CYPRESS CYDC128B08

CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
1.8V 4k/8k/16k x 16 and 8k/16k x 8
ConsuMoBL Dual-Port Static RAM
Features
• Lead (Pb)-free 14 x 14 x 1.4 mm 100-pin TQFP Package
• True dual-ported memory cells which allow simultaneous access of the same memory location
• Full asynchronous operation
• Pin select for Master or Slave
• Expandable data bus to 32 bits with Master/Slave chip
select when using more than one device
• 4/8/16k × 16 and 8/16k × 8 organization
• High-speed access: 40 ns
• On-chip arbitration logic
• Ultra Low operating power
• On-chip semaphore logic
— Active: ICC = 15 mA (typical) at 55 ns
• Input Read Registers and Output Drive Registers
— Active: ICC = 25 mA (typical) at 40 ns
— Standby: ISB3 = 2 µA (typical)
• INT flag for port-to-port communication
• Separate upper-byte and lower-byte control
• Port-independent 1.8V, 2.5V, and 3.0V I/Os
• Commercial and industrial temperature ranges
Selection Guide for VCC = 1.8V
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
-40
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
-55
1.8V-1.8V
1.8V-1.8V
Port I/O Voltages (P1-P2)
Unit
Maximum Access Time
40
55
ns
Typical Operating Current
25
15
mA
Typical Standby Current for ISB1
2
2
µA
Typical Standby Current for ISB3
2
2
µA
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
-40
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
-55
2.5V-2.5V
2.5V-2.5V
Selection Guide for VCC = 2.5V
Port I/O Voltages (P1-P2)
Unit
Maximum Access Time
40
55
ns
Typical Operating Current
39
28
mA
Typical Standby Current for ISB1
6
6
µA
Typical Standby Current for ISB3
4
4
µA
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
-40
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
-55
3.0V-3.0V
3.0V-3.0V
Selection Guide for VCC = 3.0V
Port I/O Voltages (P1-P2)
Unit
Maximum Access Time
40
55
ns
Typical Operating Current
49
42
mA
Typical Standby Current for ISB1
7
7
µA
Typical Standby Current for ISB3
6
6
µA
Cypress Semiconductor Corporation
Document #: 001-01638 Rev. *E
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised January 25, 2007
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
I/O[15:0]R
I/O[15:0]L
UBR
UBL
LBL
LBR
IO
Control
IO
Control
16K X 16
Dual Ported Array
Address Decode
Address Decode
A[13:0]L
CE L
A [13:0]R
CE R
Interrupt
Arbitration
Semaphore
OE L
R/W L
SEML
BUSY L
INTL
IRR0 ,IRR1
Mailboxes
INTR
OE R
R/W R
SEMR
BUSY R
M/S
Input Read
Register and
Output Drive
Register
CEL
OEL
R/WL
CE R
OE R
R/W R
ODR0 - ODR4
SFEN
Figure 1. Top Level Block Diagram[1, 2]
Notes:
1. A0–A11 for 4k devices; A0–A12 for 8k devices; A0–A13 for 16k devices.
2. BUSY is an output in master mode and an input in slave mode.
Document #: 001-01638 Rev. *E
Page 2 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Pin Configurations [3, 4, 5, 6, 7]
A3R
A2R
A1R
A0R
UBR
LBR
OER
R/WR
VSS
ODR4
ODR3
ODR2
VSS
ODR1
ODR0
VSS
SFEN
R/WL
OEL
LBL
UBL
A0L
A1L
A2L
A3L
100-Pin TQFP (Top View)
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
A4L
1
75
A4R
A5L
2
74
A5R
A6L
3
73
A6R
A7L
4
72
A7R
A8L
5
71
A8R
CEL
6
70
CER
SEML
7
69
SEMR
INTL
8
68
INTR
BUSYL
9
67
BUSYR
66
A9R
65
A10R
64
VSS
63
VCC
CYDC064B16
CYDC128B16
CYDC256B16
A9L
10
A10L
11
VSS
12
VCC
13
A11L
14
62
A11R
A12L[3]
15
61
A12R[3]
IRR0[5]
16
60
IRR1[6]
M/S
17
59
NC[7]
VDDIOL
18
58
VDDIOR
I/O0L
19
57
I/O15R
I/O1L
20
56
I/O14R
I/O2L
21
55
I/O13R
VSS
22
54
VSS
I/O3L
23
53
I/O12R
I/O4L
24
52
I/O11R
I/O5L
25
51
I/O10R
I/O9R
I/O8R
VDDIOR
I/O7R
I/O6R
I/O5R
VSS
I/O4R
I/O3R
I/O2R
I/O1R
I/O0R
NC[7]
I/O15L
I/O14L
I/O13L
I/O12L
I/O11L
VSS
I/O10L
I/O9L
I/O8L
VDDIOL
I/O7L
I/O6L
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Notes:
3. A12L and A12R are NC pins for CYDC064B16.
4. IRR functionality is not supported for the CYDC256B16 device.
5. This pin is A13L for CYDC256B16 device.
6. This pin is A13R for CYDC256B16 device.
7. Leave this pin unconnected. No trace or power component can be connected to this pin.
Document #: 001-01638 Rev. *E
Page 3 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Pin Configurations (continued)[7, 8, 9, 10]
A3R
A2R
A1R
A0R
UBR
LBR
OER
R/WR
VSS
ODR4
ODR3
ODR2
VSS
ODR1
ODR0
VSS
SFEN
R/WL
OEL
LBL
UBL
A0L
A1L
A2L
A3L
100-pin TQFP (Top View)
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
A4L
1
75
A4R
A5L
2
74
A5R
A6L
3
73
A6R
A7L
4
72
A7R
A8L
5
71
A8R
CEL
6
70
CER
SEML
7
69
SEMR
INTL
8
68
INTR
BUSYL
9
67
BUSYR
A9L
10
66
A9R
A10L
11
65
A10R
VSS
12
64
VSS
VCC
13
63
VCC
A11L
14
62
A11R
A12L
15
61
A12R
IRR0[9]
16
60
IRR1[10]
M/S
17
59
NC[11]
VDDIOL
18
58
VDDIOR
I/O0L
19
57
VSS
I/O1L
20
56
VSS
I/O2L
21
55
VSS
VSS
22
54
VSS
I/O3L
23
53
VSS
I/O4L
24
52
VSS
I/O5L
25
51
VSS
CYDC064B08
CYDC128B08
VSS
VSS
VDDIOR
I/O7R
I/O6R
I/O5R
VSS
I/O4R
I/O3R
I/O2R
I/O1R
I/O0R
NC[11]
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDDIOL
I/O7L
I/O6L
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Notes:
8. IRR functionality is not supported for the CYDC128B08 device.
9. This pin is A13L for CYDC128B08 devices.
10. This pin is A13R for CYDC128B08 devices.
Document #: 001-01638 Rev. *E
Page 4 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Pin Definitions
Left Port
Right Port
Description
CEL
CER
Chip Enable
R/WL
R/WR
Read/Write Enable
OEL
OER
Output Enable
A0L–A13L
A0R–A13R
Address (A0–A11 for 4k devices; A0–A12 for 8k devices; A0–A13 for 16k devices).
