MAXIM MAX394C/D

19-0391; Rev 0; 5/95
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
____________________________Features
The MAX394 is a precision, low-voltage, quad, singlepole/double-throw (SPDT) analog switch. The four independent switches operate with bipolar supplies ranging
from ±2.7V to ±8V, or with a single supply of +2.7V to
+15V. The MAX394 offers low on-resistance (less than
35Ω), guaranteed to match within 2Ω between channels
and to remain flat over the analog signal range (∆4Ω
max). It also offers break-before-make switching (10ns
typical), with turn-off times less than 75ns and turn-on
times less than 130ns. The MAX394 is ideal for portable
operation since quiescent current runs less than 1µA with
all inputs high or low.
♦ Low On-Resistance, < 17Ω Typical (35Ω max)
♦ Guaranteed Matched On-Resistance Between
Channels, < 2Ω
♦ Guaranteed Flat On-Resistance over Analog
Signal Range, ∆4Ω Max
♦ Guaranteed Charge Injection < 10pC
♦ Guaranteed Off-Channel Leakage < 2.5nA at +85°C
♦ ESD Guaranteed > 2000V per Method 3015.7
♦ Single-Supply Operation (+2.7V to +15V)
Bipolar-Supply Operation (±2.7V to ±8V)
♦ TTL/CMOS-Logic Compatibility
♦ Rail-to-Rail Analog Signal Handling Capability
♦ Pin Compatible with MAX333, MAX333A
This monolithic, quad switch is fabricated with Maxim’s
low voltage silicon-gate process. Design improvements
guarantee extremely low charge injection (10pC), low
power consumption (10µW), and electrostatic discharge
(ESD) greater than 2000V.
Logic inputs are TTL and CMOS compatible and guaranteed over a +0.8V to +2.4V range for supply voltages up
to +8V. When supplies exceed +8V, the inputs are typically +0.8V to +4V. Logic inputs and switched analog signals can range anywhere between the supply voltages
without damage.
________________________Applications
Test Equipment
Communications Systems
PBX, PABX
Heads-Up Displays
Portable Instruments
Audio Signal Routing
Set-Top Boxes
______________Ordering Information
PART
TEMP. RANGE
0°C to +70°C
20 Plastic DIP
MAX394CWP
MAX394C/D
MAX394EPP
MAX394EWP
MAX394MJP
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-55°C to +125°C
20 Wide SO
Dice*
20 Plastic DIP
20 Wide SO
20 CERDIP**
* Contact factory for dice specifications.
** Contact factory for availability.
__________Typical Operating Circuit
OUTPUTS
INPUTS
__________________Pin Configuration
TOP VIEW
PIN-PACKAGE
MAX394CPP
V1
V1 - V2
V2
IN1 1
20 IN4
NO1 2
19 NO4
COM1 3
18 COM4
NC1 4
17 NC4
V- 5
GND 6
OSC
IN
16 V+
MAX394
NC2 7
15 N.C.
14 NC3
COM2 8
13 COM3
NO2 9
12 NO3
IN2 10
11 IN3
DIP/SO
SWITCHES ARE SHOWN WITH LOGIC "0" INPUT
N.C. = NOT INTERNALLY CONNECTED
V3 - V4
V3
V4
FLYING CAPACITOR
LEVEL TRANSLATOR
(2-CHANNEL)
________________________________________________________________ Maxim Integrated Products
Call toll free 1-800-998-8800 for free samples or literature.
1
MAX394
_______________General Description
MAX394
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
ABSOLUTE MAXIMUM RATINGS
Voltage Referenced to GND
V+ .......................................................................-0.3V to +17V
V- ........................................................................+0.3V to -17V
V+ to V-...............................................................-0.3V to +17V
COM_, NO_, NC_, IN_ (Note 1) ..................(V- - 2V) to (V+ + 2V)
or 30mA, whichever occurs first
Continuous Current, Any Pin...............................................30mA
Peak Current, Any Pin
(pulsed at 1ms, 10% duty cycle max) ..........................100mA
Continuous Power Dissipation (TA = +70°C)
Plastic DIP (derate 10.53mW/°C above+70°C) ...........842mW
Narrow SO (derate 8.70mW/°C above +70°C) ............696mW
CERDIP (derate 10.00mW/°C above +70°C) ...............800mW
Operating Temperature Ranges
MAX394C_ P .......................................................0°C to +70°C
MAX394E_ P ....................................................-40°C to +85°C
MAX394MJP ..................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Note 1: Signals on NC, NO, COM, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to
maximum current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Dual Supplies
(V+ = 5V ±10%, V- = -5V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
TEMP.
