Curves TA = +25°C, Unless Otherwise Specified. (Continued) 25 -20 -30 V+ = 1.8V TO 5.5V 20 -40 15 -50 10 Q (pC) (dB) -60 -70 5 0 V+ = 5V -80 -5 -90 V+ = 1.8V -10 -100 -15 -110 -120 1k V+ = 3.3V 10k 100k 1M 10M FREQUENCY (Hz) FIGURE 16. OFF ISOLATION 100M 1G -20 0.0 0.5 1.0 1.5 2.0 2.5 3.0 VCOM (V) 3.5 4.0 4.5 5.0 FIGURE 17. CHARGE INJECTION vs SWITCH VOLTAGE Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND TRANSISTOR COUNT: PROCESS: Submicron CMOS 10 FN6552.1 August 29, 2007 ISL54504, ISL54505 Ultra Thin Dual Flat No-Lead Plastic Package (UTDFN) A E L6.1.2x1.0A B 6 LEAD ULTRA THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE MILLIMETERS PIN 1 REFERENCE 2X 0.10 C 2X D 0.10 C SYMBOL MIN NOMINAL MAX NOTES A 0.45 0.50 0.55 - A1 - - 0.05 - A 0.08 C 0.15 0.20 0.25 5 D 0.95 1.00 1.05 - E 1.15 1.20 1.25 - 0.40 BSC e A1 A3 SIDE VIEW C SEATING PLANE 4X e DETAIL B 1 5X L 3 - b DETAIL A 0.10 C 7X 0.127 REF A3 TOP VIEW - L 0.30 0.35 0.40 - L1 0.40 0.45 0.50 - N 6 2 Ne 3 3 θ 0 - 12 4 L1 Rev. 2 8/06 NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 6 4 BOTTOM VIEW b 6X 0.10 C A B 0.05 C NOTE 3 2. N is the number of terminals. 3. Ne refers to the number of terminals on E side. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 0.1x45° CHAMFER 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Maximum package warpage is 0.05mm. 8. Maximum allowable burrs is 0.076mm in all directions. 9. JEDEC Reference MO-255. A3 A1 DETAIL A DETAIL B PIN 1 LEAD 10. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. 1.00 1.40 0.20 0.30 0.45 0.35 0.20 0.40 LAND PATTERN 10 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11 FN6552.1 August 29, 2007