I/O0L–I/O15L
I/O0R–I/O15R
Data Bus Input/Output for x16 devices; I/O0–I/O7 for x8 devices.
SEML
SEMR
Semaphore Enable
UBL
UBR
Upper Byte Select (I/O8–I/O15 for x16 devices; Not applicable for x8 devices).
LBL
LBR
Lower Byte Select (I/O0–I/O7 for x16 devices; Not applicable for x8 devices).
INTL
INTR
Interrupt Flag
BUSYL
BUSYR
Busy Flag
IRR0, IRR1
ODR0-ODR4
SFEN
Input Read Register for CYDC064B16, CYDC064B08, CYDC128B16.
A13L, A13R for CYDC256B16 and CYDC128B08 devices.
Output Drive Register; These outputs are Open Drain.
Special Function Enable
M/S
Master or Slave Select
VCC
Core Power
GND
Ground
VDDIOL
Left Port I/O Voltage
VDDIOR
Right Port I/O Voltage
NC
No Connect. Leave this pin Unconnected.
Functional Description
The
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08, CYDC064B08 are low-power CMOS 4k,
8k,16k x 16, and 8/16k x 8 dual-port static RAMs. Arbitration
schemes are included on the devices to handle situations
when multiple processors access the same piece of data. Two
ports are provided, permitting independent, asynchronous
access for reads and writes to any location in memory. The
devices can be utilized as standalone 16-bit dual-port static
RAMs or multiple devices can be combined in order to function
as a 32-bit or wider master/slave dual-port static RAM. An M/S
pin is provided for implementing 32-bit or wider memory applications without the need for separate master and slave
devices or additional discrete logic. Application areas include
interprocessor/multiprocessor designs, communications
status buffering, and dual-port video/graphics memory.
Each port has independent control pins: Chip Enable (CE),
Read or Write Enable (R/W), and Output Enable (OE). Two
flags are provided on each port (BUSY and INT). BUSY
signals that the port is trying to access the same location
currently being accessed by the other port. The Interrupt flag
(INT) permits communication between ports or systems by
means of a mail box. The semaphores are used to pass a flag,
or token, from one port to the other to indicate that a shared
resource is in use. The semaphore logic is comprised of eight
shared latches. Only one side can control the latch
(semaphore) at any time. Control of a semaphore indicates
that a shared resource is in use. An automatic power-down
feature is controlled independently on each port by a Chip
Enable (CE) pin.
Document #: 001-01638 Rev. *E
The
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08, CYDC064B08 are available in 100-pin TQFP
packages.
Power Supply
The core voltage (VCC) can be 1.8V, 2.5V or 3.0V, as long as
it is lower than or equal to the I/O voltage.
Each port can operate on independent I/O voltages. This is
determined by what is connected to the VDDIOL and VDDIOR
pins. The supported I/O standards are 1.8V/2.5V LVCMOS
and 3.0V LVTTL.
Write Operation
Data must be set up for a duration of tSD before the rising edge
of R/W in order to guarantee a valid write. A write operation is
controlled by either the R/W pin (see Write Cycle No. 1
waveform) or the CE pin (see Write Cycle No. 2 waveform).
Required inputs for non-contention operations are summarized in Table 1.
If a location is being written to by one port and the opposite
port attempts to read that location, a port-to-port flowthrough
delay must occur before the data is read on the output;
otherwise the data read is not deterministic. Data will be valid
on the port tDDD after the data is presented on the other port.
Read Operation
When reading the device, the user must assert both the OE
and CE pins. Data will be available tACE after CE or tDOE after
OE is asserted. If the user wishes to access a semaphore flag,
Page 5 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
then the SEM pin must be asserted instead of the CE pin, and
OE must also be asserted.
Interrupts
The upper two memory locations may be used for message
passing. The highest memory location (FFF for the
CYDC064B16, 1FFF for the CYDC128B16 and CYDC064B08,
3FFF for the CYDC256B16 and CYDC128B08) is the mailbox
for the right port and the second-highest memory location (FFE
for the CYDC064B16, 1FFE for the CYDC128B16 and
CYDC064B08, 3FFE for the CYDC256B16 and CYDC128B08)
is the mailbox for the left port. When one port writes to the
other port’s mailbox, an interrupt is generated to the owner.
The interrupt is reset when the owner reads the contents of the
mailbox. The message is user-defined.
Each port can read the other port’s mailbox without resetting
the interrupt. The active state of the busy signal (to a port)
prevents the port from setting the interrupt to the winning port.
Also, an active busy to a port prevents that port from reading
its own mailbox and, thus, resetting the interrupt to it.
If an application does not require message passing, do not
connect the interrupt pin to the processor’s interrupt request
input pin. On power up, an initialization program should be run
and the interrupts for both ports must be read to reset them.
The operation of the interrupts and their interaction with Busy
are summarized in Table 2.
Busy
The
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08, CYDC064B08 provide on-chip arbitration to
resolve simultaneous memory location access (contention). If
both ports’ CEs are asserted and an address match occurs
within tPS of each other, the busy logic will determine which
port has access. If tPS is violated, one port will definitely gain
permission to the location, but it is not predictable which port
will get that permission. BUSY will be asserted tBLA after an
address match or tBLC after CE is taken LOW.
Master/Slave
A M/S pin is provided in order to expand the word width by
configuring the device as either a master or a slave. The BUSY
output of the master is connected to the BUSY input of the
slave. This will allow the device to interface to a master device
with no external components. Writing to slave devices must be
delayed until after the BUSY input has settled (tBLC or tBLA),
otherwise, the slave chip may begin a write cycle during a
contention situation. When tied HIGH, the M/S pin allows the
device to be used as a master and, therefore, the BUSY line
is an output. BUSY can then be used to send the arbitration
outcome to a slave.
Input Read Register
The Input Read Register (IRR) captures the status of two
external input devices that are connected to the Input Read
pins.
The contents of the IRR read from address x0000 from either
port. During reads from the IRR, DQ0 and DQ1 are valid bits
and DQ<15:2> are don’t care. Writes to address x0000 are not
allowed from either port.
Address x0000 is not available for standard memory accesses
when SFEN = VIL. When SFEN = VIH, address x0000 is
available for memory accesses.
