SMSC LAN9118

LAN9118
High Performance
Single-Chip 10/100 NonPCI Ethernet Controller
PRODUCT FEATURES
Datasheet
Highlights
„
„
„
„
„
„
„
Optimized for the highest data-rate applications such
as high-definition video and multi-media applications
Efficient architecture with low CPU overhead
Easily interfaces to most 32-bit and 16-bit embedded
CPU’s
Integrated PHY
Supports audio & video streaming over Ethernet:
multiple high-definition (HD) MPEG2 streams
Pin compatible with other members of LAN9118
family (LAN9117, LAN9116 and LAN9115)
—
—
—
—
—
„
„
„
„
„
„
Video distribution systems, multi-room PVR
High-end Cable, satellite, and IP set-top boxes
Digital video recorders
High definition televisions
Digital media clients/servers
Home gateways
Key Benefits
„
„
„
Eliminates dropped packets
„
High-Performance host bus interface
Miscellaneous features
— Low profile 100-pin, TQFP lead-free RoHS Compliant
package
— Integral 1.8V regulator
— General Purpose Timer
— Support for optional EEPROM
— Support for 3 status LEDs multiplexed with
Programmable GPIO signals
Minimizes CPU overhead
Reduces system cost and increases design flexibility
— SRAM-like interface easily interfaces to most
embedded CPU’s or SoC’s
— Low-cost, low--pin count non-PCI interface for
embedded designs
Integrated Ethernet PHY
— Simple, SRAM-like interface
— 32/16-bit data bus
— Large, 16Kbyte FIFO memory that can be allocated to
RX or TX functions
— One configurable host interrupt
— Supports Slave-DMA
— Interrupt Pin with Programmable Hold-off timer
„
One 48-bit perfect address
64 hash-filtered multicast addresses
Pass all multicast
Promiscuous mode
Inverse filtering
Pass all incoming with status report
Disable reception of broadcast packets
— Auto-negotiation
— Automatic polarity detection and correction
Supports highest performance applications
— Internal buffer memory can store over 200 packets
— Supports automatic or host-triggered PAUSE and backpressure flow control
Fully compliant with IEEE 802.3/802.3u standards
Integrated Ethernet MAC and PHY
10BASE-T and 100BASE-TX support
Full- and Half-duplex support
Full-duplex flow control
Backpressure for half-duplex flow control
Preamble generation and removal
Automatic 32-bit CRC generation and checking
Automatic payload padding and pad removal
Loop-back modes
Flexible address filtering modes
—
—
—
—
—
—
—
„
— Highest performing non-PCI Ethernet controller in the
market
— 32-bit interface with fast bus cycle times
— Burst-mode read support
„
„
Numerous power management modes
Wake on LAN*
Magic packet wakeup*
Wakeup indicator event signal
Link Status Change
Single chip Ethernet controller
—
—
—
—
—
—
—
—
—
—
Target Applications
„
Reduced Power Modes
„
„
3.3V Power Supply with 5V tolerant I/O
0 to 70°C
* Third-party brands and names are the property of their respective
owners.
SMSC LAN9118
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
ORDER NUMBER:
LAN9118-MT FOR 100 PIN, TQFP LEAD-FREE ROHS COMPLIANT PACKAGE WITH E3 FINISH
(MATTE TIN)
80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123
Copyright © 2007 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete
information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no
responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without
notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does
not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC
or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard
Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors
known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request.
SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause
or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further
testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale
Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems
Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND
ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY
DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR
REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC
OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO
HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Revision 1.3 (05-31-07)
2
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table of Contents
Chapter 1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Internal Block Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10/100 Ethernet PHY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10/100 Ethernet MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receive and Transmit FIFOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPIO Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Purpose Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Host Bus Interface (SRAM Interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
11
12
12
12
12
12
12
12
Chapter 2 Pin Description and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.1
Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Chapter 3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
10/100 Ethernet MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1
Full-Duplex Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2
Half-Duplex Flow Control (Backpressure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3
Virtual Local Area Network (VLAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address Filtering Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filtering Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.1
Perfect Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.2
Hash Only Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wake-up Frame Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.1
Magic Packet Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32-bit vs. 16-bit Host Bus Width Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.1
16-bit Bus Writes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.2
16-bit Bus Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Big and Little Endian Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Purpose Timer (GP Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.1
MAC Address Auto-Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.2
EEPROM Host Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.10.1 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.10.2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.10.3 Internal PHY Power-Down modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detailed Reset Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11.1 Power-On Reset (POR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11.2 Hardware Reset Input (nRESET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11.3 Resume Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11.4 Soft Reset (SRST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11.5 PHY Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TX Data Path Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.1 TX Buffer Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.2 TX Command Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.3 TX Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.4 TX Status Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.5 Calculating Actual TX Data FIFO Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMSC LAN9118
3
DATASHEET
22
23
23
23
23
26
26
26
26
27
29
30
30
30
30
31
31
32
32
38
38
38
40
41
42
42
42
42
42
43
45
45
47
48
49
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.13
3.12.6 Transmit Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.7 TX Data FIFO Underrun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.8 Transmitter Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.9 Stopping and Starting the Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RX Data Path Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.13.1 RX Slave PIO Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.13.2 RX Packet Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.13.3 RX Status Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.13.4 Stopping and Starting the Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.13.5 Receiver Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
52
52
52
52
53
55
56
56
57
Chapter 4 Internal Ethernet PHY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Top Level Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100Base-TX Transmit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.1
4B/5B Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2
Scrambling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3
NRZI and MLT3 Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.4
100M Transmit Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5
100M Phase Lock Loop (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100Base-TX Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1
100M Receive Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2
Equalizer, Baseline Wander Correction and Clock and Data Recovery . . . . . . . . . . . . .
4.3.3
NRZI and MLT-3 Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.4
Descrambling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.5
Alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.6
5B/4B Decoding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10Base-T Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.1
10M Transmit Data across the internal MII bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.2
Manchester Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.3
10M Transmit Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10Base-T Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.1
10M Receive Input and Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.2
Manchester Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.3
Jabber Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7.1
Re-starting Auto-negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7.2
Disabling Auto-negotiation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7.3
Half vs. Full-Duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
58
58
58
60
60
60
60
61
61
61
61
62
62
62
62
62
62
63
63
63
63
63
63
65
65
65
65
Chapter 5 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5.1
5.2
5.3
Register Nomenclature and Access Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RX and TX FIFO Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.1
RX FIFO Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.2
TX FIFO Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Control and Status Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.1
ID_REV—Chip ID and Revision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.2
IRQ_CFG—Interrupt Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.3
INT_STS—Interrupt Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.4
INT_EN—Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.5
BYTE_TEST—Byte Order Test Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.6
FIFO_INT—FIFO Level Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.7
RX_CFG—Receive Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.8
TX_CFG—Transmit Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.9
HW_CFG—Hardware Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision 1.3 (05-31-07)
4
DATASHEET
68
68
68
69
69
70
71
72
73
74
75
75
76
77
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.4
5.5
5.3.10 RX_DP_CTRL—Receive Datapath Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5.3.11 RX_FIFO_INF—Receive FIFO Information Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5.3.12 TX_FIFO_INF—Transmit FIFO Information Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
5.3.13 PMT_CTRL— Power Management Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
5.3.14 GPIO_CFG—General Purpose IO Configuration Register . . . . . . . . . . . . . . . . . . . . . . . 84
5.3.15 GPT_CFG-General Purpose Timer Configuration Register . . . . . . . . . . . . . . . . . . . . . . 85
5.3.16 GPT_CNT-General Purpose Timer Current Count Register . . . . . . . . . . . . . . . . . . . . . . 86
5.3.17 WORD_SWAP—Word Swap Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
5.3.18 FREE_RUN—Free-Run 25MHz Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
5.3.19 RX_DROP– Receiver Dropped Frames Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
5.3.20 MAC_CSR_CMD – MAC CSR Synchronizer Command Register . . . . . . . . . . . . . . . . . 88
5.3.21 MAC_CSR_DATA – MAC CSR Synchronizer Data Register . . . . . . . . . . . . . . . . . . . . . 88
5.3.22 AFC_CFG – Automatic Flow Control Configuration Register . . . . . . . . . . . . . . . . . . . . . 89
5.3.23 E2P_CMD – EEPROM Command Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
5.3.24 E2P_DATA – EEPROM Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
MAC Control and Status Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
5.4.1
MAC_CR—MAC Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
5.4.2
ADDRH—MAC Address High Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
5.4.3
ADDRL—MAC Address Low Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
5.4.4
HASHH—Multicast Hash Table High Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
5.4.5
HASHL—Multicast Hash Table Low Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
5.4.6
MII_ACC—MII Access Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
5.4.7
MII_DATA—MII Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
5.4.8
FLOW—Flow Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
5.4.9
VLAN1—VLAN1 Tag Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
5.4.10 VLAN2—VLAN2 Tag Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5.4.11 WUFF—Wake-up Frame Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5.4.12 WUCSR—Wake-up Control and Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
PHY Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
5.5.1
Basic Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
5.5.2
Basic Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
5.5.3
PHY Identifier 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.5.4
PHY Identifier 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.5.5
Auto-negotiation Advertisement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.5.6
Auto-negotiation Link Partner Ability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.5.7
Auto-negotiation Expansion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5.5.8
Mode Control/Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5.5.9
Special Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
5.5.10 Special Control/Status Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
5.5.11 Interrupt Source Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
5.5.12 Interrupt Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
5.5.13 PHY Special Control/Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Chapter 6 Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
Host Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.1
Special Restrictions on Back-to-Back Write/Read Cycles . . . . . . . . . . . . . . . . . . . . . . .
6.1.2
Special Restrictions on Back-to-Back Read Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIO Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIO Burst Reads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RX Data FIFO Direct PIO Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RX Data FIFO Direct PIO Burst Reads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIO Writes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TX Data FIFO Direct PIO Writes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EEPROM Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMSC LAN9118
5
DATASHEET
112
112
113
114
115
116
117
118
119
121
121
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Chapter 7 Operational Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
7.1
7.2
7.3
7.4
7.5
7.6
Absolute Maximum Ratings*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Conditions** . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Consumption Device Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Consumption Device and System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
123
123
124
124
125
127
Chapter 8 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Revision 1.3 (05-31-07)
6
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
List of Figures
Figure 1.1
Figure 1.2
Figure 2.1
Figure 3.1
Figure 3.2
Figure 3.3
Figure 3.4
Figure 3.5
Figure 3.6
Figure 3.7
Figure 3.8
Figure 3.9
Figure 3.10
Figure 3.11
Figure 3.12
Figure 3.13
Figure 3.14
Figure 3.15
Figure 3.16
Figure 3.17
Figure 3.18
Figure 4.1
Figure 4.2
Figure 5.1
Figure 5.2
Figure 6.1
Figure 6.2
Figure 6.3
Figure 6.4
Figure 6.5
Figure 6.6
Figure 6.7
Figure 8.1
System Block Diagram Utilizing the SMSC LAN9118 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Internal Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
VLAN Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
VLAN Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
EEPROM Access Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
EEPROM ERASE Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
EEPROM ERAL Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
EEPROM EWDS Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
EEPROM EWEN Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
EEPROM READ Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
EEPROM WRITE Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
EEPROM WRAL Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
PME and PME_INT Signal Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Simplified Host TX Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
TX Buffer Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
TX Example 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
TX Example 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Host Receive Routine Using Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Host Receive Routine with Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
RX Packet Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
100Base-TX Data Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Receive Data Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
LAN9118 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Example ADDRL, ADDRH and EEPROM Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
LAN9118 PIO Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
LAN9118 PIO Burst Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
RX Data FIFO Direct PIO Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
RX Data FIFO Direct PIO Burst Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
PIO Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
TX Data FIFO Direct PIO Write Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
EEPROM Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
100 Pin TQFP Package Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
SMSC LAN9118
7
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
List of Tables
Table 2.1 Host Bus Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 2.2 Default Ethernet Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 2.3 LAN Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 2.4 Serial EEPROM Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 2.5 System and Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 2.6 Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 3.1 Address Filtering Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 3.2 Wake-Up Frame Filter Register Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 3.3 Filter i Byte Mask Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 3.4 Filter i Command Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 3.5 Filter i Offset Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 3.6 Filter i CRC-16 Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 3.7 Byte Lane Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 3.8 Required EECLK Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 3.9 Power Management States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Table 3.10 Reset Sources and Affected Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 3.11 TX Command 'A' Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 3.12 TX Command 'B' Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 3.13 TX DATA Start Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 4.1 4B/5B Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 4.2 CRS Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Table 5.1 LAN9118 Direct Address Register Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 5.2 RX Alignment Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Table 5.3 Valid TX/RX FIFO Allocations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Table 5.4 EEPROM Enable Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table 5.5 Backpressure Duration Bit Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Table 5.6 LAN9118 MAC CSR Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Table 5.7 ADDRL, ADDRH and EEPROM Byte Ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Table 5.8 LAN9118 PHY Control and Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Table 5.9 MODE Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Table 6.1 Read After Write Timing Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Table 6.2 Read After Read Timing Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Table 6.3 PIO Read Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Table 6.4 PIO Burst Read Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Table 6.5 RX Data FIFO Direct PIO Read Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Table 6.6 RX Data FIFO Direct PIO Burst Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Table 6.7 PIO Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Table 6.8 TX Data FIFO Direct PIO Write Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Table 6.9 Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Table 6.10 EEPROM Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Table 7.1 Power Consumption Device Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Table 7.2 Power Consumption Device and System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Table 7.3 I/O Buffer Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Table 7.4 100BASE-TX Tranceiver Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Table 7.5 10BASE-T Tranceiver Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Table 7.6 LAN9118 Crystal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Table 8.1 100 Pin TQFP Package Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Revision 1.3 (05-31-07)
8
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Chapter 1 General Description
The LAN9118 is a full-featured, single-chip 10/100 Ethernet controller designed for embedded
applications where performance, flexibility, ease of integration and system cost control are required.
The LAN9118 has been specifically architected to provide the highest performance possible for any
given architecture. The LAN9118 is fully IEEE 802.3 10BASE-T and 802.3u 100BASE-TX compliant.
The LAN9118 includes an integrated Ethernet MAC and PHY with a high-performance SRAM-like slave
interface. The simple, yet highly functional host bus interface provides a glue-less connection to most
common 16-bit and 32-bit microprocessors and microcontrollers. The LAN9118 includes large transmit
and receive data FIFOs with a high-speed host bus interface to accommodate high bandwidth, high
latency applications. In addition, the LAN9118 memory buffer architecture allows the most efficient use
of memory resources by optimizing packet granularity.
Applications
The LAN9118 is well suited for many high-performance embedded applications, including:
„
High-end cable, satellite and IP set-top boxes
„
Video distribution systems
„
Multi-room PVR (Personal Video Recorder)
„
Digital video recorders
„
High-definition televisions
„
Digital media clients/servers
„
Home gateways
The LAN9118 also supports features which reduce or eliminate packet loss. Its internal 16-KByte
SRAM can hold over 200 received packets. If the receive FIFO gets too full, the LAN9118 can
automatically generate flow control packets to the remote node, or assert back-pressure on the remote
node by generating network collisions.
The LAN9118 supports numerous power management and wakeup features. The LAN9118 can be
placed in a reduced power mode and can be programmed to issue an external wake signal via several
methods, including “Magic Packet”, “Wake on LAN” and “Link Status Change”. This signal is ideal for
triggering system power-up using remote Ethernet wakeup events. The device can be removed from
the low power state via a host processor command.
SMSC LAN9118
9
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
System Memory
System Memory
System
Peripherals
Magnetics
Microprocessor/
Microcontroller
System Bus
Ethernet
LAN9118
LEDS/GPIO
25MHz
XTAL
EEPROM
(Optional)
Figure 1.1 System Block Diagram Utilizing the SMSC LAN9118
The SMSC LAN9118 integrated 10/100 MAC/PHY controller is a peripheral chip that performs the
function of translating parallel data from a host controller into Ethernet packets. The LAN9118 Ethernet
MAC/PHY controller is designed and optimized to function in an embedded environment. All
communication is performed with programmed I/O transactions using the simple SRAM-like host
interface bus.
The diagram shown above, describes a typical system configuration of the LAN9118 in a typical
embedded environment.
The LAN9118 is a general purpose, platform independent, Ethernet controller. The LAN9118 consists
of four major functional blocks. The four blocks are:
„
10/100 Ethernet PHY
„
10/100 Ethernet MAC
„
RX/TX FIFOs
„
Host Bus Interface (HBI)
Revision 1.3 (05-31-07)
10
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
1.1
Internal Block Overview
This section provides an overview of each of these functional blocks as shown in Figure 1.2, "Internal
Block Diagram".
25MHz
EEPROM
(Optional)
+3.3V
3.3V to 1.8V
Regulator
PME
Wakup Indicator
PLL
EEPROM
Controller
Power Management
Host Bus Interface
(HBI)
SRAM I/F
2kB to 14kB
Configurable TX FIFO
10/100
Ethernet
MAC
TX Status FIFO
PIO Controller
RX Status FIFO
IRQ
FIFO_SEL
Interrupt
Controller
2kB to 14kB
Configurable RX FIFO
GP Timer
10/100
Ethernet
PHY
LAN
MIL - RX Elastic
Buffer - 128 bytes
MIL - TX Elastic
Buffer - 2K bytes
Figure 1.2 Internal Block Diagram
1.2
10/100 Ethernet PHY
The LAN9118 integrates an IEEE 802.3 physical layer for twisted pair Ethernet applications. The PHY
can be configured for either 100 Mbps (100Base-TX) or 10 Mbps (10Base-T) Ethernet operation in
either full or half duplex configurations. The PHY block includes auto-negotiation.
Minimal external components are required for the utilization of the Integrated PHY.
1.3
10/100 Ethernet MAC
The transmit and receive data paths are separate within the MAC allowing the highest performance
especially in full duplex mode. The data paths connect to the PIO interface Function via separate
busses to increase performance. Payload data as well as transmit and receive status is passed on
these busses.
A third internal bus is used to access the MAC’s Control and Status Registers (CSR’s). This bus is
accessible from the host through the PIO interface function.
On the backend, the MAC interfaces with the internal 10/100 PHY through a the MII (Media
Independent Interface) port internal to the LAN9118. The MAC CSR's also provides a mechanism for
accessing the PHY’s internal registers through the internal SMI (Serial Management Interface) bus.
The MAC Interface Layer (MIL), within the MAC, contains a 2K Byte transmit and a 128 Byte receive
FIFO which is separate from the TX and RX FIFOs. The FIFOs within the MAC are not directly
accessible from the host interface. The differentiation between the TX/RX FIFO memory buffers and
the MAC buffers is that when the transmit or receive packets are in the MAC buffers, the host no longer
can control or access the TX or RX data. The MAC buffers (both TX and RX) are in effect the working
SMSC LAN9118
11
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
buffers of the Ethernet MAC logic. In the case of reception, the data must be moved first to the RX
FIFOs for the host to access the data.
1.4
Receive and Transmit FIFOs
The Receive and Transmit FIFOs allow increased packet buffer storage to the MAC. The FIFOs are a
conduit between the host interface and the MAC through which all transmitted and received data and
status information is passed. Deep FIFOs allow a high degree of latency tolerance relative to the
various transport and OS software stacks thus reducing or minimizing overrun conditions. Like the
MAC, the FIFOs have separate receive and transmit data paths. In addition, the RX and TX FIFOs are
configurable in size, allowing increased flexibility.
1.5
Interrupt Controller
The LAN9118 supports a single programmable interrupt. The programmable nature of this interrupt
allows the user the ability to optimize performance dependent upon the application requirement. Both
the polarity and buffer type of the interrupt pin are configurable for the external interrupt processing.
The interrupt line can be configured as an open-drain output to facilitate the sharing of interrupts with
other devices. In addition, a programmable interrupt de-assertion interval is provided.
1.6
GPIO Interface
A 3-bit GPIO and 2-bit GPO (Multiplexed on the EEPROM and LED Pins) interface is included in the
LAN9118. It is accessible through the host bus interface via the CSRs. The GPIO signals can function
as inputs, push-pull outputs and open drain outputs. The GPIO’s (GPO’s are not configurable) can also
be configured to trigger interrupts with programmable polarity.
1.7
Serial EEPROM Interface
A serial EEPROM interface is included in the LAN9118. The serial EEPROM is optional and can be
programmed with the LAN9118 MAC address. The LAN9118 can optionally load the MAC address
automatically after power-on.
1.8
Power Management Controls
The LAN9118 supports comprehensive array of power management modes to allow use in power
sensitive applications. Wake on LAN, Link Status Change and Magic Packet detection are supported
by the LAN9118. An external PME (Power Management Event) interrupt is provided to indicate
detection of a wakeup event.
1.9
General Purpose Timer
The general-purpose timer has no dedicated function within the LAN9118 and may be programmed to
issue a timed interrupt.
1.10
Host Bus Interface (SRAM Interface)
The host bus interface provides a FIFO interface for the transmit and receive data paths, as well as
an interface for the LAN9118 Control and Status Registers (CSR’s).
The host bus interface is the primary bus for connection to the embedded host system. This interface
models an asynchronous SRAM. TX FIFO, RX FIFO, and CSR’s are accessed through this interface.
Programmed I/O transactions are supported.
Revision 1.3 (05-31-07)
12
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
The LAN9118 host bus interface supports 32-bit and 16-bit bus transfers; internally, all data paths are
32-bits wide. The LAN9118 can be interfaced to either Big-Endian or Little-Endian processors in either
32-bit or 16-bit external bus width modes of operation.
The host bus data Interface is responsible for host address decoding and data bus steering. The host
bus interface handles the 16 to 32-bit conversion when the LAN9118 is configured with a 16-bit host
interface. Additionally, when Big Endian mode is selected, the data path to the internal controller
registers will be reorganized accordingly.
SMSC LAN9118
13
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
NC
SPEED_SEL
NC
IRQ
NC
PME
EECLK**
EECS
EEDIO**
GND_CORE
VDD_CORE
D0
D1
D2
VDD_IO
GND_IO
D3
D4
D5
D6
VDD_IO
GND_IO
D7
D8
D9
Chapter 2 Pin Description and Configuration
FIFO_SEL
VSS_A
TPO-
76
TPO+
VSS_A
VDD_A
79
80
81
82
TPITPI+
NC
VDD_A
VSS_A
EXRES1
VSS_A
VDD_A
NC*2
NC*1
nRD
nWR
nCS
nRESET
GND_IO
VDD_IO
GPIO0/nLED1**
83
84
85
86
87
88
89
90
91
92
93
SMSC
LAN9118
100 PIN TQFP
94
95
96
97
98
99
100
50
49
48
D10
D11
VDD_IO
47
46
45
GND_IO
D12
D13
44
43
D14
D15
42
41
40
VDD_IO
GND_IO
D16
39
38
37
D17
D18
D19
36
35
34
D20
VDD_IO
GND_IO
33
D21
32
D22
31
30
D23
D24
29
28
27
26
D25
VDD_IO
GND_IO
D26
GND_CORE
VREG
VDD_CORE
VSS_PLL
XTAL2
XTAL1
VDD_PLL
VDD_REF
ATEST
RBIAS
VSS_REF
A7
A6
A5
A4
A3
A2
A1
GND_IO
VDD_IO
D31
D30
D29
D28
D27
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
GPIO1/nLED2**
GPIO2/nLED3**
77
78
**Denotes a multifunction pin
*1 This NC pin can also be tied to VDD_A for backward compatibility
*2 This NC pin can also be tied to VSS_A for backward compatibility
Figure 2.1 Pin Configuration
Revision 1.3 (05-31-07)
14
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 2.1 Host Bus Interface Signals
PIN NO.
NAME
SYMBOL
BUFFER
TYPE
#
PINS
21-26,2933,36-40
Host Data High
D[31:16]
I/O8 (PD)
16
Bi-directional data port.
Note that Pull-down’s are disabled in
32 bit mode.
43-46,4953,56-59,6264
Host Data Low
D[15:0]
I/O8
16
Bi-directional data port.
12-18
Host Address
A[7:1]
IS
7
7-bit Address Port. Used to select
Internal CSR’s and TX and RX FIFOs.
92
Read Strobe
nRD
IS
1
Active low strobe to indicate a read
cycle.
93
Write Strobe
nWR
IS
1
Active low strobe to indicate a write
cycle. This signal, qualified with nCS, is
also used to wakeup the LAN9118
when it is in a reduced power state.
94
Chip Select
nCS
IS
1
Active low signal used to qualify read
and write operations. This signal
qualified with nWR is also used to
wakeup the LAN9118 when it is in a
reduced power state.
72
Interrupt
Request
IRQ
O8/OD8
1
Programmable Interrupt request.
Programmable polarity, source and
buffer types.
76
FIFO Select
FIFO_SEL
IS
1
When driven high all accesses to the
LAN9118 are to the RX or TX Data
FIFOs. In this mode, the A[7:3] upper
address inputs are ignored.
DESCRIPTION
Table 2.2 Default Ethernet Settings
DEFAULT ETHERNET SETTINGS
SPEED_SEL
SPEED
DUPLEX
AUTO NEG.
0
10MBPS
HALF-DUPLEX
DISABLED
1
100MBPS
HALF-DUPLEX
ENABLED
SMSC LAN9118
15
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 2.3 LAN Interface Signals
PIN
NO.
NAME
SYMBOL
BUFFER
TYPE
NUM
PINS
79
TXP
TPO+
AO
1
Twisted Pair Transmit Output,
Positive
78
TXN
TPO-
AO
1
Twisted Pair Transmit Output,
Negative
83
RXP
TPI+
AI
1
Twisted Pair Receive Input, Positive
82
RXN
TPI-
AI
1
Twisted Pair Receive Input, Negative
87
PHY External Bias
Resistor
EXRES1
AI
1
Must be connected to ground through
a 12.4K ohm 1% resistor.
DESCRIPTION
Table 2.4 Serial EEPROM Interface Signals
PIN
NO.
67
NAME
SYMBOL
EEPROM Data,
GPO3, TX_EN,
TX_CLK,
D32/nD16
EEDIO/GPO3/
TX_EN/TX_CLK
BUFFER
TYPE
NUM
PINS
I/O8
1
(D32/nD16)
DESCRIPTION
EEPROM Data: This bi-directional
pin can be connected to a serial
EEPROM DIO. This is optional.
General Purpose Output 3: This
pin can also function as a general
purpose output, or it can be
configured to monitor the TX_EN or
TX_CLK signals on the internal MII
port. When configured as a GPO
signal, or as a TX_EN/TX_CLK
monitor, the EECS pin is deasserted
so as to never unintentionally access
the serial EEPROM. This signal
cannot function as a generalpurpose input.
Data Bus Width Select: This signal
also functions as a configuration
input on power-up and is used to
select the host bus data width. Upon
deassertion of reset, the value of the
input is latched. When high, a 32-bit
data bus is utilized. When low, a 16bit interface is utilized.
68
EEPROM Chip
Select
Revision 1.3 (05-31-07)
EECS
O8
16
DATASHEET
1
Serial EEPROM chip select.
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 2.4 Serial EEPROM Interface Signals (continued)
PIN
NO.
69
NAME
SYMBOL
EEPROM Clock,
GPO4 RX_DV,
RX_CLK
EECLK/GPO4/
RX_DV/RX_CLK
BUFFER
TYPE
NUM
PINS
O8
1
DESCRIPTION
EEPROM Clock: Serial EEPROM
Clock pin.
General Purpose Output 4: This
pin can also function as a generalpurpose output, or it can be
configured to monitor the RX_DV or
RX_CLK signals on the internal MII
port. When configured as a GPO
signal, or as an RX_DV/RX_CLK
monitor, the EECS pin is deasserted
so as to never unintentionally access
the serial EEPROM. This signal
cannot function as a generalpurpose input.
Table 2.5 System and Power Signals
PIN
NO.
NAME
SYMBOL
BUFFER
TYPE
NUM
PINS
DESCRIPTION
6
Crystal 1
XTAL1
lclk
1
External 25MHz Crystal Input.
Can also be connected to singleended TTL oscillator. If this method is
implemented, XTAL2 should be left
unconnected.
5
Crystal 2
XTAL2
Oclk
1
External 25MHz Crystal output.
95
Reset
nRESET
IS
(PU)
1
Active-low reset input. Resets all logic
and registers within the LAN9118
This signal is pulled high with a weak
internal pull-up resistor. If nRESET is
left unconnected, the LAN9118 will
rely on its internal power-on reset
circuitry
Note:
SMSC LAN9118
17
DATASHEET
The LAN9118 must always
be read at least once after
power-up, reset, or upon
return from a power-saving
state or write operations will
not function. See Section
3.11, "Detailed Reset
Description," on page 41 for
additional information
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 2.5 System and Power Signals (continued)
PIN
NO.
70
NAME
Wakeup Indicator
SYMBOL
PME
BUFFER
TYPE
NUM
PINS
O8/OD8
1
DESCRIPTION
When programmed to do so, is
asserted when the LAN9118 detects
a wake event and is requesting the
system to wake up from the
associated sleep state. The polarity
and buffer type of this signal is
programmable.
Note:
71,73,
75,84,
90,91
Reserved
Reserved
74
10/100 Selector
SPEED_SEL
Revision 1.3 (05-31-07)
I (PU)
18
DATASHEET
Detection of a Power
Management Event, and
assertion of the PME signal
will not wakeup the
LAN9118. The LAN9118 will
only wake up when it
detects a host write cycle
(assertion of nCS and
nWR). Although any write to
the LAN9118, regardless of
the data written, will wakeup the device when it is in a
power-saving mode, it is
required that the
BYTE_TEST register be
used for this purpose.
5
No Connect
1
This signal functions as a
configuration input on power-up and
is used to select the default Ethernet
settings. Upon deassertion of reset,
the value of the input is latched. This
signal functions as shown in
Table 2.2, "Default Ethernet Settings",
below.
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 2.5 System and Power Signals (continued)
PIN
NO.
100,
99, 98
NAME
General Purpose
I/O data,
nLED1 (Speed
Indicator),
nLED2 (Link &
Activity Indicator),
SYMBOL
GPIO[2:0]/
LED[3:1]
BUFFER
TYPE
NUM
PINS
IS/O12/
OD12
3
nLED3 (FullDuplex
Indicator).
