BOURNS PEC11

NT
IA
PL
M
CO
S
oH
*R
Features
■
■
■
■
Applications
Push switch option
Compact, rugged design
High reliability
Metal bushing/shaft
Level control, tuning and timer settings in:
■ Audio-visual equipment
■ Consumer electric appliances
■ Radios
■ Musical instrumentation
■ Communications equipment
PEC11 Series - 12 mm Incremental Encoder
Electrical Characteristics
Output ................................................................................................................................................................................................................2-bit gray code
Closed Circuit Resistance ..............................................................................................................................................................................3 ohms maximum
Contact Rating ....................................................................................................................................................................................................1 mA @ 5 VDC
Insulation Resistance ........................................................................................................................................................................100 megohms @ 250 VDC
Dielectric Withstanding Voltage
Sea Level ..................................................................................................................................................................................................300 VAC minimum
Electrical Travel ........................................................................................................................................................................................................Continuous
Contact Bounce (15 RPM) ..............................................................................................................................................................................5.0 ms maximum
RPM (Operating) ....................................................................................................................................................................................................60 maximum
Environmental Characteristics
Operating Temperature Range ..........................................................................................................................................-30 °C to +70 °C (-22 °F to +158 °F)
Storage Temperature Range ............................................................................................................................................-40 °C to +85 °C (-40 °F to +185 °F)
Humidity....................................................................................................................................................................MIL-STD-202, Method 103B, Condition B
Vibration ..............................................................................................................................................................................................................................30 G
Contact Bounce ..................................................................................................................................................10~55~10 Hz / 1 min. / Amplitude 1.5 mm
Shock ................................................................................................................................................................................................................................100 G
Rotational Life........................................................................................................................................................................................30,000 cycles minimum
Switch Life ............................................................................................................................................................................................20,000 cycles minimum
IP Rating ..............................................................................................................................................................................................................................IP 40
Mechanical Characteristics
Mechanical Angle ............................................................................................................................................................................................360 ° continuous
Torque
Running ..........................................................................................................................................................................50 to 200 gf.cm (0.68 to 2.7 oz.-in.)
Mounting ........................................................................................................................................................................10.2 kgf.cm (8.83 lb.-in.) maximum
Shaft Side Load (Static) ..................................................................................................................................................................2.04 kgf (4.5 lbs.) minimum
Weight ................................................................................................................................................................................................5 gm (0.17 oz.) maximum
Terminals ....................................................................................................................................................................................Printed circuit board terminals
Soldering Condition
Wave Soldering........................................................................................Sn95.5/Ag2.8/Cu0.7 solder with no-clean flux: 260 °C max. for 3-5 seconds
Hand Soldering ....................................................................................................................................................................................Not recommended
Hardware ........................................................................................................................One flat washer and one mounting nut supplied with each encoder.
Switch Characteristics
Switch Type ......................................................................................................................................................................Contact Push ON Momentary SPST
Power Rating (Resistive Load) ........................................................................................................................................................................10 mA at 5 V DC
Switch Travel ..........................................................................................................................................................................................................0.5 ± 0.2 mm
Switch Actuation Force ..........................................................................................................................................................610 ± 306 gf (8.47 ± 4.24 oz.-in.)
How To Order
Quadrature Output Table
PEC11 - 4 0 20 F - S 0012
CW
Model
Terminal Configuration
4 = PC Pin Horizontal/Rear Facing
OFF
A Signal
Detent Option
0 = No Detents (12, 18, 24 pulses)
1 = 18 Detents (18 pulses)
2 = 24 Detents (12, 24 pulses)
ON
B Signal
Standard Shaft Length
15 = 15.0 mm
20 = 20.0 mm
25 = 25.0 mm
30 = 30.0 mm
D
Shaft Style
F = Metal Flatted Shaft
K = Metal Knurled Shaft*
Switch Configuration
S = Push Momentary Switch
N = No Switch
Resolution
0012 = 12 Pulses per 360 ° Rotation
0018 = 18 Pulses per 360 ° Rotation
0024 = 24 Pulses per 360 ° Rotation
* Metal knurled shaft with no switch is available in 15, 20 and 30 mm shaft lengths.
Metal knurled shaft with push momentary switch is available in 15 and 20 mm shaft lengths.