Document #: 001-01638 Rev. *E
The inputs will be 1.8V/2.5V LVCMOS or 3.0V LVTTL,
depending on the core voltage supply (VCC). Refer to Table 3
for Input Read Register operation.
IRR is not available in the CYDC256B16 and CYDC128B08,
as the IRR pins are used as extra address pins A13L and A13R.
Output Drive Register
The Output Drive Register (ODR) determines the state of up
to five external binary state devices by providing a path to VSS
for the external circuit. These outputs are Open Drain.
The five external devices can operate at different voltages
(1.5V ≤ VDDIO ≤ 3.5V) but the combined current cannot exceed
40 mA (8 mA max for each external device). The status of the
ODR bits are set using standard write accesses from either
port to address x0001 with a “1” corresponding to on and “0”
corresponding to off.
The status of the ODR bits can be read with a standard read
access to address x0001. When SFEN = VIL, the ODR is active
and address x0001 is not available for memory accesses.
When SFEN = VIH, the ODR is inactive and address x0001 can
be used for standard accesses.
During reads and writes to ODR DQ<4:0> are valid and
DQ<15:5> are don’t care. Refer to Table 4 for Output Drive
Register operation.
Semaphore Operation
The
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08, CYDC064B08 provide eight semaphore
latches, which are separate from the dual-port memory
locations. Semaphores are used to reserve resources that are
shared between the two ports. The state of the semaphore
indicates that a resource is in use. For example, if the left port
wants to request a given resource, it sets a latch by writing a
zero to a semaphore location. The left port then verifies its
success in setting the latch by reading it. After writing to the
semaphore, SEM or OE must be deasserted for tSOP before
attempting to read the semaphore. The semaphore value will
be available tSWRD + tDOE after the rising edge of the
semaphore write. If the left port was successful (reads a zero),
it assumes control of the shared resource, otherwise (reads a
one) it assumes the right port has control and continues to poll
the semaphore. When the right side has relinquished control
of the semaphore (by writing a one), the left side will succeed
in gaining control of the semaphore. If the left side no longer
requires the semaphore, a one is written to cancel its request.
Semaphores are accessed by asserting SEM LOW. The SEM
pin functions as a chip select for the semaphore latches (CE
must remain HIGH during SEM LOW). A0–2 represents the
semaphore address. OE and R/W are used in the same
manner as a normal memory access. When writing or reading
a semaphore, the other address pins have no effect.
When writing to the semaphore, only I/O0 is used. If a zero is
written to the left port of an available semaphore, a one will
appear at the same semaphore address on the right port. That
semaphore can now only be modified by the side showing zero
(the left port in this case). If the left port now relinquishes
control by writing a one to the semaphore, the semaphore will
be set to one for both sides. However, if the right port had
requested the semaphore (written a zero) while the left port
had control, the right port would immediately own the
semaphore as soon as the left port released it. Table 5 shows
sample semaphore operations.
Page 6 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
When reading a semaphore, all sixteen/eight data lines output
the semaphore value. The read value is latched in an output
register to prevent the semaphore from changing state during
a write from the other port. If both ports attempt to access the
semaphore within tSPS of each other, the semaphore will
definitely be obtained by one side or the other, but there is no
guarantee which side will control the semaphore. On
power-up, both ports should write “1” to all eight semaphores.
Architecture
The
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08, CYDC064B08 consist of an array of 4k, 8k, or
16k words of 16 dual-port RAM cells, I/O and address lines,
and control signals (CE, OE, R/W). The CYDC064B08 and
CYDC128B08 consist of an array of 8k and 16k words of 8
each of dual-port RAM cells, I/O and address lines, and control
signals (CE, OE, R/W).These control pins permit independent
access for reads or writes to any location in memory. To handle
simultaneous writes/reads to the same location, a BUSY pin is
provided on each port. Two Interrupt (INT) pins can be utilized
for port-to-port communication. Two Semaphore (SEM)
control pins are used for allocating shared resources. With the
M/S pin, the devices can function as a master (BUSY pins are
outputs) or as a slave (BUSY pins are inputs). The devices
also have an automatic power-down feature controlled by CE.
Each port is provided with its own output enable control (OE),
which allows data to be read from the device.
Table 1. Non-Contending Read/Write
Inputs
Outputs
I/O8–I/O15[11]
CE
R/W
OE
UB
LB
SEM
I/O0–I/O7
H
X
X
X
X
H
X
X
X
H
H
H
High Z
High Z
Deselected: Power-down
L
L
X
L
H
H
Data In
High Z
Write to Upper Byte Only
L
L
X
H
L
H
High Z
Data In
Write to Lower Byte Only
L
L
X
L
L
H
Data In
Data In
Write to Both Bytes
L
H
L
L
H
H
Data Out
High Z
Read Upper Byte Only
L
H
L
H
L
H
High Z
Data Out
Read Lower Byte Only
L
H
L
L
L
H
Data Out
Data Out
Read Both Bytes
X
X
H
X
X
X
High Z
High Z
Outputs Disabled
H
H
L
X
X
L
Data Out
Data Out
Read Data in Semaphore Flag
X
H
L
H
H
L
Data Out
Data Out
Read Data in Semaphore Flag
H
X
X
X
L
Data In
Data In
Write DIN0 into Semaphore Flag
X
X
H
H
L
Data In
Data In
Write DIN0 into Semaphore Flag
High Z
High Z
Operation
Deselected: Power-down
L
X
X
L
X
L
Not Allowed
L
X
X
X
L
L
Not Allowed
Table 2. Interrupt Operation Example (Assumes BUSYL = BUSYR = HIGH)[12]
Left Port
Function
Set Right INTR Flag
R/WL
L
CEL
L
OEL
X
Right Port
A0L–13L
3FFF
INTL
R/WR
CER
OER
A0R–13R
INTR
X
X
X
X
X
L[14]
[15]
[15]
H[13]
Reset Right INTR Flag
X
X
X
X
X
X
L
L
3FFF
Set Left INTL Flag
X
X
X
X
L[13]
L
L
X
3FFE[15]
X
[14]
X
X
X
X
X
Reset Left INTL Flag
X
L
L
3FFE
[15]
H
Notes:
11. This column applies to x16 devices only.
12. See Interrupts Functional Description for specific highest memory locations by device.
13. If BUSYR = L, then no change.
14. If BUSYL = L, then no change.
15. See Functional Description for specific addresses by device.
Document #: 001-01638 Rev. *E
Page 7 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Table 3. Input Read Register Operation[16, 19]
SFEN
H
L
CE
L
L
R/W
OE
H
UB
L
H
LB
L
L
ADDR
I/O0–I/O1 I/O2–I/O15
[17]
L
x0000-Max VALID
X
L
x0000
UB
LB
ADDR
[18]
VALID
[17]
VALID
X
Mode
Standard Memory Access
IRR Read
Table 4. Output Drive Register [20]
SFEN
CE
R/W
H
L
H
L
L
L
L
L
OE
X
H
[21]
[17]
L
X
X
L
X
I/O0–I/O4 I/O5–I/O15
Mode
[17]
[17]
x0000-Max VALID
VALID
Standard Memory Access
[17]
L
L
L
x0001
VALID[18]
X
ODR Write[20, 22]
x0001
[18]
X
ODR Read[20]
VALID
Table 5. Semaphore Operation Example
Function
No action
I/O0–I/O15 Left I/O0–I/O15 Right
1
1
Status
Semaphore-free
Left port writes 0 to semaphore
0
1
Left Port has semaphore token
Right port writes 0 to semaphore
0
1
No change. Right side has no write access to semaphore
Left port writes 1 to semaphore
1
0
Right port obtains semaphore token
Left port writes 0 to semaphore
1
0
No change. Left port has no write access to semaphore
Right port writes 1 to semaphore
0
1
Left port obtains semaphore token
Left port writes 1 to semaphore
1
1
Semaphore-free
Right port writes 0 to semaphore
1
0
Right port has semaphore token
Right port writes 1 to semaphore
1
1
Semaphore free
Left port writes 0 to semaphore
0
1
Left port has semaphore token
Left port writes 1 to semaphore
1
1
Semaphore-free
Notes:
16. SFEN = VIL for IRR reads.
17. UB or LB = VIL. If LB = VIL, then DQ<7:0> are valid. If UB = VIL then DQ<15:8> are valid.
18. LB must be active (LB = VIL) for these bits to be valid.
19. SFEN active when either CEL = VIL or CER = VIL. It is inactive when CEL = CER = VIH.
20. SFEN = VIL for ODR reads and writes.
21. Output enable must be low (OE = VIL) during reads for valid data to be output.
22. During ODR writes data will also be written to the memory.
Document #: 001-01638 Rev. *E
Page 8 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Maximum Ratings[23]
Output Current into Outputs (LOW)............................. 90 mA
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Supply Voltage to Ground Potential ............... –0.5V to +3.3V
DC Voltage Applied to
Outputs in High-Z State..........................–0.5V to VCC + 0.5V
DC Input Voltage[24] ...............................–0.5V to VCC + 0.5V
Static Discharge Voltage.......................................... > 2000V
Latch-up Current.................................................... > 200 mA
Operating Range
Range
Ambient Temperature
VCC
0°C to +70°C
1.8V ± 100 mV
2.5V ± 100 mV
3.0V ± 300 mV
–40°C to +85°C
1.8V ± 100 mV
2.5V ± 100 mV
3.0V ± 300 mV
Commercial
Industrial
Electrical Characteristics for VCC = 1.8V Over the Operating Range
Parameter
VOH
VOL
VOL ODR
Description
P1 I/O
P2 I/O
Voltage Voltage
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
-40
-55
Min.
VIL
IOZ
ICEX ODR
Max.
Min.
Typ.
Max. Unit
Output HIGH Voltage (IOH = –100 µA)
1.8V (any port)
VDDIO
– 0.2
VDDIO
– 0.2
V
Output HIGH Voltage (IOH = –2 mA)
2.5V (any port)
2.0
2.0
V
Output HIGH Voltage (IOH = –2 mA)
3.0V (any port)
2.1
2.1
V
Output LOW Voltage (IOL = 100 µA)
1.8V (any port)
0.2
0.2
V
Output HIGH Voltage (IOL = 2 mA)
2.5V (any port)
0.4
0.4
V
Output HIGH Voltage (IOL = 2 mA)
3.0V (any port)
0.4
0.4
V
ODR Output LOW Voltage (IOL = 8 mA)
1.8V (any port)
0.2
0.2
V
2.5V (any port)
0.2
0.2
V
3.0V (any port)
VIH
Typ.
Input HIGH Voltage
Input LOW Voltage
Output Leakage Current
ODR Output Leakage Current.
VOUT = VDDIO
0.2
V
1.8V (any port)
1.2
VDDIO
+ 0.2
0.2
1.2
VDDIO
+ 0.2
V
2.5V (any port)
1.7
VDDIO
+ 0.3
1.7
VDDIO
+ 0.3
V
3.0V (any port)
2.0
VDDIO
+ 0.2
2.0
VDDIO
+ 0.2
V
1.8V (any port)
–0.2
0.4
–0.2
0.4
V
2.5V (any port)
–0.3
0.6
–0.3
0.6
V
3.0V (any port)
–0.2
0.7
–0.2
0.7
V
1.8V
1.8V
–1
1
–1
1
µA
2.5V
2.5V
–1
1
–1
1
µA
3.0V
3.0V
–1
1
–1
1
µA
1.8V
1.8V
–1
1
–1
1
µA
2.5V
2.5V
–1
1
–1
1
µA
3.0V
3.0V
–1
1
–1
1
µA
Notes:
23. The voltage on any input or I/O pin can not exceed the power pin during power-up.
24. Pulse width < 20 ns.
Document #: 001-01638 Rev. *E
Page 9 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Electrical Characteristics for VCC = 1.8V (continued) Over the Operating Range
Parameter
IIX
P1 I/O
P2 I/O
Voltage Voltage
Description
Input Leakage Current
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
-40
-55
Min.
Typ.
Max.
Min.
Typ.
Max. Unit
1.8V
1.8V
–1
1
–1
1
µA
2.5V
2.5V
–1
1
–1
1
µA
3.0V
3.0V
–1
1
–1
1
µA
ICC
Operating Current (VCC = Max.,
IOUT = 0 mA) Outputs Disabled
Ind.
1.8V
1.8V
25
40
15
25
mA
ISB1
Standby Current (Both Ports TTL Ind.
Level) CEL and CER ≥ VCC – 0.2,
SEML = SEMR = VCC – 0.2, f = fMAX
1.8V
1.8V
2
6
2
6
µA
ISB2
Standby Current (One Port TTL
Level) CEL | CER ≥ VIH, f = fMAX
Ind.
1.8V
1.8V
8.5
18
8.5
14
mA
ISB3
Standby Current (Both Ports
CMOS Level) CEL & CER ≥
VCC − 0.2V, SEML and SEMR >
VCC – 0.2V, f = 0
Ind.
1.8V
1.8V
2
6
2
6
µA
ISB4
Standby Current (One Port CMOS Ind.
Level) CEL | CER ≥ VIH, f = fMAX[25]
1.8V
1.8V
8.5
18
8.5
14
mA
Notes:
25. fMAX = 1/tRC = All inputs cycling at f = 1/tRC (except output enable). f = 0 means no address or control lines change. This applies only to inputs at CMOS level
standby ISB3.