DESCRIPTION
General Purpose I/O data: These
three general-purpose signals are
fully programmable as either pushpull output, open-drain output or input
by writing the GPIO_CFG
configuration register in the CSR’s.
They are also multiplexed as GP LED
connections.
GPIO signals are Schmitt-triggered
inputs. When configured as LED
outputs these signals are open-drain.
nLED1 (Speed Indicator). This
signal is driven low when the
operating speed is 100Mbs, during
auto-negotiation and when the cable
is disconnected. This signal is driven
high only during 10Mbs operation.
nLED2 (Link & Activity Indicator).
This signal is driven low (LED on)
when the LAN9118 detects a valid
link. This signal is pulsed high (LED
off) for 80mS whenever transmit or
receive activity is detected. This
signal is then driven low again for a
minimum of 80mS, after which time it
will repeat the process if TX or RX
activity is detected. Effectively, LED2
is activated solid for a link. When
transmit or receive activity is sensed
LED2 will flash as an activity
indicator.
nLED3 (Full-Duplex Indicator). This
signal is driven low when the link is
operating in full-duplex mode.
10
RBIAS
RBIAS
AI
1
PLL Bias: Connect to an external
12.0K ohm 1.0% resistor to ground.
Used for the PLL Bias circuit.
9
Test Pin
ATEST
I
1
This pin must be connected to VDD
for normal operation.
2
Internal Regulator
Power
VREG
P
1
3.3V input for internal voltage
regulator
20,28,
35,
42,48,
55,61,
97
+3.3V I/O Power
VDD_IO
P
8
+3.3V I/O logic power supply pins
19,27,
34,41,
47,54,
60,96
I/O Ground
GND_IO
P
8
Ground for I/O pins
81,85,
89
+3.3V Analog
Power
VDD_A
P
3
+3.3V Analog power supply pins. See
Note 2.1
77,80,
86,88
Analog Ground
VSS_A
P
4
Ground for analog circuitry
SMSC LAN9118
19
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 2.5 System and Power Signals (continued)
PIN
NO.
NAME
BUFFER
TYPE
SYMBOL
NUM
PINS
DESCRIPTION
3,65
Core Voltage
Decoupling
VDD_CORE
P
2
1.8 V from internal core regulator.
Both pins must be connected
together externally and then tied to a
10uF 0.1-Ohm ESR capacitor, in
parallel with a 0.01uF capacitor to
Ground next to each pin. See
Note 2.1
1,66
Core Ground
GND_CORE
P
2
Ground for internal digital logic
7
PLL Power
VDD_PLL
P
1
1.8V Power from the internal PLL
regulator. This external pin must be
connected to a 10uF 0.1-Ohm ESR
capacitor, in parallel with a 0.01uF
capacitor to Ground. See Note 2.1
4
PLL Ground
VSS_PLL
P
1
GND for the PLL
8
Reference Power
VDD_REF
P
1
Connected to 3.3v power and used
as the reference voltage for the
internal PLL
11
Reference Ground
VSS_REF
P
1
Ground for internal PLL reference
voltage
Note 2.1
2.1
Please refer to the SMSC application note AN 12.5 titled “Designing with the LAN9118 Getting Started”. It is also important to note that this application note applies to the whole
SMSC LAN9118 family of Ethernet controllers. However, subtle differences may apply.
Buffer Types
Table 2.6 Buffer Types
TYPE
I
IS
O12
OD12
DESCRIPTION
Input pin
Schmitt triggered Input
Output with 12mA sink and 12mA source
Open-drain output with 12mA sink
IO8
I/O with 8mA symmetrical drive
OD8
Open-drain output with 8mA sink
O8
Output 8mA symmetrical drive
PU
50uA (typical) internal pull-up
PD
50uA (typical) internal pull-down
AI
Analog input
AO
Analog output
Revision 1.3 (05-31-07)
20
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 2.6 Buffer Types (continued)
TYPE
DESCRIPTION
AIO
Analog bi-directional
ICLK
Crystal oscillator input pin
OCLK
Crystal oscillator output pin
SMSC LAN9118
21
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Chapter 3 Functional Description
3.1
10/100 Ethernet MAC
The Ethernet Media Access controller (MAC) incorporates the essential protocol requirements for
operating an Ethernet/IEEE 802.3-compliant node and provides an interface between the host
subsystem and the internal Ethernet PHY. The MAC can operate in either 100-Mbps or 10-Mbps mode.
The MAC operates in both half-duplex and full-duplex modes. When operating in half-duplex mode,
the MAC complies fully with Section 4 of ISO/IEC 8802-3 (ANSI/IEEE standard) and ANSI/IEEE 802.3
standards. When operating in full-duplex mode, the MAC complies with IEEE 802.3x full-duplex
operation standard.
The MAC provides programmable enhanced features designed to minimize host supervision, bus
utilization, and pre- or post-message processing. These features include the ability to disable retries
after a collision, dynamic FCS (Frame Check Sequence) generation on a frame-by-frame basis,
automatic pad field insertion and deletion to enforce minimum frame size attributes, and automatic
retransmission and detection of collision frames.
The MAC can sustain transmission or reception of minimally-sized back-to-back packets at full line
speed with an interpacket gap (IPG) of 9.6 microseconds for 10 Mbps and 0.96 microseconds for 100
Mbps.
The primary attributes of the MAC Function are:
„
Transmit and receive message data encapsulation
„
Framing (frame boundary delimitation, frame synchronization)
„
Error detection (physical medium transmission errors)
„
Media access management
„
Medium allocation (collision detection, except in full-duplex operation)
„
Contention resolution (collision handling, except in full-duplex operation)
„
Flow control during full-duplex mode
„
Decoding of control frames (PAUSE command) and disabling the transmitter
„
Generation of control frames
„
Interface to the internal PHYl
The transmit and receive data paths are separate within the LAN9118 from the MAC to host interface
allowing the highest performance, especially in full duplex mode. Payload data as well as transmit and
receive status are passed on these busses.
A third internal bus is used to access the MAC’s “Control and Status Registers” (CSR’s). This bus is
also accessible from the host.
On the backend, the MAC interfaces with the 10/100 PHY through an internal MII (Media Independent
Interface) port, internal to the LAN9118. The MAC CSR's also provide a mechanism for accessing the
PHY’s internal registers through the internal SMI (Serial Management Interface) bus.
The receive and transmit FIFOs allow increased packet buffer storage to the MAC. The FIFOs are a
conduit between the host interface and the MAC through which all transmitted and received data and
status information is passed. Deep FIFOs allow a high degree of latency tolerance relative to the
various transport and OS software stacks reducing and minimizing overrun conditions. Like the MAC,
the FIFOs have separate receive and transmit data paths.
The LAN9118 can store up to 250 Ethernet packets utuilizing FIFOs, totaling 16K bytes, with a packet
granularity of 4 bytes. This memory is shared by the RX and TX blocks and is configurable in terms
of allocation. This depth of buffer storage minimizes or eliminates receive overruns.
Revision 1.3 (05-31-07)
22
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.2
Flow Control
The LAN9118 Ethernet MAC supports full-duplex flow control using the pause operation and control
frame. It also supports half-duplex flow control using back pressure.
3.2.1
Full-Duplex Flow Control
The pause operation inhibits data transmission of data frames for a specified period of time. A Pause
operation consists of a frame containing the globally assigned multicast address (01-80-C2-00-00-01),
the PAUSE opcode, and a parameter indicating the quantum of slot time (512 bit times) to inhibit data
transmissions. The PAUSE parameter may range from 0 to 65,535 slot times. The Ethernet MAC logic,
on receiving a frame with the reserved multicast address and PAUSE opcode, inhibits data frame
transmissions for the length of time indicated. If a Pause request is received while a transmission is
in progress, then the pause will take effect after the transmission is complete. Control frames are
received and processed by the MAC and are passed on.
The MAC also transmits control frames (pause command) via both hardware and software control. The
software driver requests the MAC to transmit a control frame and gives the value of the PAUSE time
to be used in the control frame. The MAC Function constructs a control frame with the appropriate
values set in all the different fields (as defined in the 802.3x specification) and transmits the frame to
the MII interface. The transmission of the control frame is not affected by the current state of the Pause
timer value that is set because of a recently received control frame.
3.2.2
Half-Duplex Flow Control (Backpressure)
In half-duplex mode, back pressure is used for flow control. Whenever the receive buffer/FIFO
becomes full or crosses a certain threshold level, the MAC starts sending a Jam signal. The MAC
transmit logic enters a state at the end of current transmission (if any), where it waits for the beginning
of a received frame. Once a new frame starts, the MAC starts sending the Jam signal, which will result
in a collision. After sensing the collision, the remote station will back off its transmission. The MAC
continues sending the jam to make other stations defer transmission. The MAC only generates this
collision-based back pressure when it receives a new frame, in order to avoid any late collisions.
3.2.3
Virtual Local Area Network (VLAN)
VLAN is a means to form a “broadcast domain” without restriction on the physical or geographical
location on the members of that domain. VLAN can be implemented in any number of different factors,
such as:
„
Physical port
„
MAC address
„
Layer-3 unicast address
„
Multicast address
„
Date/time in combination with MAC address, etc.
An example of a VLAN is depicted in Figure 3.1, "VLAN Topology". It demonstrates the freedom from
physical constraint on the network, and the ability to divide a single switched network into a smaller
broadcast domain.
Moreover, VLAN offers a number of other advantages, such as:
Configurability: Changes to an existing VLAN can be made on the network administrative level, rather
than on the hardware level. A member of a VLAN can thus change its MAC address or its port and
still be a member of the same VLAN. Extra routing is not necessary.
Security: VLAN can improve security by demanding a predefined authentication before admitting a
new member to the domain.
SMSC LAN9118
23
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Network efficiency: Allows shielding one system resource from traffic not meant for that resource. A
workstation in one VLAN is shielded from traffic on another VLAN, increasing that workstation’s
efficiency.
Broadcast containment: Leakage of broadcast frames from one VLAN to another is prevented.
VLAN 3
VLAN 2
CCC
AAA
DDD
EEE
BBB
VLAN 1
FFF
GGG
HHH
LAN Switch #1
LAN Switch #2
VLAN Config Data
Address
VLAN #
AAA
BBB
CCC
DDD
EEE
FFF
GGG
HHH
VLAN 3
VLAN 3
VLAN 3
VLAN 2
VLAN 2
VLAN 2
VLAN 1
VLAN 1
LAN Switch #3
Figure 3.1 VLAN Topology
When the members of a VLAN are not located on the same physical medium, the VLAN uses a tag
to help it determine how to forward the frame from one member to another. The tag structure was
proprietary until the IEEE released a supplement to 802.3 defining the VLAN frame structure, including
the tag. This new frame structure for VLAN is depicted in Figure 3.2, "VLAN Frame".
Revision 1.3 (05-31-07)
24
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Figure 3.2 VLAN Frame
The MAC Function recognizes transmitted and received frames tagged with either one-level or twolevel VLAN IDs. The MAC compares the thirteenth and fourteenth bytes of transmit and receive frames
to the contents of both the one-level VLAN tag register and the two-level VLAN tag register. If a match
is found, the MAC Function identifies the frame as either a one- or two-level VLAN frame, depending
on where the match was found. Upon recognizing that a frame has a VLAN tag, counter thresholds
are adjusted to account for the extra bytes that the VLAN tag adds to the frame. The maximum length
of the good packet is thus changed from 1518 bytes to 1522 bytes.
SMSC LAN9118
25
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.3
Address Filtering Functional Description
The Ethernet address fields of an Ethernet Packet, consists of two 6-byte fields: one for the destination
address and one for the source address. The first bit of the destination address signifies whether it is
a physical address or a multicast address.
The LAN9118 address check logic filters the frame based on the Ethernet receive filter mode that has
been enabled. Filter modes are specified based on the state of the control bits in Table 3.1, "Address
Filtering Modes", which shows the various filtering modes used by the Ethernet MAC Function. These
bits are defined in more detail in the “MAC Control Register”. Please refer to Section 5.4.1,
"MAC_CR—MAC Control Register," on page 94 for more information on this register.
If the frame fails the filter, the Ethernet MAC function does not receive the packet. The host has the
option of accepting or ignoring the packet.
Table 3.1 Address Filtering Modes
MCPAS
PRMS
INVFILT
HO
HPFILT
DESCRIPTION
0
0
0
0
0
MAC address perfect filtering only
for all addresses.
0
0
0
0
1
MAC address perfect filtering for
physical address and hash filtering
for multicast addresses
0
0
0
1
1
Hash Filtering for physical and
multicast addresses
0
0
1
0
0
Inverse Filtering
X
1
0
X
X
Promiscuous
1
0
0
0
X
Pass all multicast frames. Frames
with physical addresses are
perfect-filtered
1
0
0
1
1
Pass all multicast frames. Frames
with physical addresses are hashfiltered
3.4
Filtering Modes
3.4.1
Perfect Filtering
This filtering mode passes only incoming frames whose destination address field exactly matches the
value programmed into the MAC Address High register and the MAC address low register. The MAC
address is formed by the concatenation of the above two registers in the MAC CSR Function.
3.4.2
Hash Only Filtering
This type of filtering checks for incoming Receive packets with either multicast or physical destination
addresses, and executes an imperfect address filtering against the hash table.
During imperfect hash filtering, the destination address in the incoming frame is passed through the
CRC logic and the upper six bits of the CRC register are used to index the contents of the hash table.
The hash table is formed by merging the register’s multicast hash table high and multicast hash table
low in the MAC CSR Function to form a 64-bit hash table. The most significant bit determines the
register to be used (High/Low), while the other five bits determine the bit within the register. A value
of 00000 selects Bit 0 of the multicast hash table low register and a value of 11111 selects Bit 31 of
the multicast hash table high register.
Revision 1.3 (05-31-07)
26
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.4.2.1
Hash Perfect Filtering
In hash perfect filtering, if the received frame is a physical address, the LAN9118 Packet Filter block
perfect-filters the incoming frame’s destination field with the value programmed into the MAC Address
High register and the MAC Address Low register. If the incoming frame is a multicast frame, however,
the LAN9118 packet filter function performs an imperfect address filtering against the hash table.
The imperfect filtering against the hash table is the same imperfect filtering process described in the
“Hash Only Filtering” section above.
3.4.2.2
Inverse Filtering
In inverse filtering, the LAN9118 Packet Filter Block accepts incoming frames with a destination
address not matching the perfect address (i.e., the value programmed into the MAC Address High
register and the MAC Address Low register in the CRC block and rejects frames with destination
addresses matching the perfect address.
For all filtering modes, when MCPAS is set, all multicast frames are accepted. When the PRMS bit is
set, all frames are accepted regardless of their destination address. This includes all broadcast frames
as well.
3.5
Wake-up Frame Detection
Setting the Wake-Up Frame Enable bit (WUEN) in the “WUCSR—Wake-up Control and Status
Register”, places the LAN9118 MAC in the wake-up frame detection mode. In this mode, normal data
reception is disabled, and detection logic within the MAC examines receive data for the preprogrammed wake-up frame patterns. The LAN9118 can be programmed to notify the host of the wakeup frame detection with the assertion of the host interrupt (IRQ) or assertion of the power managment
event signal (PME). Upon detection, the Wake-Up Frame Received bit (WUFR) in the WUCSR is set.
When the host clears the WUEN bit the LAN9118 will resume normal receive operation.
Before putting the MAC into the wake-up frame detection state, the host must provide the detection
logic with a list of sample frames and their corresponding byte masks. This information is written into
the Wake-up Frame Filter register (WUFF). Please refer to Section 5.4.11, "WUFF—Wake-up Frame
Filter," on page 102 for additional information on this register.
The MAC supports four programmable filters that support many different receive packet patterns. If
remote wake-up mode is enabled, the remote wake-up function receives all frames addressed to the
MAC. It then checks each frame against the enabled filter and recognizes the frame as a remote wakeup frame if it passes the wakeup frame filter register’s address filtering and CRC value match.
In order to determine which bytes of the frames should be checked by the CRC module, the MAC uses
a programmable byte mask and a programmable pattern offset for each of the four supported filters.
The pattern’s offset defines the location of the first byte that should be checked in the frame. Since
the destination address is checked by the address filtering Function, the pattern offset is always greater
than 12.
The byte mask is a 31-bit field that specifies whether or not each of the 31 contiguous bytes within
the frame, beginning in the pattern offset, should be checked. If bit j in the byte mask is set, the
detection logic checks byte offset +j in the frame. In order to load the Wake-up Frame Filter register,
the host LAN driver software must perform eight writes to the Wake-up Frame Filter register (WUFF).
The Diagram shown in Table 3.2, "Wake-Up Frame Filter Register Structure" below, shows the wakeup frame filter register’s structure.
Note 3.1
Wake-up frame detection can be performed when LAN9118 is in the D0 or D1 power
states. In the D0 state, wake-up frame detection is enabled when the WUEN bit is set.
Note 3.2
Wake-up frame detection, as well as Magic Packet detection, is always enabled and
cannot be disabled when the device enters the D1 state.
SMSC LAN9118
27
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 3.2 Wake-Up Frame Filter Register Structure
Filter 0 Byte Mask
Filter 1 Byte Mask
Filter 2 Byte Mask
Filter 3 Byte Mask
Reserved
Filter 3
Command
Reserved
Filter 3 Offset
Filter 2
Command
Reserved
Filter 2 Offset
Filter 1
Command
Filter 1Offset
Reserved
Filter 0
Command
Filter 0 Offset
Filter 1 CRC-16
Filter 0 CRC-16
Filter 3 CRC-16
Filter 2 CRC-16
The Filter i Byte Mask defines which incoming frame bytes Filter i will examine to determine whether
or not this is a wake-up frame. Table 3.3, describes the byte mask’s bit fields.
Table 3.3 Filter i Byte Mask Bit Definitions
FILTER I BYTE MASK DESCRIPTION
FIELD
31
30:0
DESCRIPTION
Must be zero (0)
Byte Mask: If bit j of the byte mask is set, the CRC machine processes byte number pattern - (offset
+ j) of the incoming frame. Otherwise, byte pattern - (offset + j) is ignored.
The Filter i command register controls Filter i operation. Table 3.4 shows the Filter I command register.
Table 3.4 Filter i Command Bit Definitions
FILTER i COMMANDS
FIELD
3
2:1
0
DESCRIPTION
Address Type: Defines the destination address type of the pattern. When bit is set, the pattern
applies
only to multicast frames. When bit is cleared, the pattern applies only to unicast frames.
RESERVED
Enable Filter: When bit is set, Filter i is enabled, otherwise, Filter i is disabled.
The Filter i Offset register defines the offset in the frame’s destination address field from which the
frames are examined by Filter i. Table 3.5 describes the Filter i Offset bit fields.
Revision 1.3 (05-31-07)
28
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 3.5 Filter i Offset Bit Definitions
FILTER I OFFSET DESCRIPTION
FIELD
DESCRIPTION
7:0
Pattern Offset: The offset of the first byte in the frame on which CRC is checked for wake-up frame
recognition. The minimum value of this field must be 12 since there should be no CRC check for
the destination address and the source address fields. The MAC checks the first offset byte of the
frame for CRC and checks to determine whether the frame is a wake-up frame. Offset 0 is the first
byte of the incoming frame's destination address.
The Filter i CRC-16 register contains the CRC-16 result of the frame that should pass Filter i.
Table 3.6 describes the Filter i CRC-16 bit fields.
Table 3.6 Filter i CRC-16 Bit Definitions
FILTER I CRC-16 DESCRIPTION
FIELD
DESCRIPTION
15:0
3.5.1
Pattern CRC-16: This field contains the 16-bit CRC value from the pattern and the byte mask
programmed to the wake-up filter register Function. This value is compared against the CRC
calculated on the incoming frame, and a match indicates the reception of a wakeup frame.
Magic Packet Detection
Setting the Magic Packet Enable bit (MPEN) in the “WUCSR—Wake-up Control and Status Register”,
places the LAN9118 MAC in the “Magic Packet” detection mode. In this mode, normal data reception
is disabled, and detection logic within the MAC examines receive data for a Magic Packet. The
LAN9118 can be programmed to notify the host of the “Magic Packet” detection with the assertion of
the host interrupt (IRQ) or assertion of the power managment event signal (PME). Upon detection, the
Magic Packet Received bit (MPR) in the WUCSR is set. When the host clears the MPEN bit the
LAN9118 will resume normal receive operation. Please refer to Section 5.4.12, "WUCSR—Wake-up
Control and Status Register," on page 103 for additional information on this register
In Magic Packet mode, the Power Management Logic constantly monitors each frame addressed to
the node for a specific Magic Packet pattern. It checks only packets with the MAC’s address or a
broadcast address to meet the Magic Packet requirement. The Power Management Logic checks each
received frame for the pattern 48h FF_FF_FF_FF_FF_FF after the destination and source address
field.
Then the Function looks in the frame for 16 repetitions of the MAC address without any breaks or
interruptions. In case of a break in the 16 address repetitions, the PMT Function scans for the
48'hFF_FF_FF_FF_FF_FF pattern again in the incoming frame.
The 16 repetitions may be anywhere in the frame but must be preceded by the synchronization stream.
The device will also accept a multicast frame, as long as it detects the 16 duplications of the MAC
address. If the MAC address of a node is 00h 11h 22h 33h 44h 55h, then the MAC scans for the
following data sequence in an Ethernet: Frame.
SMSC LAN9118
29
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Destination Address Source Address ……………FF FF FF FF FF FF
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
…CRC
It should be noted that Magic Packet detection can be performed when LAN9118 is in the D0 or D1
power states. In the D0 state, “Magic Packet” detection is enabled when the MPEN bit is set. In the
D1 state, Magic Packet detection, as well as wake-up frame detection, are automatically enabled when
the device enters the D1 state.
3.6
32-bit vs. 16-bit Host Bus Width Operation
The LAN9118 can be configured to communicate with the host bus via either a 32-bit or a 16-bit bus.
An external strap is used to select between the two modes. 32-bit mode is the native environment for
the LAN9118 Ethernet controller and no special requirements exist for communication in this mode.
However, when this part is used in the 16-bit mode, two writes or reads must be performed back to
back to properly communicate.
The bus width is set by strapping the EEDIO pin; this setting can be read from bit 2 of the “Hardware
Configuration Register”. Please refer to Section 5.3.9, "HW_CFG—Hardware Configuration Register,"
on page 77 for additional information on this register.
3.6.1
16-bit Bus Writes
The host processor is required to perform two contiguous 16-bit writes to complete a single DWORD
transfer. This DWORD must begin and end on a DWORD address boundary (A[2] and higher, cannot
change during a sixteen bit write). No ordering requirements exist. The processor can access either
the low or high word first, as long as the next write is performed to the other word. If a write to the
same word is performed, the LAN9118 disregards the transfer.
3.6.2
16-bit Bus Reads
The host processor is required to perform two consecutive 16-bit reads to complete a single DWORD
transfer. This DWORD must begin and end on a DWORD address boundary (A[2] and higher, cannot
change during a sixteen bit read). No ordering requirements exist. The processor can access either
the low or high word first, as long as the next read is performed from the other word. If a read to the
same word is performed, the data read is invalid and should be re-read. This is not a fatal error. The
LAN9118 will reset its read counters and restart a new cycle on the next read. The Upper 16 data pins
(D[31:16]) are not driven by the LAN9118 in 16-bit mode. These pins have internal pull-down’s and the
signals are left in a high-impedance state.
3.7
Big and Little Endian Support
The SMSC LAN9118 supports “Big-” or “Little-Endian” processors in either 16 or 32-bit bus width
modes. To support big-endian processors, the hardware designer must explicitly invert the layout of
the byte lanes. In addition, for a 16-bit interface, the WORD_SWAP—Word Swap Control must be set
correctly following Table 3.7, "Byte Lane Mapping".
The host bus interface can be selected via an external strap to translate the data bus into either mode.
Please refer to Table 2.4, “Serial EEPROM Interface Signals,” on page 16, for information on
multiplexed signal D32/nD16 for more information on data bus width selection.
Revision 1.3 (05-31-07)
30
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Additionally, please refer to Section 5.3.17, "WORD_SWAP—Word Swap Control," on page 86 for
additional information on status indication on Endian modes.
Table 3.7 Byte Lane Mapping
DATA PINS
MODE OF
OPERATION
32-bit
D[31:24]
D[23:16]
D[15:8]
D[7:0]
DESCRIPTION
Byte 3
(MSB)
Byte 2
Byte 1
Byte 0
(LSB)
This is the native mode of the LAN9118.
Endianess does not matter when both
WORD lanes are in operation.
Mode 0 (WORD_SWAP—Word Swap Control equal to FFFFFFFFh)
A1 = 0
--
--
Byte 3
Byte 2
A1 = 1
--
--
Byte 1
Byte 0
Note:
This mode can be used by 32bit processors operating with
an external 16-bit bus.
Mode 1 (WORD_SWAP—Word Swap Control not equal to FFFFFFFFh)
A1 = 0
--
--
Byte 1
Byte 0
A1 = 1
--
--
Byte 3
Byte 2
Note:
This mode can also be used
by native 16-bit processors.
Regarding the 32-bit mode description of operation comment described in the table above, mentioning
“It should be noted that Endianess does not matter when both WORD lanes are in operation” is true
for the LAN9118 device. However, as in all designs, it is important for the PCB layout designer to route
the signal byte lanes appropriately relative to the processor type (Big vs. Little Endian).
3.8
General Purpose Timer (GP Timer)
The General Purpose Timer is a programmable block that can be used to generate periodic host
interrupts. The resolution of this timer is 100uS.
The GP Timer loads the GPT_CNT Register with the value in the GPT_LOAD field and begins counting
down when the TIMER_EN bit is set to a ‘1.’ On a reset, or when the TIMER_EN bit changes from
set ‘1’ to cleared ‘0,’ the GPT_CNT field is initialized to FFFFh. The GPT_CNT register is also initialized
to FFFFh on a reset. Software can write the pre-load value into the GPT_LOAD field at any time; e.g.,
before or after the TIMER_EN bit is asserted. The GPT Enable bit TIMER_EN is located in the
GPT_CFG register.
Once enabled, the GPT counts down either until it reaches 0000h or until a new pre-load value is
written to the GPT_LOAD field. At 0000h, the counter wraps around to FFFFh, asserts the GPT
interrupt status bit and the IRQ signal if the GPT_INT_EN bit is set, and continues counting. The GPT
interrupt status bit is in the INT_STS Register. The GPT_INT hardware interrupt can only be set if the
GPT_INT_EN bit is set. GPT_INT is a sticky bit (R/WC); i.e., once the GPT_INT bit is set, it can only
be cleared by writing a ‘1’ to the bit.
3.9
EEPROM Interface
LAN9118 can optionally load its MAC address from an external serial EEPROM. If a properly
configured EEPROM is detected by LAN9118 at power-up, hard reset or soft reset, the ADDRH and
ADDRL registers will be loaded with the contents of the EEPROM. If a properly configured EEPROM
is not detected, it is the responsibility of the host LAN Driver to set the IEEE addresses.
The LAN9118 EEPROM controller also allows the host system to read, write and erase the contents
of the Serial EEPROM. The EEPROM controller supports most “93C46” type EEPROMs configured for
128 x 8-bit operation.
SMSC LAN9118
31
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.9.1
MAC Address Auto-Load
On power-up, hard reset or soft reset, the EEPROM controller attempts to read the first byte of data
from the EEPROM (address 00h). If the value A5h is read from the first address, then the EEPROM
controller will assume that an external Serial EEPROM is present. The EEPROM controller will then
access the next EEPROM byte and send it to the MAC Address register byte 0 (ADDRL[7:0]). This
process will be repeated for the next five bytes of the MAC Address, thus fully programming the 48bit MAC address. Once all six bytes have been programmed, the “MAC Address Loaded” bit is set in
the E2P_CMD register. A detailed explanation of the EEPROM byte ordering with respect to the MAC
address is given in Section 5.4.3, "ADDRL—MAC Address Low Register," on page 97.
If an 0xA5h is not read from the first address, the EEPROM controller will end initialization. It is then
the responsibility of the host LAN driver software to set the IEEE address by writing to the MAC’s
ADDRH and ADDRL registers.
The host can initiate a reload of the MAC address from the EEPROM by issuing the RELOAD
command via the E2P command (E2P_CMD) register. If the first byte read from the EEPROM is not
A5h, it is assumed that the EEPROM is not present, or not programmed, and the MAC address reload
will fail. The “MAC Address Loaded” bit indicates a successful reload of the MAC address.
3.9.2
EEPROM Host Operations
After the EEPROM controller has finished reading (or attempting to read) the MAC after power-on, hard
reset or soft reset, the host is free to perform other EEPROM operations. EEPROM operations are
performed using the E2P_CMD and E2P data (E2P_DATA) registers. Section 5.3.23, "E2P_CMD –
EEPROM Command Register," on page 91 provides an explanation of the supported EEPROM
operations.
If the EEPROM operation is the “write location” (WRITE) or “write all” (WRAL) commands, the host
must first write the desired data into the E2P_DATA register. The host must then issue the WRITE or
WRAL command using the E2P_CMD register by setting the EPC_CMD field appropriately. If the
operation is a WRITE, the EPC_ADDR field in E2P_CMD must also be set to the desired location. The
command is executed when the host sets the EPC_BSY bit high. The completion of the operation is
indicated when the EPC_BSY bit is cleared.
If the EEPROM operation is the “read location” (READ) operation, the host must issue the READ
command using the E2P_CMD with the EPC_ADDR set to the desired location. The command is
executed when the host sets the EPC_BSY bit high. The completion of the operation is indicated when
the EPC_BSY bit is cleared, at which time the data from the EEPROM may be read from the
E2P_DATA register.
