Part Number 855737 70 MHz SAW Filter Data Sheet Features • • • • • • • For broadband applications Typical 3dB bandwidth of 1 MHz High attenuation Single-ended operation Ceramic Surface Mount Package (SMP) Replaces Sawtek P/N 851544 (BW 3dB=1 MHz) Package Pin Configuration Surface Mount 24.60 x 9.00 x 2.31 mm Bottom View 1 2 3 4 5 2.31 NOM. 2.62 MAX. 10 9 8 7 6 1.02 24.6 1.91 1.80 R0.5 9.00 2.31 3.53 x 4.83 1.02 Pin No. 1 5 6 10 2,3,4 7,8,9 Description Input return Output Output return Input Case Ground Case Ground Dimensions shown are nominal in millimeters All tolerances are ±0.15mm except overall length ±0.20mm and width +0.13/-0.20mm Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 0.5 - 1.0µm, over a 2 - 6µm Ni plating Subject to change or obsolescence without notice Rev A 27-Jun-2002 Page 1 of 5 Part Number 855737 70 MHz SAW Filter Data Sheet Electrical Specifications (1) Operating Temperature Range: (2) 0 to +70 oC Parameter (3) Minimum Typical Maximum Unit 70.46 70.59 68.91 - 70 22.2 69.47 70.50 69.37 70.62 68.95 71.06 23 69.54 69.41 71.09 MHz dB MHz MHz MHz MHz MHz MHz - 0.55 1 dB p-p - 2.2 5 deg p-p - 100 190 nsec 48 40 40 50 35 36 50 - 53 45 45 55 37 40 65 50 50 Quartz - dB dB dB dB dB dB dB Ω Ω - Center Frequency Minimum Insertion Loss Lower 1 dB Bandedge (4) Upper 1 dB Bandedge Lower 3 dB Bandedge (4) Upper 3 dB Bandedge Lower 40 dB Bandedge (4) Upper 40 dB Bandedge Amplitude Variation 69.54 - 70.46 MHz Phase Linearity 69.54 - 70.46 MHz Group Delay Variation 69.54 - 70.46 MHz Relative Attenuation (4) 10 - 68.5 MHz 68.5 - 68.91 MHz 71.09 - 75 MHz 75 - 110 MHz 110 - 122 MHz 122 - 135 MHz 135 - 200 MHz Source Impedance (5) Load Impedance (5) Substrate Material Notes: 1. 2. 3. 4. 5. All specifications are based on the test circuit shown below In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances All attenuation measurements are measured relative to minimum insertion loss This is the optimum impedance in order to achieve the performance shown Test Circuit: Actual matching values may vary due to PCB layout and parasitics 220nH 50 Ω Single-ended 50Ω Subject to change or obsolescence without notice 7pF 820nH 10 5 50Ω 1,2,3,4 6,7,8,9 Rev A 27-Jun-2002 Page 2 of 5 Part Number 855737 70 MHz SAW Filter Data Sheet Typical Performance (at +25oC) Subject to change or obsolescence without notice Rev A 27-Jun-2002 Page 3 of 5 Part Number 855737 70 MHz SAW Filter Data Sheet Matching Schematic 220nH 50 Ω Single-ended 50Ω 7pF 820nH 10 5 50Ω 1,2,3,4 6,7,8,9 Marking PCB Footprint 8.84 SAWTEK 855737 XXXXXX 9.19 Date code ID dot 1.95 Date code is the day of the current year in Julian format, last digit of the year, and hour of the day .69 1.22 This footprint represents a recommendation only Dimensions shown are nominal in millimeters Tape and Reel 2.7 44.8 0.36 Ø330 4.0 2.0 ID dot Ø1.5 A 1.75 20.2 40.4 44.0 25.6 Ø102 Ø20.2 Ø13.0 2.0 Direction of travel 0.20 2.6 Section A-A 9.39 12.0 R0.75 Ø1.5 A Dimensions shown are nominal in millimeters Packaging quantity: 1000 units/reel Subject to change or obsolescence without notice Rev A 27-Jun-2002 Page 4 of 5 Part Number 855737 70 MHz SAW Filter Data Sheet Maximum Ratings Parameter Operating Temperature Range Storage Temperature Range Symbol Minimum Maximum T Tstg 0 -40 +70 +85 Unit o C C o Warnings • • Electrostatic Sensitive Device (ESD) Avoid ultrasonic exposure Links to Additional Technical Information PCB Layout Tips Qualification Flowchart Soldering Profile S-Parameters Other Technical Information Contact Information PO Box 609501 Orlando, FL 32860-9501 USA Subject to change or obsolescence without notice Or contact one of our worldwide network of sales offices, representatives or distributors Phone: +1 (407) 886-8860 Fax: +1 (407) 886-7061 Email: [email protected] Web: www.sawtek.com Rev A 27-Jun-2002 Page 5 of 5