Document #: 001-01638 Rev. *E
Page 10 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Electrical Characteristics for VCC = 2.5V Over the Operating Range
Parameter
Description
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
-40
-55
P1 I/O
P2 I/O
Voltage Voltage
Min.
2.5V (any port)
2.0
2.1
Typ.
Max.
Min.
Typ.
Max. Unit
VOH
Output HIGH Voltage (IOH = –2 mA)
2.0
V
Output HIGH Voltage (IOH = –2 mA)
3.0V (any port)
VOL
Output LOW Voltage (IOL = 2 mA)
2.5V (any port)
0.4
0.4
V
2.1
V
Output LOW Voltage (IOL = 2 mA)
3.0V (any port)
0.4
0.4
V
VOL ODR
ODR Output LOW Voltage (IOL = 8 mA)
2.5V (any port)
0.2
0.2
V
VIH
Input HIGH Voltage
3.0V (any port)
0.2
V
2.5V (any port)
1.7
VDDIO
+ 0.3
0.2
1.7
VDDIO
+ 0.3
V
3.0V (any port)
2.0
VDDIO
+ 0.2
2.0
VDDIO
+ 0.2
V
2.5V (any port)
–0.3
0.6
–0.3
0.6
V
3.0V (any port)
VIL
Input LOW Voltage
IOZ
Output Leakage Current
ICEX ODR
ODR Output Leakage Current.
VOUT = VCC
3.0V
IIX
Input Leakage Current
2.5V
3.0V
3.0V
–1
1
µA
ICC
Operating Current (VCC = Max.,
IOUT = 0 mA) Outputs Disabled
Ind.
2.5V
2.5V
39
55
28
40
mA
ISB1
Standby Current (Both Ports TTL Ind.
Level) CEL and CER ≥ VCC – 0.2,
SEM L= SEMR = VCC – 0.2, f=fMAX
2.5V
2.5V
6
8
6
8
µA
ISB2
Standby Current (One Port TTL
Level) CEL | CER ≥ VIH, f = fMAX
Ind.
2.5V
2.5V
21
30
18
25
mA
ISB3
Standby Current (Both Ports
CMOS Level) CEL & CER ≥
VCC − 0.2V, SEML and SEMR >
VCC – 0.2V, f = 0
Ind.
2.5V
2.5V
4
6
4
6
µA
ISB4
Standby Current (One Port CMOS Ind.
Level) CEL | CER ≥ VIH, f = fMAX[25]
2.5V
2.5V
21
30
18
25
mA
Document #: 001-01638 Rev. *E
–0.2
0.7
–0.2
0.7
V
2.5V
2.5V
–1
1
–1
1
µA
3.0V
3.0V
–1
1
–1
1
µA
2.5V
2.5V
–1
1
–1
1
µA
3.0V
–1
1
–1
1
µA
2.5V
–1
1
–1
1
µA
1
–1
Page 11 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Electrical Characteristics for 3.0V Over the Operating Range
Parameter
Description
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
-40
-55
P1 I/O
P2 I/O
Voltage Voltage
Min.
3.0V (any port)
2.1
Typ.
Max.
Min.
Typ.
Max. Unit
VOH
Output HIGH Voltage (IOH = –2 mA)
2.1
V
VOL
Output LOW Voltage (IOL = 2 mA)
3.0V (any port)
0.4
0.4
V
VOL ODR
ODR Output LOW Voltage (IOL = 8 mA)
3.0V (any port)
0.2
0.2
V
VIH
Input HIGH Voltage
3.0V (any port)
2.0
VDDIO
+ 0.2
2.0
VDDIO
+ 0.2
V
VIL
Input LOW Voltage
3.0V (any port)
–0.2
0.7
–0.2
0.7
V
IOZ
Output Leakage Current
3.0V
3.0V
–1
1
–1
1
µA
ICEX ODR
ODR Output Leakage Current.
VOUT = VCC
3.0V
3.0V
–1
1
–1
1
µA
IIX
Input Leakage Current
3.0V
3.0V
–1
1
–1
1
µA
ICC
Operating Current (VCC = Max.,
IOUT = 0 mA) Outputs Disabled
Ind.
3.0V
3.0V
49
70
42
60
mA
ISB1
Standby Current (Both Ports TTL Ind.
Level) CEL and CER ≥ VCC – 0.2,
SEML = SEMR = VCC – 0.2, f = fMAX
3.0V
3.0V
7
10
7
10
µA
ISB2
Standby Current (One Port TTL
Level) CEL | CER ≥ VIH, f = fMAX
Ind.
3.0V
3.0V
28
40
25
35
mA
ISB3
Standby Current (Both Ports
CMOS Level) CEL & CER ≥
VCC − 0.2V, SEML and SEMR >
VCC – 0.2V, f = 0
Ind.
3.0V
3.0V
6
8
6
8
µA
ISB4
Standby Current (One Port CMOS Ind.
Level) CEL | CER ≥ VIH, f = fMAX[25]
3.0V
3.0V
28
40
25
35
mA
Capacitance[26]
Parameter
Description
CIN
Input Capacitance
COUT
Output Capacitance
Test Conditions
TA = 25°C, f = 1 MHz,
VCC = 3.0V
Max.
Unit
9
pF
10
pF
Note:
26. Tested initially and after any design or process changes that may affect these parameters.
Document #: 001-01638 Rev. *E
Page 12 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
AC Test Loads and Waveforms
7
3.0V/2.5V/1.8V
3.0V/2.5V/1.8V
R1
RTH = 6 kΩ
OUTPUT
OUTPUT
R1
OUTPUT
C = 30 pF
C = 30 pF
R2
VTH = 0.8V
(a) Normal Load (Load 1)
(b) Thévenin Equivalent (Load 1)
1.8V
R1
1022Ω
13500Ω
1.8V
R2
792Ω
10800Ω
GND
10%
R2
(c) Three-State Delay (Load 2)
(Used for tLZ, tHZ, tHZWE, and tLZWE
including scope and jig)
ALL INPUT PULSES
3.0V/2.5V
C = 5 pF
90%
10%
90%
≤ 3 ns
≤ 3 ns
Switching Characteristics for VCC = 1.8V Over the Operating Range[27]
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
-40
Parameter
Description
Min.
-55
Max.
Min.
Max.