Other EEPROM operations are performed by writing the appropriate command to the EPC_CMD
register. The command is executed when the host sets the EPC_BSY bit high. The completion of the
operation is indicated when the EPC_BSY bit is cleared. In all cases the host must wait for EPC_BSY
to clear before modifying the E2P_CMD register.
Note: The EEPROM device powers-up in the erase/write disabled state. To modify the contents of
the EEPROM the host must first issue the EWEN command.
If an operation is attempted, and an EEPROM device does not respond within 30mS, the LAN9118
will timeout, and the EPC timeout bit (EPC_TO) in the E2P_CMD register will be set.
Figure 3.3, "EEPROM Access Flow Diagram" illustrates the host accesses required to perform an
EEPROM Read or Write operation.
Revision 1.3 (05-31-07)
32
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
EEPROM Write
EEPROM Read
Idle
Idle
Write Data
Register
Write
Command
Register
Write
Command
Register
Read
Command
Register
Busy Bit = 0
Busy Bit = 0
Read
Command
Register
Read Data
Register
Figure 3.3 EEPROM Access Flow Diagram
The host can disable the EEPROM interface through the GPIO_CFG register. When the interface is
disabled, the EEDIO and ECLK signals can be used as general-purpose outputs, or they may be used
to monitor internal MII signals.
3.9.2.1
Supported EEPROM Operations
The EEPROM controller supports the following EEPROM operations under host control via the
E2P_CMD register. The operations are commonly supported by “93C46” EEPROM devices. A
description and functional timing diagram is provided below for each operation. Please refer to the
E2P_CMD register description in Section 5.3.23, "E2P_CMD – EEPROM Command Register," on
page 91 for E2P_CMD field settings for each command.
ERASE (Erase Location): If erase/write operations are enabled in the EEPROM, this command will
erase the location selected by the EPC Address field (EPC_ADDR). The EPC_TO bit is set if the
EEPROM does not respond within 30ms.
SMSC LAN9118
33
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
1
1
A6
A0
EEDIO (INPUT)
Figure 3.4 EEPROM ERASE Cycle
ERAL (Erase All): If erase/write operations are enabled in the EEPROM, this command will initiate a
bulk erase of the entire EEPROM.The EPC_TO bit is set if the EEPROM does not respond within
30ms.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
0
0
1
0
EEDIO (INPUT)
Figure 3.5 EEPROM ERAL Cycle
Revision 1.3 (05-31-07)
34
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
EWDS (Erase/Write Disable): After issued, the EEPROM will ignore erase and write commands. To
re-enable erase/write operations issue the EWEN command.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
0
0
0
0
EEDIO (INPUT)
Figure 3.6 EEPROM EWDS Cycle
EWEN (Erase/Write Enable): Enables the EEPROM for erase and write operations. The EEPROM
will allow erase and write operations until the “Erase/Write Disable” command is sent, or until power
is cycled.
Note: The EEPROM device will power-up in the erase/write-disabled state. Any erase or write
operations will fail until an Erase/Write Enable command is issued.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
0
0
1
1
EEDIO (INPUT)
Figure 3.7 EEPROM EWEN Cycle
SMSC LAN9118
35
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
READ (Read Location): This command will cause a read of the EEPROM location pointed to by EPC
Address (EPC_ADDR). The result of the read is available in the E2P_DATA register.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
1
0
A6
A0
EEDIO (INPUT)
D7
D0
Figure 3.8 EEPROM READ Cycle
WRITE (Write Location): If erase/write operations are enabled in the EEPROM, this command will
cause the contents of the E2P_DATA register to be written to the EEPROM location selected by the
EPC Address field (EPC_ADDR). The EPC_TO bit is set if the EEPROM does not respond within
30ms.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
0
1
A6
A0
D7
D0
EEDIO (INPUT)
Figure 3.9 EEPROM WRITE Cycle
Revision 1.3 (05-31-07)
36
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
WRAL (Write All): If erase/write operations are enabled in the EEPROM, this command will cause the
contents of the E2P_DATA register to be written to every EEPROM memory location. The EPC_TO bit
is set if the EEPROM does not respond within 30ms.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
0
0
0
D7
1
D0
EEDIO (INPUT)
Figure 3.10 EEPROM WRAL Cycle
Table 3.8, "Required EECLK Cycles", shown below, shows the number of EECLK cycles required for
each EEPROM operation.
Table 3.8 Required EECLK Cycles
3.9.2.2
OPERATION
REQUIRED EECLK CYCLES
ERASE
10
ERAL
10
EWDS
10
EWEN
10
READ
18
WRITE
18
WRAL
18
MAC Address Reload
The MAC address can be reloaded from the EEPROM via a host command to the E2P_CMD register.
If a value of 0xA5h is not found in the first address of the EEPROM, the EEPROM is assumed to be
un-programmed and MAC Address Reload operation will fail. The “MAC Address Loaded” bit indicates
a successful load of the MAC address. The EPC_LOAD bit is set after a successful reload of the MAC
address.
3.9.2.3
EEPROM Command and Data Registers
Refer to Section 5.3.23, "E2P_CMD – EEPROM Command Register," on page 91 and Section 5.3.24,
"E2P_DATA – EEPROM Data Register," on page 93 for a detailed description of these registers.
Supported EEPROM operations are described in these sections.
3.9.2.4
EEPROM Timing
Refer to Section 6.9, "EEPROM Timing," on page 121 for detailed EEPROM timing specifications.
SMSC LAN9118
37
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.10
Power Management
LAN9118 supports power-down modes to allow applications to minimize power consumption. The
following sections describe these modes.
3.10.1
System Description
Power is reduced to various modules by disabling the clocks as outlined in Table 3.9, “Power
Management States,” on page 39. All configuration data is saved when in either of the two low power
states. Register contents are not affected unless specifically indicated in the register description.
3.10.2
Functional Description
There is one normal operating power state, D0 and there are two power saving states: D1, and D2.
Upon entry into either of the two power saving states, only the PMT_CTRL register is accessible for
read operations. In either of the power saving states the READY bit in the PMT_CTRL register will be
cleared. Reads of any other addresses are forbidden until the READY bit is set. All writes, with the
exception of the wakeup write to BYTE_TEST, are also forbidden until the READY bit is set. Only when
in the D0 (Normal) state, when the READY bit is set, can the rest of the device be accessed.
Note 3.3
The LAN9118 must always be read at least once after power-up, reset, or upon return from
a power-saving state, otherwise write operations will not function.
In system configurations where the PME signal is shared amongst multiple devices, the WUPS field
within the PMT_CTRL register can be read to determine which LAN9118 device is driving the PME
signal.
When the LAN9118 is in a power saving state (D1 or D2), a write cycle to the BYTE_TEST register
will return the LAN9118 to the D0 state. Table 7.1, “Power Consumption Device Only,” on page 124
and Table 7.2, “Power Consumption Device and System Components,” on page 125, shows the power
consumption values for each power state.
Note 3.4
3.10.2.1
When the LAN9118 is in a power saving state, a write of any data to the BYTE_TEST
register will wake-up the device. DO NOT PERFORM WRITES TO OTHER
ADDRRESSES while the READY bit in the PMT_CTRL register is cleared.
D1 Sleep
Power consumption is reduced in this state by disabling clocks to portions of the internal logic as
shown in Table 3.9. In this mode the clock to the internal PHY and portions of the MAC are still
operational. This state is entered when the host writes a '01' to the PM_MODE bits in the Power
Management (PMT_CTRL) register. The READY bit in PMT_CTRL is cleared when entering the D1
state.
Wake-up frame and Magic Packet detection are automatically enabled in the D1 state. If properly
enabled via the WOL_EN and PME_EN bits, the LAN9118 will assert the PME hardware signal upon
the detection of the wake-up frame or magic packet. The LAN9118 can also assert the host interrupt
(IRQ) on detection of a wake-up frame or magic packet. Upon detection, the WUPS field in PMT_CTRL
will be set to a 10b.
Note 3.5
The PME interrupt status bit (PME_INT) in the INT_STS register is set regardless of the
setting of PME_EN.
Note 3.6
Wake-up frame and Magic Packet detection is automatically enabled when entering the D1
state. For wake-up frame detection, the wake-up frame filter must be programmed before
entering the D1 state (see Section 3.5, "Wake-up Frame Detection," on page 27). If used,
the host interrupt and PME signal must be enabled prior to entering the D1 state.
A write to the BYTE_TEST register, regardless of whether a wake-up frame or Magic Packet was
detected, will return LAN9118 to the D0 state and will reset the PM_MODE field to the D0 state. As
noted above, the host is required to check the READY bit and verify that it is set before attempting
any other reads or writes of the device.
Revision 1.3 (05-31-07)
38
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Note 3.7
The host must do only read accesses prior to the ready bit being set.
Once the READY bit is set, the LAN9118 is ready to resume normal operation. At this time the WUPS
field can be cleared.
3.10.2.2
D2 Sleep
In this state, as shown in Table 3.9, all clocks to the MAC and host bus are disabled, and the PHY is
placed in a reduced power state. To enter this state, the EDPWRDOWN bit in register 17 of the PHY
(Mode Control/Status register) must be set. This places the PHY in the Energy Detect mode. The
PM_MODE bits in the PMT_CTRL register must then be set to 10b. Upon setting the PM_MODE bits,
the LAN9118 will enter the D2 sleep state. The READY bit in PMT_CTRL is cleared when entering the
D2 state.
Note 3.8
If carrier is present when this state is entered detection will occur immediately.
If properly enabled via the ED_EN and PME_EN bits, LAN9118 will assert the PME hardware signal
upon detection of a valid carrier. Upon detection, the WUPS field in PMT_CTRL will be set to a 01b.
Note 3.9
The PME interrupt status bit on the INT_STS register (PME_INT) is set regardless of the
setting of PME_EN.
A write to the BYTE_TEST register, regardless of whether a carrier was detected, will return LAN9118
to the D0 state and will reset the PM_MODE field to the D0 state. As noted above, the host is required
to check the READY bit and verify that it is set before attempting any other reads or writes of the
device. Before LAN9118 is fully awake from this state the EDPWRDOWN bit in register 17 of the PHY
must be cleared in order to wake the PHY. Do not attempt to clear the EDPWRDOWN bit until the
READY bit is set. After clearing the EDPWRDOWN bit the LAN9118 is ready to resume normal
operation. At this time the WUPS field can be cleared.
Table 3.9 Power Management States
Device
BLOCK
D0
(NORMAL OPERATION)
D1
(WOL)
D2
(ENERGY DETECT)
PHY
Full ON
Full ON
Energy Detect Power-Down
MAC Power
Management
Full ON
RX Power Mgmt. Block
On
OFF
MAC and Host
Interface
Full ON
OFF
OFF
Internal Clock
Full ON
Full ON
OFF
KEY
CLOCK ON
BLOCK DISABLED – CLOCK ON
FULL OFF
SMSC LAN9118
39
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.10.2.3
Power Managment Event Indicators
Figure 3.11 is a simplified block diagram of the logic that controls the external PME, and internal
pme_interrupt signals. The pme_interrupt signal is used to set the PME_INT status bit in the INT_STS
register, which, if enabled, will generate a host interrupt upon detection of a power management event.
The PME_INT status bit in INT_STS will remain set until the internal pme_interrupt signal is cleared
by clearing the WUPS bits, or by clearing the corresponding WOL_EN or ED_EN bit. After clearing the
internal pme_interrupt signal, the PME_INT status bit may be cleared by writing a ‘1’ to this bit in the
INT_STS register. It should be noted that the LAN9118 can generate a host interrupt regardless of the
state of the PME_EN bit, or the external PME signal.
The external PME signal can be setup for pulsed, or static operation. When the PME_IND bit in the
PMT_CTRL register is set to a ‘1’, the external PME signal will be driven active for 50ms upon
detection of a wake-up event. When the PME_IND bit is cleared, the PME signal will be driven
continously upon detection of a wake-up event. The PME signal is deactivated by clearing the WUPS
bits, or by clearing the corresponding WOL_EN or ED_EN bit. The PME signal can also be deactivated
by clearing the PME_EN bit.
WUFR
WOL_EN
WUEN
WUPS
MPR
ED_EN
MPEN
WUPS
phy_int
Other System
Interrupts
PME_INT
IRQ
Denotes a level-triggered "sticky" status bit
PME_INT_EN
IRQ_EN
50ms
PME_EN
PME
LOGIC
PME_IND
PME_POL
PME_TYPE
Figure 3.11 PME and PME_INT Signal Generation
3.10.3
Internal PHY Power-Down modes
There are 2 power-down modes for the internal Phy:
3.10.3.1
General Power-Down
This power-down is controlled by register 0, bit 11. In this mode the internal PHY, except the
management interface, is powered-down and stays in that condition as long as Phy register bit 0.11 is
HIGH. When bit 0.11 is cleared, the PHY powers up and is automatically reset. Please refer to Section
5.5.1, "Basic Control Register," on page 104 for additional information on this register.
Revision 1.3 (05-31-07)
40
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.10.3.2
Energy Detect Power-Down
This power-down mode is activated by setting the Phy register bit 17.13 to 1. Please refer to Section
5.5.8, "Mode Control/Status," on page 108 for additional information on this register. In this mode when
no energy is present on the line, the PHY is powered down, with th exception of the management
interface, the SQUELCH circuit and the ENERGYON logic. The ENERGYON logic is used to detect
the presence of valid energy from 100Base-TX, 10Base-T, or Auto-negotiation signals
In this mode, when the ENERGYON signal is low, the PHY is powered-down, and nothing is
transmitted. When energy is received - link pulses or packets - the ENERGYON signal goes high, and
the PHY powers-up. It automatically resets itself into the state it had prior to power-down, and asserts
the INT7.1 bit of the register defined in Section 5.5.11, "Interrupt Source Flag," on page 110. If the
ENERGYON interrupt is enabled, this event will cause an interrupt to the host. The first and possibly
the second packet to activate ENERGYON may be lost.
When 17.13 is low, energy detect power-down is disabled.
3.11
Detailed Reset Description
The LAN9118 has five reset sources:
„
Power-On Reset (POR)
„
Hardware Reset Input Pin (nRESET)
„
Soft Reset (SRST)
„
PHY Soft Reset via PMT_CTRL bit 10 (PHY_RST)
„
PHY Soft Reset via PHY Basic Control Register (PHY REG 0.15)
Table 3.10 shows the effect of the various reset sources on the LAN9118's circuitry.
Table 3.10 Reset Sources and Affected Circuitry
MAC
PHY
Note 3.10
EEPROM MAC
ADDR.
RELOAD
Note 3.11
CONFIG.
STRAPS
LATCHED
X
X
X
X
X
X
X
X
X
X
X
X
PLL
HBI
Note
3.12
NASR
REGISTERS
Note 3.12
MIL
POR
X
X
X
nRESET
X
X
X
RESET
SOURCE
SRST
X
X
PHY_RST
X
PHY REG 0.15
X
Note 3.10 After any PHY reset, the application must wait until the “Link Status” bit in the PHY’s “Basic
Status Register” (PHY Reg. 1.2) is set before attempting to transmit or receive data.
Note 3.11 After a POR, nRESET or SRST, the LAN9118 will automatically check for the presence of
an external EEPROM. After any of these resets the application must verify that the EPC
Busy Bit (E2P_CMD, bit 31) is cleared before attempting to access the EEPROM, or
change the function of the GPO/GPIO signals, or before modifying the ADDRH or ADDRL
registers in the MAC.
Note 3.12 HBI - “Host Bus Interface”, NASR - Not affected by software reset.
SMSC LAN9118
41
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.11.1
Power-On Reset (POR)
A Power-On reset occurs whenever power is initially applied to the LAN9118, or if power is removed
and reapplied to the LAN9118. A timer within the LAN9118 will assert the internal reset for
approximately 22ms. The READY bit in the PMT_CTRL register can be read from the host interface
and will read back a ‘0’ until the POR is complete. Upon completion of the POR, the READY bit in
PMT_CTRL is set high, and the LAN9118 can be configured via its control registers.
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) after an internal
reset (22ms). If the software driver polls this bit and it is not set within 100ms, then an error
condition occurred.
3.11.2
Hardware Reset Input (nRESET)
A hardware reset will occur when the nRESET input signal is driven low. The READY bit in the
PMT_CTRL register can be read from the host interface, and will read back a ‘0’ until the hardware
reset is complete. Upon completion of the hardware reset, the READY bit in PMT_CTRL is set high.
After the “READY” bit is set, the LAN9118 can be configured via its control registers. The nRESET
signal is pulled-high internally by the LAN9118 and can be left unconnected if unused. If used, nRESET
must be driven low for a minimum period as defined in Section 6.8, "Reset Timing," on page 121.
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) immediately. If
the software driver polls this bit and it is not set within 100ms, then an error condition
occurred.
3.11.3
Resume Reset Timing
After issuing a write to the BYTE_TEST register to wake the LAN9118 from a power-down state, the
READY bit in PMT_CTRL will assert (set High) within 2ms.
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) within 2 ms. If
the software driver polls this bit and it is not set within 100ms, then an error condition
occurred.
3.11.4
Soft Reset (SRST)
Soft reset is initiated by writing a ‘1’ to bit 0 of the HW_CFG register (SRST). This self-clearing bit will
return to ‘0’ after approximately 2 μs, at which time the Soft Reset is complete. Soft reset does not
clear control register bits marked as NASR.
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) immediately,
(within 2μs). If the software driver polls this bit and it is not set within 100ms, then an error
condition occurred.
3.11.5
PHY Reset Timing
The following sections and tables specify the operation and time required for the internal PHY to
become operational after various resets or when returning from the reduced power state.
3.11.5.1
PHY Soft Reset via PMT_CTRL bit 10 (PHY_RST)
The PHY soft reset is initiated by writing a ‘1’ to bit 10 of the PMT_CTRL register (PHY_RST). This
self-clearing bit will return to ‘0’ after approximately 100 μs, at which time the PHY reset is complete.
3.11.5.2
PHY Soft Reset via PHY Basic Control Register (PHY Reg. 0.15)
The PHY Reg. 0.15 Soft Reset is initiated by writing a ‘1’ to bit 15 of the PHY’s Basic Control Register.
This self-clearing bit will return to ‘0’ at which time the PHY reset is complete.
Revision 1.3 (05-31-07)
42
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.12
TX Data Path Operation
Data is queued for transmission by writing it into the TX data FIFO. Each packet to be transmitted may
be divided among multiple buffers. Each buffer starts with a two DWORD TX command (TX command
‘A’ and TX command ‘B’). The TX command instructs the LAN9118 on the handling of the associated
buffer. Packet boundaries are delineated using control bits within the TX command.
The host provides a 16-bit Packet Tag field in the TX command. The Packet Tag value is appended
to the corresponding TX status DWORD. All Packet Tag fields must have the same value for all buffers
in a given packet. If tags differ between buffers in the same packet the TXE error will be asserted. Any
value may be chosen for a Packet Tag as long as all tags in the same Packet are identical. Packet
Tags also provide a method of synchronization between transmitted packets and their associated
status. Software can use unique Packet Tags to assist with validating matching status completions.
Note 3.13 The use of packet tags is not required by the hardware. This is a software LAN driver only
application example for use of this field.
A Packet Length field in the TX command specifies the number of bytes in the associated packet. All
Packet Length fields must have the same value for all buffers in a given packet. Hardware compares
the Packet Length field and the actual amount of data received by the Ethernet controller. If the actual
packet length count does not match the Packet Length field as defined in the TX command, the
Transmitter Error (TXE) flag is asserted.
The LAN9118 can be programmed to start payload transmission of a buffer on a byte boundary by
setting the “Data Start Offset” field in the TX command. The “Data Start Offset” field points to the actual
start of the payload data within the first 8 DWORDs of the buffer. Data before the “Data Start Offset”
pointer will be ignored. When a packet is split into multiple buffers, each successive buffer may begin
on any arbitrary byte.
The LAN9118 can be programmed to strip padding from the end of a transmit packet in the event that
the end of the packet does not align with the host burst boundary. This feature is necessary when the
LAN9118 is operating in a system that always performs multi-word bursts. In such cases the LAN9118
must guarantee that it can accept data in multiples of the Burst length regardless of the actual packet
length. When configured to do so, the LAN9118 will accept extra data at the end of the packet and will
remove the extra padding before transmitting the packet. The LAN9118 automatically removes data up
to the boundary specified in the Buffer End Alignment field specified in each TX command.
The host can instruct the LAN9118 to issue an interrupt when the buffer has been fully loaded into the
TX FIFO contained in the LAN9118 and transmitted. This feature is enabled through the TX command
‘Interrupt on Completion’ field.
Upon completion of transmission, irrespective of success or failure, the status of the transmission is
written to the TX status FIFO. TX status is available to the host and may be read using PIO operations.
An interrupt can be optionally enabled by the host to indicate the availability of a programmable
number TX status DWORDS.
Before writing the TX command and payload data to the TX FIFO, the host must check the available
TX FIFO space by performing a PIO read of the TX_FIFO_INF register. The host must ensure that it
does not overfill the TX FIFO or the TX Error (TXE) flag will be asserted.
The host proceeds to write the TX command by first writing TX command ‘A’, then TX command ‘B’.
After writing the command, the host can then move the payload data into the TX FIFO. TX status
DWORD’s are stored in the TX status FIFO to be read by the host at a later time upon completion of
the data transmission onto the wire.
SMSC LAN9118
43
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
init
Idle
TX Status
Available
Check
available
FIFO
space
Read TX
Status
(optional)
Write
TX
Command
Write
Start
Padding
(optional)
Last Buffer in
Packet
Not Last Buffer
Write
Buffer
Figure 3.12 Simplified Host TX Flow Diagram
Revision 1.3 (05-31-07)
44
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.12.1
TX Buffer Format
TX buffers exist in the host’s memory in a given format. The host writes a TX command word into the
TX data buffer before moving the Ethernet packet data. The TX command A and command B are 32bit values that are used by the LAN9118 in the handling and processing of the associated Ethernet
packet data buffer. Buffer alignment, segmentation and other packet processing parameters are
included in the command structure. The following diagram illustrates the buffer format.
Host Write
31
Order
0
1st
TX Command 'A'
2nd
TX Command 'B'
3rd
Optional offset DWORD0
.
.
.
Optional offset DWORDn
Offset + Data DWORD0
.
.
.
.
.
Last Data & PAD
Optional Pad DWORD0
.
.
.
Optional Pad DWORDn
Last
Figure 3.13 TX Buffer Format
Figure 3.13, "TX Buffer Format", shows the TX Buffer as it is written into the LAN9118. It should be
noted that not all of the data shown in this diagram is actually stored in the TX data FIFO. This must
be taken into account when calculating the actual TX data FIFO usage. Please refer to Section 3.12.5,
"Calculating Actual TX Data FIFO Usage," on page 49 for a detailed explanation on calculating the
actual TX data FIFO usage.
3.12.2
TX Command Format
The TX command instructs the TX FIFO controller on handling the subsequent buffer. The command
precedes the data to be transmitted. The TX command is divided into two, 32-bit words; TX command
‘A’ and TX command ‘B’.
There is a 16-bit packet tag in the TX command ‘B’ command word. Packet tags may, if host software
desires, be unique for each packet (i.e., an incrementing count). The value of the tag will be returned
in the RX status word for the associated packet. The Packet tag can be used by host software to
uniquely identify each status word as it is returned to the host.
SMSC LAN9118
45
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Both TX command ‘A’ and TX command ‘B’ are required for each buffer in a given packet. TX
command ‘B’ must be identical for every buffer in a given packet. If the TX command ‘B’ words do not
match, the Ethernet controller will assert the Transmitter Error (TXE) flag.
TX COMMAND ‘A’
Table 3.11 TX Command 'A' Format
BITS
DESCRIPTION
31
Interrupt on Completion. When set, the TXDONE flag will be asserted when the current buffer has
been fully loaded into the TX FIFO. This flag may be optionally mapped to a host interrupt.
30:26
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
25:24
Buffer End Alignment. This field specifies the alignment that must be maintained on the last data
transfer of a buffer. The host will add extra DWORDs of data up to the alignment specified in the
table below. The LAN9118 will remove the extra DWORDs. This mechanism can be used to maintain
cache line alignment on host processors.
[25]
[24]
End Alignment
0
0
4-byte alignment
0
1
16-byte alignment
1
0
32-byte alignment
1
1
Reserved
23:21
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility
20:16
Data Start Offset (bytes). This field specifies the offset of the first byte of TX data. The offset value
can be anywhere from 0 bytes to 31 a Byte offset.
15:14
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility
13
First Segment. When set, this bit indicates that the associated buffer is the first segment of the
packet.
12
Last Segment. When set, this bit indicates that the associated buffer is the last segment of the
packet
11
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
10:0
Buffer Size (bytes). This field indicates the number of bytes contained in the buffer following this
command. This value, along with the Buffer End Alignment field, is read and checked by the LAN9118
and used to determine how many extra DWORD’s were added to the end of the Buffer. A running
count is also maintained in the LAN9118 of the cumulative buffer sizes for a given packet. This
cumulative value is compared against the Packet Length field in the TX command ‘B’ word and if
they do not correlate, the TXE flag is set.
Note:
Revision 1.3 (05-31-07)
The buffer size specified does not include the buffer end alignment padding or data start
offset added to a buffer.
46
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
TX COMMAND ‘B’
Table 3.12 TX Command 'B' Format
BITS
DESCRIPTION
31:16
Packet Tag. The host should write a unique packet identifier to this field. This identifier is added to
the corresponding TX status word and can be used by the host to correlate TX status words with
their corresponding packets.
Note:
15:14
The use of packet tags is not required by the hardware. This field can be used by the LAN
software driver for any application. Packet Tags is one application example.
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
13
Add CRC Disable. When set, the automatic addition of the CRC is disabled.
12
Disable Ethernet Frame Padding. When set, this bit prevents the automatic addition of padding to
an Ethernet frame of less than 64 bytes. The CRC field is also added despite the state of the Add
CRC Disable field.
11
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
10:0
Packet Length (bytes). This field indicates the total number of bytes in the current packet. This
length does not include the offset or padding. If the Packet Length field does not match the actual
number of bytes in the packet the Transmitter Error (TXE) flag will be set.
3.12.3
TX Data Format
The TX data section begins at the third DWORD in the TX buffer (after TX command ‘A’ and TX
command ‘B’). The location of the first byte of valid buffer data to be transmitted is specified in the
“Data Start Offset” field of the TX command ‘A’ word. Table 3.13, "TX DATA Start Offset", shows the
correlation between the setting of the LSB’s in the “Data Start Offset” field and the byte location of the
first valid data byte. Additionally, transmit buffer data can be offset by up to 7 additional DWORDS as
indicated by the upper three MSB’s (5:2) in the “Data Start Offset” field.
Table 3.13 TX DATA Start Offset
Data Start Offset [1:0]:
First TX Data Byte:
11
D[31:24]
10
D[23:16]
01
D[15:8]
00
D[7:0]
TX data is contiguous until the end of the buffer. The buffer may end on a byte boundary. Unused
bytes at the end of the packet will not be sent to the MIL for transmission.
The Buffer End Alignment field in TX command ‘A’ specifies the alignment that must be maintained for
the associated buffer. End alignment may be specified as 4-, 16-, or 32-byte. The host processor is
responsible for adding the additional data to the end of the buffer. The hardware will automatically
remove this extra data.
3.12.3.1
TX Buffer Fragmentation Rules
Transmit buffers must adhere to the following rules:
„
Each buffer can start and end on any arbitrary byte alignment
„
The first buffer of any transmit packet can be any length
„
Middle buffers (i.e., those with First Segment = Last Segment = 0) must be greater than, or equal
to 4 bytes in length
„
The final buffer of any transmit packet can be any length
SMSC LAN9118
47
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Additionally, The LAN9118 has specific rules regarding the use of transmit buffers when in Store-andForward mode (i.e., HW_CFG[SF] = 1). When this mode is enabled, the total space consumed in the
TX FIFO (MIL) must be limited to no more than 2KB - 3 DWORDs (2,036 bytes total). Any transmit
packet that is so highly fragmented that it takes more space than this must be un-fragmented (by
copying to a Driver-supplied buffer) before the transmit packet can be sent to the LAN9118.
One approach to determine whether a packet is too fragmented is to calculate the actual amount of
space that it will consume, and check it against 2,036 bytes. Another approach is to check the number
of buffers against a worst-case limit of 86 (see explanation below).
3.12.3.2
Calculating Worst-Case TX FIFO (MIL) Usage
The actual space consumed by a buffer consists only of any partial DWORD offsets in the first/last
DWORD of the buffer, plus all of the whole DWORDs in between. Any whole DWORD offsets and/or
alignments are stripped off before the buffer even gets into the TX data FIFO, and TX command words
are stripped off before the buffer is written to the TX FIFO, so none of those DWORDs count as space
consumed. The worst-case overhead for a TX buffer is 6 bytes, which assumes that it started on the
high byte of a DWORD and ended on the low byte of a DWORD. A TX packet consisting of 86 such
fragments would have an overhead of 516 bytes (6 * 86) which, when added to a 1514-byte max-size
transmit packet (1516 bytes, rounded up to the next whole DWORD), would give a total space
consumption of 2,032 bytes, leaving 4 bytes to spare; this is the basis for the "86 fragment" rule
mentioned above.
3.12.4
TX Status Format
TX status is passed to the host CPU through a separate FIFO mechanism. A status word is returned
for each packet transmitted. Data transmission is suspended if the TX status FIFO becomes full. Data
transmission will resume when the host reads the TX status and there is room in the FIFO for more
“TX Status” data.
The host can optionally choose to not read the TX status. The host can optionally ignore the TX status
by setting the “TX Status Discard Allow Overrun Enable” (TXSAO) bit in the TX Configuration Register
(TX_CFG). If this option is chosen TX status will not be written to the FIFO. Setting this bit high allows
the transmitter to continue operation with a full TX status FIFO. In this mode the status information is
still available in the TX status FIFO, and TX status interrupts still function. In the case of an overrun,
the TXSUSED counter will stay at zero and no further TX status will be written to the TX status FIFO
until the host frees space by reading TX status. If TXSAO is enabled, a TXE error will not be generated
if the TX status FIFO overruns. In this mode the host is responsible for re-synchronizing TX status in
the case of an overrun.