*RoHS Directive 2002/95/EC Jan 27 2003 including Annex
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
PEC11 Series - 12 mm Incremental Encoder
Product Dimensions
PEC11-4xxxF-Nxxxx
6.5
(.256)
L1
12.5
(.492)
LB
13.2
(.520)
2 PLCS.
1.8
(.071)
C0.5
13.2
(.520)
7.5
(.295)
l
A
0.9
(.035)
2.5
(.098)
4.5 +0/-0.05
(.177 +0/-.002)
3.5
6.0
(.138)
DIA.
(.236)
MOUNTING SURFACE
M7x0.75
C
2 PLCS.
2.6
(.102)
B
A
14.0
(.551)
2.5
(.098)
C
B
2.5
(.098)
1.0 +0.1/-0
(.039 +.004/-0)
DIA. 3 PLCS.
2.5
(.098)
A CHANNEL A
C COMMON
B CHANNEL B
PEC11-4xxxF-Sxxxx
6.5
(.256)
L1
SWITCH
TRAVEL
0.5
(.020)
LB
13.2
(.520)
12.5
(.492)
5.0
(.197)
2 PLCS.
1.8
(.071)
C0.5
7.0
(.276)
13.2
(.520)
7.5
(.295)
l
0.9
(.035)
2.5
(.098)
4.5 +0/-0.05
M7x0.75
(.177 +0/-.002)
3.5
6.0
(.138)
DIA.
(.236)
MOUNTING SURFACE
A
C
2 PLCS.
2.6
(.102)
B
A
14.0
(.551)
2.5
(.098)
C
2.5
(.098)
B
1.0
DIA. 5 PLCS.
(.039)
2.5
(.098)
A CHANNEL A
C COMMON
B CHANNEL B
L1
LB
l
15
(.591)
5.0
(.197)
7.0
(.276)
20
(.787)
7.0
(.276)
10.0
(.394)
25
(.984)
7.0
(.276)
12.0
(.472)
30
(1.181)
7.0
(.276)
12.0
(.472)
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
DIMENSIONS:
MM
(INCHES)
PEC11 Series - 12 mm Incremental Encoder
Product Dimensions
PEC11-4xxxK-Nxxxx
3.5
(.138)
6.5
(.256)
12.5
(.492)
L
LB
13.2
(.520)
P
2.4
7.0 (.094)
(.276)
2 PLCS.
1.8 +0.2/-0
(.071 +.008/-0)
A
13.2
(.520)
7.5
(.295)
2.6 +0.2/-0
(.102 +.008/-0)
2 PLCS.
7.5
(.295)
1.0
(.039)
A
A
M7x0.75
6.0 +0/-0.1
DIA.
(.236 +0/-.004)
C
C
B
B
5.0
(.197)
5.0
(.197)
1.0 +0.2/-0
(.039 +.008/-0)
DIA. 3 PLCS.
A CHANNEL A
C COMMON
B CHANNEL B
L
LB
P
A
15
(.591)
5.0
(.197)
7.0
(.276)
6.0
(.236)
20
(.787)
7.0
(.276)
7.0
(.276)
6.0
(.236)
30
(1.181)
7.0
(.276)
16.0
(.630)
12.0
(.472)
PEC11-4xxxK-Sxxxx
3.5
(.138)
6.5
(.256)
LB
SWITCH
TRAVEL
0.5
(.020)
P
A
2.4
7.0 (.094)
(.276)
13.2
(.520)
12.5
(.492)
L
5.0
(.197)
5.0
(.197)
2 PLCS.
1.8 +0.2/-0
(.071 +.008/-0)
7.0
(.276)
13.2
(.520)
7.5
(.295)
7.5
(.295)
1.0
(.039)
A
M7x0.75
DIA.
C
A
B
5.0
(.197)
6.0 +0/-0.1
(.236 +0/-.004)
2.5
(.098)
A CHANNEL A
C COMMON
B CHANNEL B
L
LB
P
A
15
(.591)
5.0
(.197)
7.0
(.276)
6.0
(.236)
20
(.787)
7.0
(.276)
7.0
(.276)
6.0
(.236)
C
B
2.6 +0.2/-0
(.102 +.008/-0)
2 PLCS.
1.0 +0.2/-0
DIA. 5 PLCS.
(.039 +.008/-0)
2.5
(.098)
DIMENSIONS:
MM
(INCHES)
REV. 03/08
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.