Unit
Read Cycle
tRC
Read Cycle Time
tAA
Address to Data Valid
tOHA
Output Hold From Address Change
tACE[28]
CE LOW to Data Valid
40
55
ns
tDOE
OE LOW to Data Valid
25
30
ns
tLZOE
[29, 30, 31]
OE Low to Low Z
tHZOE[29, 30, 31]
OE HIGH to High Z
tLZCE[29, 30, 31]
tHZCE[29, 30, 31]
tPU[31]
tPD[31]
tABE[28]
CE LOW to Low Z
40
40
5
ns
55
5
5
5
ns
25
5
15
0
ns
ns
5
15
CE HIGH to High Z
CE LOW to Power-Up
55
ns
ns
25
0
ns
ns
CE HIGH to Power-Down
40
55
ns
Byte Enable Access Time
40
55
ns
Write Cycle
tWC
Write Cycle Time
40
55
ns
tSCE[28]
CE LOW to Write End
30
45
ns
tAW
Address Valid to Write End
30
45
ns
Notes:
27. Test conditions assume signal transition time of 3 ns or less, timing reference levels of VCC/2, input pulse levels of 0 to VCC, and output loading of the specified
IOI/IOH and 30-pF load capacitance.
28. To access RAM, CE = L, UB = L, SEM = H. To access semaphore, CE = H and SEM = L. Either condition must be valid for the entire tSCE time.
29. At any given temperature and voltage condition for any given device, tHZCE is less than tLZCE and tHZOE is less than tLZOE.
30. Test conditions used are Load 3.
31. This parameter is guaranteed but not tested. For information on port-to-port delay through RAM cells from writing port to reading port, refer to Read Timing with
Busy waveform
Document #: 001-01638 Rev. *E
Page 13 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Switching Characteristics for VCC = 1.8V Over the Operating Range[27] (continued)
Parameter
Description
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
-40
-55
Min.
Max.
Min.
Max.
Unit
tHA
Address Hold From Write End
0
0
ns
tSA[28]
Address Set-up to Write Start
0
0
ns
tPWE
Write Pulse Width
25
40
ns
tSD
Data Set-up to Write End
20
30
ns
tHD
Data Hold From Write End
0
0
ns
tHZWE[30, 31]
tLZWE[30, 31]
tWDD[32]
tDDD[32]
R/W LOW to High Z
R/W HIGH to Low Z
15
0
25
0
ns
ns
Write Pulse to Data Delay
55
80
ns
Write Data Valid to Read Data Valid
55
80
ns
tBLA
BUSY LOW from Address Match
30
45
ns
tBHA
BUSY HIGH from Address Mismatch
30
45
ns
tBLC
BUSY LOW from CE LOW
30
45
ns
tBHC
BUSY HIGH from CE HIGH
30
45
ns
tPS[34]
Port Set-up for Priority
tWB
R/W HIGH after BUSY (Slave)
tWH
R/W HIGH after BUSY HIGH (Slave)
Busy Timing
[33]
tBDD[35]
5
5
ns
0
0
ns
20
35
ns
BUSY HIGH to Data Valid
30
40
ns
[33]
Interrupt Timing
tINS
INT Set Time
35
45
ns
tINR
INT Reset Time
35
45
ns
Semaphore Timing
tSOP
SEM Flag Update Pulse (OE or SEM)
10
15
ns
tSWRD
SEM Flag Write to Read Time
10
10
ns
tSPS
SEM Flag Contention Window
10
10
ns
tSAA
SEM Address Access Time
40
55
ns
Notes:
32. For information on port-to-port delay through RAM cells from writing port to reading port, refer to Read Timing with Busy waveform.
33. Test conditions used are Load 2.
34. Add 2ns to this value when the I/O ports are operating at different voltages.
35. tBDD is a calculated parameter and is the greater of tWDD–tPWE (actual) or tDDD–tSD (actual).
Document #: 001-01638 Rev. *E
Page 14 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Switching Characteristics for VCC = 2.5V Over the Operating Range
Parameter
Description
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
-40
-55
Min.
Max.
Min.
Max.
Unit
Read Cycle
tRC
Read Cycle Time
tAA
Address to Data Valid
tOHA
Output Hold From Address Change
tACE[28]
CE LOW to Data Valid
40
55
ns
tDOE
OE LOW to Data Valid
25
30
ns
tLZOE
[29, 30, 31]
OE Low to Low Z
tHZOE[29, 30, 31]
tLZCE[29, 30, 31]
tHZCE[29, 30, 31]
tPU[31]
tPD[31]
tABE[28]
40
40
5
CE LOW to Power-Up
55
15
ns
15
2
15
0
ns
ns
2
2
CE HIGH to High Z
ns
5
2
OE HIGH to High Z
CE LOW to Low Z
55
ns
ns
15
0
ns
ns
CE HIGH to Power-Down
40
55
ns
Byte Enable Access Time
40
55
ns
Write Cycle
tWC
Write Cycle Time
tSCE[28]
CE LOW to Write End
30
45
ns
tAW
Address Valid to Write End
30
45
ns
tHA
Address Hold From Write End
0
0
ns
tSA[28]
Address Set-up to Write Start
0
0
ns
tPWE
Write Pulse Width
25
40
ns
tSD
Data Set-up to Write End
20
30
ns
tHD
Data Hold From Write End
0
0
ns
tHZWE[30, 31]
tLZWE[30, 31]
tWDD[32]
tDDD[32]
R/W LOW to High Z
Busy Timing
R/W HIGH to Low Z
40
55
15
0
ns
25
ns
0
ns
Write Pulse to Data Delay
55
80
ns
Write Data Valid to Read Data Valid
55
80
ns
[33]
tBLA
BUSY LOW from Address Match
30
45
ns
tBHA
BUSY HIGH from Address Mismatch
30
45
ns
tBLC
BUSY LOW from CE LOW
30
45
ns
tBHC
BUSY HIGH from CE HIGH
30
45
ns
tPS[34]
Port Set-up for Priority
5
5
ns
tWB
R/W HIGH after BUSY (Slave)
0
0
ns
tWH
R/W HIGH after BUSY HIGH (Slave)
20
35
ns
tBDD[35]
BUSY HIGH to Data Valid
Document #: 001-01638 Rev. *E
30
40
ns
Page 15 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Switching Characteristics for VCC = 2.5V Over the Operating Range (continued)
Parameter
Description
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
-40
-55
Min.
Max.
Min.
Max.
Unit
Interrupt Timing[33]
tINS
INT Set Time
35
45
ns
tINR
INT Reset Time
35
45
ns
Semaphore Timing
tSOP
SEM Flag Update Pulse (OE or SEM)
10
15
ns
tSWRD
SEM Flag Write to Read Time
10
10
ns
tSPS
SEM Flag Contention Window
10
10
ns
tSAA
SEM Address Access Time
40
55
ns
Switching Characteristics for VCC = 3.0V Over the Operating Range
Parameter
Description
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
-40
-55
Min.
Max.
Min.
Unit
Max.