BITS
DESCRIPTION
31:16
Packet TAG. Unique identifier written by the host into the Packet Tag field of the TX command ‘B’
word. This field can be used by the host to correlate TX status words with the associated TX packets.
15
14:12
Error Status (ES). ). When set, this bit indicates that the Ethernet controller has reported an error.
This bit is the logical OR of bits 11, 10, 9, 8, 2, 1 in this status word.
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
11
Loss of Carrier. When set, this bit indicates the loss of carrier during transmission.
10
No Carrier. When set, this bit indicates that the carrier signal from the transceiver was not present
during transmission.
9
Late Collision. When set, indicates that the packet transmission was aborted after the collision
window of 64 bytes.
8
Excessive Collisions. When set, this bit indicates that the transmission was aborted after 16
collisions while attempting to transmit the current packet.
Revision 1.3 (05-31-07)
48
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
7
DESCRIPTION
Reserved. This bit is reserved. Always write zeros to this field to guarantee future compatibility.
6:3
Collision Count. This counter indicates the number of collisions that occurred before the packet was
transmitted. It is not valid when excessive collisions (bit 8) is also set.
2
Excessive Deferral. If the deferred bit is set in the control register, the setting of the excessive
deferral bit indicates that the transmission has ended because of a deferral of over 24288 bit times
during transmission.
1
Underrun Error. When set, this bit indicates that the transmitter aborted the associated frame
because of an underrun condition of the TX data FIFO. TX Underrun will cause the assertion of the
TXE error flag.
0
Deferred. When set, this bit indicates that the current packet transmission was deferred.
3.12.5
Calculating Actual TX Data FIFO Usage
The following rules are used to calculate the actual TX data FIFO space consumed by a TX Packet:
„
TX command 'A' is stored in the TX data FIFO for every TX buffer
„
TX command 'B' is written into the TX data FIFO when the First Segment (FS) bit is set in TX
command 'A'
„
Any DWORD-long data added as part of the “Data Start Offset” is removed from each buffer before
the data is written to the TX data FIFO. Any data that is less than 1 DWORD is passed to the TX
data FIFO.
„
Payload from each buffer within a Packet is written into the TX data FIFO.
„
Any DWORD-long data added as part of the End Padding is removed from each buffer before the
data is written to the TX data FIFO. Any end padding that is less than 1 DWORD is passed to the
TX data FIFO
3.12.6
Transmit Examples
3.12.6.1
TX Example 1
In this example a single, 111-Byte Ethernet packet will be transmitted. This packet is divided into three
buffers. The three buffers are as follows:
Buffer 0:
„
7-Byte “Data Start Offset”
„
79-Bytes of payload data
„
16-Byte “Buffer End Alignment”
Buffer 1:
„
0-Byte “Data Start Offset”
„
15-Bytes of payload data
„
16-Byte “Buffer End Alignment”
Buffer 2:
„
10-Byte “Data Start Offset”
„
17-Bytes of payload data
„
16-Byte “Buffer End Alignment”
Figure 3.14, "TX Example 1" illustrates the TX command structure for this example, and also shows
how data is passed to the TX data FIFO.
SMSC LAN9118
49
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Data W ritten to the
Ethernet Controller
31
TX Com m and 'A'
Buff er End Alignment = 1
Data Start Of fset = 7
First Segment = 1
Last Segment = 0
Buff er Size = 79
0
TX Command 'A'
Data Passed to the
TX Data FIFO
TX Command 'B'
7-Byte Data Start Offset
TX Command 'A'
TX Com m and 'B'
Packet Length = 111
TX Command 'B'
79-Byte Payload
79-Byte Payload
Pad DW ORD 1
10-Byte
End Padding
TX Command 'A'
31
TX Com m and 'A'
Buff er End Alignment = 1
Data Start Of fset = 0
First Segment = 0
Last Segment = 0
Buff er Size = 15
0
TX Command 'A'
15-Byte Payload
TX Command 'B'
TX Command 'A'
15-Byte Payload
TX Com m and 'B'
Packet Length = 111
1B
17-Byte Payload
31
TX Com m and 'A'
Buff er End Alignment = 1
Data Start Of fset = 10
First Segment = 0
Last Segment = 1
Buff er Size = 17
0
10-Byte
TXOffset
Command
'A'
End
Padding
TX Command 'B'
10-Byte
Data Start Offset
NOTE: Extra bytes
betw een buff ers are
not transmitted
TX Com m and 'B'
Packet Length = 111
17-Byte Payload Data
5-Byte End Padding
Figure 3.14 TX Example 1
Revision 1.3 (05-31-07)
50
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.12.6.2
TX Example 2
In this example, a single 183-Byte Ethernet packet will be transmitted. This packet is in a single buffer
as follows:
„
2-Byte “Data Start Offset”
„
183-Bytes of payload data
„
4-Byte “Buffer End Alignment”
Figure 3.15, "TX Example 2" illustrates the TX command structure for this example, and also shows
how data is passed to the TX data FIFO. Note that the packet resides in a single TX Buffer, therefore
both the FS and LS bits are set in TX command ‘A’.
Data Passed to the
TX Data FIFO
Data Written to the
Ethernet Controller
31
TX Command 'A'
Buffer End Alignment = 0
Data Start Offset = 6
First Segment = 1
Last Segment = 1
Buffer Size =183
0
TX Command 'A'
TX Command 'A'
TX Command 'B'
TX Command 'B'
6-Byte Data Start Offset
TX Command 'B'
Packet Length = 183
183-Byte Payload Data
183-Byte Payload Data
3B End Padding
NOTE: Extra bytes between buffers
are not transmitted
Figure 3.15 TX Example 2
SMSC LAN9118
51
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.12.7
TX Data FIFO Underrun
If the MIL is not operating in store and forward mode, and the host is unable supply data at the
Ethernet line rate, the TX data FIFO can underrun. If a TX underrun occurs, any further data written
to the TX data FIFO for the offending frame (the frame being transmitted during the underrun) will
automatically be discarded and no further data for that frame will be transmitted. TX data FIFO
underrun is not an error condition, and data transmission will resume with the next valid TX command.
In the case of a TX data FIFO underrun, the (TDFU) flag is set and can be used to generate a host
interrupt. A TX data FIFO underrun is also indicated in the TX status word for the underrun frame.
In the case of a TX underrun, the host is still required to write the remainder of the current TX packet
to the LAN9118. Any remaining data from the underrun frame that is written to the LAN9118 will backup in the TX data FIFO (no more data is read until the next TX SOF [start of frame]). As the data backs
up in the TX data FIFO, it will be visible in the TX_FIFO_INF register. In typical Driver usage, software
will write the entire transmit packet to the LAN9118 and check INT_STS and see (from TDFU) that the
underrun has occurred.
Eventually, the driver will recognize the underrun. A '1' must then be written to the TXD_DUMP bit in
the TX_CFG to flush the remaining data in the TX data FIFO (note that TX_ON may be kept on while
flushing the remaining TX data FIFO contents). Once the leftover data from the underrun frame is
purged, the LAN9118 is ready to send new transmit packets. It is advisable to clear the TDFU bit prior
to transmitting any more data (assuming that SF=0) so that subsequent underruns can be detected,
but this is not required by the hardware.
3.12.8
Transmitter Errors
If the Transmitter Error (TXE) flag is asserted for any reason, the transmitter will continue operation.
TX Error (TXE) will be asserted under the following conditions:
3.12.9
„
If the actual packet length count does not match the Packet Length field as defined in the TX
command.
„
Both TX command ‘A’ and TX command ‘B’ are required for each buffer in a given packet. TX
command ‘B’ must be identical for every buffer in a given packet. If the TX command ‘B’ words do
not match, the Ethernet controller will assert the Transmitter Error (TXE) flag.
„
Host overrun of the TX data FIFO.
„
Overrun of the TX status FIFO (unless TXSAO is enabled)
Stopping and Starting the Transmitter
To halt the transmitter, the host must set the TX_STOP bit in the TX_CFG register. The transmitter will
finish sending the current frame (if there is a frame transmission in progress). When the transmitter
has received the TX status for this frame, it will clear the TX_STOP and TX_ON bits, and will pulse
the TXSTOP_INT.
Once stopped, the host can optionally clear the TX status and TX data FIFOs. The host must re-enable
the transmitter by setting the TX_ON bit. If the there are frames pending in the TX data FIFO (i.e., TX
data FIFO was not purged), the transmission will resume with this data.
3.13
RX Data Path Operation
When an Ethernet Packet is received, the MIL first begins to transfer the RX data. This data is loaded
into the RX data FIFO. The RX data FIFO pointers are updated as data is written into the FIFO.
The last transfer from the MIL is the RX status word. The LAN9118 implements a separate FIFO for
the RX status words. The total available RX data and status queued in the RX FIFO can be read from
the RX_FIFO_INF register. The host may read any number of available RX status words before
reading the RX data FIFO.
Revision 1.3 (05-31-07)
52
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
The host must use caution when reading the RX data and status. The host must never read more data
than what is available in the FIFOs. If this is attempted an underrun condition will occur. If this error
occurs, the Ethernet controller will assert the Receiver Error (RXE) interrupt. If an underrun condition
occurs, a soft reset is required to regain host synchronization.
A configurable beginning offset is supported in the LAN9118. The RX data Offset field in the RX_CFG
register controls the number of bytes that the beginning of the RX data buffer is shifted. The host can
set an offset from 0-31 bytes. The offset may be changed in between RX packets, but it must not be
changed during an RX packet read.
The LAN9118 can be programmed to add padding at the end of a receive packet in the event that the
end of the packet does not align with the host burst boundary. This feature is necessary when the
LAN9118 is operating in a system that always performs multi-DWORD bursts. In such cases the
LAN9118 must guarantee that it can transfer data in multiples of the Burst length regardless of the
actual packet length. When configured to do so, the LAN9118 will add extra data at the end of the
packet to allow the host to perform the necessary number of reads so that the Burst length is not cut
short. Once a packet has been padded by the H/W, it is the responsibility of the host to interrogate the
Packet length field in the RX status and determine how much padding to discard at the end of the
Packet.
It is possible to read multiple packets out of the RX data FIFO in one continuous stream. It should be
noted that the programmed Offset and Padding will be added to each individual packet in the stream,
since packet boundaries are maintained.
3.13.1
RX Slave PIO Operation
Using PIO mode, the host can either implement a polling or interrupt scheme to empty the received
packet out of the RX data FIFO. The host will remain in the idle state until it receives an indication
(interrupt or polling) that data is available in the RX data FIFO. The host will then read the RX status
FIFO to get the packet status, which will contain the packet length and any other status information.
The host should perform the proper number of reads, as indicated by the packet length plus the start
offset and the amount of optional padding added to the end of the frame, from the RX data FIFO.
SMSC LAN9118
53
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
init
Idle
RX Interrupt
Read RX
Status
DWORD
Not Last Packet
Last Packet
Read RX
Packet
Figure 3.16 Host Receive Routine Using Interrupts
init
Read
RX_FIFO_
INf
Valid Status DWORD
Read RX
Status
DWORD
Not Last Packet
Last Packet
Read RX
Packet
Figure 3.17 Host Receive Routine with Polling
3.13.1.1
Receive Data FIFO Fast Forward
The RX data path implements an automatic data discard function. Using the RX data FIFO Fast
Forward bit (RX_FFWD) in the RX_DP_CTRL register, the host can instruct the LAN9118 to skip the
packet at the head of the RX data FIFO. The RX data FIFO pointers are automatically incremented to
the beginning of the next RX packet.
Revision 1.3 (05-31-07)
54
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
When performing a fast-forward, there must be at least 4 DWORDs of data in the RX data FIFO for
the packet being discarded. For less than 4 DWORDs do not use RX_FFWD. In this case data must
be read from the RX data FIFO and discarded using standard PIO read operations.
After initiating a fast-forward operation, do not perform any reads of the RX data FIFO until the
RX_FFWD bit is cleared. Other resources can be accessed during this time (i.e., any registers and/or
the other three FIFOs). Also note that the RX_FFWD will only fast-forward the RX data FIFO, not the
RX status FIFO.
The receiver does not have to be stopped to perform a fast-forward operation.
3.13.1.2
Force Receiver Discard (Receiver Dump)
In addition to the Receive data Fast Forward feature, LAN9118 also implements a receiver "dump"
feature. This feature allows the host processor to flush the entire contents of the RX data and RX
status FIFOs. When activated, the read and write pointers for the RX data and status FIFOs will be
returned to their reset state. To perform a receiver dump, the LAN9118 receiver must be halted. Once
the receiver stop completion is confirmed, the RX_DUMP bit can be set in the RX_CFG register. The
RX_DUMP bit is cleared when the dump is complete. For more information on stopping the receiver,
please refer to Section 3.13.4, "Stopping and Starting the Receiver," on page 56. For more information
on the RX_DUMP bit, please refer to Section 5.3.7, "RX_CFG—Receive Configuration Register," on
page 75.
3.13.2
RX Packet Format
The RX status words can be read from the RX status FIFO port, while the RX data packets can be
read from the RX data FIFO. RX data packets are formatted in a specific manner before the host can
read them. It is assumed that the host has previously read the associated status word from the RX
status FIFO, to ascertain the data size and any error conditions.
Host Read
Order
31
0
1st
Optional offset DWORD0
2nd
.
.
Optional offset DWORDn
ofs + First Data DWORD
.
.
.
.
Last Data DWORD
Optional Pad DWORD0
.
.
Last
Optional Pad DWORDn
Figure 3.18 RX Packet Format
SMSC LAN9118
55
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.13.3
RX Status Format
BITS
DESCRIPTION
31
Reserved. This bit is reserved. Reads 0.
30
Filtering Fail. When set, this bit indicates that the associated frame failed the address recognizing
filtering.
29:16
Packet Length. The size, in bytes, of the corresponding received frame.
15
Error Status (ES). When set this bit indicates that the MIL has reported an error. This bit is the
Internal logical “or” of bits 11,7,6 and 1.
14
Reserved. These bits are reserved. Reads 0.
13
Broadcast Frame. When set, this bit indicates that the received frame has a Broadcast address.
12
Length Error (LE). When set, this bit indicates that the actual length does not match with the
length/type field of the received frame.
11
Runt Frame. When set, this bit indicates that frame was prematurely terminated before the collision
window (64 bytes). Runt frames are passed on to the host only if the Pass Bad Frames bit MAC_CR
Bit [16] is set.
10
Multicast Frame. When set, this bit indicates that the received frame has a Multicast address.
9:8
Reserved. These bits are reserved. Reads 0.
7
Frame Too Long. When set, this bit indicates that the frame length exceeds the maximum Ethernet
specification of 1518 bytes. This is only a frame too long indication and will not cause the frame
reception to be truncated.
6
Collision Seen. When set, this bit indicates that the frame has seen a collision after the collision
window. This indicates that a late collision has occurred.
5
Frame Type. When set, this bit indicates that the frame is an Ethernet-type frame (Length/Type field
in the frame is greater than 1500). When reset, it indicates the incoming frame was an 802.3 type
frame. This bit is not set for Runt frames less than 14 bytes.
4
Receive Watchdog time-out. When set, this bit indicates that the incoming frame is greater than
2048 bytes through 2560 bytes, therefore expiring the Receive Watchdog Timer.
3
MII Error. When set, this bit indicates that a receive error (RX_ER asserted) was detected during
frame reception.
2
Dribbling Bit. When set, this bit indicates that the frame contained a non-integer multiple of 8 bits.
This error is reported only if the number of dribbling bits in the last byte is 4 in the MII operating mode,
or at least 3 in the 10 Mbps operating mode. This bit will not be set when the collision seen bit[6] is
set. If set and the CRC error bit is [1] reset, then the packet is considered to be valid.
1
CRC Error. When set, this bit indicates that a CRC error was detected. This bit is also set when the
RX_ER pin is asserted during the reception of a frame even though the CRC may be correct. This bit
is not valid if the received frame is a Runt frame, or a late collision was detected or when the
Watchdog Time-out occurs.
0
Reserved. These bits are reserved. Reads 0
3.13.4
Stopping and Starting the Receiver
To stop the receiver, the host must clear the RXEN bit in the MAC Control Register. When the receiver
is halted, the RXSTOP_INT will be pulsed. Once stopped, the host can optionally clear the RX status
and RX data FIFOs. The host must re-enable the receiver by setting the RXEN bit.
Revision 1.3 (05-31-07)
56
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.13.5
Receiver Errors
If the Receiver Error (RXE) flag is asserted for any reason, the receiver will continue operation. RX
Error (RXE) will be asserted under the following conditions:
„
A host underrun of RX data FIFO
„
A host underrun of the RX status FIFO
„
An overrun of the RX status FIFO
It is the duty of the host to identify and resolve any error conditions.
SMSC LAN9118
57
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Chapter 4 Internal Ethernet PHY
4.1
Top Level Functional Description
Functionally, the internal PHY can be divided into the following sections:
„
100Base-TX transmit and receive
„
10Base-T transmit and receive
„
Internal MII interface to the Ethernet Media Access Controller
„
Auto-negotiation to automatically determine the best speed and duplex possible
„
Management Control to read status registers and write control registers
100M
PLL
TX_CLK
MAC
Internal
MII 25 MHz by 4 bits
25MHz
by 4 bits
MII
4B/5B
Encoder
25MHz by
5 bits
MLT-3
Magnetics
Scrambler
and PISO
125 Mbps Serial
NRZI
Converter
NRZI
MLT-3
Converter
MLT-3
Tx
Driver
MLT-3
RJ45
MLT-3
CAT-5
Figure 4.1 100Base-TX Data Path
4.2
100Base-TX Transmit
The data path of the 100Base-TX is shown in Figure 4.1. Each major block is explained below.
4.2.1
4B/5B Encoding
The transmit data passes from the MII block to the 4B/5B encoder. This block encodes the data from
4-bit nibbles to 5-bit symbols (known as “code-groups”) according to Table 4.1. Each 4-bit data-nibble
is mapped to 16 of the 32 possible code-groups. The remaining 16 code-groups are either used for
control information or are not valid.
The first 16 code-groups are referred to by the hexadecimal values of their corresponding data nibbles,
0 through F. The remaining code-groups are given letter designations with slashes on either side. For
example, an IDLE code-group is /I/, a transmit error code-group is /H/, etc.
The encoding process may be bypassed by clearing bit 6 of register 31. When the encoding is
bypassed the 5th transmit data bit is equivalent to TX_ER.
Revision 1.3 (05-31-07)
58
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 4.1 4B/5B Code Table
CODE
GROUP
SYM
RECEIVER
INTERPRETATION
11110
0
0
0000
01001
1
1
10100
2
10101
TRANSMITTER
INTERPRETATION
0
0000
0001
1
0001
2
0010
2
0010
3
3
0011
3
0011
01010
4
4
0100
4
0100
01011
5
5
0101
5
0101
01110
6
6
0110
6
0110
01111
7
7
0111
7
0111
10010
8
8
1000
8
1000
10011
9
9
1001
9
1001
10110
A
A
1010
A
1010
10111
B
B
1011
B
1011
11010
C
C
1100
C
1100
11011
D
D
1101
D
1101
11100
E
E
1110
E
1110
11101
F
F
1111
F
1111
11111
I
IDLE
Sent after /T/R until TX_EN
11000
J
First nibble of SSD, translated to “0101”
following IDLE, else RX_ER
Sent for rising TX_EN
10001
K
Second nibble of SSD, translated to
“0101” following J, else RX_ER
Sent for rising TX_EN
01101
T
First nibble of ESD, causes de-assertion
of CRS if followed by /R/, else assertion
of RX_ER
Sent for falling TX_EN
00111
R
Second nibble of ESD, causes
deassertion of CRS if following /T/, else
assertion of RX_ER
Sent for falling TX_EN
00100
H
Transmit Error Symbol
Sent for rising TX_ER
00110
V
INVALID, RX_ER if during RX_DV
INVALID
11001
V
INVALID, RX_ER if during RX_DV
INVALID
00000
V
INVALID, RX_ER if during RX_DV
INVALID
00001
V
INVALID, RX_ER if during RX_DV
INVALID
00010
V
INVALID, RX_ER if during RX_DV
INVALID
00011
V
INVALID, RX_ER if during RX_DV
INVALID
00101
V
INVALID, RX_ER if during RX_DV
INVALID
SMSC LAN9118
DATA
59
DATASHEET
DATA
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 4.1 4B/5B Code Table (continued)
CODE
GROUP
SYM
01000
V
INVALID, RX_ER if during RX_DV
INVALID
01100
V
INVALID, RX_ER if during RX_DV
INVALID
10000
V
INVALID, RX_ER if during RX_DV
INVALID
4.2.2
RECEIVER
INTERPRETATION
TRANSMITTER
INTERPRETATION
Scrambling
Repeated data patterns (especially the IDLE code-group) can have power spectral densities with large
narrow-band peaks. Scrambling the data helps eliminate these peaks and spread the signal power
more uniformly over the entire channel bandwidth. This uniform spectral density is required by FCC
regulations to prevent excessive EMI from being radiated by the physical wiring.
The scrambler also performs the Parallel In Serial Out conversion (PISO) of the data.
4.2.3
NRZI and MLT3 Encoding
The scrambler block passes the 5-bit wide parallel data to the NRZI converter where it becomes a
serial 125MHz NRZI data stream. The NRZI is encoded to MLT-3. MLT3 is a tri-level code where a
change in the logic level represents a code bit “1” and the logic output remaining at the same level
represents a code bit “0”.
4.2.4
100M Transmit Driver
The MLT3 data is then passed to the analog transmitter, which launches the differential MLT-3 signal,
on outputs TXP and TXN, to the twisted pair media via a 1:1 ratio isolation transformer. The 10BaseT and 100Base-TX signals pass through the same transformer so that common “magnetics” can be
used for both. The transmitter drives into the 100Ω impedance of the CAT-5 cable. Cable termination
and impedance matching require external components.
4.2.5
100M Phase Lock Loop (PLL)
The 100M PLL locks onto reference clock and generates the 125MHz clock used to drive the 125 MHz
logic and the 100Base-Tx Transmitter.
Revision 1.3 (05-31-07)
60
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
100M
PLL
RX_CLK
MAC
Internal
MII 25MHz by 4 bits
25MHz
by 4 bits
MII
4B/5B
Decoder
25MHz by
5 bits
Descrambler
and SIPO
125 Mbps Serial
NRZI
Converter
A/D
Converter
NRZI
MLT-3
MLT-3
Converter
DSP: Timing
recovery, Equalizer
and BLW Correction
MLT-3
Magnetics
MLT-3
RJ45
MLT-3
CAT-5
6 bit Data
Figure 4.2 Receive Data Path
4.3
100Base-TX Receive
The receive data path is shown in Figure 4.2. Detailed descriptions are given below.
4.3.1
100M Receive Input
The MLT-3 from the cable is fed into the PHY (on inputs RXP and RXN) via a 1:1 ratio transformer.
The ADC samples the incoming differential signal at a rate of 125M samples per second. Using a 64level quanitizer it generates 6 digital bits to represent each sample. The DSP adjusts the gain of the
ADC according to the observed signal levels such that the full dynamic range of the ADC can be used.
4.3.2
Equalizer, Baseline Wander Correction and Clock and Data Recovery
The 6 bits from the ADC are fed into the DSP block. The equalizer in the DSP section compensates
for phase and amplitude distortion caused by the physical channel consisting of magnetics, connectors,
and CAT- 5 cable. The equalizer can restore the signal for any good-quality CAT-5 cable between 1m
and 150m.
If the DC content of the signal is such that the low-frequency components fall below the low frequency
pole of the isolation transformer, then the droop characteristics of the transformer will become
significant and Baseline Wander (BLW) on the received signal will result. To prevent corruption of the
received data, the PHY corrects for BLW and can receive the ANSI X3.263-1995 FDDI TP-PMD
defined “killer packet” with no bit errors.
The 100M PLL generates multiple phases of the 125MHz clock. A multiplexer, controlled by the timing
unit of the DSP, selects the optimum phase for sampling the data. This is used as the received
recovered clock. This clock is used to extract the serial data from the received signal.
4.3.3
NRZI and MLT-3 Decoding
The DSP generates the MLT-3 recovered levels that are fed to the MLT-3 converter. The MLT-3 is then
converted to an NRZI data stream.
SMSC LAN9118
61
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
4.3.4
Descrambling
The descrambler performs an inverse function to the scrambler in the transmitter and also performs
the Serial In Parallel Out (SIPO) conversion of the data.
During reception of IDLE (/I/) symbols. the descrambler synchronizes its descrambler key to the
incoming stream. Once synchronization is achieved, the descrambler locks on this key and is able to
descramble incoming data.
Special logic in the descrambler ensures synchronization with the remote PHY by searching for IDLE
symbols within a window of 4000 bytes (40us). This window ensures that a maximum packet size of
1514 bytes, allowed by the IEEE 802.3 standard, can be received with no interference. If no IDLEsymbols are detected within this time-period, receive operation is aborted and the descrambler re-starts
the synchronization process.
The descrambler can be bypassed by setting bit 0 of register 31.
4.3.5
Alignment
The de-scrambled signal is then aligned into 5-bit code-groups by recognizing the /J/K/ Start-of-Stream
Delimiter (SSD) pair at the start of a packet. Once the code-word alignment is determined, it is stored
and utilized until the next start of frame.
4.3.6
5B/4B Decoding
The 5-bit code-groups are translated into 4-bit data nibbles according to the 4B/5B table. The SSD,
/J/K/, is translated to “0101 0101” as the first 2 nibbles of the MAC preamble. Reception of the SSD
causes the PHY to assert the internal RX_DV signal, indicating that valid data is available on the
Internal RXD bus. Successive valid code-groups are translated to data nibbles. Reception of either the
End of Stream Delimiter (ESD) consisting of the /T/R/ symbols, or at least two /I/ symbols causes the
PHY to de-assert the internal carrier sense and RX_DV.
These symbols are not translated into data.
4.4
10Base-T Transmit
Data to be transmitted comes from the MAC layer controller. The 10Base-T transmitter receives 4-bit
nibbles from the MII at a rate of 2.5MHz and converts them to a 10Mbps serial data stream. The data
stream is then Manchester-encoded and sent to the analog transmitter, which drives a signal onto the
twisted pair via the external magnetics.
The 10M transmitter uses the following blocks:
4.4.1
„
MII (digital)
„
TX 10M (digital)
„
10M Transmitter (analog)
„
10M PLL (analog)
10M Transmit Data across the internal MII bus
The MAC controller drives the transmit data onto the internal TXD BUS. When the controller has driven
TX_EN high to indicate valid data, the data is latched by the MII block on the rising edge of TX_CLK.
The data is in the form of 4-bit wide 2.5MHz data.
4.4.2
Manchester Encoding
The 4-bit wide data is sent to the TX10M block. The nibbles are converted to a 10Mbps serial NRZI
data stream. The 10M PLL locks onto the external clock or internal oscillator and produces a 20MHz
clock. This is used to Manchester encode the NRZ data stream. When no data is being transmitted
Revision 1.3 (05-31-07)
62
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
(TX_EN is low), the TX10M block outputs Normal Link Pulses (NLPs) to maintain communications with
the remote link partner.
4.4.3
10M Transmit Drivers
The Manchester encoded data is sent to the analog transmitter where it is shaped and filtered before
being driven out as a differential signal across the TXP and TXN outputs.
4.5
10Base-T Receive
The 10Base-T receiver gets the Manchester- encoded analog signal from the cable via the magnetics.
It recovers the receive clock from the signal and uses this clock to recover the NRZI data stream. This
10M serial data is converted to 4-bit data nibbles which are passed to the controller across the MII at
a rate of 2.5MHz.
This 10M receiver uses the following blocks:
4.5.1
„
Filter and SQUELCH (analog)
„
10M PLL (analog)
„
RX 10M (digital)
„
MII (digital)
10M Receive Input and Squelch
The Manchester signal from the cable is fed into the PHY (on inputs RXP and RXN) via 1:1 ratio
magnetics. It is first filtered to reduce any out-of-band noise. It then passes through a SQUELCH
circuit. The SQUELCH is a set of amplitude and timing comparators that normally reject differential
voltage levels below 300mV and detect and recognize differential voltages above 585mV.
4.5.2
Manchester Decoding
The output of the SQUELCH goes to the RX10M block where it is validated as Manchester encoded
data. The polarity of the signal is also checked. If the polarity is reversed (local RXP is connected to
RXN of the remote partner and vice versa), then this is identified and corrected. The reversed condition
is indicated by the flag “XPOL“, bit 4 in register 27. The 10M PLL is locked onto the received
Manchester signal and from this, generates the received 20MHz clock. Using this clock, the
Manchester encoded data is extracted and converted to a 10MHz NRZI data stream. It is then
converted from serial to 4-bit wide parallel data.
The RX10M block also detects valid 10Base-T IDLE signals - Normal Link Pulses (NLPs) - to maintain
the link.
4.5.3
Jabber Detection
Jabber is a condition in which a station transmits for a period of time longer than the maximum
permissible packet length, usually due to a fault condition, that results in holding the TX_EN input for
a long period. Special logic is used to detect the jabber state and abort the transmission to the line,
within 45ms. Once TX_EN is deasserted, the logic resets the jabber condition.
4.6
Auto-negotiation
The purpose of the Auto-negotiation function is to automatically configure the PHY to the optimum link
parameters based on the capabilities of its link partner. Auto-negotiation is a mechanism for
exchanging configuration information between two link-partners and automatically selecting the highest
performance mode of operation supported by both sides. Auto-negotiation is fully defined in clause 28
of the IEEE 802.3 specification.