RANGE
CONDITIONS
MIN
TYP
(Note 2)
MAX
UNITS
SWITCH
Analog Signal Range
On-Resistance
On-Resistance Match Between
Channels (Note 4)
On-Resistance Flatness
(Note 4)
NC or NO Off Leakage Current
(Note 5)
COM Leakage Current
(Note 5)
2
VCOM,
VNO,
VNC
RON
∆RON
(Note 3)
V+ = 4.5V, V- = -4.5V,
VNC or VNO = ±3.5V,
ICOM = 10mA,
VINH = 2.4V,
VINL = 0.8V
VNC or VNO = ±3V,
ICOM = 10mA,
V+ = 5V, V- = -5V
VNC or VNO = 3V, 0V,
RFLAT(ON) -3V; ICOM = 10mA,
V+ = 5V; V- = -5V
INC(OFF)
or
INO(OFF)
ICOM(ON)
VCOM = ±4.5V,
VNC or VNO = ±4.5V,
V+ = 5.5V,V- = -5.5V
VCOM = ±4.5V,
VNC or VNO = ±4.5V,
V+ = 5.5V, V- = -5.5V
VTA =
+25°C
V+
C, E
20
35
M
20
30
TA = TMIN
C, E, M
to TMAX
TA =
+25°C
TA = TMIN
to TMAX
TA =
+25°C
TA = TMIN
to TMAX
TA =
+25°C
C, E, M
0.5
2
C, E, M
4
C, E, M
4
C, E, M
6
C, E
-0.2
-0.01
0.2
M
-0.1
-0.01
0.1
-2.5
2.5
-20
20
C, E
-0.4
-0.04
0.4
M
-0.2
-0.04
0.2
TA = TMIN C, E
to TMAX
M
Ω
45
TA = TMIN C, E
to TMAX
M
TA =
+25°C
V
-5.0
5.0
-20
20
_______________________________________________________________________________________
Ω
Ω
nA
nA
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
(V+ = 5V ±10%, V- = -5V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
(Note 2)
MAX
UNITS
DIGITAL LOGIC INPUT
Input Current with Input
Voltage High
IINH
VIN = 2.4V, all others = 0.8V
-1.0
0.005
1.0
µA
Input Current with Input
Voltage Low
IINL
VIN = 0.8V, all others = 2.4V
-1.0
0.005
1.0
µA
Logic High Input Voltage
VA_H
TA = TMIN to TMAX
Logic Low Input Voltage
VA_L
TA = TMIN to TMAX
2.4
V
0.8
V
DYNAMIC
Turn-On Time
tON
VCOM = 3V, Figure 2
Turn-Off Time
tOFF
VCOM = 3V, Figure 2
Break-Before-Make
Time Delay (Note 3)
tD
82
TA = +25°C
TA = TMIN to TMAX
130
175
TA = +25°C
57
TA = TMIN to TMAX
75
100
TA = +25°C
CL = 1.0nF, VGEN = 0V,
RGEN = 0Ω, Figure 6
TA = +25°C
5
TA = +25°C
66
dBm
TA = +25°C
88
dBm
f = 1MHz, Figure 3
TA = +25°C
12
pF
CCOM(OFF) f = 1MHz, Figure 3
TA = +25°C
12
pF
Channel On Capacitance CCOM(ON) f = 1MHz, Figure 4
TA = +25°C
39
pF
VCTE
Off Isolation (Note 6)
VISO
Crosstalk (Note 7)
VCT
Off Capacitance
COFF
COM Off Capacitance
RL = 50Ω, CL = 5pF,
f = 1MHz, Figure 3
RL = 50Ω, CL = 5pF,
f = 1MHz, Figure 8
10
ns
Figure 5
Charge Injection
(Note 3)
2
ns
ns
10
pC
SUPPLY
Power-Supply Range
±2.4
±8
V
Positive Supply Current
I+
All channels on or off,
V+ = 5.5V, V- = -5.5V, VIN = 0V or V+
-1.0
0.06
1.0
µA
Negative Supply
Current
I-
All channels on or off,
V+ = 5.5V, V- = -5.5V, VIN = 0V or V+
-1.0
-0.01
1.0
µA
_______________________________________________________________________________________
3
MAX394
ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)
MAX394
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
ELECTRICAL CHARACTERISTICS—Single +5V Supply
(V+ = 5V ±10%, V- = 0V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
TEMP.