Read Cycle
tRC
Read Cycle Time
tAA
Address to Data Valid
tOHA
Output Hold From Address Change
tACE[28]
CE LOW to Data Valid
40
55
ns
tDOE
OE LOW to Data Valid
25
30
ns
tLZOE
[29, 30, 31]
tHZOE[29, 30, 31]
tLZCE[29, 30, 31]
tHZCE[29, 30, 31]
tPU[31]
tPD[31]
tABE[28]
OE Low to Low Z
40
40
5
CE LOW to Power-Up
55
15
ns
15
1
15
0
ns
ns
1
1
CE HIGH to High Z
ns
5
1
OE HIGH to High Z
CE LOW to Low Z
55
ns
ns
15
0
ns
ns
CE HIGH to Power-Down
40
55
ns
Byte Enable Access Time
40
55
ns
Write Cycle
tWC
Write Cycle Time
tSCE[28]
CE LOW to Write End
30
45
ns
tAW
Address Valid to Write End
30
45
ns
tHA
Address Hold From Write End
0
0
ns
tSA[28]
Address Set-up to Write Start
0
0
ns
tPWE
Write Pulse Width
25
40
ns
tSD
Data Set-up to Write End
20
30
ns
tHD
Data Hold From Write End
0
0
ns
Document #: 001-01638 Rev. *E
40
55
ns
Page 16 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Switching Characteristics for VCC = 3.0V Over the Operating Range (continued)
Parameter
Description
tHZWE[30, 31]
R/W LOW to High Z
[30, 31]
R/W HIGH to Low Z
tLZWE
tWDD[32]
tDDD[32]
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
CYDC256B16,
CYDC128B16,
CYDC064B16,
CYDC128B08,
CYDC064B08
-40
-55
Min.
Max.
Min.
15
0
Unit
Max.
25
0
ns
ns
Write Pulse to Data Delay
55
80
ns
Write Data Valid to Read Data Valid
55
80
ns
tBLA
BUSY LOW from Address Match
30
45
ns
tBHA
BUSY HIGH from Address Mismatch
30
45
ns
tBLC
BUSY LOW from CE LOW
30
45
ns
tBHC
BUSY HIGH from CE HIGH
30
45
ns
tPS[34]
Port Set-up for Priority
5
5
ns
tWB
R/W HIGH after BUSY (Slave)
0
0
ns
tWH
R/W HIGH after BUSY HIGH (Slave)
20
tBDD[35]
BUSY HIGH to Data Valid
Busy Timing[33]
35
ns
30
40
ns
Interrupt Timing[33]
tINS
INT Set Time
35
45
ns
tINR
INT Reset Time
35
45
ns
Semaphore Timing
tSOP
SEM Flag Update Pulse (OE or SEM)
10
15
ns
tSWRD
SEM Flag Write to Read Time
10
10
ns
tSPS
SEM Flag Contention Window
10
tSAA
SEM Address Access Time
Document #: 001-01638 Rev. *E
10
40
ns
55
ns
Page 17 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Switching Waveforms
Read Cycle No.1 (Either Port Address Access)[36, 37, 38]
tRC
ADDRESS
tOHA
DATA OUT
tAA
tOHA
PREVIOUS DATA VALID
DATA VALID
Read Cycle No.2 (Either Port CE/OE Access)[36, 39, 40]
tACE
CE and
LB or UB
tHZCE
tDOE
OE
tHZOE
tLZOE
DATA VALID
DATA OUT
tLZCE
tPU
CURRENT
tPD
ICC
ISB
Read Cycle No. 3 (Either Port)[36, 38, 41, 42]
tRC
ADDRESS
tOHA
tAA
UB or LB
tHZCE
tLZCE
tABE
CE
tHZCE
tACE
tLZCE
DATA OUT
Notes:
36. R/W is HIGH for read cycles.
37. Device is continuously selected CE = VIL and UB or LB = VIL. This waveform cannot be used for semaphore reads.
38. OE = VIL.
39. Address valid prior to or coincident with CE transition LOW.
40. To access RAM, CE = VIL, UB or LB = VIL, SEM = VIH. To access semaphore, CE = VIH, SEM = VIL.
41. R/W must be HIGH during all address transitions.
42. A write occurs during the overlap (tSCE or tPWE) of a LOW CE or SEM and a LOW UB or LB.
Document #: 001-01638 Rev. *E
Page 18 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Switching Waveforms (continued)
Write Cycle No.1: R/W Controlled Timing[41, 42, 43, 44, 45, 46]
tWC
ADDRESS
tHZOE [47]
OE
tAW
CE
[45, 46]
tPWE[44]
tSA
tHA
R/W
tHZWE[47]
DATA OUT
tLZWE
NOTE 48
NOTE 48
tSD
tHD
DATA IN
Write Cycle No. 2: CE Controlled Timing[41, 42, 43, 48]
tWC
ADDRESS
tAW
CE
[45, 46]
tSA
tSCE
tHA
R/W
tSD
tHD
DATA IN
Notes:
43. tHA is measured from the earlier of CE or R/W or (SEM or R/W) going HIGH at the end of write cycle.
44. If OE is LOW during a R/W controlled write cycle, the write pulse width must be the larger of tPWE or (tHZWE + tSD) to allow the I/O drivers to turn off and data to
be placed on the bus for the required tSD. If OE is HIGH during an R/W controlled write cycle, this requirement does not apply and the write pulse can be as short
as the specified tPWE.
45. To access RAM, CE = VIL, SEM = VIH.
46. To access upper byte, CE = VIL, UB = VIL, SEM = VIH.
To access lower byte, CE = VIL, LB = VIL, SEM = VIH.
47. Transition is measured ±0 mV from steady state with a 5-pF load (including scope and jig). This parameter is sampled and not 100% tested.
48. During this period, the I/O pins are in the output state, and input signals must not be applied.
Document #: 001-01638 Rev. *E
Page 19 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Switching Waveforms (continued)
Semaphore Read After Write Timing, Either Side[49, 50]
tSAA
A0–A2
VALID ADRESS
VALID ADRESS
tAW
tACE
tHA
SEM
tOHA
tSCE
tSOP
tSD
I/O0
DATAIN VALID
tSA
tPWE
DATAOUT VALID
tHD
R/W
tSWRD
tDOE
tSOP
OE
WRITE CYCLE
READ CYCLE
Timing Diagram of Semaphore Contention[51, 52]
A0L–A2L
MATCH
R/WL
SEML
tSPS
A0R–A2R
MATCH
R/WR
SEMR
Notes:
49. If the CE or SEM LOW transition occurs simultaneously with or after the R/W LOW transition, the outputs remain in the high-impedance state.
50. CE = HIGH for the duration of the above timing (both write and read cycle).
51. I/O0R = I/O0L = LOW (request semaphore); CER = CEL = HIGH.
52. If tSPS is violated, the semaphore will definitely be obtained by one side or the other, but which side will get the semaphore is unpredictable.