SMSC LAN9118
63
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Once auto-negotiation has completed, information about the resolved link can be passed back to the
controller via the internal Serial Management Interface (SMI). The results of the negotiation process
are reflected in the Speed Indication bits in register 31, as well as the Link Partner Ability Register
(Register 5).
The auto-negotiation protocol is a purely physical layer activity and proceeds independently of the MAC
controller.
The advertised capabilities of the PHY are stored in register 4 of the SMI registers. The default
advertised by the PHY is determined by user-defined on-chip signal options.
The following blocks are activated during an Auto-negotiation session:
„
Auto-negotiation (digital)
„
100M ADC (analog)
„
100M PLL (analog)
„
100M equalizer/BLW/clock recovery (DSP)
„
10M SQUELCH (analog)
„
10M PLL (analog)
„
10M Transmitter (analog)
When enabled, auto-negotiation is started by the occurrence of one of the following events:
„
Hardware reset
„
Software reset
„
Power-down reset
„
Link status down
„
Setting register 0, bit 9 high (auto-negotiation restart)
On detection of one of these events, the PHY begins auto-negotiation by transmitting bursts of Fast
Link Pulses (FLP). These are bursts of link pulses from the 10M transmitter. They are shaped as
Normal Link Pulses and can pass uncorrupted down CAT-3 or CAT-5 cable. A Fast Link Pulse Burst
consists of up to 33 pulses. The 17 odd-numbered pulses, which are always present, frame the FLP
burst. The 16 even-numbered pulses, which may be present or absent, contain the data word being
transmitted. Presence of a data pulse represents a “1”, while absence represents a “0”.
The data transmitted by an FLP burst is known as a “Link Code Word.” These are defined fully in IEEE
802.3 clause 28. In summary, the PHY advertises 802.3 compliance in its selector field (the first 5 bits
of the Link Code Word). It advertises its technology ability according to the bits set in register 4 of the
SMI registers.
There are 4 possible matches of the technology abilities. In the order of priority these are:
„
100M full-duplex (Highest priority)
„
100M half-duplex
„
10M full-duplex
„
10M half-duplex
If the full capabilities of the PHY are advertised (100M, full-duplex), and if the link partner is capable
of 10M and 100M, then auto-negotiation selects 100M as the highest performance mode. If the link
partner is capable of half and full-duplex modes, then auto-negotiation selects full-duplex as the highest
performance operation.
Once a capability match has been determined, the link code words are repeated with the acknowledge
bit set. Any difference in the main content of the link code words at this time will cause auto-negotiation
to re-start. Auto-negotiation will also re-start if not all of the required FLP bursts are received.
Writing register 4 bits [8:5] allows software control of the capabilities advertised by the PHY. Writing
register 4 does not automatically re-start auto-negotiation. Register 0, bit 9 must be set before the new
Revision 1.3 (05-31-07)
64
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
abilities will be advertised. Auto-negotiation can also be disabled via software by clearing register 0,
bit 12.
The LAN9118 does not support “Next Page" capability.
4.7
Parallel Detection
If the LAN9118 is connected to a device lacking the ability to auto-negotiate (i.e. no FLPs are
detected), it is able to determine the speed of the link based on either 100M MLT-3 symbols or 10M
Normal Link Pulses. In this case the link is presumed to be half-duplex per the IEEE standard. This
ability is known as “Parallel Detection. This feature ensures inter operability with legacy link partners.
If a link is formed via parallel detection, then bit 0 in register 6 is cleared to indicate that the Link
Partner is not capable of auto-negotiation. The Ethernet MAC has access to this information via the
management interface. If a fault occurs during parallel detection, bit 4 of register 6 is set.
Register 5 is used to store the Link Partner Ability information, which is coded in the received FLPs.
If the Link Partner is not auto-negotiation capable, then register 5 is updated after completion of parallel
detection to reflect the speed capability of the Link Partner.
4.7.1
Re-starting Auto-negotiation
Auto-negotiation can be re-started at any time by setting register 0, bit 9. Auto-negotiation will also restart if the link is broken at any time. A broken link is caused by signal loss. This may occur because
of a cable break, or because of an interruption in the signal transmitted by the Link Partner. Autonegotiation resumes in an attempt to determine the new link configuration.
If the management entity re-starts Auto-negotiation by writing to bit 9 of the control register, the
LAN9118 will respond by stopping all transmission/receiving operations. Once the break_link_timer is
done, in the Auto-negotiation state-machine (approximately 1200ms) the auto-negotiation will re-start.
The Link Partner will have also dropped the link due to lack of a received signal, so it too will resume
auto-negotiation.
4.7.2
Disabling Auto-negotiation
Auto-negotiation can be disabled by setting register 0, bit 12 to zero. The device will then force its
speed of operation to reflect the information in register 0, bit 13 (speed) and register 0, bit 8 (duplex).
The speed and duplex bits in register 0 should be ignored when auto-negotiation is enabled.
4.7.3
Half vs. Full-Duplex
Half-duplex operation relies on the CSMA/CD (Carrier Sense Multiple Access / Collision Detect)
protocol to handle network traffic and collisions. In this mode, the carrier sense signal, CRS, responds
to both transmit and receive activity. In this mode, If data is received while the PHY is transmitting, a
collision results.
In full-duplex mode, the PHY is able to transmit and receive data simultaneously. In this mode, CRS
responds only to receive activity. The CSMA/CD protocol does not apply and collision detection is
disabled. Table 4.2 describes the behavior of the CRS bit under all receive/transmit conditions.
SMSC LAN9118
65
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 4.2 CRS Behavior
MODE
SPEED
DUPLEX
ACTIVITY
CRS BEHAVIOR
(Note 4.1)
Manual
10 Mbps
Half-Duplex
Transmitting
Active
Manual
10 Mbps
Half-Duplex
Receiving
Active
Manual
10 Mbps
Full-Duplex
Transmitting
Low
Manual
10 Mbps
Full-Duplex
Receiving
Active
Manual
100 Mbps
Half-Duplex
Transmitting
Active
Manual
100 Mbps
Half-Duplex
Receiving
Active
Manual
100 Mbps
Full-Duplex
Transmitting
Low
Manual
100 Mbps
Full-Duplex
Receiving
Active
Auto-Negotiation
10 Mbps
Half-Duplex
Transmitting
Active
Auto-Negotiation
10 Mbps
Half-Duplex
Receiving
Active
Auto-Negotiation
10 Mbps
Full-Duplex
Transmitting
Low
Auto-Negotiation
10 Mbps
Full-Duplex
Receiving
Active
Auto-Negotiation
100 Mbps
Half-Duplex
Transmitting
Active
Auto-Negotiation
100 Mbps
Half-Duplex
Receiving
Active
Auto-Negotiation
100 Mbps
Full-Duplex
Transmitting
Low
Auto-Negotiation
100 Mbps
Full-Duplex
Receiving
Active
Note 4.1
Revision 1.3 (05-31-07)
The LAN9118 10/100 PHY CRS signal operates in two modes: Active and Low. When in
Active mode, CRS will transition high and low upon line activity, where a high value
indicates a carrier has been detected. In Low mode, CRS stays low and does not indicate
carrier detection. The CRS signal cannot be used as a verification method of transmitted
packets when transmitting in 10 or 100 Mbps in full-duplex mode.
66
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Chapter 5 Register Description
The following section describes all LAN9118 registers and data ports.
FCh
RESERVED
B4h
EEPROM Port
B0h
ACh
A8h
A4h
A0h
50h
4Ch
48h
44h
40h
3Ch
MAC CSRPort
TX Status
TX Status
RX Status
RX Status
FIFO PEEK
FIFO Port
FIFO PEEK
FIFO Port
TX Data FIFO Alias Ports
24h
20h
1Ch
TX Data FIFO Port
RX Data FIFO Alias Ports
04h
Base + 00h
RX Data FIFO Port
Figure 5.1 LAN9118 Memory Map
SMSC LAN9118
67
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.1
Register Nomenclature and Access Attributes
SYMBOL
DESCRIPTION
RO
Read Only: If a register is read only, writes to this register have no effect.
WO
Write Only: If a register is write only, reads always return 0.
R/W
Read/Write: A register with this attribute can be read and written
R/WC
Read/Write Clear: A register bit with this attribute can be read and written. However, a write
of a 1 clears (sets to 0) the corresponding bit and a write of a 0 has no effect.
RC
Read to Clear: A register bit with this attribute is cleared when read.
LL
Latch Low: Clear on read of register
LH
Latch High: Clear on read of register
SC
Self-Clearing
NASR
Not Affected by Software Reset
Reserved
Bits
Unless otherwise stated, reserved fields must be written with zeros to ensure future
compatibility. The value of reserved bits is not guaranteed on a read.
Reserved
Registers
In addition to reserved bits within a register, the LAN9118 contains address locations in the
configuration space that are marked “Reserved. When a “Reserved” register location is read,
a random value can be returned. Registers that are marked as “Reserved” must not be
modified by system software. Writes to “Reserved” registers may cause system failure.
Default
Value Upon
Reset
Upon a Reset (System reset, Software Reset, or POR), the LAN9118 sets its internal
configuration registers to predetermined default states. The default state represents the
minimum functionality feature set required to successfully bring up the system. Hence, it does
not represent the optimal system configuration. It is the responsibility of the system
initialization software to properly determine the operating parameters and optional system
features that are applicable, and to program the LAN9118 registers accordingly.
5.2
RX and TX FIFO Ports
The LAN9118 contains four host-accessible FIFOs: the RX Status, RX data, TX Status, and TX data
FIFOs. The sizes of the RX and TX data FIFOs, as well as the RX Status FIFO are configurable
through the CSRs.
5.2.1
RX FIFO Ports
The RX data Path consists of two Read-Only FIFOs; the RX Status and data. The RX Status FIFO can
be read from two locations. The RX Status FIFO Port will perform a destructive read, thus “Popping”
the data from the RX Status FIFO. There is also the RX Status FIFO PEEK location. This location
allows a non-destructive read of the top (oldest) location of the FIFO.
The RX data FIFO only allows destructive reads. It is aliased in 8 DWORD locations (16 WORD
locations in 16-bit mode) from the 00h offset to 1Ch offset. The host may access any of the 8(16)
locations since they all contain the same data and perform the same function.
Revision 1.3 (05-31-07)
68
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.2.2
TX FIFO Ports
The TX data Path consists of two FIFOs, the TX status and data. The TX Status FIFO can be read
from two locations. The TX Status FIFO Port will perform a destructive read, thus “Popping” the data
from the TX Status FIFO. There is also the TX Status FIFO PEEK location. This location allows a nondestructive read of the top (oldest) location of the FIFO.
The TX data FIFO is Write Only. It is aliased in 8 DWORD locations (16 WORD locations in 16-bit
mode) from the 20h offset to 3Ch offset. The host may write to any of the 8(16) locations since they
all access the same TX data FIFO location and perform the same function.
5.3
System Control and Status Registers
Table 5.1, "LAN9118 Direct Address Register Map", lists the registers that are directly addressable by
the host bus.
Table 5.1 LAN9118 Direct Address Register Map
CONTROL AND STATUS REGISTERS
BASE ADDRESS
+ OFFSET
SYMBOL
50h
ID_REV
54h
IRQ_CFG
Main Interrupt Configuration
00000000h
58h
INT_STS
Interrupt Status
00000000h
5Ch
INT_EN
Interrupt Enable Register
00000000h
60h
RESERVED
Reserved for future use
-
64h
BYTE_TEST
Read-only byte order testing register
87654321h
68h
FIFO_INT
FIFO Level Interrupts
48000000h
6Ch
RX_CFG
Receive Configuration
00000000h
70h
TX_CFG
Transmit Configuration
00000000h
74h
HW_CFG
Hardware Configuration
00050000h
78h
RX_DP_CTL
RX Datapath Control
00000000h
7Ch
RX_FIFO_INF
Receive FIFO Information
00000000h
80h
TX_FIFO_INF
Transmit FIFO Information
00001200h
84h
PMT_CTRL
Power Management Control
00000000h
88h
GPIO_CFG
General Purpose IO Configuration
00000000h
8Ch
GPT_CFG
General Purpose Timer Configuration
0000FFFFh
90h
GPT_CNT
General Purpose Timer Count
0000FFFFh
94h
RESERVED
Reserved for future use
-
98h
WORD_SWAP
WORD SWAP Register
00000000h
SMSC LAN9118
REGISTER NAME
Chip ID and Revision.
69
DATASHEET
DEFAULT
See “ID_REV—
Chip ID and
Revision” on
page 70.
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 5.1 LAN9118 Direct Address Register Map (continued)
CONTROL AND STATUS REGISTERS
BASE ADDRESS
+ OFFSET
SYMBOL
9Ch
FREE_RUN
Free Run Counter
A0h
RX_DROP
RX Dropped Frames Counter
00000000h
A4h
MAC_CSR_CMD
MAC CSR Synchronizer Command (MAC
CSR’s are indexed through this register)
00000000h
A8h
MAC_CSR_DATA
MAC CSR Synchronizer Data
00000000h
ACh
AFC_CFG
Automatic Flow Control Configuration
00000000h
B0h
E2P_CMD
EEPROM command (The EEPROM is
indexed through this register)
00000000h
B4h
E2P_DATA
EEPROM Data
00000000h
B8h - FCh
RESERVED
Reserved for future use
5.3.1
REGISTER NAME
DEFAULT
-
-
ID_REV—Chip ID and Revision
Offset:
50h
Size:
32 bits
This register contains the ID and Revision fields for this design.
BITS
DESCRIPTION
TYPE
DEFAULT
31-16
Chip ID. This read-only field identifies this design
RO
0118h
15-0
Chip Revision. This is the current revision of the chip.
RO
0001h
Revision 1.3 (05-31-07)
70
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.2
IRQ_CFG—Interrupt Configuration Register
Offset:
54h
Size:
32 bits
This register configures and indicates the state of the IRQ signal.
BITS
31:24
DESCRIPTION
TYPE
Interrupt Deassertion Interval (INT_DEAS). This field determines the
Interrupt Deassertion Interval for the Interrupt Request in multiples of 10
microseconds.
DEFAULT
R/W
0
Reserved
RO
-
14
Interrupt Deassertion Interval Clear (INT_DEAS_CLR). Writing a one
to this register clears the de-assertion counter in the IRQ Controller, thus
causing a new de-assertion interval to begin (regardless of whether or
not the IRQ Controller is currently in an active de-assertion interval).
SC
0
13
Interrupt Deassertion Status (INT_DEAS_STS). When set, this bit
indicates that the INT_DEAS is currently in a deassertion interval, and
any interrupts (as indicated by the IRQ_INT and INT_EN bits) will not be
delivered to the IRQ pin. When cleared, the INT_DEAS is currently not
in a deassertion interval, and enabled interrupts will be delivered to the
IRQ pin.
SC
0
12
Master Interrupt (IRQ_INT). This read-only bit indicates the state of the
internal IRQ line. When set high, one of the enabled interrupts is
currently active. This bit will respond to the associated interrupts
regardless of the IRQ_EN field. This bit is not affected by the setting of
the INT_DEAS field.
RO
0
Reserved
RO
-
IRQ Enable (IRQ_EN) – This bit controls the final interrupt output to the
IRQ pin. When cleared, the IRQ output is disabled and will be
permanently deasserted. This bit only controls the external IRQ signal,
and has no effect on any of the internal interrupt status bits.
R/W
0
Reserved
RO
-
R/W
NASR
0
RO
-
R/W
NASR
0
Writing zeros to this field disables the INT_DEAS Interval and resets the
interval counter. Any pending interrupts are then issued. If a new, nonzero value is written to the INT_DEAS field, any subsequent interrupts
will obey the new setting.
Note:
23-15
11-9
8
7-5
4
3-1
0
The Interrupt Deassertion interval does not apply to the PME
interrupt.
IRQ Polarity (IRQ_POL) – When cleared, enables the IRQ line to
function as an active low output. When set, the IRQ output is active high.
When IRQ is configured as an open-drain output this field is ignored,
and the interrupt output is always active low.
Reserved
IRQ Buffer Type (IRQ_TYPE) – When cleared, enables IRQ to function
as an open-drain buffer for use in a Wired-Or Interrupt configuration.
When set, the IRQ output is a Push-Pull driver. When configured as an
open-drain output the IRQ_POL field is ignored, and the interrupt output
is always active low.
SMSC LAN9118
71
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.3
INT_STS—Interrupt Status Register
Offset:
58h
Size:
32 bits
This register contains the current status of the generated interrupts. Writing a 1 to the corresponding
bits acknowledges and clears the interrupt.
BITS
31
30-26
DESCRIPTION
Software Interrupt (SW_INT). This interrupt is generated when the
SW_INT_EN bit is set high. Writing a one clears this interrupt.
Reserved
TYPE
DEFAULT
R/WC
0
RO
-
25
TX Stopped (TXSTOP_INT). This interrupt is issued when STOP_TX bit
in TX_CFG is set, and the transmitter is halted.
R/WC
0
24
RX Stopped (RXSTOP_INT). This interrupt is issued when the receiver is
halted.
R/WC
0
23
RX Dropped Frame Counter Halfway (RXDFH_INT). This interrupt is
issued when the RX Dropped Frames Counter counts past its halfway
point (7FFFFFFFh to 80000000h).
R/WC
0
22
Reserved
RO
0
21
TX IOC Interrupt (TX_IOC). When a buffer with the IOC flag set has
finished being loaded into the TX FIFO, this interrupt is generated.
R/WC
0
20
RX DMA Interrupt (RXD_INT). This interrupt is issued when the amount
of data programmed in the RX DMA Count (RX_DMA_CNT) field of the
RX_CFG register has been transferred out of the RX FIFO.
R/WC
0
19
GP Timer (GPT_INT). This interrupt is issued when the General Purpose
timer wraps past zero to FFFFh.
R/WC
0
18
PHY (PHY_INT). Indicates a PHY Interrupt event.
RO
0
17
Power Management Event Interrupt (PME_INT). This interrupt is issued
when a Power Management Event is detected as configured in the
PMT_CTRL register. This interrupt functions independent of the PME
signal, and will still function if the PME signal is disabled. Writing a '1'
clears this bit regardless of the state of the PME hardware signal.
Notes:
„ Detection of a Power Management Event, and assertion of the PME
signal will not wakeup the LAN9118. The LAN9118 will only wake up
when it detects a host write cycle of any data to the BYTE_TEST
register.
„ The Interrupt Deassertion interval does not apply to the PME interrupt.
R/WC
0
TX Status FIFO Overflow (TXSO). Generated when the TX Status
R/WC
0
R/WC
0
R/WC
0
R/WC
0
16
FIFO overflows.
15
Receive Watchdog Time-out (RWT). Interrupt is generated when a
packet larger than 2048 bytes has been received.
14
Receiver Error (RXE). Indicates that the receiver has encountered an
error. Please refer to Section 3.13.5, "Receiver Errors," on page 57 for a
description of the conditions that will cause an RXE.
13
Transmitter Error (TXE). When generated, indicates that the
transmitter has encountered an error. Please refer to Section 3.12.8,
"Transmitter Errors," on page 52, for a description of the conditions that
will cause a TXE.
Revision 1.3 (05-31-07)
72
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
RO
-
12
Reserved
11
TX Data FIFO Underrun Interrupt (TDFU). Generated when the TX data
FIFO underruns.
R/WC
0
10
TX Data FIFO Overrun Interrupt (TDFO). Generated when the TX data
FIFO is full, and another write is attempted.
R/WC
0
9
TX Data FIFO Available Interrupt (TDFA). Generated when the TX data
FIFO available space is greater than the programmed level.
R/WC
0
8
TX Status FIFO Full Interrupt (TSFF). Generated when the TX Status
FIFO is full.
R/WC
0
7
TX Status FIFO Level Interrupt (TSFL). Generated when the TX Status
FIFO reaches the programmed level.
R/WC
0
6
RX Dropped Frame Interrupt (RXDF_INT). This interrupt is issued
whenever a receive frame is dropped.
R/WC
0
5
RX Data FIFO Level Interrupt (RDFL). Generated when the RX FIFO
reaches the programmed level.
R/WC
0
4
RX Status FIFO Full Interrupt (RSFF). Generated when the RX Status
FIFO is full.
R/WC
0
3
RX Status FIFO Level Interrupt (RSFL). Generated when the RX Status
FIFO reaches the programmed level.
R/WC
0
GPIO [2:0] (GPIOx_INT). Interrupts are generated from the GPIO’s.
These interrupts are configured through the GPIO_CFG register.
R/WC
000
2-0
5.3.4
INT_EN—Interrupt Enable Register
Offset:
5Ch
Size:
32 bits
This register contains the interrupt masks for IRQ. Writing 1 to any of the bits enables the
corresponding interrupt as a source for IRQ. Bits in the INT_STS register will still reflect the status of
the interrupt source regardless of whether the source is enabled as an interrupt in this register.
BITS
31
DESCRIPTION
TYPE
DEFAULT
Software Interrupt (SW_INT_EN)
R/W
0
Reserved
RO
-
25
TX Stopped Interrupt Enable (TXSTOP_INT_EN)
R/W
0
24
RX Stopped Interrupt Enable (RXSTOP_INT_EN)
R/W
0
23
RX Dropped Frame Counter Halfway Interrupt Enable
(RXDFH_INT_EN).
R/W
0
22
Reserved
RO
0
21
TX IOC Interrupt Enable (TIOC_INT_EN)
R/W
0
20
RX DMA Interrupt (RXD_INT).
R/W
0
19
GP Timer (GPT_INT_EN)
R/W
0
30:26
SMSC LAN9118
73
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
18
PHY (PHY_INT_EN)
R/W
0
17
Power Management Event Interrupt Enable (PME_INT_EN)
R/W
0
16
TX Status FIFO Overflow (TXSO_EN)
R/W
0
15
Receive Watchdog Time-out Interrupt (RWT_INT_EN)
R/W
0
14
Receiver Error Interrupt (RXE_INT_EN)
R/W
0
13
Transmitter Error Interrupt (TXE_INT_EN)
R/W
0
12
Reserved
RO
-
11
TX Data FIFO Underrun Interrupt (TDFU_INT_EN)
R/W
0
10
TX Data FIFO Overrun Interrupt (TDFO_INT_EN)
R/W
0
9
TX Data FIFO Available Interrupt (TDFA_INT_EN)
R/W
0
8
TX Status FIFO Full Interrupt (TSFF_INT_EN)
R/W
0
7
TX Status FIFO Level Interrupt (TSFL_INT_EN)
R/W
0
6
RX Dropped Frame Interrupt Enable (RXDF_INT_EN)
R/W
0
5
RX Data FIFO Level Interrupt (RDFL_INT_EN)
R/W
0
4
RX Status FIFO Full Interrupt (RSFF_INT_EN)
R/W
0
3
RX Status FIFO Level Interrupt (RSFL_INT_EN)
R/W
0
GPIO [2:0] (GPIOx_INT_EN).
R/W
000
2-0
5.3.5
BYTE_TEST—Byte Order Test Register
Offset:
64h
Size:
32 bits
This register can be used to determine the byte ordering of the current configuration
BITS
DESCRIPTION
31:0
Byte Test
Revision 1.3 (05-31-07)
74
DATASHEET
TYPE
DEFAULT
RO
87654321h
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.6
FIFO_INT—FIFO Level Interrupts
Offset:
68h
Size:
32 bits
This register configures the limits where the FIFO Controllers will generate system interrupts.
BITS
DESCRIPTION
TYPE
DEFAULT
31-24
TX Data Available Level. The value in this field sets the level, in number
of 64 Byte blocks, at which the TX FIFO Available interrupt (TFDA) will be
generated. When the TX data FIFO free space is greater than this value a
TX FIFO Available interrupt (TDFA) will be generated.
R/W
48h
23-16
TX Status Level. The value in this field sets the level, in number of
DWORDs, at which the TX Status FIFO Level interrupt (TSFL) will be
generated. When the TX Status FIFO used space is greater than this value
an TX Status FIFO Level interrupt (TSFL) will be generated.
R/W
00h
15-8
RX Space Available Level. The value in this field sets the level, in number
of 64 Byte blocks, at which the RX data FIFO Level interrupt (RDFL) will be
generated. When the RX data FIFO free space is less than this value an RX
data FIFO Level interrupt (RDFL) will be generated.
R/W
00h
7-0
RX Status Level. The value in this field sets the level, in number of
DWORDs, at which the RX Status FIFO Level interrupt (RSFL) will be
generated. When the RX Status FIFO used space is greater than this value
an RX Status FIFO Level interrupt (RSFL) will be generated.
R/W
00h
5.3.7
RX_CFG—Receive Configuration Register
Offset:
6Ch
Size:
32 bits
This register controls the LAN9118 receive engine.
BITS
DESCRIPTION
TYPE
DEFAULT
31:30
RX End Alignment. This field specifies the alignment that must be
maintained on the last data transfer of a buffer. The LAN9118 will add
extra DWORDs of data up to the alignment specified in the table below.
The host is responsible for removing these extra DWORDs. This
mechanism can be used to maintain cache line alignment on host
processors.
Please refer to Table 5.2 for bit definitions
R/W
00b
Note:
The desired RX End Alignment must be set before reading a
packet. The RX end alignment can be changed between reading
receive packets, but must not be changed if the packet is
partially read.
29-28
Reserved
RO
-
27-16
RX DMA Count (RX_DMA_CNT). This 12-bit field indicates the amount
of data, in DWORDS, to be transferred out of the RX data FIFO before
asserting the RXD_INT. After being set, this field is decremented for each
DWORD of data that is read from the RX data FIFO. This field can be
overwritten with a new value before it reaches zero.
R/W
000h
SMSC LAN9118
75
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
15
Force RX Discard (RX_DUMP). This self-clearing bit clears the RX data
and status FIFOs of all pending data. When a ‘1’ is written, the RX data
and status pointers are cleared to zero.
SC
0
Note:
Please refer to section “Force Receiver Discard (Receiver
Dump)” on page 55 for a detailed description regarding the use
of RX_DUMP.
14-13
Reserved
RO
-
12-8
RX Data Offset (RXDOFF). This field controls the offset value, in bytes,
that is added to the beginning of an RX data packet. The start of the valid
data will be shifted by the number of bytes specified in this field. An offset
of 0-31 bytes is a valid number of offset bytes.
R/W
00000
RO
-
Note:
7-0
The two LSBs of this field (D[9:8]) must not be modified while
the RX is running. The receiver must be halted, and all data
purged before these two bits can be modified. The upper three
bits (DWORD offset) may be modified while the receiver is
running. Modifications to the upper bits will take affect on the
next DWORD read.
Reserved
Table 5.2 RX Alignment Bit Definitions
[31]
[30]
End Alignment
0
0
4-byte alignment
0
1
16-byte alignment
1
0
32-byte alignment
1
1
Reserved
5.3.8
TX_CFG—Transmit Configuration Register
Offset:
70h
Size:
32 bits
This register controls the transmit functions on the LAN9118 Ethernet Controller.
BITS
DESCRIPTION
TYPE
DEFAULT
31-16
Reserved.
RO
-
15
Force TX Status Discard (TXS_DUMP). This self-clearing bit clears the TX
status FIFO of all pending status DWORD’s. When a ‘1’ is written, the TX
status pointers are cleared to zero.
SC
0
14
Force TX Data Discard (TXD_DUMP). This self-clearing bit clears the TX
data FIFO of all pending data. When a ‘1’ is written, the TX data pointers
are cleared to zero.
SC
0
Reserved
RO
-
13-3
Revision 1.3 (05-31-07)
76
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
2
DESCRIPTION
TYPE
DEFAULT
TX Status Allow Overrun (TXSAO). When this bit is cleared, data
transmission is suspended if the TX Status FIFO becomes full. Setting this
bit high allows the transmitter to continue operation with a full TX Status
FIFO.
R/W
0
Note:
This bit does not affect the operation of the TX Status FIFO Full
interrupt.
1
Transmitter Enable (TX_ON). When this bit is set (1), the transmitter is
enabled. Any data in the TX FIFO will be sent. This bit is cleared
automatically when STOP_TX is set and the transmitter is halted.
R/W
0
0
Stop Transmitter (STOP_TX). When this bit is set (1), the transmitter will
finish the current frame, and will then stop transmitting. When the transmitter
has stopped this bit will clear. All writes to this bit are ignored while this bit
is high.
SC
0
5.3.9
HW_CFG—Hardware Configuration Register
Offset:
74h
Size:
32 bits
This register controls the hardware configuration of the LAN9118 Ethernet Controller.
Note: The transmitter and receiver must be stopped before writing to this register. Refer to Section
3.12.9, "Stopping and Starting the Transmitter," on page 52 and Section 3.13.4, "Stopping and
Starting the Receiver," on page 56 for details on stopping the transmitter and receiver.
BITS
DESCRIPTION
31-22
21
TYPE
DEFAULT
Reserved
RO
-
Transmit Threshold Mode (TTM). This bit is used to control the transmit
threshold the MIL uses as shown in the two tables in the TR field of this
register. This bit is ignored when the SF bit is set (1).
R/W
0
R/W
0
This bit should be set to '1' when operating in 10Mbps mode, and cleared
to '0' when operating in 100Mbps mode if the SF bit cleared.
20
Store and Forward (SF). When set, this bit instructs the MIL to store a
frame of transmit data in the MIL buffer before forwarding to its final
destination.
If this bit is set, the MIL buffers the entire frame before transmitting. TTM
and TR (see bits 21,13, and 12) are treated as Don’t Cares once the SF
mode is selected.
If this bit is reset, the MAC initiates transmission before it receives the entire
frame from the HBI (Host Bus Interface). TTM and TR (see bit 21,13, and
12) determine when the MIL initiates the transmission. If the host cannot
keep up with the MAC transmitting the Ethernet Packet, there is a risk of an
Underrun Error.