RANGE
CONDITIONS
MIN
TYP
(Note 2)
MAX
UNITS
SWITCH
Analog Signal Range
On-Resistance
On-Resistance Match
Between Channels (Note 4)
On-Resistance Flatness
(Note 4)
NC or NO Off Leakage
Current (Note 8)
COM Leakage Current
(Note 8)
VCOM,
VNO,
VNC
RON
∆RON
(Note 3)
V+ = 5.0V, V- = 0V,
VNC or VNO = 3.5V,
ICOM = 1.0mA,
VINH = 2.4V,
VINL = 0.8V
VNC or VNO = 3V,
ICOM = 1.0mA,
V+ = 5V
VNC or VNO = 3V, 2V,
RFLAT(ON) 1V; ICOM = 1.0mA;
V+ = 5V; V- = 0V
INC(OFF)
or
INO(OFF)
ICOM(ON)
VCOM = 0V,
VNC or VNO = 4.5V,
V+ = 5.5V, V- = 0V
VCOM = 4.5V,
VNC or VNO = 4.5V,
V+ = 5.5V, V- = 0V
0V
TA = +25°C
TA = TMIN
to TMAX
C, E
25
60
C, E, M
75
0.5
Ω
4
TA = +25°C C, E, M
6
TA = TMIN
to TMAX
8
TA = TMIN
to TMAX
TA = +25°C
TA = TMIN
to TMAX
Ω
2
C, E, M
TA = +25°C
V
65
M
TA = +25°C C, E, M
TA = TMIN
to TMAX
V+
Ω
C, E, M
C, E
-0.2
-0.01
0.2
M
-0.1
-0.01
0.1
C, E
-2.5
2.5
M
-20
C, E
-0.4
-0.04
0.4
M
-0.2
-0.04
0.2
C, E
-5.0
5.0
M
-20
20
nA
20
nA
DIGITAL LOGIC INPUT
Input Current with Input
Voltage High
IINH
VIN = 2.4V, all others = 0.8V
-1.0
0.005
1.0
µA
Input Current with Input
Voltage Low
IINL
VIN = 0.8V, all others = 2.4V
-1.0
0.005
1.0
µA
4
_______________________________________________________________________________________
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
MAX394
ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued)
(V+ = +5V ±10%, V- = 0V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
MIN
CONDITIONS
TYP
(Note 2)
MAX
UNITS
DYNAMIC
Turn-On Time (Note 3)
tON
VCOM = 3V, Figure 2
Turn-Off Time (Note 3)
tOFF
VCOM = 3V, Figure 2
Break-Before-Make Time
Delay (Note 3)
Charge Injection
(Note 3)
TA = +25°C
60
TA = TMIN to TMAX
TA = +25°C
CL = 1.0nF, VGEN = 0V,
RGEN = 0Ω
250
300
TA = +25°C
tD
VCTE
160
TA = TMIN to TMAX
125
175
5
TA = +25°C
20
3
ns
ns
ns
5
pC
16
V
SUPPLY
Power-Supply Range
V+
2.4
Positive Supply Current
I+
All channels on or off, VIN = 0V or V+,
V+ = 5.5V, V- = 0V
Negative Supply Current
I-
All channels on or off, VIN = 0V or V+,
V+ = 5.5V, V- = 0V
-1.0
0.01
1.0
µA
-1.0
-0.01
1.0
µA
TYP
(Note 2)
MAX
ELECTRICAL CHARACTERISTICS—Single +3.3V Supply
(V+ = 3.0V to 3.6V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
TEMP.