Document #: 001-01638 Rev. *E
Page 20 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Switching Waveforms (continued)
Timing Diagram of Read with BUSY (M/S=HIGH)[53]
tWC
ADDRESSR
MATCH
tPWE
R/WR
tHD
tSD
DATA INR
VALID
tPS
ADDRESSL
MATCH
tBLA
tBHA
BUSYL
tBDD
tDDD
DATAOUTL
VALID
tWDD
Write Timing with Busy Input (M/S = LOW)
tPWE
R/W
BUSY
tWB
tWH
Note:
53. CEL = CER = LOW.
Document #: 001-01638 Rev. *E
Page 21 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Switching Waveforms (continued)
Busy Timing Diagram No.1 (CE Arbitration)
CEL Valid First[54]
ADDRESSL,R
ADDRESS MATCH
CEL
tPS
CER
tBLC
tBHC
BUSYR
CER Valid First
ADDRESS L,R
ADDRESS MATCH
CER
tPS
CEL
tBLC
tBHC
BUSYL
Busy Timing Diagram No.2 (Address Arbitration)[54]
Left Address Valid First
tRC or tWC
ADDRESSL
ADDRESS MATCH
ADDRESS MISMATCH
tPS
ADDRESSR
tBLA
tBHA
BUSYR
Right Address Valid First
tRC or tWC
ADDRESSR
ADDRESS MATCH
ADDRESS MISMATCH
tPS
ADDRESSL
tBLA
tBHA
BUSYL
Note:
54. If tPS is violated, the busy signal will be asserted on one side or the other, but there is no guarantee to which side BUSY will be asserted.
Document #: 001-01638 Rev. *E
Page 22 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Switching Waveforms (continued)
Interrupt Timing Diagrams
Left Side Sets INTR:
ADDRESSL
tWC
WRITE 1FFF (OR 1/3FFF)
tHA[55]
CEL
R/WL
INTR
tINS [56]
Right Side Clears INTR:
tRC
READ 1FFF
(OR 1/3FFF)
ADDRESSR
CER
tINR [56]
R/WR
OER
INTR
Right Side Sets INTL:
ADDRESSR
tWC
WRITE 1FFE (OR 1/3FFE)
tHA[55]
CER
R/WR
INTL
[56]
tINS
Left Side Clears INTL:
tRC
READ 1FFE
OR 1/3FFE)
ADDRESSR
CEL
tINR[56]
R/WL
OEL
INTL
Notes:
55. tHA depends on which enable pin (CEL or R/WL) is deasserted first.
56. tINS or tINR depends on which enable pin (CEL or R/WL) is asserted last.
Document #: 001-01638 Rev. *E
Page 23 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Ordering Information
16k x16 1.8V Asynchronous Dual-Port SRAM
Speed
(ns)
Ordering Code
Package
Name
Package Type
Operating
Range
40
CYDC256B16-40AXC
AZ0AB
100-pin Lead-free TQFP
Commercial
55
CYDC256B16-55AXC
AZ0AB
100-pin Lead-free TQFP
Commercial
55
CYDC256B16-55AXI
AZ0AB
100-pin Lead-free TQFP
Industrial
8k x16 1.8V Asynchronous Dual-Port SRAM
Speed
(ns)
Ordering Code
Package
Name
Package Type
Operating
Range
40
CYDC128B16-40AXC
AZ0AB
100-pin Lead-free TQFP
Commercial
55
CYDC128B16-55AXC
AZ0AB
100-pin Lead-free TQFP
Commercial
55
CYDC128B16-55AXI
AZ0AB
100-pin Lead-free TQFP
Industrial
4k x16 1.8V Asynchronous Dual-Port SRAM
Speed
(ns)
Ordering Code
Package
Name
Package Type
Operating
Range
40
CYDC064B16-40AXC
AZ0AB
100-pin Lead-free TQFP
Commercial
55
CYDC064B16-55AXC
AZ0AB
100-pin Lead-free TQFP
Commercial
55
CYDC064B16-55AXI
AZ0AB
100-pin Lead-free TQFP
Industrial
16k x8 1.8V Asynchronous Dual-Port SRAM
Speed
(ns)
Ordering Code
Package
Name
Package Type
Operating
Range
40
CYDC128B08-40AXC
AZ0AB
100-pin Lead-free TQFP
Commercial
55
CYDC128B08-55AXC
AZ0AB
100-pin Lead-free TQFP
Commercial
55
CYDC128B08-55AXI
AZ0AB
100-pin Lead-free TQFP
Industrial
8k x8 1.8V Asynchronous Dual-Port SRAM
Speed
(ns)
Ordering Code
Package
Name
Package Type
Operating
Range
40
CYDC064B08-40AXC
AZ0AB
100-pin Lead-free TQFP
Commercial
55
CYDC064B08-55AXC
AZ0AB
100-pin Lead-free TQFP
Commercial
55
CYDC064B08-55AXI
AZ0AB
100-pin Lead-free TQFP
Industrial
Document #: 001-01638 Rev. *E
Page 24 of 26
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Package Diagram
100-Pin Thin Plastic Quad Flat Pack (TQFP) A100
51-85048-*C
All products and company names mentioned in this document may be the trademarks of their respective holders.
Document #: 001-01638 Rev. *E
Page 25 of 26
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
CYDC256B16, CYDC128B16,
CYDC064B16, CYDC128B08,
CYDC064B08
Document History Page
Document Title: CYDC256B16/CYDC128B16/CYDC064B16/CYDC128B08/CYDC064B08 1.8V 4k/8k/16k x 16 and 8k/16k
x 8 ConsuMoBL Dual-Port Static RAM
Document Number: 001-01638
REV.
ECN NO.
Issue Date
Orig. of
Change
Description of Change
**
385185
SEE ECN
YDT
New data sheet
*A
396697
SEE ECN
KGH
Updated ISB2 and ISB4 typo to mA.
Updated tINS and tINR for -55 to 31ns.
*B
404777
SEE ECN
KGH
Updated IOH and IOL values for the 1.8V, 2.5V and 3.0V parameters VOH and
VOL
Replaced -35 speed bin with -40
Updated Switching Characteristics for VCC = 2.5V and VCC = 3.0V
Included note 34
*C
463014
SEE ECN
HKH
Changed spec title to from “Consumer Dual-Port” to “ConsuMoBL Dual-Port”
Cypress Internet Release
*D
505803
SEE ECN
HKH
Corrected typo in Features and Ordering Info sections.
Cypress external web release.
*E
735537
SEE ECN
HKH
Corrected typo in Pg5 power supply section
Updated tDDD timing value to be consistent with tWDD
Document #: 001-01638 Rev. *E
Page 26 of 26
[+] Feedback