SMSC LAN9118
77
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
16-19
TX FIFO Size (TX_FIF_SZ). Sets the size of the TX FIFOs in 1KB values
to a maximum of 14KB. The TX Status FIFO consumes 512 bytes of the
space allocated by TX_FIF_SIZ, and the TX data FIFO consumes the
remaining space specified by TX_FIF_SZ. The minimum size of the TX
FIFOs is 2KB (TX data and status combined). The TX data FIFO is used for
both TX data and TX commands.
R/W
5h
The RX status and data FIFOs consume the remaining space, which is
equal to 16KB – TX_FIF_SIZ. See Section 5.3.9.1, "Allowable settings for
Configurable FIFO Memory Allocation," on page 79 for more information.
15-14
Reserved
RO
-
13-12
Threshold Control Bits (TR). These control the transmit threshold values
the MIL should use. These bits are used when the SF bit is reset. The host
can program the Transmit threshold by setting these bits. The intent is to
allow the MIL to transfer data to the final destination only after the threshold
value is met.
R/W
00
Reserved
RO
-
2
32/16-bit Mode. When set, the LAN9118 is set for 32-bit operation. When
clear, it is configured for 16-bit operation. This field is the value of the
D32/nD16 strap.
RO
-
1
Soft Reset Time-out (SRST_TO). If a software reset is attempted when the
internal PHY is not in the operational state (RX_CLK and TX_CLK running),
the reset will not complete and the soft reset operation will time-out and this
bit will be set to a ‘1’. The host processor must correct the problem and
issue another soft reset.
RO
0
In 10Mbps mode (TTM = 1) the threshold is set as follows:
[13]
[12]
Threshold (DWORDS)
0
0
012h
0
1
018h
1
0
020h
1
1
028h
In 100Mbps mode (TTM = 0) the threshold is set by as follows:
11-3
Revision 1.3 (05-31-07)
[13]
[12]
Threshold (DWORDS)
0
0
020h
0
1
040h
1
0
080h
1
1
100h
78
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
0
DESCRIPTION
Soft Reset (SRST). Writing 1 generates a software initiated reset. This reset
generates a full reset of the MAC CSR’s. The SCSR’s (system command
and status registers) are reset except for any NASR bits. Soft reset also
clears any TX or RX errors (TXE/RXE). This bit is self-clearing.
TYPE
DEFAULT
SC
0
Notes:
„ Do not attempt a soft reset unless the internal PHY is fully awake and
operational. After a PHY reset, or when returning from a reduced power
state, the PHY must be given adequate time to return to the operational
state before a soft reset can be issued. The internal RX_CLK and TX_CLK
signals must be running for a proper software reset. Please refer to
Section 6.8, "Reset Timing," on page 121 for details on PHY reset timing.
„ The LAN9118 must always be read at least once after power-up, reset, or
upon return from a power-saving state or write operations will not function.
5.3.9.1
Allowable settings for Configurable FIFO Memory Allocation
TX and RX FIFO space is configurable through the CSR - HW_CFG register defined above. The user
must select the FIFO allocation by setting the TX FIFO Size (TX_FIF_SZ) field in the hardware
configuration (HW_CFG) register. The TX_FIF_SZ field selects the total allocation for the TX data path,
including the TX Status FIFO size. The TX Status FIFO size is fixed at 512 Bytes (128 TX Status
DWORDs). The TX Status FIFO length is subtracted from the total TX FIFO size with the remainder
being the TX data FIFO Size. Note that TX data FIFO space includes both commands and payload
data.
RX FIFO Size is the remainder of the unallocated FIFO space (16384 bytes – TX FIFO Size). The RX
Status FIFO size is always equal to 1/16 of the RX FIFO Size. The RX Status FIFO length is subtracted
from the total RX FIFO size with the remainder being the RX data FIFO Size.
For example, if TX_FIF_SZ = 6 then:
Total TX FIFO Size = 6144 Bytes (6KB)
TX Status FIFO Size = 512 Bytes (Fixed)
TX Data FIFO Size = 6144 – 512 = 5632 Bytes
RX FIFO Size = 16384 – 6144 = 10240 Bytes (10KB)
RX Status FIFO Size = 10240 / 16 = 640 Bytes (160 RX Status DWORDs)
RX Data FIFO Size = 10240 – 640 = 9600 Bytes
Table 5.3 shows every valid setting for the TX_FIF_SZ field. Note that settings not shown in this table
are reserved and should not be used.
Note: The RX data FIFO is considered full 4 DWORDs before the length that is specified in the
HW_CFG register.
Table 5.3 Valid TX/RX FIFO Allocations
TX_FIF_SZ
TX DATA FIFO
SIZE (BYTES)
TX STATUS FIFO
SIZE (BYTES)
RX DATA FIFO
SIZE (BYTES)
RX STATUS FIFO
SIZE (BYTES)
2
1536
512
13440
896
3
2560
512
12480
832
SMSC LAN9118
79
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 5.3 Valid TX/RX FIFO Allocations (continued)
TX_FIF_SZ
TX DATA FIFO
SIZE (BYTES)
TX STATUS FIFO
SIZE (BYTES)
RX DATA FIFO
SIZE (BYTES)
RX STATUS FIFO
SIZE (BYTES)
4
3584
512
11520
768
5
4608
512
10560
704
6
5632
512
9600
640
7
6656
512
8640
576
8
7680
512
7680
512
9
8704
512
6720
448
10
9728
512
5760
384
11
10752
512
4800
320
12
11776
512
3840
256
13
12800
512
2880
192
14
13824
512
1920
128
In addition to the host-accessible FIFOs, the MAC Interface Layer (MIL) contains an additional 2K
bytes of TX, and 128 bytes of RX FIFO buffering. These sizes are fixed, and cannot be adjusted by
the host.
As space in the TX MIL (Mac Interface Layer) FIFO frees, data is moved into it from the TX data FIFO.
Depending on the size of the frames to be transmitted, the MIL can hold up to two Ethernet frames.
This is in addition to any TX data that may be queued in the TX data FIFO.
Conversely, as data is received by the LAN9118, it is moved from the MAC to the RX MIL FIFO, and
then into the RX data FIFO. When the RX data FIFO fills up, data will continue to collect in the RX
MIL FIFO. If the RX MIL FIFO fills up and overruns, subsequent RX frames will be lost until room is
made in the RX data FIFO. For each frame of data that is lost, the RX Dropped Frames Counter
(RX_DROP) is incremented.
RX and TX MIL FIFO levels are not visible to the host processor. RX and TX MIL FIFOs operate
independent of the TX adatand RX data and status FIFOs. FIFO levels set for the RX and TX data
and Status FIFOs do not take into consideration the MIL FIFOs.
Revision 1.3 (05-31-07)
80
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.10
RX_DP_CTRL—Receive Datapath Control Register
Offset:
78h
Size:
32 bits
This register is used to discard unwanted receive frames.
BITS
31
DESCRIPTION
TYPE
DEFAULT
RX Data FIFO Fast Forward (RX_FFWD): Writing a ‘1’ to this bit causes
the RX data FIFO to fast-forward to the start of the next frame. This bit will
remain high until the RX data FIFO fast-forward operation has completed.
No reads should be issued to the RX data FIFO while this bit is high.
R/W
0h
RO
-
Note:
30-0
5.3.11
Please refer to section “Receive Data FIFO Fast Forward” on
page 54 for detailed information regarding the use of RX_FFWD.
Reserved
RX_FIFO_INF—Receive FIFO Information Register
Offset:
7Ch
Size:
32 bits
This register contains the used space in the receive FIFOs of the LAN9118 Ethernet Controller.
BITS
DESCRIPTION
TYPE
DEFAULT
31-24
Reserved
RO
-
23-16
RX Status FIFO Used Space (RXSUSED). Indicates the amount of space
in DWORDs, used in the RX Status FIFO.
RO
00h
15-0
RX Data FIFO Used Space (RXDUSED).). Reads the amount of space in
bytes, used in the RX data FIFO. For each receive frame, this field is
incremented by the length of the receive data rounded up to the nearest
DWORD (if the payload does not end on a DWORD boundary).
RO
0000h
SMSC LAN9118
81
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.12
TX_FIFO_INF—Transmit FIFO Information Register
Offset:
80h
Size:
32 bits
This register contains the free space in the transmit data FIFO and the used space in the transmit
status FIFO in the LAN9118.
BITS
DESCRIPTION
TYPE
DEFAULT
31-24
Reserved
RO
-
23-16
TX Status FIFO Used Space (TXSUSED). Indicates the amount of space
in DWORDS used in the TX Status FIFO.
RO
00h
15-0
TX Data FIFO Free Space (TDFREE). Reads the amount of space in bytes,
available in the TX data FIFO. The application should never write more data
than is available, as indicated by this value.
RO
1200h
5.3.13
PMT_CTRL— Power Management Control Register
Offset:
84h
Size:
32 bits
This register controls the Power Management features. This register can be read while the
LAN9118 is in a power saving mode.
Note: The LAN9118 must always be read at least once after power-up, reset, or upon return from a
power-saving state or write operations will not function.
BITS
DESCRIPTION
TYPE
DEFAULT
31:14
RESERVED
RO
-
13-12
Power Management Mode (PM_MODE) – These bits set the LAN9118 into
the appropriate Power Management mode. Special care must be taken when
modifying these bits.
SC
00b
Encoding:
00b – D0 (normal operation)
01b – D1 (wake-up frame and magic packet detection are enabled)
10b – D2 (can perform energy detect)
11b – RESERVED - Do not set in this mode
Note:
When the LAN9118 is in a any of the reduced power modes, a write
of any data to the BYTE_TEST register will wake-up the device. DO
NOT PERFORM WRITES TO OTHER ADDRRESSES while the
READY bit in this register is cleared.
11
RESERVED
RO
-
10
PHY Reset (PHY_RST) – Writing a ‘1’ to this bit resets the PHY. The internal
logic automatically holds the PHY reset for a minimum of 100us. When the
PHY is released from reset, this bit is automatically cleared. All writes to this
bit are ignored while this bit is high.
SC
0b
Revision 1.3 (05-31-07)
82
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
9
Wake-On-Lan Enable (WOL_EN) – When set, the PME signal (if enabled
with PME_EN) will be asserted in accordance with the PME_IND bit upon a
WOL event. When set, the PME_INT will also be asserted upon a WOL
event, regardless of the setting of the PME_EN bit.
R/W
0b
8
Energy-Detect Enable (ED_EN) - When set, the PME signal (if enabled with
PME_EN) will be asserted in accordance with the PME_IND bit upon an
Energy-Detect event. When set, the PME_INT will also be asserted upon an
Energy Detect event, regardless of the setting of the PME_EN bit.
R/W
0b
7
RESERVED
RO
-
6
PME Buffer Type (PME_TYPE) – When cleared, enables PME to function
as an open-drain buffer for use in a Wired-Or configuration. When set, the
PME output is a Push-Pull driver. When configured as an open-drain output
the PME_POL field is ignored, and the output is always active low.
R/W
NASR
0b
WAKE-UP Status (WUPS) – This field indicates the cause of a wake-up
event detection as follows
R/WC
00
R/W
0b
5-4
00b -- No wake-up event detected
01b -- Energy detected
10b -- Wake-up frame or magic packet detected
11b -- Indicates multiple events occurred
WUPS bits are cleared by writing a ‘1’ to the appropriate bit. The device must
return to the D0 state (READY bit set) before these bits can be cleared.
Note:
3
In order to clear this bit, it is required that all event sources be
cleared as well. The event sources are decribed in Figure 3.11 PME
and PME_INT Signal Generationon page 40.
PME indication (PME_IND). The PME signal can be configured as a pulsed
output or a static signal, which is asserted upon detection of a wake-up
event.
When set, the PME signal will pulse active for 50mS upon detection of a
wake-up event.
When clear, the PME signal is driven continously upon detection of a wakeup event.
The PME signal can be deactivated by clearing the WUPS bits, or by
clearing the appropriate enable (refer to Section 3.10.2.3, "Power
Managment Event Indicators," on page 40).
2
PME Polarity (PME_POL). This bit controls the polarity of the PME signal.
When set, the PME output is an active high signal. When reset, it is active
low. When PME is configured as an open-drain output this field is ignored,
and the output is always active low.
R/W
NASR
0b
1
PME Enable (PME_EN). When set, this bit enables the external PME signal.
This bit does not affect the PME interrupt (PME_INT).
R/W
0b
0
Device Ready (READY). When set, this bit indicates that LAN9118 is ready
to be accessed. This register can be read when LAN9118 is in any power
management mode. Upon waking from any power management mode,
including power-up, the host processor can interrogate this field as an
indication when LAN9118 has stabilized and is fully alive. Reads and writes
of any other address are invalid until this bit is set.
RO
-
Note:
SMSC LAN9118
With the exception of HW_CFG and PMT_CTRL, read access to
any internal resources is forbidden while the READY bit is cleared.
83
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.14
GPIO_CFG—General Purpose IO Configuration Register
Offset:
88h
Size:
32 bits
This register configures the GPIO and LED functions.
Bits
Type
Default
Reserved
RO
-
LED[3:1] enable (LEDx_EN). A ‘1’ sets the associated pin as an LED output.
When cleared low, the pin functions as a GPIO signal.
LED1/GPIO0 – bit 28
LED2/GPIO1 – bit 29
LED3/GPIO2 – bit 30
R/W
000
Reserved
RO
-
GPIO Interrupt Polarity 0-2 (GPIO_INT_POL). When set high, a high logic
level on the corresponding GPIO pin will set the corresponding INT_STS
register bit. When cleared low, a low logic level on the corresponding GPIO
pin will set the corresponding INT_STS register bit.
GPIO Interrupts must also be enabled in GPIOx_INT_EN in the INT_EN
register.
R/W
000
Reserved
RO
-
EEPROM Enable (EEPR_EN). The value of this field determines the function
of the external EEDIO and EECLK:
Please refer to Table 5.4 for the EEPROM Enable bit function definitions.
R/W
000
Reserved
RO
-
18:16
GPIO Buffer Type 0-2 (GPIOBUFn). When set, the output buffer for the
corresponding GPIO signal is configured as a push/pull driver. When cleared,
the corresponding GPIO set configured as an open-drain driver.
GPIO0 – bit 16
GPIO1 – bit 17
GPIO2 – bit 18
R/W
000
15:11
Reserved
RO
-
10:8
GPIO Direction 0-2 (GPDIRn). When set, enables the corresponding GPIO
as output. When cleared the GPIO is enabled as an input.
GPIO0 – bit 8
GPIO1 – bit 9
GPIO2 – bit 10
R/W
0000
7:5
Reserved
RO
-
31
30:28
27
26:24
Description
GPIO0 – bit 24
GPIO1 – bit 25
GPIO2 – bit 26
Note:
23
22:20
Note:
19
Revision 1.3 (05-31-07)
GPIO inputs must be active for greater than 40nS to be recognized
as interrupt inputs.
The host must not change the function of the EEDIO and EECLK
pins when an EEPROM read or write cycle is in progress. Do not
use reserved settings.
84
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Bits
Description
Type
Default
4:3
GPO Data 3-4 (GPODn). The value written is reflected on GPOn.
GPO3 – bit 3
GPO4 – bit 4
R/W
00
2:0
GPIO Data 0-2 (GPIODn). When enabled as an output, the value written is
reflected on GPIOn. When read, GPIOn reflects the current state of the
corresponding GPIO pin.
GPIO0 – bit 0
GPIO1 – bit 1
GPIO2 – bit 2
R/W
000
Table 5.4 EEPROM Enable Bit Definitions
[22]
[21]
[20]
EEDIO FUNCTION
EECLK FUNCTION
0
0
0
EEDIO
EECLK
0
0
1
GPO3
GPO4
0
1
0
0
1
1
1
0
0
1
0
1
TX_EN
GPO4
1
1
0
TX_EN
RX_DV
1
1
1
TX_CLK
RX_CLK
5.3.15
Reserved
GPO3
RX_DV
Reserved
GPT_CFG-General Purpose Timer Configuration Register
Offset:
8Ch
Size:
32 bits
This register configures the General Purpose timer. The GP Timer can be configured to generate host
interrupts at intervals defined in this register.
BITS
DESCRIPTION
TYPE
DEFAULT
31-30
Reserved
RO
-
GP Timer Enable (TIMER_EN). When a one is written to this bit the GP
Timer is put into the run state. When cleared, the GP Timer is halted. On
the 1 to 0 transition of this bit the GPT_LOAD field will be preset to FFFFh.
R/W
0
28-16
Reserved
RO
-
15-0
General Purpose Timer Pre-Load (GPT_LOAD). This value is pre-loaded
into the GP-Timer.
R/W
FFFFh
29
SMSC LAN9118
85
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.16
GPT_CNT-General Purpose Timer Current Count Register
Offset:
90h
Size:
32 bits
This register reflects the current value of the GP Timer.
BITS
DESCRIPTION
31-16
15-0
5.3.17
TYPE
DEFAULT
Reserved
RO
-
General Purpose Timer Current Count (GPT_CNT). This 16-bit field
reflects the current value of the GP Timer.
RO
FFFFh
WORD_SWAP—Word Swap Control
Offset:
98h
Size:
32 bits
This register controls how words from the host data bus are mapped to the CRSs and Data FIFOs
inside the LAN9118. The LAN9118 always sends data from the Transmit Data FIFO to the network so
that the low order word is sent first, and always receives data from the network to the Receive Data
FIFO so that the low order word is received first.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Word Swap. This field only has significance if the device is operated in 16bit mode. In 32-bit mode, D[31:15] is always mapped to the high order word
and D[15:0] is always mapped to the low order word. In 16-bit mode, if this
field is set to 00000000h, or anything except FFFFFFFFh, the LAN9118
maps words with address bit A[1]=1 to the high order words of the CSRs
and Data FIFOs, and words with address bit A[1]=0 to the low order words
of the CSRs and Data FIFOs. If this field is set to FFFFFFFFh, the LAN9118
maps words with address bit A[1]=1 to the low order words of the CSRs and
Data FIFOs, and words with address bit A[1]=0 to the high order words of
the CSRs and Data FIFOs.
R/W
NASR
00000000h
Note:
Please refer to Section 3.6, "32-bit vs. 16-bit Host Bus Width
Operation" for additional information.
Revision 1.3 (05-31-07)
86
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.18
FREE_RUN—Free-Run 25MHz Counter
Offset:
9Ch
Size:
32 bits
This register reflects the value of the free-running 25MHz counter.
BITS
DESCRIPTION
31:0
Free Running SCLK Counter (FR_CNT):
5.3.19
Note:
This field reflects the value of a free-running 32-bit counter. At reset
the counter starts at zero and is incremented for every 25MHz
cycle. When the maximum count has been reached the counter will
rollover. When read in 16-bit mode the count value is latched on
the first read. The FREE_RUN counter can take up to 160nS to
clear after a reset event.
Note:
This counter will run regardless of the power management states
D0, D1 or D2.
TYPE
DEFAULT
RO
-
TYPE
DEFAULT
RC
00000000h
RX_DROP– Receiver Dropped Frames Counter
Offset:
A0h
Size:
32 bits
This register indicates the number of receive frames that have been dropped.
BITS
DESCRIPTION
31-0
RX Dropped Frame Counter (RX_DFC). This counter is incremented every
time a receive frame is dropped. RX_DFC is cleared on any read of this
register.
An interrupt can be issued when this counter passes through its halfway
point (7FFFFFFFh to 80000000h).
SMSC LAN9118
87
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.20
MAC_CSR_CMD – MAC CSR Synchronizer Command Register
Offset:
A4h
Size:
32 bits
This register is used to control the read and write operations with the MAC CSR’s
BITS
DESCRIPTION
TYPE
DEFAULT
31
CSR Busy. When a 1 is written into this bit, the read or write operation is
performed to the specified MAC CSR. This bit will remain set until the
operation is complete. In the case of a read this means that the host can
read valid data from the data register. The MAC_CSR_CMD and
MAC_CSR_DATA registers should not be modified until this bit is cleared.
SC
0
30
R/nW. When set, this bit indicates that the host is requesting a read
operation. When clear, the host is performing a write.
R/W
0
29-8
Reserved.
RO
-
7-0
CSR Address. The 8-bit value in this field selects which MAC CSR will be
accessed with the read or write operation.
R/W
00h
5.3.21
MAC_CSR_DATA – MAC CSR Synchronizer Data Register
Offset:
A8h
Size:
32 bits
This register is used in conjunction with the MAC_CSR_CMD register to perform read and write
operations with the MAC CSR’s
BITS
DESCRIPTION
TYPE
DEFAULT
31-0
MAC CSR Data. Value read from or written to the MAC CSR’s.
R/W
00000000h
Revision 1.3 (05-31-07)
88
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.22
AFC_CFG – Automatic Flow Control Configuration Register
Offset:
ACh
Size:
32 bits
This register configures the mechanism that controls both the automatic, and software-initiated
transmission of pause frames and back pressure.
Note: The LAN9118 will not transmit pause frames or assert back pressure if the transmitter is
disabled.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
Reserved
RO
-
23:16
Automatic Flow Control High Level (AFC_HI). Specifies, in multiples of
64 bytes, the level at which flow control will trigger. When this limit is
reached the chip will apply back pressure or will transmit a pause frame as
programmed in bits [3:0] of this register.
R/W
00h
R/W
00h
During full-duplex operation only a single pause frame is transmitted when
this level is reached. The pause time transmitted in this frame is
programmed in the FCPT field of the FLOW register in the MAC CSR space.
During half-duplex operation each incoming frame that matches the criteria
in bits [3:0] of this register will be jammed for the period set in the
BACK_DUR field.
15:8
Automatic Flow Control Low Level (AFC_LO). Specifies, in multiples of
64 bytes, the level at which a pause frame is transmitted with a pause time
setting of zero. When the amount of data in the RX data FIFO falls below
this level the pause frame is transmitted. A pause time value of zero
instructs the other transmitting device to immediately resume transmission.
The zero time pause frame will only be transmitted if the RX data FIFO had
reached the AFC_HI level and a pause frame was sent. A zero pause time
frame is sent whenever automatic flow control in enabled in bits [3:0] of this
register.
Note:
When automatic flow control is enabled the AFC_LO setting must
always be less than the AFC_HI setting.
7:4
Backpressure Duration (BACK_DUR). When the LAN9118 automatically
asserts back pressure, it will be asserted for this period of time. This field
has no function and is not used in full-duplex mode. Please refer to
Table 5.5, describing Backpressure Duration bit mapping for more
information.
R/W
0h
3
Flow Control on Multicast Frame (FCMULT). When this bit is set, the
LAN9118 will assert back pressure when the AFC level is reached and a
multicast frame is received. This field has no function in full-duplex mode.
R/W
0
2
Flow Control on Broadcast Frame (FCBRD). When this bit is set, the
LAN9118 will assert back pressure when the AFC level is reached and a
broadcast frame is received. This field has no function in full-duplex mode.
R/W
0
1
Flow Control on Address Decode (FCADD). When this bit is set, the
LAN9118 will assert back pressure when the AFC level is reached and a
frame addressed to the LAN9118 is received. This field has no function in
full-duplex mode.
R/W
0
SMSC LAN9118
89
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
0
DESCRIPTION
TYPE
DEFAULT
Flow Control on Any Frame (FCANY). When this bit is set, the LAN9118
will assert back pressure, or transmit a pause frame when the AFC level is
reached and any frame is received. Setting this bit enables full-duplex flow
control when the LAN9118 is operating in full-duplex mode.
R/W
0
When this mode is enabled during half-duplex operation, the Flow Controller
does not decode the MAC address and will send a pause frame upon
receipt of a valid preamble (i.e., immediately at the beginning of the next
frame after the RX data FIFO level is reached).
When this mode is enabled during full-duplex operation, the Flow Controller
will immediately instruct the MAC to send a pause frame when the RX data
FIFO level is reached. The MAC will queue the pause frame transmission
for the next available window.
Setting this bit overrides bits [3:1] of this register.
Table 5.5 Backpressure Duration Bit Mapping
BACKPRESSURE DURATION
[19:16]
100Mbs Mode
10Mbs Mode
0h
5uS
7.2uS
1h
10uS
12.2uS
2h
15uS
17.2uS
3h
25uS
27.2uS
4h
50uS
52.2uS
5h
100uS
102.2uS
6h
150uS
152.2uS
7h
200uS
202.2uS
8h
250uS
252.2uS
9h
300uS
302.2uS
Ah
350uS
352.2uS
Bh
400uS
402.2uS
Ch
450uS
452.2uS
Dh
500uS
502.2uS
Eh
550uS
552.2uS
Fh
600uS
602.2uS
Revision 1.3 (05-31-07)
90
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.3.23
E2P_CMD – EEPROM Command Register
Offset:
B0h
Size:
32 bits
This register is used to control the read and write operations with the Serial EEPROM.
BITS
31
DESCRIPTION
EPC Busy: When a 1 is written into this bit, the operation specified in the
EPC command field is performed at the specified EEPROM address. This
bit will remain set until the operation is complete. In the case of a read this
means that the host can read valid data from the E2P data register. The
E2P_CMD and E2P_DATA registers should not be modified until this bit is
cleared. In the case where a write is attempted and an EEPROM is not
present, the EPC Busy remains busy until the EPC Time-out occurs. At that
time the busy bit is cleared.
Note:
SMSC LAN9118
TYPE
DEFAULT
SC
0
EPC busy will be high immediately following power-up or reset.
After the EEPROM controller has finished reading (or attempting to
read) the MAC address from the EEPROM the EPC Busy bit is
cleared.
91
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
30-28
EPC command. This field is used to issue commands to the EEPROM
controller. The EPC will execute commands when the EPC Busy bit is set.
A new command must not be issued until the previous command completes.
This field is encoded as follows:
R/W
0
RO
-
[30]
[29]
[28]
OPERATION
0
0
0
READ
0
0
1
EWDS
0
1
0
EWEN
0
1
1
WRITE
1
0
0
WRAL
1
0
1
ERASE
1
1
0
ERAL
1
1
1
Reload
READ (Read Location): This command will cause a read of the EEPROM
location pointed to by EPC Address. The result of the read is available in
the E2P_DATA register.
EWDS (Erase/Write Disable): After issued, the EEPROM will ignore erase
and write commands. To re-enable erase/write operations issue the EWEN
command.
EWEN (Erase/Write Enable): Enables the EEPROM for erase and write
operations. The EEPROM will allow erase and write operations until the
Erase/Write Disable command is sent, or until power is cycled.
Note:
The EEPROM device will power-up in the erase/write-disabled
state. Any erase or write operations will fail until an Erase/Write
Enable command is issued.
WRITE (Write Location): If erase/write operations are enabled in the
EEPROM, this command will cause the contents of the E2P_DATA register
to be written to the EEPROM location selected by the EPC Address field.
WRAL (Write All): If erase/write operations are enabled in the EEPROM,
this command will cause the contents of the E2P_DATA register to be
written to every EEPROM memory location.
ERASE (Erase Location): If erase/write operations are enabled in the
EEPROM, this command will erase the location selected by the EPC
Address field.
ERAL (Erase All): If erase/write operations are enabled in the EEPROM,
this command will initiate a bulk erase of the entire EEPROM.
RELOAD (MAC Address Reload): Instructs the EEPROM controller to
reload the MAC address from the EEPROM. If a value of 0xA5 is not found
in the first address of the EEPROM, the EEPROM is assumed to be unprogrammed and MAC Address Reload operation will fail. The “MAC
Address Loaded” bit indicates a successful load of the MAC address.
27-10
Reserved.
Revision 1.3 (05-31-07)
92
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
9
DESCRIPTION
TYPE
DEFAULT
EPC Time-out. If an EEPROM operation is performed, and there is no
R/WC
0
RO
-
R/W
00h
response from the EEPROM within 30mS, the EEPROM controller will timeout and return to its idle state. This bit is set when a time-out occurs
indicating that the last operation was unsuccessful.
Note:
8
If the EEDIO signal pin is externally pulled-high, EPC commands
will not time out if the EEPROM device is missing. In this case the
EPC Busy bit will be cleared as soon as the command sequence
is complete. It should also be noted that the ERASE, ERAL,
WRITE and WRAL commands are the only EPC commands that
will time-out if an EEPROM device is not present -and- the EEDIO
signal is pulled low
MAC Address Loaded. When set, this bit indicates that a valid EEPROM
was found, and that the MAC address programming has completed
normally. This bit is set after a successful load of the MAC address after
power-up, or after a RELOAD command has completed
7-0
EPC Address. The 8-bit value in this field is used by the EEPROM
Controller to address the specific memory location in the Serial EEPROM.
This is a Byte aligned address.
5.3.24
E2P_DATA – EEPROM Data Register
Offset:
B4h
Size:
32 bits
This register is used in conjunction with the E2P_CMD register to perform read and write operations
with the Serial EEPROM
BITS
DESCRIPTION
31-8
7:0
TYPE
DEFAULT
Reserved.
RO
-
EEPROM Data. Value read from or written to the EEPROM.
R/W
00h
5.4
MAC Control and Status Registers
These registers are located in the MAC module and are accessed indirectly through the MAC-CSR
synchronizer port. Table 5.6, "LAN9118 MAC CSR Register Map", shown below, lists the MAC registers
that are accessible through the indexing method using the MAC_CSR_CMD and MAC_CSR_DATA
registers (see sections MAC_CSR_CMD – MAC CSR Synchronizer Command Register and
MAC_CSR_DATA – MAC CSR Synchronizer Data Register).