RANGE
CONDITIONS
MIN
UNITS
SWITCH
Analog Signal Range
On-Resistance
VCOM,
VNO,
VNC
RON
NC or NO Off Leakage
Current (Note 8)
COM Leakage Current
(Note 8)
INC(OFF)
or
INO(OFF)
ICOM(ON)
(Note 3)
V+ = 3V, V- = 0V,
VNC or VNO = 1.5V,
ICOM = 1.0mA,
VINH = 2.4V,
VINL = 0.8V
VCOM = 0V,
VNC or VNO = 3V,
V+ = 3.6V, V- = 0V
VCOM = 3V,
VNC or VNO = 3V,
V+ = 3.6V, V- = 0V
0
TA = +25°C
TA = TMIN
to TMAX
TA = +25°C
TA = TMIN
to TMAX
TA = +25°C
TA = TMIN
to TMAX
C, E
V+
75
V
185
M
175
C, E, M
250
C, E
-0.2
-0.01
0.2
M
-0.1
-0.01
0.1
C, E
-2.5
M
-5.0
C, E
-0.4
-0.04
0.4
M
-0.2
-0.04
0.2
C, E
-5.0
5.0
M
-20.0
20.0
2.5
Ω
nA
5.0
nA
_______________________________________________________________________________________
5
MAX394
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
ELECTRICAL CHARACTERISTICS—Single +3.3V Supply (continued)
(V+ = 3.0V to 3.6V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
(Note 2)
MAX
UNITS
DIGITAL LOGIC INPUT
Input Current with Input
Voltage High
IINH
VIN = 2.4V, all others = 0.8V
-1.0
0.005
1.0
µA
Input Current with Input
Voltage Low
IINL
VIN = 0.8V, all others = 2.4V
-1.0
0.005
1.0
µA
Turn-On Time (Note 3)
tON
VCOM = 1.5V, Figure 2
TA = +25°C
400
ns
Turn-Off Time (Note 3)
tOFF
VCOM = 1.5V, Figure 2
TA = +25°C
150
ns
Figure 5
TA = +25°C
CL = 1.0nF, VGEN = 0V,
RGEN = 0Ω, Figure 6
TA = +25°C
DYNAMIC
Break-Before-Make Delay
(Note 3)
tD
Charge Injection (Note 3)
VCTE
5
20
1
ns
5
pC
16
V
SUPPLY
Power-Supply Range
V+
Positive Supply Current
I+
All channels on or off, VIN = 0V or V+,
V+ = 3.6V, V- = 0V
-1.0
0.01
1.0
µA
Negative Supply Current
I-
All channels on or off, VIN = 0V or V+,
V+ = 3.6V, V- = 0V
-1.0
-0.01
1.0
µA
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
6
2.7
The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Guaranteed by design.
∆RON = ∆RON(max) - ∆RON(min). On-resistance match between channels and flatness are guaranteed only with
specified voltages. Flatness is defined as the difference between the maximum and minimum value of on-resistance as
measured over the specified analog signal range.
Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temperature.
See Figure 6. Off isolation = 20log10 VCOM/VNC or VNO, VCOM = output, VNC or NO = input to off switch.
Between any two switches. See Figure 3.
Leakage testing at single supply is guaranteed by testing with dual supplies.
_______________________________________________________________________________________
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
ON-RESISTANCE vs. VCOM
(SINGLE SUPPLY)
30
50
MAX394-02
100
MAX394-01
35
ON-RESISTANCE vs. VCOM
OVER TEMPERATURE (DUAL SUPPLIES)
90
20
15
V+ = 5V, V- = -5V
RON (Ω)
70
RON (Ω)
RON (Ω)
V+ = 3V, V- = -3V
V+ = +5V
V- = -5V
40
80
25
MAX394-03
ON-RESISTANCE vs. VCOM
(DUAL SUPPLIES)
V+ = 3V, V- = 0V
60
50
30
+125°C
20
+85°C
40
10
V+ = 8V, V- = -8V
30
5
10
0
-8
-6
-4
-2
0
2
4
6
0
0
8
1
2
3
4
5
6
-5
-4
-3
-2 -1
0
1
2
3
VCOM (V)
VCOM (V)
VCOM (V)
ON-RESISTANCE vs. VCOM
OVER TEMPERATURE (SINGLE SUPPLY)
OFF LEAKAGE CURRENT
vs. TEMPERATURE
ON LEAKAGE CURRENT
vs. TEMPERATURE
100
40
OFF LEAKAGE (pA)
+85°C
+25°C
30
20
V+ = 5.5V
V- = -5.5V
VNC or VNO = ±4.5V
10
ICOM(OFF)
1
0.1
0.01
INC(OFF) or INO(OFF)
10
1
2
3
VCOM (V)
4
5
6
1000
100
V+ = 5.5V
V- = -5.5V
VCOM = ±4.5V
10
ICOM(ON)
1
0.1
0.01
INC (OFF) or INO(ON)
0.0001
0.0001
0
5
0.001
0.001
0
4
MAX394-06
1000
OFF LEAKAGE (pA)
+125°C
MAX394-05
V+ = 5V
V- = 0V
MAX394-04
50
RON (Ω)
V+ = 5V, V- = 0V
20
+25°C
10
-75 -50 -25
0
25
50
TEMPERATURE (°C)
75 100 125
-75 -50 -25
0
25
50
75 100 125
TEMPERATURE (°C)
_______________________________________________________________________________________
7
MAX394
__________________________________________Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
____________________________Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted).
CHARGE INJECTION
vs. VCOM
SUPPLY CURRENT vs.
