CORCOM Product Guide Compact RFI Filter with IEC Connector for Higher Frequency Applications EJT Series UL Recognized CSA Certified VDE Approved* EJT1 EJT8 EJT Series Specifications The EJT Series is a power inlet filter designed to attenuate noise up to 1 GHz. This inlet uses an IEC 320/C14 input connector which gives it a maximum rating of 15 amps. The EJT series is flange-mounted with optional outputs of 1/4" terminals or wire leads. This product was designed to address the demand for more noise attenuation at higher frequencies in a compact inlet. Now also available with an IEC 320/C20 connector with a maximum rating of 20 amps. Maximum leakage current,each line-to-ground 1-15 Amp @ 120 VAC 60 Hz: .22 mA @ 250 VAC 50 Hz: .38 mA Hipot rating (one minute): line-to-ground 2250 VDC line-to-line 1450 VDC Operating frequency: *15EJT - VDE rated at 10 amps, 250 VAC 20EJT - VDE rated at 16 amps, 250 VAC Rated voltage (max.): Minimum insertion loss in dB: Line-to-ground in 50 ohm circuit Electrical Schematics 1-15 Amp LINE LOAD Current Rating 01A 03A 06A 10A 15A 20A .15 27 22 13 7 4 - .5 33 30 21 14 10 8 20 Amp .20 mA .40 mA 1500 VAC 1450 VDC 50/60 Hz 250 VAC Frequency-MHz 1 5 10 40 59 65 34 57 63 27 51 60 21 43 52 15 38 48 15 42 50 30 65 69 65 61 63 60 100 61 61 59 61 63 58 1000 14 10 14 14 14 14 30 65 59 65 63 56 48 100 45 52 55 53 45 50 1000 14 17 20 18 23 10 Line-to-line in 50 ohm circuit Current Rating 01A 03A 06A 10A 15A 20A 20 Amp .15 10 10 10 10 10 9 .5 20 20 21 21 20 20 Frequency-MHz 1 5 10 23 43 52 51 24 41 24 37 48 25 28 44 26 25 36 26 40 35 Resistor location for reference only. 52 Catalog 1654001 Revised 05-07 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA Cust. Svc.: 1-800-468-2023 CORCOM Prods: 1-847-680-7400 Germany: 49-89-6089-0 www.corcom.com www.tycoelectronics.com CORCOM Product Guide Compact RFI Filter with IEC Connector for Higher Frequency Applications (Continued) EJT Series Case Dimensions EJT1 Part No. C 1-15A EJT1 B D E A 1-15A EJT8 EJT8 20EJT1 4.0 101.6 20EJT8 F E RFI Power Line Filters Case Styles D A B (max) (max) C D E F (max) (max) (max) (max) 2.87 72.9 2.23 56.6 3.8 96.52 3.2 81.28 0.875 22.2 0.875 22.2 1.18 29.99 1.18 29.99 1.19 30.2 1.19 30.2 1.350 34.29 1.350 34.29 1.575 40.0 1.575 40.0 1.654 42.01 1.654 42.01 1.98 — 50.3 1.98 0.295 50.3 7.5 2.087 — 53.00 2.087 — 53.00 B F Part Numbers C 01EJT1 03EJT1 06EJT1 10EJT1 15EJT1 20EJT1 Line Cord No. A Typical dimensions: Wire Leads: 4.0 [101.6] Min. - 18 AWG 01EJT8 03EJT8 06EJT8 10EJT8 15EJT8 20EJT8 GA400 20EJT1 Recommended Panel Cutout A D C B 1 to 15 Amp ∅ .140 3.56 1.035 [26.29] 0.126 Dia. with 0.236 x 90° Countersink for #4 Flat Head Screw (2X) .820 20.83 E 0.650 16.51 max. 0.25 Terminal with 0.069 (± .003) dia. hole (2 places) E 1.200 30.48 1.575 40.00 Label 0.25 Terminal with 0.069 x 0.155 Slot R .062 1.57 Panel Cutout (front mount) Panel Cutout (Front Mount) Tolerance ±.005 [0.13] Tolerance +/- 0.005 20EJT8 20 Amp A D C 4.0 101.6 min. E 0.138 Dia. (2X) 3.51 R 0.118 3.00 1.035 [26.29] Wire, #14 AWG UL 1015 (3 places) 0.126 Dia. with 0.236 x 90° Countersink for #4 Flat Head Screw (2X) B 1.055 26.80 0.528 13.41 1.370 34.80 E Label Brown (Line) Green / Yellow (Ground) Blue (Neutral) 1.654 42.01 Panel Cutout (front mount) Tolerance ±.005 [0.13] 53 Catalog 1654001 Revised 05-07 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA Cust. Svc.: 1-800-468-2023 CORCOM Prods: 1-847-680-7400 Germany: 49-89-6089-0 www.corcom.com www.tycoelectronics.com