SMSC LAN9118
93
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 5.6 LAN9118 MAC CSR Register Map
MAC CONTROL AND STATUS REGISTERS
INDEX
SYMBOL
1
MAC_CR
2
REGISTER NAME
DEFAULT
MAC Control Register
00040000h
ADDRH
MAC Address High
0000FFFFh
3
ADDRL
MAC Address Low
FFFFFFFFh
4
HASHH
Multicast Hash Table High
00000000h
5
HASHL
Multicast Hash Table Low
00000000h
6
MII_ACC
MII Access
00000000h
7
MII_DATA
MII Data
00000000h
8
FLOW
Flow Control
00000000h
9
VLAN1
VLAN1 Tag
00000000h
A
VLAN2
VLAN2 Tag
00000000h
B
WUFF
Wake-up Frame Filter
00000000h
C
WUCSR
Wake-up Control and Status
00000000h
5.4.1
MAC_CR—MAC Control Register
Offset:
1
Attribute:
R/W
Default Value:
00040000h
Size:
32 bits
This register establishes the RX and TX operation modes and controls for address filtering and packet
filtering.
BITS
DESCRIPTION
31
Receive All Mode (RXALL). When set, all incoming packets will be received and passed on to the
address filtering Function for processing of the selected filtering mode on the received frame. Address
filtering then occurs and is reported in Receive Status. When reset, only frames that pass Destination
Address filtering will be sent to the Application.
30-24
Reserved
23
Disable Receive Own (RCVOWN). When set, the MAC disables the reception of frames when the
MII TX_EN signal is asserted. The MAC blocks the transmitted frame on the receive path. When reset,
the MAC receives all packets the PHY gives, including those transmitted by the MAC.This bit should
be reset when the Full Duplex Mode bit is set.
22
Reserved
Revision 1.3 (05-31-07)
94
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
DESCRIPTION
21
Loopback operation Mode (LOOPBK). Selects the loop back operation modes for the MAC. This is
only for full duplex mode
1’b0: Normal: No feedback
1’b1: Internal: Through MII
In internal loopback mode, the TX frame is received by the Internal MII interface, and sent back to
the MAC without being sent to the PHY.
Note:
When enabling or disabling the loopback mode it can take up to 10μs for the mode change
to occur. The transmitter and receiver must be stopped and disabled when modifying the
LOOPBK bit. The transmitter or receiver should not be enabled within10μs of modifying the
LOOPBK bit.
20
Full Duplex Mode (FDPX). When set, the MAC operates in Full-Duplex mode, in which it can transmit
and receive simultaneously. In Full-Duplex mode, the heartbeat check is disabled and the heartbeat
fail status should thus be ignored.
19
Pass All Multicast (MCPAS). When set, indicates that all incoming frames with a Multicast destination
address (first bit in the destination address field is 1) are received. Incoming frames with physical
address (Individual Address/Unicast) destinations are filtered and received only if the address matches
the MAC Address.
18
Promiscuous Mode (PRMS). When set, indicates that any incoming frame is received regardless of
its destination address.
17
Inverse filtering (INVFILT). When set, the address check Function operates in Inverse filtering mode.
This is valid only during Perfect filtering mode.
16
Pass Bad Frames (PASSBAD). When set, all incoming frames that passed address filtering are
received, including runt frames, collided frames or truncated frames caused by buffer underrun.
15
Hash Only Filtering mode (HO). When set, the address check Function operates in the Imperfect
Address Filtering mode both for physical and multicast addresses
14
Reserved
13
Hash/Perfect Filtering Mode (HPFILT). When reset (0), the LAN9118 will implement a perfect
address filter on incoming frames according the address specified in the MAC address register.
When set (1), the address check Function does imperfect address filtering of multicast incoming
frames according to the hash table specified in the multicast hash table register.
If the Hash Only Filtering mode (HO) bit is set (1), then the physical (IA) are imperfect filtered too. If
the Hash Only Filtering mode (HO) bit is reset (0), then the IA addresses are perfect address filtered
according to the MAC Address register
12
Late Collision Control (LCOLL). When set, enables retransmission of the collided frame even after
the collision period (late collision). When reset, the MAC disables frame transmission on a late
collision. In any case, the Late Collision status is appropriately updated in the Transmit Packet status.
11
Disable Broadcast Frames (BCAST). When set, disables the reception of broadcast frames. When
reset, forwards all broadcast frames to the application.
10
Disable Retry (DISRTY). When set, the MAC attempts only one transmission. When a collision is
seen on the bus, the MAC ignores the current frame and goes to the next frame and a retry error is
reported in the Transmit status. When reset, the MAC attempts 16 transmissions before signaling a
retry error.
9
Reserved
8
Automatic Pad Stripping (PADSTR). When set, the MAC strips the pad field on all incoming frames,
if the length field is less than 46 bytes. The FCS field is also stripped, since it is computed at the
transmitting station based on the data and pad field characters, and is invalid for a received frame
that has had the pad characters stripped. Receive frames with a 46-byte or greater length field are
passed to the Application unmodified (FCS is not stripped). When reset, the MAC passes all incoming
frames to the host unmodified.
SMSC LAN9118
95
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
DESCRIPTION
7-6
BackOff Limit (BOLMT). The BOLMT bits allow the user to set its back-off limit in a relaxed or
aggressive mode. According to IEEE 802.3, the MAC has to wait for a random number [r] of slottimes** after it detects a collision, where:
(eq.1)0 < r < 2K
The exponent K is dependent on how many times the current frame to be transmitted has been retried,
as follows:
(eq.2)K = min (n, 10) where n is the current number of retries.
If a frame has been retried three times, then K = 3 and r= 8 slot-times maximum. If it has been retried
12 times, then K = 10, and r = 1024 slot-times maximum.
An LFSR (linear feedback shift register) 20-bit counter emulates a 20bit random number generator,
from which r is obtained. Once a collision is detected, the number of the current retry of the current
frame is used to obtain K (eq.2). This value of K translates into the number of bits to use from the
LFSR counter. If the value of K is 3, the MAC takes the value in the first three bits of the LFSR counter
and uses it to count down to zero on every slot-time. This effectively causes the MAC to wait eight
slot-times. To give the user more flexibility, the BOLMT value forces the number of bits to be used
from the LFSR counter to a predetermined value as in the table below.
BOLMT Value
# Bits Used from LFSR Counter
2’b00
10
2’b01
8
2’b10
4
2’b11
1
Thus, if the value of K = 10, the MAC will look at the BOLMT if it is 00, then use the lower ten bits of the LFSR
counter for the wait countdown. If the BOLMT is 10, then it will only use the value in the first four bits for the
wait countdown, etc.
**Slot-time = 512 bit times. (See IEEE 802.3 Spec., Secs. 4.2.3.25 and 4.4.2.1)
5
Deferral Check (DFCHK). When set, enables the deferral check in the MAC. The MAC will abort the
transmission attempt if it has deferred for more than 24,288 bit times. Deferral starts when the
transmitter is ready to transmit, but is prevented from doing so because the CRS is active. Defer time
is not cumulative. If the transmitter defers for 10,000 bit times, then transmits, collides, backs off, and
then has to defer again after completion of back-off, the deferral timer resets to 0 and restarts. When
reset, the deferral check is disabled in the MAC and the MAC defers indefinitely.
4
Reserved
3
Transmitter enable (TXEN). When set, the MAC’s transmitter is enabled and it will transmit frames
from the buffer onto the cable.
When reset, the MAC’s transmitter is disabled and will not transmit any frames.
2
Receiver Enable (RXEN). When set (1), the MAC’s receiver is enabled and will receive frames from
the internal PHY.
When reset, the MAC’s receiver is disabled and will not receive any frames from the internal PHY.
1-0
5.4.2
Reserved
ADDRH—MAC Address High Register
Offset:
2
Attribute:
R/W
Default Value:
0000FFFFh
Size:
32 bits
The MAC Address High register contains the upper 16-bits of the physical address of the MAC. The
contents of this register are optionally loaded from the EEPROM at power-on through the EEPROM
Controller if a programmed EEPROM is detected. The least significant byte of this register (bits [7:0])
Revision 1.3 (05-31-07)
96
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
is loaded from address 0x05 of the EEPROM. The second byte (bits [15:8]) is loaded from address
0x06 of the EEPROM. Please refer to Section 4.6 for more information on the EEPROM. Section 5.4.3
details the byte ordering of the ADDRL and ADDRH registers with respect to the reception of the
Ethernet physical address.
BITS
DESCRIPTION
31-16
Reserved
15-0
Physical Address [47:32]. This field contains the upper 16-bits (47:32) of the Physical Address of
the LAN9118 device. The content of this field is undefined until loaded from the EEPROM at poweron. The host can update the contents of this field after the initialization process has completed.
5.4.3
ADDRL—MAC Address Low Register
Offset:
3
Attribute:
R/W
Default Value:
FFFFFFFFh
Size:
32 bits
The MAC Address Low register contains the lower 32 bits of the physical address of the MAC. The
contents of this register are optionally loaded from the EEPROM at power-on through the EEPROM
Controller if a programmed EEPROM is detected. The least significant byte of this register (bits [7:0])
is loaded from address 0x01 of the EEPROM. The most significant byte of this register is loaded from
address 0x04 of the EEPROM. Please refer to Section 4.6 for more information on the EEPROM.
BITS
DESCRIPTION
31-0
Physical Address [31:0]. This field contains the lower 32 bits (31:0) of the Physical Address of the
LAN9118 device. The content of this field is undefined until loaded from the EEPROM at power-on.
The host can update the contents of this field after the initialization process has completed.
Table 5.7 below illustrates the byte ordering of the ADDRL and ADDRH registers with respect to the
reception of the Ethernet physical address. Also shown is the correlation between the EEPROM
addresses and ADDRL and ADDRH registers.
Table 5.7 ADDRL, ADDRH and EEPROM Byte Ordering
EEPROM ADDRESS
ADDRN
ORDER OF RECEPTION ON
ETHERNET
0x01
ADDRL[7:0]
1st
0x02
ADDRL[15:8]
2nd
0x03
ADDRL[23:16]
3rd
0x04
ADDRL[31:24]
4th
0x05
ADDRH[7:0]
5th
0x06
ADDRH[15:8]
6th
SMSC LAN9118
97
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
As an example, if the desired Ethernet physical address is 12-34-56-78-9A-BC, the ADDRL and
ADDRH registers would be programmed as shown in Figure 5.2. The values required to automatically
load this configuration from the EEPROM are also shown.
31
24 23
xx
16 15
xx
8 7
0xBC
0
0x9A
ADDRH
31
0x78
24 23
16 15
0x56
8 7
0x34
0
0x12
0x06
0xBC
0x05
0x9A
0x04
0x78
0x03
0x56
0x02
0x34
0x01
0x12
0x00
0xA5
EEPROM
ADDRL
Figure 5.2 Example ADDRL, ADDRH and EEPROM Setup
Note: By convention, the left most byte of the Ethernet address (in this example 0x12) is the most
significant byte and is transmitted/received first.
5.4.4
HASHH—Multicast Hash Table High Register
Offset:
4
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
The 64-bit Multicast table is used for group address filtering. For hash filtering, the contents of the
destination address in the incoming frame is used to index the contents of the Hash table. The most
significant bit determines the register to be used (Hi/Low), while the other five bits determine the bit
within the register. A value of 00000 selects Bit 0 of the Multicast Hash Table Lo register and a value
of 11111 selects the Bit 31 of the Multicast Hash Table Hi register.
If the corresponding bit is 1, then the multicast frame is accepted. Otherwise, it is rejected. If the “Pass All
Multicast” (MCPAS) bit is set (1), then all multicast frames are accepted regardless of the multicast hash
values.
The Multicast Hash Table Hi register contains the higher 32 bits of the hash table and the Multicast
Hash Table Low register contains the lower 32 bits of the hash table.
BITS
31-0
DESCRIPTION
Upper 32 bits of the 64-bit Hash Table
Revision 1.3 (05-31-07)
98
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.4.5
HASHL—Multicast Hash Table Low Register
Offset:
5
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register defines the lower 32-bits of the Multicast Hash Table. Please refer to Table 5.4.4,
"HASHH—Multicast Hash Table High Register" for further details.
BITS
31-0
5.4.6
DESCRIPTION
Lower 32 bits of the 64-bit Hash Table
MII_ACC—MII Access Register
Offset:
6
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register is used to control the Management cycles to the PHY.
BITS
DESCRIPTION
31-16
Reserved
15-11
PHY Address: For every access to this register, this field must be set to 00001b.
10-6
MII Register Index (MIIRINDA): These bits select the desired MII register in the PHY.
5-2
Reserved
1
MII Write (MIIWnR): Setting this bit tells the PHY that this will be a write operation using the MII data
register. If this bit is not set, this will be a read operation, packing the data in the MII data register.
0
MII Busy (MIIBZY): This bit must be polled to determine when the MII register accesss is complete.
This bit must read a logical 0 before writing to this register and MII data register.
The LAN driver software must set (1) this bit in order for the LAN9118 to read or write any of the MII
PHY registers.
During a MII register access, this bit will be set, signifying a read or write access is in progress. The
MII data register must be kept valid until the MAC clears this bit during a PHY write operation. The
MII data register is invalid until the MAC has cleared this bit during a PHY read operation.
SMSC LAN9118
99
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.4.7
MII_DATA—MII Data Register
Offset:
7
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register contains either the data to be written to the PHY register specified in the MII Access
Register, or the read data from the PHY register whose index is specified in the MII Access Register.
BITS
DESCRIPTION
31-16
Reserved
15-0
MII Data. This contains the 16-bit value read from the PHY read operation or the 16-bit data value to
be written to the PHY before an MII write operation.
5.4.8
FLOW—Flow Control Register
Offset:
8
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register controls the generation and reception of the Control (Pause command) frames by the
MAC’s flow control block. The control frame fields are selected as specified in the 802.3x Specification
and the Pause-Time value from this register is used in the “Pause Time” field of the control frame. In
full-duplex mode the FCBSY bit is set until the control frame is transferred onto the cable. In halfduplex mode FCBSY is set while back pressure is being asserted. The host has to make sure that the
Busy bit is cleared before writing the register. The Pass Control Frame bit (FCPASS) does not affect
the sending of the frames, including Control Frames, to the Application Interface. The Flow Control
Enable (FCEN) bit enables the receive portion of the Flow Control block.
This register is used in conjunction with the AFC_CFG register in the Slave CSRs to configure flow
control. Software flow control is initiated using the AFC_CFG register.
Note: The LAN9118 will not transmit pause frames or assert back pressure if the transmitter is
disabled.
BITS
DESCRIPTION
31-16
Pause Time (FCPT). This field indicates the value to be used in the PAUSE TIME field in the control
frame. This field must be initialized before full-duplex automatic flow control is enabled.
15-3
Reserved
Revision 1.3 (05-31-07)
100
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
DESCRIPTION
2
Pass Control Frames (FCPASS). When set, the MAC sets the Packet Filter bit in the Receive packet
status to indicate to the Application that a valid Pause frame has been received. The Application must
accept or discard a received frame based on the Packet Filter control bit. The MAC receives, decodes
and performs the Pause function when a valid Pause frame is received in Full-Duplex mode and when
flow control is enabled (FCE bit set). When reset, the MAC resets the Packet Filter bit in the Receive
packet status.
The MAC always passes the data of all frames it receives (including Flow Control frames) to the
Application. Frames that do not pass Address filtering, as well as frames with errors, are passed to
the Application. The Application must discard or retain the received frame’s data based on the
received frame’s STATUS field. Filtering modes (Promiscuous mode, for example) take precedence
over the FCPASS bit.
1
Flow Control Enable (FCEN). When set, enables the MAC Flow Control function. The MAC decodes
all incoming frames for control frames; if it receives a valid control frame (PAUSE command), it
disables the transmitter for a specified time (Decoded pause time x slot time). When reset, the MAC
flow control function is disabled; the MAC does not decode frames for control frames.
Note:
0
Flow Control is applicable when the MAC is set in Full Duplex Mode. In Half-Duplex mode,
this bit enables the Backpressure function to control the flow of received frames to the MAC.
Flow Control Busy (FCBSY). This bit is set high whenever a pause frame or back pressure is being
transmitted. This bit should read logical 0 before writing to the Flow Control (FLOW) register. During
a transfer of Control Frame, this bit continues to be set, signifying that a frame transmission is in
progress. After the PAUSE control frame’s transmission is complete, the MAC resets to 0.
Notes:
„ When writing this register the FCBSY bit must always be zero.
„ Applications must always write a zero to this bit
5.4.9
VLAN1—VLAN1 Tag Register
Offset:
9
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register contains the VLAN tag field to identify VLAN1 frames. For VLAN frames the legal frame
length is increased from 1518 bytes to 1522 bytes.
BITS
DESCRIPTION
31-16
Reserved
15-0
VLAN1 Tag Identifier (VTI1). This contains the VLAN Tag field to identify the VLAN1 frames. This
field is compared with the 13th and 14th bytes of the incoming frames for VLAN1 frame detection.
If used, this register must be set to 0x8100.
SMSC LAN9118
101
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.4.10
VLAN2—VLAN2 Tag Register
Offset:
A
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register contains the VLAN tag field to identify VLAN2 frames. For VLAN frames the legal frame
length is increased from 1518 bytes to 1522 bytes.
BITS
DESCRIPTION
31-16
Reserved
15-0
VLAN2 Tag Identifier (VTI2). This contains the VLAN Tag field to identify the VLAN2 frames. This
field is compared with the 13th and 14th bytes of the incoming frames for VLAN2 frame detection.If
used, this register must be set to 0x8100.
5.4.11
WUFF—Wake-up Frame Filter
Offset:
B
Attribute:
WO
Default Value:
00000000h
Size:
32 bits
This register is used to configure the wake up frame filter.
BITS
DESCRIPTION
31-0
Wake-Up Frame Filter (WFF). Wake-Up Frame Filter (WFF). The Wake-up frame filter is configured
through this register using an indexing mechanism. After power-on reset, hardware reset, or soft reset,
the MAC loads the first value written to this location to the first DWORD in the Wake-up frame filter
(filter 0 byte mask). The second value written to this location is loaded to the second DWORD in the
wake-up frame filter (filter 1 byte mask) and so on. Once all eight DWORDs have been written, the
internal pointer will once again point to the first entry and the filter entries can be modified in the same
manner.
Note:
Revision 1.3 (05-31-07)
This is a write-only register.
102
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.4.12
WUCSR—Wake-up Control and Status Register
Offset:
C
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register contains data pertaining to the MAC’s remote wake-up status and capabilities.
BITS
31-10
9
DESCRIPTION
Reserved
Global Unicast Enable (GUE). When set, the MAC wakes up from power-saving mode on receipt of
a global unicast frame. A global unicast frame has the MAC Address [1:0] bit set to 0.
8-7
Reserved
6
Remote Wake-Up Frame Received (WUFR). The MAC, upon receiving a valid Remote Wake-up
frame, sets this bit..
5
Magic Packet Received (MPR). Tthe MAC, upon receiving a valid Magic Packet, sets this bit.
4-3
Reserved
2
Wake-Up Frame enabled (WUEN). When set, Remote Wake-Up mode is enabled and the MAC is
capable of detecting wake-up frames as programmed in the wake-up frame filter.
1
Magic Packet Enable (MPEN). When set, Magic Packet Wake-up mode is enabled.
0
Reserved
5.5
PHY Registers
The PHY registers are not memory mapped. These registers are accessed indirectly through the MAC
via the MII_ACC and MII_DATA registers. An index must be used to access individual PHY registers.
PHY Register Indexes are shown in Table 5.8, "LAN9118 PHY Control and Status Register"below.
Note: The NASR (Not Affected by Software Reset) designation is only applicable when bit 15 of
the PHY Basic Control Register (Reset) is set.
Table 5.8 LAN9118 PHY Control and Status Register
PHY CONTROL AND STATUS REGISTERS
INDEX
(IN DECIMAL)
REGISTER NAME
0
Basic Control Register
1
Basic Status Register
2
PHY Identifier 1
3
PHY Identifier 2
SMSC LAN9118
103
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 5.8 LAN9118 PHY Control and Status Register (continued)
PHY CONTROL AND STATUS REGISTERS
INDEX
(IN DECIMAL)
5.5.1
REGISTER NAME
4
Auto-Negotiation Advertisement Register
5
Auto-Negotiation Link Partner Ability Register
6
Auto-Negotiation Expansion Register
17
Mode Control/Status Register
18
Special Modes Register
27
Special Control/Status Indications
29
Interrupt Source Register
30
Interrupt Mask Register
31
PHY Special Control/Status Register
Basic Control Register
Index (In Decimal):
BITS
0
Size:
16-bits
DESCRIPTION
TYPE
DEFAULT
RW/SC
0
15
Reset. 1 = software reset. Bit is self-clearing. For best results, when setting
this bit do not set other bits in this register.
14
Loopback. 1 = loopback mode, 0 = normal operation
RW
0
13
Speed Select. 1 = 100Mbps, 0 = 10Mbps. Ignored if Auto Negotiation is
enabled (0.12 = 1).
RW
See Note 5.1
12
Auto-Negotiation Enable. 1 = enable auto-negotiate process (overrides
0.13 and 0.8) 0 = disable auto-negotiate process.
RW
See Note 5.1
11
Power Down. 1 = General power down-mode, 0 = normal operation.
RW
0
RO
0
RW/SC
0
RW
0
Note:
After this bit is cleared, the PHY may auto-negotiate with it's
partner station. This process may take a few seconds to complete.
Once auto-negotiation is complete, bit 5 of the PHY's Basic Status
Register will be set.
10
Reserved
9
Restart Auto-Negotiate. 1 = restart auto-negotiate process 0 = normal
operation. Bit is self-clearing.
8
Duplex Mode. 1 = full duplex, 0 = half duplex. Ignored if Auto Negotiation
is enabled (0.12 = 1).
Revision 1.3 (05-31-07)
104
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
7
6-0
DESCRIPTION
TYPE
DEFAULT
Collision Test. 1 = enable COL test, 0 = disable COL test
RW
0
Reserved
RO
0
Note 5.1
5.5.2
This default value of this bit is determined by Pin 74 "SPEED_SEL". Please refer to the
pin description section for more details
Basic Status Register
Index (In Decimal):
BITS
1
Size:
16-bits
DESCRIPTION
TYPE
DEFAULT
15
100Base-T4. 1 = T4 able, 0 = no T4 ability
RO
0
14
100Base-TX Full Duplex. 1 = TX with full duplex, 0 = no TX full duplex
ability.
RO
1
13
100Base-TX Half Duplex. 1 = TX with half duplex, 0 = no TX half duplex
ability.
RO
1
12
10Base-T Full Duplex. 1 = 10Mbps with full duplex 0 = no 10Mbps with full
duplex ability
RO
1
11
10Base-T Half Duplex. 1 = 10Mbps with half duplex 0 = no 10Mbps with
half duplex ability
RO
1
Reserved
RO
0
5
Auto-Negotiate Complete. 1 = auto-negotiate process completed 0 = autonegotiate process not completed
RO
0
4
Remote Fault. 1 = remote fault condition detected 0 = no remote fault
RO/LH
0
3
Auto-Negotiate Ability. 1 = able to perform auto-negotiation function 0 =
unable to perform auto-negotiation function
RO
1
2
Link Status. 1 = link is up, 0 = link is down
RO/LL
0
1
Jabber Detect. 1 = jabber condition detected 0 = no jabber condition
detected
RO/LH
0
0
Extended Capabilities. 1 = supports extended capabilities registers 0 =
does not support extended capabilities registers.
RO
1
10-6
SMSC LAN9118
105
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.5.3
PHY Identifier 1
Index (In Decimal):
2
Size:
BITS
DESCRIPTION
15-0
PHY ID Number. Assigned to the 3rd through 18th bits of the
Organizationally Unique Identifier (OUI), respectively.
5.5.4
16-bits
TYPE
DEFAULT
RO
0x0007h
TYPE
DEFAULT
0xC0D1h
PHY Identifier 2
Index (In Decimal):
3
Size:
16-bits
BITS
DESCRIPTION
15-10
PHY ID Number b. Assigned to the 19th through 24th bits of the OUI.
RO
9-4
Model Number. Six-bit manufacturer’s model number.
RO
3-0
Revision Number. Four-bit manufacturer’s revision number.
RO
5.5.5
Auto-negotiation Advertisement
Index (In Decimal):
BITS
4
Size:
16-bits
DESCRIPTION
TYPE
DEFAULT
15
Next Page. 1 = next page capable, 0 = no next page ability. This device
does not support next page ability.
RO
0
14
Reserved
RO
0
13
Remote Fault. 1 = remote fault detected, 0 = no remote fault
R/W
0
12
Reserved
R/W
0
Pause Operation.
00 No PAUSE
01 Symmetric PAUSE
10 Asymmetric PAUSE
11 Both Symmetric PAUSE and Asymmetric PAUSE
R/W
00
100Base-T4. 1 = T4 able, 0 = no T4 ability This device does not support
100Base-T4.
RO
0
11-10
9
Revision 1.3 (05-31-07)
106
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
8
100Base-TX Full Duplex. 1 = TX with full duplex, 0 = no TX full duplex
ability
R/W
See
Note 5.2
7
100Base-TX. 1 = TX able, 0 = no TX ability
R/W
1
6
10Base-T Full Duplex.
1 = 10Mbps with full duplex
0 = no 10Mbps with full duplex ability
R/W
See
Note 5.2
5
10Base-T. 1 = 10Mbps able, 0 = no 10Mbps ability
R/W
See
Note 5.2
Selector Field. [00001] = IEEE 802.3
R/W
00001
4:0
Note 5.2
5.5.6
This default value of this bit is determined by Pin 74 "SPEED_SEL". Please refer to the
pin description section for more details.
Auto-negotiation Link Partner Ability
Index (In Decimal):
BITS
5
Size:
16-bits
DESCRIPTION
TYPE
DEFAULT
15
Next Page. 1 = next page capable, 0 = no next page ability. This device
does not support next page ability.
RO
0
14
Acknowledge. 1 = link code word received from partner 0 = link code word
not yet received
RO
0
Note:
This bit will always read 0
13
Remote Fault. 1 = remote fault detected, 0 = no remote fault
RO
0
12
Reserved
RO
0
Pause Operation.
00 No PAUSE supported by partner station
01 Symmetric PAUSE supported by partner station
10 Asymmetric PAUSE supported by partner station
11 Both Symmetric PAUSE and Asymmetric PAUSE supported by partner
station
RO
00
9
100Base-T4. 1 = T4 able, 0 = no T4 ability
RO
0
8
100Base-TX Full Duplex. 1 = TX with full duplex, 0 = no TX full duplex
ability
RO
0
7
100Base-TX. 1 = TX able, 0 = no TX ability
RO
0
6
10Base-T Full Duplex.
1 = 10Mbps with full duplex
0 = no 10Mbps with full duplex ability
RO
0
5
10Base-T. 1 = 10Mbps able, 0 = no 10Mbps ability
RO
0
Selector Field. [00001] = IEEE 802.3
RO
00001
11-10
4:0
SMSC LAN9118
107
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.5.7
Auto-negotiation Expansion
Index (In Decimal):
BITS
DESCRIPTION
15:5
Reserved
6
Size:
16-bits
TYPE
DEFAULT
RO
0
4
Parallel Detection Fault.
1 = fault detected by parallel detection logic
0 = no fault detected by parallel detection logic
RO/LH
0
3
Link Partner Next Page Able.
1 = link partner has next page ability
0 = link partner does not have next page ability
RO
0
2
Next Page Able.
1 = local device has next page ability
0 = local device does not have next page ability
RO
0
1
Page Received.
1 = new page received
0 = new page not yet received
RO/LH
0
0
Link Partner Auto-Negotiation Able.
1 = link partner has auto-negotiation ability
0 = link partner does not have auto-negotiation ability
RO
0
TYPE
DEFAULT
5.5.8
Mode Control/Status
Index (In Decimal):
17
Size:
16-bits
BITS
DESCRIPTION
15-14
Reserved. Write as 0; ignore on read.
RW
0
EDPWRDOWN. Enable the Energy Detect Power-Down mode:
0=Energy Detect Power-Down is disabled
1=Energy Detect Power-Down is enabled
RW
0
Reserved. Write as 0, ignore on read
RW
0
1
ENERGYON. Indicates whether energy is detected This bit goes to a “0” if
no valid energy is detected within 256ms. Reset to “1” by hardware reset,
unaffected by SW reset.
RO
1
0
Reserved. Write as “0”. Ignore on read.
RW
0
13
12-2
Revision 1.3 (05-31-07)
108
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.5.9
Special Modes
Index (In Decimal):
ADDRESS
18
Size:
16-bits
DESCRIPTION
TYPE
DEFAULT
15-8
Reserved
RW,
NASR
7:5
MODE: PHY Mode of operation. Refer to Table 5.9 for more details.
RW,
NASR
See
Table 5.9
4:0
PHYAD: PHY Address:
The PHY Address is used for the SMI address.
RW,
NASR
00001b
Table 5.9 MODE Control
DEFAULT REGISTER BIT VALUES
MODE
MODE DEFINITIONS
REGISTER 0
REGISTER 4
[13,12,10,8]
[8,7,6,5]
000
10Base-T Half Duplex. Auto-negotiation disabled.
0000
N/A
001
10Base-T Full Duplex. Auto-negotiation disabled.
0001
N/A
010
100Base-TX Half Duplex. Auto-negotiation disabled.
CRS is active during Transmit & Receive.
1000
N/A
011
100Base-TX Full Duplex. Auto-negotiation disabled.
CRS is active during Receive.
1001
N/A
100
100ase-TX Half Duplex is advertised. Autonegotiation enabled.
CRS is active during Transmit & Receive.
1100
0100
101
Repeater mode. Auto-negotiation enabled.
100Base-TX Half Duplex is advertised.
CRS is active during Receive.
1100
0100
110
Reserved - Do not set the LAN9118 in this mode.
N/A
N/A
111
All capable. Auto-negotiation enabled.
X10X
1111
SMSC LAN9118
109
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.5.10
Special Control/Status Indications
Index (In Decimal):
ADDRESS
15:11
27
Size:
16-bits
DESCRIPTION
Reserved: Write as 0. Ignore on read.