TEMPERATURE
40
SUPPLY CURRENT (µA)
20
10
V+ = 3V, V- = 0V
0
-10
-20
V+ = 5V, V- = 0V
V+ = 5V, V- = -5V
V+ = 5.5V
V- = -5.5V
10
30
MAX394-08
100
MAX394-07
50
Q (pC)
1
I+ or I-
0.1
0.01
0.001
-30
0.0001
-40
-50
0.00001
-5
-4 -3
-2
-1
0
1
2
3
4
-75 -50 -25
5
VCOM (V)
0
25
50
75 100 125
TEMPERATURE (°C)
OFF-ISOLATION vs. FREQUENCY
CIRCUIT OF FIGURE 7
VIN = 0dBm
-20
VISO (dBm)
MAX394-09
0
-40
-60
-80
-100
0.1k
1k
10k
100k
1M
10M
100M
10M
100M
FREQUENCY (Hz)
CROSSTALK vs. FREQUENCY
MAX394-10
0
CIRCUIT OF FIGURE 8
VIN = 0dBm,
RL = 50Ω
-20
VCT (dBm)
MAX394
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
-40
-60
-80
-100
0.1k
1k
10k
100k
1M
FREQUENCY (Hz)
8
_______________________________________________________________________________________
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
PIN
NAME
FUNCTION
1, 10, 11, 20
IN1–IN4
Logic-Level Inputs
MAX394
_____________________Pin Description
+5V
D1
V+
2, 9, 12, 19
NO1–NO4
Normally Open Switches
MAX394
3, 8, 13, 18
COM1–COM4
4, 7,14, 17
NC1–NC4
Common Switch Poles
Normally Closed Switches
5
V-
Negative Power Supply
6
GND
Ground
15
N.C.
Not Internally Connected
16
V+
*
*
*
*
NO or NC
COM
VD2
Positive Power Supply
-5V
* INTERNAL PROTECTION DIODES
__________Applications Information
Operation with Supply Voltages
Other than ±5V
The MAX394 switch operates with ±2.7V to ±8V bipolar
supplies and a +2.7V to +15V single supply. In either
case, analog signals ranging from V+ to V- can be
switched. The Typical Operating Characteristics graphs
show the typical on-resistance variation with analog signal
and supply voltage. The usual on-resistance temperature
coefficient is 0.5%/°C (typ).
Power-Supply Sequencing
and Overvoltage Protection
Do not exceed the absolute maximum ratings, because
stresses beyond the listed ratings may cause permanent damage to the device. Proper power-supply
sequencing is recommended for all CMOS devices.
Always apply V+, followed by V- (when using split supplies) before applying analog signals or logic inputs,
especially if the analog or logic signals are not currentlimited. If this sequencing is not possible and if the analog or logic inputs are not current-limited to less than
Figure 1. Overvoltage Protection Using Blocking Diodes
30mA, add a single diode (D1) for single-supply operation (Figure 1). If using dual supplies or if the analog
signal can dip below ground in single-supply operation,
add two small signal diodes (D1, D2), as shown in
Figure 1. Adding protection diodes reduces the analog
signal range to a diode drop above V- for D2. Leakage
is not affected by adding the diodes. On-resistance
increases by a small amount at low supply voltages.
Maximum supply voltage (V- to V+) must not exceed
17V.
Adding diodes D1 and D2 also protects against some
overvoltage situations. With the circuit of Figure 1, if the
supply voltage is below the absolute maximum rating
and if a fault voltage up to the absolute maximum rating
is applied to an analog signal pin, no damage will
result. For example, with ±5V supplies, analog signals
up to ±8.5V will not damage the circuit of Figure 1. If
only a single fault signal is present, the fault voltage
can go to +12V or -12V without damage.
_______________________________________________________________________________________
9
MAX394
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
______________________________________________Test Circuits/Timing Diagrams
t R < 20ns
t F < 20ns
3V
50%
V IN
50%
0V
+10V
50%
50%
0V
50%
-10V
NO_
300Ω
IN_
t OPEN
MAX394
GND
V+
LOGIC
INPUT
50%
+15V
t OFF
t ON
SWITCH OUTPUT
COM_
-10V
t OFF
V COM
NC_
+10V
t ON
t OPEN
V-
-15V
(REPEAT TEST FOR IN2, IN3, AND IN4.)