MODE
DEFAULT
RW
0
RW,
NASR
0
10
VCOOFF_LP: Forces the Receive PLL 10M to lock on the reference clock
at all times:
0 - Receive PLL 10M can lock on reference or line as needed (normal
operation)
1 - Receive PLL 10M is locked on the reference clock.
In this mode 10M data packets cannot be received.
9-5
Reserved: Write as 0. Ignore on read.
RW
0
4
XPOL: Polarity state of the 10Base-T:
0 - Normal polarity
1 - Reversed polarity
RO
0
Reserved: Read only - Writing to these bits have no effect.
RO
1011b
3:0
5.5.11
Interrupt Source Flag
Index (In Decimal):
29
Size:
16-bits
BITS
DESCRIPTION
TYPE
DEFAULT
15-8
Reserved. Ignore on read.
RO/LH
0
7
INT7. 1= ENERGYON generated, 0= not source of interrupt
RO/LH
0
6
INT6. 1= Auto-Negotiation complete, 0= not source of interrupt
RO/LH
0
5
INT5. 1= Remote Fault Detected, 0= not source of interrupt
RO/LH
0
4
INT4. 1= Link Down (link status negated), 0= not source of interrupt
RO/LH
0
3
INT3. 1= Auto-Negotiation LP Acknowledge, 0= not source of interrupt
RO/LH
0
2
INT2. 1= Parallel Detection Fault, 0= not source of interrupt
RO/LH
0
1
INT1. 1= Auto-Negotiation Page Received, 0= not source of interrupt
RO/LH
0
0
Reserved.
RO/LH
0
Revision 1.3 (05-31-07)
110
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
5.5.12
Interrupt Mask
Index (In Decimal):
BITS
DESCRIPTION
15-8
7-0
30
Size:
16-bits
TYPE
DEFAULT
Reserved. Write as 0; ignore on read.
RO
0
Mask Bits. 1 = interrupt source is enabled 0 = interrupt source is masked
RW
0
TYPE
DEFAULT
Reserved.
RO
000b
Autodone. Auto-negotiation done indication:
0 = Auto-negotiation is not done or disabled (or not active)
1 = Auto-negotiation is done
RO
0b
11-5
Reserved. Write as 0000010b, ignore on Read.
RW
0000010b
4-2
Speed Indication. HCDSPEED value:
[001]=10Mbps half-duplex
[101]=10Mbps full-duplex
[010]=100Base-TX half-duplex
[110]=100Base-TX full-duplex
RO
See
Note 5.3
1-0
Reserved. Write as 0; ignore on Read
RO
00b
5.5.13
PHY Special Control/Status
Index (In Decimal):
BITS
15 - 13
12
31
Size:
DESCRIPTION
Note 5.3
SMSC LAN9118
16-bits
See Table 2.2, “Default Ethernet Settings,” on page 15, for default settings.
111
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Chapter 6 Timing Diagrams
6.1
Host Interface Timing
The LAN9118 supports the following host cycles:
Read Cycles:
„
PIO Reads (nCS or nRD controlled)
„
PIO Burst Reads (nCS or nRD controlled)
„
RX Data FIFO Direct PIO Reads (nCS or nRD controlled)
„
RX Data FIFO Direct PIO Burst Reads (nCS or nRD controlled)
Write Cycles:
6.1.1
„
PIO writes (nCS and nWR controlled)
„
TX Data FIFO direct PIO writes (nCS or nWR controlled)
Special Restrictions on Back-to-Back Write/Read Cycles
It is important to note that there are specific restrictions on the timing of back-to-back write-read
operations. These restrictions concern reading the control registers after any write cycle to the
LAN9118 device. In many cases there is a required minimum delay between writing to the LAN9118,
and the subsequent side effect (change in the control register value). For example, when writing to the
TX Data FIFO, it takes up to 135ns for the level indication to change in the TX_FIFO_INF register.
In order to prevent the host from reading stale data after a write operation, minimum wait periods must
be enforced. These periods are specified in Table 6.1, "Read After Write Timing Rules". The host
processor is required to wait the specified period of time after any write to the LAN9118 before reading
the resource specified in the table. These wait periods are for read operations that immediately follow
any write cycle. Note that the required wait period is dependant upon the register being read after the
write.
Performing "dummy" reads of the BYTE_TEST register is a convenient way to guarantee that the
minimum write-to-read timing restriction is met. Table 6.1 also shows the number of dummy reads that
are required before reading the register indicated. The number of BYTE_TEST reads in this table is
based on the minimum timing for Tcycle (45ns). For microprocessors with slower busses the number
of reads may be reduced as long as the total time is equal to, or greater than the time specified in the
table. Note that dummy reads of the BYTE_TEST register are not required as long as the minimum
time period is met.
Table 6.1 Read After Write Timing Rules
REGISTER NAME
MINIMUM WAIT TIME FOR READ
FOLLOWING ANY WRITE CYCLE
(IN NS)
NUMBER OF BYTE_TEST
READS
(ASSUMING TCYCLE OF 45NS)
ID_REV
0
0
IRQ_CFG
135
3
INT_STS
90
2
INT_EN
45
1
BYTE_TEST
0
0
FIFO_INT
45
1
Revision 1.3 (05-31-07)
112
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 6.1 Read After Write Timing Rules (continued)
6.1.2
REGISTER NAME
MINIMUM WAIT TIME FOR READ
FOLLOWING ANY WRITE CYCLE
(IN NS)
NUMBER OF BYTE_TEST
READS
(ASSUMING TCYCLE OF 45NS)
RX_CFG
45
1
TX_CFG
45
1
HW_CFG
45
1
RX_DP_CTRL
45
1
RX_FIFO_INF
0
0
TX_FIFO_INF
135
3
PMT_CTRL
315
7
GPIO_CFG
45
1
GPT_CFG
45
1
GPT_CNT
135
3
WORD_SWAP
45
1
FREE_RUN
180
4
RX_DROP
0
0
MAC_CSR_CMD
45
1
MAC_CSR_DATA
45
1
AFC_CFG
45
1
E2P_CMD
45
1
E2P_DATA
45
1
Special Restrictions on Back-to-Back Read Cycles
There are also restrictions on specific back-to-back read operations. These restrictions concern
reading specific registers after reading resources that have side effects. In many cases there is a delay
between reading the LAN9118, and the subsequent indication of the expected change in the control
register values.
In order to prevent the host from reading stale data on back-to-back reads, minimum wait periods have
been established. These periods are specified in Table 6.2, "Read After Read Timing Rules". The host
processor is required to wait the specified period of time between read operations of specific
combinations of resources. The wait period is dependant upon the combination of registers being read.
Performing "dummy" reads of the BYTE_TEST register is a convenient way to guarantee that the
minimum wait time restriction is met. Table 6.2 also shows the number of dummy reads that are
required for back-to-back read operations. The number of BYTE_TEST reads in this table is based on
the minimum timing for Tcycle (45ns). For microprocessors with slower busses the number of reads
may be reduced as long as the total time is equal to, or greater than the time specified in the table.
Dummy reads of the BYTE_TEST register are not required as long as the minimum time period is met.
SMSC LAN9118
113
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 6.2 Read After Read Timing Rules
AFTER
READING...
WAIT FOR THIS MANY
NS…
OR PERFORM THIS MANY
READS OF BYTE_TEST…
(ASSUMING Tcycle OF 45NS)
BEFORE READING...
RX Data FIFO
135
3
RX_FIFO_INF
RX Status FIFO
135
3
RX_FIFO_INF
TX Status FIFO
135
3
TX_FIFO_INF
RX_DROP
180
4
RX_DROP
6.2
PIO Reads
PIO reads can be used to access CSRs or RX Data and RX/TX status FIFOs. In this mode, counters
in the CSRs are latched at the beginning of the read cycle. Read data is valid as indicated in the timing
diagram. PIO reads can be performed using Chip Select (nCS) or Read Enable (nRD). Either or both
of these control signals must go high between cycles for the period specified.
PIO reads are supported for both 16- and 32-bit access. Timing for 16-bit and 32-bit PIO Read cycles
is identical with the exception that D[31:16] are not driven during a 16-bit read.
Note: Some registers have restrictions on the timing of back-to-back, write-read and read-read
cycles.
A[7:1]
nCS, nRD
Data Bus
Figure 6.1 LAN9118 PIO Read Cycle Timing
Note: The “Data Bus” width is 32 bits with optional support for 16-bit bus widths
Revision 1.3 (05-31-07)
114
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 6.3 PIO Read Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
Read Cycle Time
45
ns
tcsl
nCS, nRD Assertion Time
32
ns
tcsh
nCS, nRD Deassertion Time
13
ns
tcsdv
nCS, nRD Valid to Data Valid
tasu
Address Setup to nCS, nRD Valid
0
ns
tah
Address Hold Time
0
ns
tdon
Data Buffer Turn On Time
0
ns
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
tcycle
30
7
0
ns
ns
ns
Note: A PIO Read cycle begins when both nCS and nRD are asserted. The cycle ends when either
or both nCS and nRD are deasserted. They may be asserted and deasserted in any order.
6.3
PIO Burst Reads
In this mode, performance is improved by allowing up to 8, DWORD read cycles, or 16, WORD read
cycles back-to-back. PIO Burst Reads can be performed using Chip Select (nCS) or Read Enable
(nRD). Either or both of these control signals must go high between bursts for the period specified.
Timing for 16-bit and 32-bit PIO Burst Mode Read cycles is identical, with the exception that D[31:16]
are not driven during a 16-bit burst.
A[7:5]
A[4:1]
nCS, nRD
Data Bus
Figure 6.2 LAN9118 PIO Burst Read Cycle Timing
Note: The “Data Bus” width is 32 bits with optional support for 16-bit bus widths
SMSC LAN9118
115
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 6.4 PIO Burst Read Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
tcsh
nCS, nRD Deassertion Time
tcsdv
nCS, nRD Valid to Data Valid
tacyc
Address Cycle Time
45
tasu
Address Setup to nCS, nRD valid
0
tadv
Address Stable to Data Valid
tah
Address Hold Time
0
ns
tdon
Data Buffer Turn On Time
0
ns
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
13
ns
30
ns
ns
40
7
0
ns
ns
Note: A PIO Burst Read cycle begins when both nCS and nRD are asserted. The cycle ends when
either or both nCS and nRD are deasserted. They may be asserted and deasserted in any
order.
6.4
RX Data FIFO Direct PIO Reads
In this mode the upper address inputs are not decoded, and any read of the LAN9118 will read the
RX Data FIFO. This mode is enabled when FIFO_SEL is driven high during a read access. This is
normally accomplished by connecting the FIFO_SEL signal to high-order address line. This mode is
useful when the host processor must increment its address when accessing the LAN9118. Timing is
identical to a PIO read, and the FIFO_SEL signal has the same timing characteristics as the address
lines.
Timing for 16-bit and 32-bit Direct PIO Read cycles is identical with the exception that D[31:16] is not
driven during a 16-bit read. Note that address lines A[2:1] are still used, and address bits A[7:3] are
ignored.
FIFO_SEL
A[2:1]
nCS, nRD
Data Bus
Figure 6.3 RX Data FIFO Direct PIO Read Cycle Timing
Note: The “Data Bus” width is 32 bits with optional support for 16-bit bus widths
Revision 1.3 (05-31-07)
116
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 6.5 RX Data FIFO Direct PIO Read Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
Read Cycle Time
45
ns
tcsl
nCS, nRD Assertion Time
32
ns
tcsh
nCS, nRD Deassertion Time
13
ns
tcsdv
nCS, nRD Valid to Data Valid
tasu
Address, FIFO_SEL Setup to nCS, nRD Valid
0
ns
tah
Address, FIFO_SEL Hold Time
0
ns
tdon
Data Buffer Turn On Time
0
ns
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
tcycle
30
7
0
ns
ns
ns
Note: An RX Data FIFO Direct PIO Read cycle begins when both nCS and nRD are asserted. The
cycle ends when either or both nCS and nRD are de-asserted. They may be asserted and deasserted in any order.
6.5
RX Data FIFO Direct PIO Burst Reads
In this mode the upper address inputs are not decoded, and any burst read of the LAN9118 will read
the RX Data FIFO. This mode is enabled when FIFO_SEL is driven high during a read access. This
is normally accomplished by connecting the FIFO_SEL signal to a high-order address line. This mode
is useful when the host processor must increment its address when accessing the LAN9118. Timing
is identical to a PIO Burst Read, and the FIFO_SEL signal has the same timing characteristics as the
address lines.
In this mode, performance is improved by allowing an unlimited number of back-to-back DWORD or
WORD read cycles. RX Data FIFO Direct PIO Burst Reads can be performed using Chip Select (nCS)
or Read Enable (nRD). When either or both of these control signals go high, they must remain high
for the period specified.
Timing for 16-bit and 32-bit RX Data FIFO Direct PIO Burst Reads is identical with the exception that
D[31:16] are not driven during a 16-bit burst. Note that address lines A[2:1] are still used, and address
bits A[7:3] are ignored.
SMSC LAN9118
117
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
FIFO_SEL
A[2:1]
nCS, nRD
Data Bus
Figure 6.4 RX Data FIFO Direct PIO Burst Read Cycle Timing
Note: The “Data Bus” width is 32 bits with optional support for 16-bit bus widths
Table 6.6 RX Data FIFO Direct PIO Burst Read Cycle Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
tcsh
nCS, nRD Deassertion Time
tcsdv
nCS, nRD Valid to Data Valid
tacyc
Address Cycle Time
45
tasu
Address, FIFO_SEL Setup to nCS, nRD Valid
0
tadv
Address Stable to Data Valid
tah
Address, FIFO_SEL Hold Time
0
ns
tdon
Data Buffer Turn On Time
0
ns
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
13
ns
30
ns
ns
40
7
0
ns
ns
Note: An RX Data FIFO Direct PIO Burst Read cycle begins when both nCS and nRD are asserted.
The cycle ends when either or both nCS and nRD are deasserted. They may be asserted and
deasserted in any order.
6.6
PIO Writes
PIO writes are used for all LAN9118 write cycles. PIO writes can be performed using Chip Select (nCS)
or Write Enable (nWR). Either or both of these control signals must go high between cycles for the
period specified.
PIO Writes are valid for 16- and 32-bit access. Timing for 16-bit and 32-bit PIO write cycles are
identical with the exception that D[31:16] are ignored during a 16-bit write.
Revision 1.3 (05-31-07)
118
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
A[7:1]
nCS, nWR
Data Bus
Figure 6.5 PIO Write Cycle Timing
Note: The “Data Bus” width is 32 bits with optional support for 16-bit bus widths
Table 6.7 PIO Write Cycle Timing
SYMBOL
DESCRIPTION
tcycle
MIN
TYP
MAX
UNITS
Write Cycle Time
45
ns
tcsl
nCS, nWR Assertion Time
32
ns
tcsh
nCS, nWR Deassertion Time
13
ns
tasu
Address Setup to nCS, nWR Assertion
0
ns
tah
Address Hold Time
0
ns
tdsu
Data Setup to nCS, nWR Deassertion
7
ns
tdh
Data Hold Time
0
ns
Note: A PIO Write cycle begins when both nCS and nWR are asserted. The cycle ends when either
or both nCS and nWR are deasserted. They may be asserted and deasserted in any order.
6.7
TX Data FIFO Direct PIO Writes
In this mode the upper address inputs are not decoded, and any write to the LAN9118 will write the
TX Data FIFO. This mode is enabled when FIFO_SEL is driven high during a write access. This is
normally accomplished by connecting the FIFO_SEL signal to a high-order address line. This mode is
useful when the host processor must increment its address when accessing the LAN9118. Timing is
identical to a PIO write, and the FIFO_SEL signal has the same timing characteristics as the address
lines.
Timing for 16-bit and 32-bit cycles is identical with the exception that D[31:16] is ignored during a 16bit write. Note that address lines A[2:1] are still used when the LAN9118 is operating in 32-bit and 16bit mode. Address bits A[7:3] are ignored.
SMSC LAN9118
119
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
FIFO_SEL
A[2:1]
nCS, nWR
Data Bus
Figure 6.6 TX Data FIFO Direct PIO Write Timing
Note: The “Data Bus” width is 32 bits with optional support for 16-bit bus widths
Table 6.8 TX Data FIFO Direct PIO Write Timing
SYMBOL
tcycle
DESCRIPTION
MIN
TYP
MAX
UNITS
Write Cycle Time
45
ns
tcsl
nCS, nWR Assertion Time
32
ns
tcsh
nCS, nWR Deassertion Time
13
ns
tasu
Address, FIFO_SEL Setup to nCS, nWR Assertion
0
ns
tah
Address, FIFO_SEL Hold Time
0
ns
tdsu
Data Setup to nCS, nWR Deassertion
7
ns
tdh
Data Hold Time
0
ns
Note: A TX Data FIFO Direct PIO Write cycle begins when both nCS and nWR are asserted. The
cycle ends when either or both nCS and nWR are deasserted. They may be asserted and
deasserted in any order.
Revision 1.3 (05-31-07)
120
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
6.8
Reset Timing
T6.1
nRST
T6.2
T6.3
Configuration
signals
T6.4
Output drive
Table 6.9 Reset Timing
PARAMETER
DESCRIPTION
MIN
TYP
MAX
UNITS
T6.1
Reset Pulse Width
200
us
T6.2
Configuration input setup to
nRST rising
200
ns
T6.3
Configuration input hold after
nRST rising
10
ns
T6.4
Output Drive after nRST rising
6.9
16
NOTES
ns
EEPROM Timing
The following specifies the EEPROM timing requirements for the LAN9118
Figure 6.7 EEPROM Timing
SMSC LAN9118
121
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 6.10 EEPROM Timing Values
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
tCKCYC
EECLK Cycle time
1110
1130
ns
tCKH
EECLK High time
550
570
ns
tCKL
EECLK Low time
550
570
ns
tCSHCKH
EECS high before rising edge of EECLK
1070
ns
tCKLCSL
EECLK falling edge to EECS low
30
ns
tDVCKH
EEDIO valid before rising edge of EECLK
(OUTPUT)
550
ns
tCKHDIS
EEDIO disable after rising edge EECLK
(OUTPUT)
550
ns
tDSCKH
EEDIO setup to rising edge of EECLK (INPUT)
90
ns
tDHCKH
EEDIO hold after rising edge of EECLK
(INPUT)
0
ns
tCKLDIS
EECLK low to data disable (OUTPUT)
580
ns
tCSHDV
EEDIO valid after EECS high (VERIFY)
tDHCSL
EEDIO hold after EECS low (VERIFY)
tCSL
EECS low
Revision 1.3 (05-31-07)
122
DATASHEET
600
ns
0
ns
1070
ns
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Chapter 7 Operational Characteristics
7.1
Absolute Maximum Ratings*
Output Voltage (VDD_PLL, VDD_CORE) (Note 7.1) . . . . . . . . . . . . . . . . . . . . . . . . . .0V to +1.8V+10%
Supply Voltage (VDD_A, VDD_REF, VREG, VDD_IO) (Note 7.2) . . . . . . . . . . . . . . . .0V to +3.3V+10%
Positive voltage on signal pins, with respect to ground (Note 7.3) . . . . . . . . . . . . . . . . . . . . . . . . . . +6V
Negative voltage on signal pins, with respect to ground (Note 7.4) . . . . . . . . . . . . . . . . . . . . . . . . -0.5V
Positive voltage on XTAL1, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V
Positive voltage on XTAL2, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V
Ambient Operating Temperature in Still Air (TA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to +70oC
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65oC to +150oC
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..+/- 5kV
Note 7.1
These pins must not be used to supply power to other external devices.
Note 7.2
When powering this device from laboratory or system power supplies, it is important that
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested that a clamp circuit be used.
Note 7.3
This rating does not apply to the following pins: XTAL1, XTAL2, EXRES1.
Note 7.4
This rating does not apply to the following pins: EXRES1.
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 7.2, "Operating Conditions**", Section 7.5, "DC Electrical Specifications", or any other
applicable section of this specification is not implied.
7.2
Operating Conditions**
Output Voltage (VDD_PLL, VDD_CORE) (Note 7.5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +1.8V +/- 10%
Supply Voltage (VDD_A, VDD_REF, VREG, VDD_IO) . . . . . . . . . . . . . . . . . . . . . . . . . . +3.3V +/- 10%
Ambient Operating Temperature in Still Air (TA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to +70oC
Note 7.5
These pins must not be used to supply power to other external devices.
**Proper operation of the LAN9118 is guaranteed only within the ranges specified in this section.
SMSC LAN9118
123
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
7.3
Power Consumption Device Only
Power measurements taken under the following conditions:
Temperature: .................................................................................................................................. +25° C
Device VDD:..................................................................................................................................+3.30 V
Table 7.1 Power Consumption Device Only
MODE
TOTAL POWER - TYPICAL (MW)
10BASE-T Operation
D0, 10BASE-T /w traffic
244
D0, Idle
225
D1, 10BASE-T /w traffic
120
D1, Idle
120
D2, Energy Detect Power Down
35
D2, General Power Down
11
100BASE-TX Operation
D0, 100BASE-TX /w traffic
422
D0, Idle
367
D1, 100BASE-T /w traffic
262
D1, Idle
262
D2, Energy Detect Power Down (Cable disconnected)
35
D2, General Power Down
11
7.4
Note 7.6
Each LED indicator in use adds approximately 4 mA to the Digital power supply.
Note 7.7
D0 = Normal Operation, D1 = WOL (Wake On LAN mode), D2= Low Power Energy Detect.
Power Consumption Device and System Components
This section describes typical power consumption values of a total Ethernet LAN connectivity solution,
which includes external components supporting the SMSC Ethernet controller. The values below
should be used as comparision measurements only for power provisioning.
Please refer to application note “AN 12-5 Designing with the LAN9118 - Getting Started”, that can be
found on SMSC’s web site www.smsc.com, which details the magnetics and other components used.
Power measurements taken under the following conditions:
Temperature: .................................................................................................................................. +25° C
Device VDD:..................................................................................................................................+3.30 V
Revision 1.3 (05-31-07)
124
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 7.2 Power Consumption Device and System Components
MODE
TOTAL POWER - TYPICAL (MW)
10BASE-T Operation
D0, 10BASE-T /w traffic
614
D0, Idle
637
D1, 10BASE-T /w traffic
513
D1, Idle
513
D2, Energy Detect Power Down
56
D2, General Power Down
32
100BASE-TX Operation
D0, 100BASE-TX /w traffic
518
D0, Idle
576
D1, 100BASE-T /w traffic
414
D1, Idle
414
D2, Energy Detect Power Down
56
D2, General Power Down
32
Note 7.8
7.5
Each LED indicator in use adds approximately 4 mA to the Digital power supply.
DC Electrical Specifications
Table 7.3 I/O Buffer Characteristics
PARAMETER
SYMBOL
MIN
Low Input Level
VILI
High Input Level
TYP
MAX
UNITS
NOTES
-0.3
0.8
V
VIHI
2.0
5.5
V
Negative-Going Threshold
VILT
1.01
1.18
1.35
V
Schmitt Trigger
Positive-Going Threshold
VIHT
1.39
1.6
1.8
V
Schmitt Trigger
Schmitt Trigger Hysteresis
(VIHT - VILT)
VHYS
345
420
485
mV
0.4
V
IOL = 12mA
V
IOH = -12mA
I Type Input Buffer
IS Type Input Buffer
O12 Type Buffer
Low Output Level
VOL
High Output Level
VOH
SMSC LAN9118
VDD - 0.4
125
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 7.3 I/O Buffer Characteristics (continued)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
0.4
V
IOL = 12mA
OD12 Type Buffer
Low Output Level
VOL
IO8 Type Buffer
Low Input Level
VILI
-0.3
0.8
V
High Input Level
VIHI
2.0
5.5
V
Low Output Level
VOL
0.4
V
IOL = 8mA
High Output Level
VOH
V
IOH = -8mA
VDD - 0.4
OD8 Type Buffer
Low Output Level
VOL
0.4
V
IOL = 8mA
Low Output Level
VOL
0.4
V
IOL = 8mA
High Output Level
VOH
VDD - 0.4
V
IOH = -8mA
Low Input Level
VILCK
-0.3
0.5
V
High Input Level
VIHCK
1.4
3.6
V
O8 Type Buffer
ICLK Input Buffer
Table 7.4 100BASE-TX Tranceiver Characteristics
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
Peak Differential Output Voltage
High
VPPH
950
-
1050
mVpk
Note 7.9
Peak Differential Output Voltage
Low
VPPL
-950
-
-1050
mVpk
Note 7.9
Signal Amplitude Symmetry
VSS
98
-
102
%
Note 7.9
Signal Rise & Fall Time
TRF
3.0
-
5.0
nS
Note 7.9
Rise & Fall Time Symmetry
TRFS
-
-
0.5
nS
Note 7.9
Duty Cycle Distortion
DCD
35
50
65
%
Note 7.10
Overshoot & Undershoot
VOS
-
-
5
%
1.4
nS
Jitter
Note 7.9
Note 7.11
Measured at the line side of the transformer, line replaced by 100Ω (+/- 1%) resistor.
Note 7.10 Offset from16 nS pulse width at 50% of pulse peak
Note 7.11 Measured differentially.
Revision 1.3 (05-31-07)
126
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Table 7.5 10BASE-T Tranceiver Characteristics
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
Transmitter Peak Differential
Output Voltage
VOUT
2.2
2.5
2.8
V
Note 7.12
Receiver Differential Squelch
Threshold
VDS
300
420
585
mV
Note 7.12 Measured at the line side of the transformer, line replaced by 100Ω (+/- 1%) resistor.
7.6
Clock Circuit
The LAN9118 can accept either a 25MHz crystal (preferred) or a 25 MHz clock oscillator (±50 PPM)
input. The LAN9118 shares the 25MHz clock oscillator input (CLKIN) with the crystal input XTAL1 (pin
6). If the single-ended clock oscillator method is implemented, XTAL2 should be left unconnected and
CLKIN should be driven with a nominal 0-3.3V clock signal. The input clock duty cycle is 40%
minimum, 50% typical and 60% maximum.
It is recommended that a crystal utilizing matching parallel load capacitors be used for the LAN9118
crystal input/output signals (XTAL1, XTAL2). See Table 7.6, "LAN9118 Crystal Specifications" for crystal
specifications. Refer to SMSC Application Note AN10.7 - “Parallel Crystal Circuit Input Voltage Control”
and the LAN9118 Reference Schematic for additional information.
Table 7.6 LAN9118 Crystal Specifications
PARAMETER
SYMBOL
MIN
NOM
Crystal Cut
MAX
UNITS
NOTES
AT, typ
Crystal Oscillation Mode
Fundamental Mode
Crystal Calibration Mode
Parallel Resonant Mode
Frequency
Ffund
-
25.000
-
MHz
Frequency Tolerance @ 25oC
Ftol
-
-
+/-50
PPM
Note 7.13
Frequency Stability Over Temp
Ftemp
-
-
+/-50
PPM
Note 7.13
Frequency Deviation Over Time
Fage
-
+/-3 to 5
-
PPM
Note 7.14
-
-
+/-50
PPM
Note 7.15
Total Allowable PPM Budget
Shunt Capacitance
CO
-
7 typ
-
pF
Load Capacitance
CL
-
20 typ
-
pF
Drive Level
PW
0.5
-
-
mW
Equivalent Series Resistance
R1
-
-
30
Ohm
Operating Temperature Range
0
-
+70
oC
LAN9118 XTAL1 Pin
Capacitance
-
3 typ
-
pF
Note 7.16
LAN9118 XTAL2 Pin
Capacitance
-
3 typ
-
pF
Note 7.16
Note 7.13 The maximum allowable values for Frequency Tolerance and Frequency Stability are
application dependant. Since any particular application must meet the IEEE +/-50 PPM
Total PPM Budget, the combination of these two values must be approximately +/-45 PPM
(allowing for aging).
SMSC LAN9118
127
DATASHEET
Revision 1.3 (05-31-07)
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Note 7.14 Frequency Deviation Over Time is also reffered to as Aging.
Note 7.15 The total deviation for the Transmitter Clock Frequency is specified by IEEE 802.3u as
+/- 50 PPM.
Note 7.16 This number includes the pad, the bond wire and the lead frame. PCB capacitance is not
included in this value. The XTAL1 and XTAL2 pin and PCB capacitance values are
required to accurately calculate the value of the two external load capacitors. These two
external load capacitors determine the accuracy of the 25.000 MHz frequency.
Revision 1.3 (05-31-07)
128
DATASHEET
SMSC LAN9118
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Chapter 8 Package Outline
Figure 8.1 100 Pin TQFP Package Definition
Table 8.1 100 Pin TQFP Package Parameters
A
A1
A2
D
D1
E
E1
H
L
L1
e
q
W
R1
R2
ccc
MIN
~
NOMINAL
~
MAX
1.60
REMARKS
Overall Package Height
0.05
1.35
15.80
13.90
15.80
13.90
0.09
0.45
~
~
~
~
~
~
~
~
0.60
1.00
0.50 Basic
~
0.22
~
~
~
0.15
1.45
16.20
14.10
16.20
14.10
0.20
0.75
~
Standoff
Body Thickness
X Span
X body Size
Y Span
Y body Size
Lead Frame Thickness
Lead Foot Length
Lead Length
Lead Pitch
Lead Foot Angle
Lead Width
Lead Shoulder Radius
Lead Foot Radius
Coplanarity
0o
0.17
0.08
0.08
~
7o
0.27
~
0.20
0.08
Notes:
1. Controlling Unit: millimeter.
2. Tolerance on the true position of the leads is ± 0.04 mm maximum.
3. Package body dimensions D1 and E1 do not include the mold protrusion.
Maximum mold protrusion is 0.25 mm.
4. Dimension for foot length L measured at the gauge plane 0.25 mm above the seating plane.
5. Details of pin 1 identifier are optional but must be located within the zone indicated.
SMSC LAN9118
129
DATASHEET
Revision 1.3 (05-31-07)