Figure 2. Switching-Time Test Circuit
+5V
C
+5V
C
V+
V+
COM
CAPACITANCE
METER
COM
MAX394
IN
CAPACITANCE
METER
0V or 2.4V
NC
or NO
GND
IN
0V or 2.4V
NC or
NO
C
V-
MAX394
GND
C
V-
-5V
-5V
Figure 4. Channel On Capacitance
Figure 3. Channel Off Capacitance
+5V
LOGIC
INPUT
+3V
V+
50%
V COM COM_
VCOM
NC
VO1
0.9VO
IN_
0V
SWITCH
OUTPUT VCOM
VO2
SWITCH
OUTPUT
0V
VO1
NO
0V
0.9VO
LOGIC
INPUT
VO2
MAX394
GND
RL2
CL2
V-
-5V
tD
tD
R L = 1kΩ
C L = 35pF
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
LOGIC 0 INPUT.
Figure 5. Break-Before-Make Delay
10
RL1
______________________________________________________________________________________
CL1
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
+5V
V+
R GEN
∆VO
MAX394
COM_
V GEN
NC OR NO
IN_
GND
VO
VO
CL
10nF
V-
IN_
ON
ON
OFF
-5V
Q = (∆V O )(C L )
Figure 6. Charge Injection
+5V
C
SIGNAL
GENERATOR
COM_
V+
MAX394
0V,
2.4V
IN_
ANALYZER
CH A
CH B
NC_
OR NO_
GND
RL
50Ω
V-
FREQUENCY
TESTED
SIGNAL
GENERATOR
1 MHz
AUTOMATIC
SYNTHESIZER
ANALYZER
TRACKING
SPECTRUM
ANALYZER
C
VCOM
VNC OR VNO
VISO = 20LOG
-5V
C = 5pF
Figure 7. Off Isolation
+5V
C
MAX394
SIGNAL
GENERATOR
50Ω
COM V+
NC OR NO
0V or 2.4V
ANALYZER
CH A
CH B
IN
IN2
NC or NO
GND
0V or 2.4V
COM
V-
FREQUENCY
TESTED
SIGNAL
GENERATOR
ANALYZER
1MHz
AUTOMATIC
SYNTHESIZER
TRACKING
SPECTRUM
ANALYZER
C
RL
-5V
VCT = 20LOG
VCOM
VNC OR VNO
Figure 8. Crosstalk Test Circuit
______________________________________________________________________________________
11
MAX394
_________________________________Test Circuits/Timing Diagrams (continued)
MAX394
Low-Voltage, Quad, SPDT,
CMOS Analog Switch
___________________Chip Topography
NO1
IN1
IN4
NO4
COM1
COM4
NC1
NC4
0.128"
V+ (3.25mm)
VGND
NC2
NC3
COM2
COM3
NO2
IN3
0.100"
(2.54mm)
NO3
IN2
SUBSTRATE IS CONNECTED TO V+
TRANSISTOR COUNT: 137
________________________________________________________Package Information
D
E
DIM
E1
A
A1
A2
A3
B
B1
C
D1
E
E1
e
eA
eB
L
A3
A A2
L A1
0° - 15°
C
e
B1
B
eA
eB
D1
Plastic DIP
PLASTIC
DUAL-IN-LINE
PACKAGE
(0.300 in.)
INCHES
MAX
MIN
0.200
–
–
0.015
0.175
0.125
0.080
0.055
0.022
0.016
0.065
0.045
0.012
0.008
0.080
0.005
0.325
0.300
0.310
0.240
–
0.100
–
0.300
0.400
–
0.150
0.115
PKG. DIM PINS
P
P
P
P
P
N
D
D
D
D
D
D
8
14
16
18
20
24
INCHES
MIN
MAX
0.348 0.390
0.735 0.765
0.745 0.765
0.885 0.915
1.015 1.045
1.14 1.265
MILLIMETERS
MIN
MAX
–
5.08
0.38
–
3.18
4.45
1.40
2.03
0.41
0.56
1.14
1.65
0.20
0.30
0.13
2.03
7.62
8.26
6.10
7.87
2.54
–
7.62
–
–
10.16
2.92
3.81
MILLIMETERS
MIN
MAX
8.84
9.91
18.67 19.43
18.92 19.43
22.48 23.24
25.78 26.54
28.96 32.13
21-0043A
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1995 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.